American Standard Plumbing Product 41751 User Manual

Installation  
Instructions  
4175.100  
COLONY SOFT  
SINGLE CONTROL  
KITCHEN PULL-OUT FAUCET  
Thank you for selecting American-Standard...  
the benchmark of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--  
Certified to comply with ANSI A112.18.1M  
please read these instructions carefully before you begin.  
M968986 Rev. 1.3  
RECOMMENDED TOOLS  
Phillips Screwdriver  
Regular Screwdriver  
Adjustable Wrench  
Plumbers' Putty or Caulking  
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON  
1
Turn off water at  
CAUTION  
main supply.  
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).  
Insert supply HOSES (2) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface.  
Follow mounting instructions below to secure faucet to mounting surface.  
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Insert supply HOSES (2) and  
SHANK (3) through mounting hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.  
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).  
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside  
of sink or mounting surface. Hand tighten LOCKNUT (6) and check that rotation of HANDLE (7) from HOT to COLD  
is centered.  
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening  
the screws slightly each time until all are snug to ensure even pressure.  
7
7
A
B
SPOUT BASE  
1
3
2
PUTTY  
2
4
3
SINK OR  
MOUNTING  
SURFACE  
4
5
5
8
6
8
6
 
CHECK CONNECTIONS FOR LEAKS.  
5
6
Move HANDLE down into "off" position.  
Turn on water supplies and check connections for leaks.  
Operate HANDLE (2) up and down, left and right to flush  
water lines thoroughly.  
Operate HAND SPRAY and check connections for leaks.  
CHECK CONNECTIONS  
FOR LEAKS  
SERVICE  
If faucet drips, operate HANDLE several times from "off" to "on." Do not  
apply excessive force.  
FLOW CONTROL DEVICE may accumulate dirt. To remove the FLOW CONTROL DEVICE,  
unthread SPRAY AND HOSE ASSEMBLY and rinse clean FLOW CONTROL DEVICE.  
3
4
2
Clogged CARTRIDGE outlets or inlets may cause reduced flow.  
To clean, first turn off water supply then:  
1
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).  
Unthread the ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).  
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE SEALS (8).  
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).  
Place SEALS (8) into CARTRIDGE PORTS (6A).  
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING  
SCREWS (5) alternately.  
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE  
SCREW (1) and install INDEX BUTTON (2).  
5
6
8
7
6A  
HOT LIMIT SAFETY STOP ADJUSTMENT  
By restricting handle rotation and limiting the amount of hot water allowed  
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental  
scalding. To set the maximum hot water temperature of your faucets, all you  
need to do is adjust the setting on the HOT LIMIT SAFETY STOP.  
Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull  
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade  
screwdriver or your fingers to pull up and rotate red HOT LIMIT  
FLOW CONTROL  
DEVISE  
SAFETY STOP (5). Follow Step "A" or "B" to adjust min./max.  
SPRAY AND HOSE  
discharge temperature. "0" being the hottest to "7" the coldest  
temperature setting. Factory set at "0".  
ASSEMBLY  
"A"  
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten  
HANDLE SCREW (1) and install INDEX BUTTON (2).  
PRY RED RING FORWARD  
AND ROTATE COUNTER-  
CLOCKWISE ONE CLICK  
"A"  
"A"  
TEMPERATURE  
SETTING NUMBERS  
ADJUSTMENT WHEN  
WATER IS TOO HOT  
"B"  
PRY RED RING FORWARD  
6
5
AND ROTATE CLOCKWISE  
"B"  
"B"  
ADJUSTMENT WHEN  
WATER IS TOO COLD  
"RED RING"- HOT  
LIMIT SAFETY STOP  
CARE:  
7
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.  
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A  
CLOTH WITH A COARSE SURFACE.  
M968986 Rev. 1.3  
 

Acer Computer Monitor UMHG6AAD02 User Manual
ACP EP Memory Camera Accessories EPMM 256 PLUS User Manual
Adaptec Computer Drive MAN FC2002 001 User Manual
Agilent Technologies Power Supply 66lxxA User Manual
Air King Fan 1VN45 User Manual
Allied Telesis Switch Rapier Switch User Manual
AMD Computer Hardware HD 2400 User Manual
American Dryer Corp Clothes Dryer AD 820 User Manual
American Standard Outdoor Shower 078016 0020A User Manual
Behringer Indoor Furnishings LD6230 User Manual