Adcom Surge Protector ACE 615 User Manual

Introduction  
The ACE-615 is a very carefully engineered product designed to protect  
your audio, video, and computer systems while providing them with clean  
AC power. The surge protection is a nonsacrificial patented technology  
(U.S. patents 4,870,534 and 4,870,528) that conforms to the strictest  
Federal Guidelines for surge protection.  
A C E - 6 1 5  
A
C
E
-
6
1
5
AC enhancer  
accessories  
amplifiers  
unswitched  
b
c
d
e
fb  
fa gb  
ga  
1@  
circuit breaker  
Surge Protector and AC Enhancer model ACE-615  
voltage: 120V AC/60Hz, internal power consumption: 10w max  
max 1500W  
B
coax 1  
coax 2  
12v trigger  
in  
max 300W  
accessories (switched 30 sec delay on turn-off)  
out  
in  
out  
in  
unswitched  
amplifiers (switched 10 sec delay on turn-on)  
E
out  
in  
15A  
GND  
phone 1  
phone 2  
serial #  
WARNING: For indoor use in dry locations only.  
To reduce the risk of shock, do not expose this unit  
to rain or moisture.  
WARNING: Equipment with high-current requirements, such as hobby arc-welders, hair  
dryers and heaters must not be plugged into these AC receptacles. Never allow total power  
consumption of all equipment connected to these outlets to exceed 1800 watts.  
10 Timber Lane  
Marlboro, NJ 07746 USA  
Made in the USA  
power 120v 60Hz  
max 1800W  
hb  
ib ia ha  
1#  
1$  
j
1)  
1!  
owner’s manual  
AC Enhancer  
 
Operation  
Front Panel Control  
indicating it is waiting for an external 12v trigger to power  
on. Turn on the component supplying the 12v trigger. The  
ACE-615 power button LED b and switched LED c and  
amplifiers LED d will glow red indicating AC power is  
being supplied to all connected components. Turn off  
the 12v trigger supply to return the ACE-615 to  
standby mode.  
Press the ACE-615 power button b to activate the unit.  
The power LED b, accessories LED c, and amplifiers  
LED d will glow red. AC power is being supplied to all  
connected components.  
The unswitched front panel LED e indicates that AC  
current is passing through the ACE-615 and into the  
components connected to the unswitched AC rear  
panel outlets 1). The unswitched LED e is always on  
provided the unit is plugged into an active AC source.  
To prevent turn-on thump, the jacks for the accessories  
and amplifiers have seperate relays. When the ACE-615 is  
turned on, the accessories power up before the amplifiers.  
When powering down, the relay works in reverse. These  
delays are in effect both with the 12V trigger source, and  
without, and the duration may be adjusted by your autho-  
rized ADCOM dealer.  
Remote 12v Trigger Control  
* Note: This section only applies when an external trigger is  
connected to the 12v trigger in jack 1@.  
* Note: The unit only responds to an external trigger when the  
power button b is pressed in. The power button b can  
be used to override the 12v trigger input and turn the  
ACE-615 off.  
Press the ACE-615 power button b to put the unit  
into standby mode. The power LED b will glow amber  
Typical Connections  
to device  
from wall  
circuit breaker  
Surge Protector and AC Enhancer model ACE-615  
voltage: 120V AC/60Hz, internal power consumption: 10w max  
B
coax 1  
coax 2  
12v trigger  
in  
max 300W  
max 1500W  
out  
in  
out  
in  
accessories (switched 30 sec delay on turn-off)  
unswitched  
amplifiers (switched 10 sec delay on turn-on)  
out  
in  
15A  
GND  
phone 1  
phone 2  
serial #  
WARNING: For indoor use in dry locations only.  
To reduce the risk of shock, do not expose this unit  
to rain or moisture.  
WARNING: Equipment with high-current requirements, such as hobby arc-welders, hair  
dryers and heaters must not be plugged into these AC receptacles. Never allow total power  
consumption of all equipment connected to these outlets to exceed 1800 watts.  
10 Timber Lane  
Marlboro, NJ 07746 USA  
Made in the USA  
power 120v 60Hz  
max 1800W  
 
Trouble shooting  
Symptom  
Possible Causes  
-Unswitched LED does not come on when the ACE-615 AC power cord is  
plugged into an outlet  
-Outlet may be shut off at the main breaker box  
-Power button pushed in, but switched outlets are off and power LED glows  
amber  
-Unit may be in standby mode  
-Remove any plug in the 12v trigger jack  
-ACE-615 does not respond to 12v input  
-Power button must be pressed in for remote activation  
-The trigger voltage maybe outside the allowable + (5-12) volts  
-
-No delay between accessories and amplifiers outlets  
-Delay settings are incorrect. Return to authorized dealer for adjustment.  
Factory settings are approximately ten seconds for amplifier turn-on and  
thirty seconds for accessories turn-off.  
Servicing  
Technical Specifications  
ADCOM has a technical service department to answer  
questions pertaining to the installation and operation of your  
unit. In the event of difficulty, please contact us for prompt  
advice. If your problem can not be resolved through our  
combined efforts, we may refer you to an authorized repair  
agency, or authorize return of the unit to the factory. To aid us  
in directing you to a convenient service station, please  
indicate which major city is accessible to your home.  
Electrical  
Input power..........................................120VAC, +/-10%, 5-/60Hz  
Protection.......................................................15A Circuit Breaker  
Internal Power Consumption.........................Less than 5 watts  
Control Input..................................................+/-5V to 24V AC/DC  
Total Output................................................................................15A  
Environmental: OperatingTemperature...............0 to +50 C  
StorageTemperature...............-40 to +80 C  
Filter  
Phone or Fax inquiries to:  
Phone (732) 683-2356  
Fax (732) 683-9790  
Mon - Fri 9AM - 5PM EST  
Noise: Normal Mode................-5dB at 5kHz; -38 dB at 300kHz  
Common Mode........-3dB at 300kHz; -40 dB at 1 MHz  
Surge Protection  
Endurance................................................1,000 surges 6 kV; 3 kA  
Clamping.............................................................................172 volts  
ResponseTime........................................................................0 sec.  
(Passive protection / always on)  
Maximum Applied Pulse (CombinationWave):  
Voltage: 6,000 volts  
Please direct inquiries to:  
ADCOM Service Department  
Please include a return phone or fax number for the reply.  
email and website info:  
Please include a return e-mail address for the reply.  
• Current: Unlimited due to current limiting  
• Joules: Unlimited due to current limiting  
Please address all mail inquires to:  
ADCOM Service Corporation  
10 Timber Lane  
Marlboro, NJ 07746 USA  
Please include a return address for the reply.  
Mechanical  
Dimensions....17”(430mm) x 12” (305mm) x 3.5”(89mm)  
Weight..........................................................................10 lbs. (2.7 kg)  
AC Cord............................................................................6 ft. (1.8m)  
 

3M Model Vehicle 78 8069 3983 7 User Manual
Acer Personal Computer G530 Series User Manual
Adrenaline Technologies Battery Charger IP1 User Manual
Agilent Technologies Network Router N9360A User Manual
AG Neovo Flat Panel Television ER 19 User Manual
Altec Lansing Laptop XT2 User Manual
Audiovox Car Stereo System CE1705 User Manual
Audiovox Remote Starter APS 410a User Manual
Bakers Pride Oven Oven CH 10J User Manual
Beckett Water Gardening Outdoor Fountain WFK16 User Manual