American Audio Turntable TTB 2010 User Manual

USER INSTRUCTIONS  
professional products designed for the working dj.  
 
User Instructions  
Assembly  
1. Remove the main unit with the packing from the box and take off the packing.  
2. Set the 45-rpm adapter on the main unit.  
3. Inset the turntable platter onto the center spindle.  
4. Set the slip mat on the platter.  
5. Installation of cartridge: When installing a cartridge, refer to the operating instructions of that cartridge.  
During installation, attach the stylus protector to guard the stylus tip from damage.  
(a) Connect the lead wires to the cartridge terminals. The terminals of most cartridges are color coded. Connect  
each lead wire to the terminal of the same color.  
WHITE (L+)..............Left channel+ BLUE (L-)..............Left channel-  
RED (R+)..............Right channel+ Green (R-)..............Right channel-  
(b) Install the cartridge to the headshell and tighten it with screws provided with the cartridge.  
6. Inset the headshell into the front end of the tonearm, then turn the lock nut counterclockwise clockwise with the  
headshell firmly held horizontally.  
7. Slide counterweight onto tonearm. Twist it lightly and it will screw onto the rear shaft of the tonearm.  
8. Adjustment of horizontal zero (0) balance and stylus pressure:  
(a) Remove the stylus protector, do not touch the stylus tip during the adjustment.  
(b) Set the cueing lever to the lower position.  
(c) Release the arm clamp and lift the tonearm from the arm rest to free it.  
(d) Rotate the counterweight until the tonearm is approximately balanced horizontally (floats freely).  
(e) Refasten the tonearm with the arm clamp.  
(f) Hold the counterweight stationary with one hand and rotate only the stylus-pressure ring to bring the number  
“o” of the ring into alignment with he center line on the tonearm rear shaft.  
(g) Rotate the counterweight counterclockwise until the scale shows the value corresponding to the pressure of the  
used stylus. The stylus pressure of the installed pick-up system is 2g. Should you use a separate pick-up  
system, please follow the manufacturer’s instruments.  
9. Set the anti-skating control knob to the same value as the stylus pressure.  
10. Install the dust cover to the main unit.  
Placement  
Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance.  
Do not place the unit in a location where there is high humidity or a lot of dust.  
Cartridge may pick up slight sound pressure or vibrations of the speakers coming along the floor or though the air  
resulting in howling. Find a location which is very stable and vibration free.  
The legs have functions for adjusting the height of the unit itself. Adjust the legs to stabilize the main body  
horizontally.  
Connections  
1. Connect the power cord to the auxiliary power outlet on the rear panel of your amplifier or receiver or to a household  
AC outlet.  
2. Connect the unit output terminals to the the PHONO jack of your American DJ Mixer or receiver.  
Output terminals  
Mixer (Receiver)  
L (White) (19) ---------------------------->L Channel  
R (Red) (18) -----------------------------> R Channel  
GND (Spade) (20) ---------------------> Ground  
NOTE: Be sure to connect the ground terminals firmly to the Mixer or receiver. If this connection is not made or is  
loose, a power source “HUM” will result.  
TTB-2010 User Instructions page 3  
 
User Instructions  
Operation  
1. Push the power button (4) to turn on the power, the speed indicator (8) and the strobe-illuminator will light up.  
2. Place a record on the slipmat. When playing a 45-rpm record with a large center hole, place the 45-rpm adapter (1)  
on the center spindle.  
3. Set the speed (10) to match the record.  
4. Remove the stylus protector, release the arm clamp.  
5. Set the cueing lever to the up position.  
6. Press the Start/Stop button (5), the turntable platter will start to rotate.  
7. Move the tonearm (13) over the desired groove.  
8. Set the cueing lever to the down position, the tonearm will descend slowly onto the record and begin playing.  
9. When play is finished, raise the cueing lever, move the tonearm with arm clasp.  
10.Press the Start/Stop Button (5) to stop the platter from rotating. Push the Power Button (4) to turn off the power.  
SUSPEND PLAY - Set the cueing lever to “UP” position during play, the stylus tip of the cartridge will be lifted  
from the record.  
TARGET LIGHT - This unit provides a target light (7) for illuminating the stylus tip during play. After pushing the  
target light button, the target light will be raised into position for illuminating the stylus tip. When not in use, keep  
the target light lowered.  
Changing the Speed  
As long as the pitch control (12) is in center click position, the turntable is operated at quartz controlled rated speed.  
The speed can be increased or decreased by 10% by the pitch control (12).  
An incorrect adjustment done on purpose can also be used to have the turntable rotate extremely slow or fast.  
The strobe dots (5) at the edge of the turntable are used for speed monitoring.  
Remote Control Start/Stop (21)  
The Start/Stop function can remotely be controlled by a separate switch via a mixing console with a “Fader Start”  
function. Activated the “Fader Start” on the mixing console and the turntable automatically begins Start/Stop.  
Future American DJ mixers will be equiped with the “Fader Start” function.  
Maintenance  
Clean the stylus periodically with a soft brush to prevent the accumulation of dust.  
When sound becomes distorted or noisy, check the stylus. If the stylus is worn out, replace it with a new one.  
From time to time, the dust cover and turntable cabinet should be wiped down with a soft, dry cloth.  
Volatile materials should not be used, such as: alcohol, thinner, benzine etc. They may remove the paint or  
damage the luster.  
Specifications  
Power Supply: AC 115V/60Hz, or 230V/50Hz  
Power Consumption: 8W  
Dimensions (WxDxH): 17.5” x 13 5/8” x 3.5 (6” high with dust cover) / 450mm x 350mm x 148mm  
Weight: 14 lbs./6.5kg.  
© American DJ® AUDIO  
4295 Charter Street  
Los Angeles, CA 90058 USA  
djs wanted.  
Specifications subject to change without notice. TTB-2010 User Instructions page 4  
 

Acnodes Computer Monitor APM5084 User Manual
ADC Network Router MMX 6000 User Manual
Aiphone Intercom System AN 8050DS User Manual
Aiwa Satellite Radio FR A308U User Manual
Aiwa Stereo System XR M70 User Manual
AKG Acoustics Microphone HT 40 PRO User Manual
Altinex Network Card MT106 103 User Manual
American Standard Indoor Furnishings M968663 User Manual
Atlas Indoor Furnishings MLG180B User Manual
BC Speakers Portable Speaker DE85 User Manual