User Manual
DIGITAL MONITOR SPEAKERS
MS /MS
24-Bit/192 kHz Digital 40/20-Watt Stereo Near Field Monitors
3
DIGITAL MONITOR SPEAKERS MS40/MS20 User Manual
9. Do not defeat the safety purpose of the polarized
UNDERTAKING OR REPRESENTATION. THIS MANUAL
IS COPYRIGHTED. NO PART OF THIS MANUAL MAY
BE REPRODUCED OR TRANSMITTED IN ANY FORM
OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,
Important Safety
Instructions
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the INCLUDING PHOTOCOPYING AND RECORDING OF ANY
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS
WRITTEN PERMISSION OF MUSIC GROUP IP LTD.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
ALL RIGHTS RESERVED.
© 2012 MUSIC Group IP Ltd.
Trident Chambers, Wickhams Cay, P.O. Box 146,
Road Town, Tortola, British Virgin Islands
Terminals marked with this symbol carry
electrical current of sufficient magnitude
to constitute risk of electric shock.
11. Use only attachments/accessories specified by
the manufacturer.
Use only high-quality professional speaker cables with
¼" TS or twist-locking plugs pre-installed. All other
installation or modification should be performed only
by qualified personnel.
12. Use only with the
cart, stand, tripod, bracket,
or table specified by the
LIMITED WARRANTY
§ 1 Warranty
manufacturer, or sold with (1) This limited warranty is valid only if you purchased
the apparatus. When a cart the product from a MUSIC Group Authorized Reseller in
This symbol, wherever it appears,
alerts you to the presence of uninsulated
dangerous voltage inside the
is used, use caution when
the country of purchase. A list of authorized resellers can
moving the cart/apparatus be found on BEHRINGER’s website behringer.com under
enclosure - voltage that may be sufficient to constitute a
risk of shock.
combination to avoid
“Where to Buy”, or you can contact the MUSIC Group office
closest to you.
injury from tip-over.
This symbol, wherever it appears,
alerts you to important operating and
maintenance instructions in the
13. Unplug this apparatus during lightning storms or
(2) MUSIC Group* warrants the mechanical and
when unused for long periods of time.
electronic components of this product to be free of defects
in material and workmanship if used under normal
operating conditions for a period of one (1) year from
the original date of purchase (see the Limited Warranty
terms in § 4 below), unless a longer minimum warranty
period is mandated by applicable local laws. If the product
shows any defects within the specified warranty period
and that defect is not excluded under § 4, MUSIC Group
shall, at its discretion, either replace or repair the product
using suitable new or reconditioned product or parts.
In case MUSIC Group decides to replace the entire product,
this limited warranty shall apply to the replacement
product for the remaining initial warranty period, i.e.,
one (1) year (or otherwise applicable minimum warranty
period) from the date of purchase of the original product.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
been dropped.
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, do not
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
qualified personnel.
Caution
To reduce the risk of fire or electric shock,
do not expose this appliance to rain and
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Caution
These service instructions are for use
by qualified service personnel only.
(3) Upon validation of the warranty claim, the repaired
or replacement product will be returned to the user
freight prepaid by MUSIC Group.
To reduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by qualified
service personnel.
(4) Warranty claims other than those indicated above
are expressly excluded.
PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF
OF PURCHASE COVERING YOUR LIMITED WARRANTY.
THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF
OF PURCHASE.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
LEGAL DISCLAIMER
TECHNICAL SPECIFICATIONS AND APPEARANCES
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND
ACCURACY IS NOT GUARANTEED. BEHRINGER IS
PART OF THE MUSIC GROUP (MUSIC-GROUP.COM).
ALL TRADEMARKS ARE THE PROPERTY OF THEIR
RESPECTIVE OWNERS. MUSIC GROUP ACCEPTS NO
LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED
BY ANY PERSON WHO RELIES EITHER WHOLLY OR
IN PART UPON ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN. COLORS AND
SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE SOLD THROUGH
AUTHORIZED FULLFILLERS AND RESELLERS ONLY.
FULLFILLERS AND RESELLERS ARE NOT AGENTS OF
MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY
TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED
§ 2 Online registration
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
Please do remember to register your new BEHRINGER
equipment right after your purchase at behringer.com
under“Support”and kindly read the terms and conditions
of our limited warranty carefully. Registering your
purchase and equipment with us helps us process
your repair claims quicker and more efficiently.
Thank you for your cooperation!
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
§ 3 Return materials authorization
(1) To obtain warranty service, please contact the
retailer from whom the equipment was purchased.
Should your MUSIC Group Authorized Reseller not be
located in your vicinity, you may contact the MUSIC Group
Authorized Fulfiller for your country listed under
4
DIGITAL MONITOR SPEAKERS MS40/MS20 User Manual
“Support”at behringer.com. If your country is not
listed, please check if your problem can be dealt with
by our“Online Support”which may also be found under
“Support”at behringer.com. Alternatively, please submit
an online warranty claim at behringer.com BEFORE
returning the product. All inquiries must be accompanied
by a description of the problem and the serial number
of the product. After verifying the product’s warranty
eligibility with the original sales receipt, MUSIC Group
will then issue a Return Materials Authorization
(“RMA”) number.
•
connection or operation of the unit in any way
that does not comply with the technical or safety
regulations applicable in the country where the
product is used;
(3) This warranty does not detract from the seller’s
obligations in regard to any lack of conformity of the
product and any hidden defect.
§ 9 Amendment
•
damage/defects caused by acts of God/Nature
(accident, fire, flood, etc) or any other condition that
is beyond the control of MUSIC Group.
Warranty service conditions are subject to change without
notice. For the latest warranty terms and conditions
and additional information regarding MUSIC Group’s
limited warranty, please see complete details online at
behringer.com.
(7) Any repair or opening of the unit carried out by
unauthorized personnel (user included) will void the
limited warranty.
* MUSIC Group Macao Commercial Offshore Limited of
Rue de Pequim No. 202-A, Macau Finance Centre 9/J, Macau,
including all MUSIC Group companies
(8) If an inspection of the product by MUSIC Group
shows that the defect in question is not covered by the
limited warranty, the inspection costs are payable by
the customer.
(2) Subsequently, the product must be returned in
its original shipping carton, together with the return
authorization number to the address indicated by
MUSIC Group.
(9) Products which do not meet the terms of this
limited warranty will be repaired exclusively at the buyer’s
expense. MUSIC Group or its authorized service center will
inform the buyer of any such circumstance. If the buyer
fails to submit a written repair order within 6 weeks after
notification, MUSIC Group will return the unit C.O.D. with
a separate invoice for freight and packing. Such costs will
also be invoiced separately when the buyer has sent in a
written repair order.
(3) Shipments without freight prepaid will not
be accepted.
§ 4 Warranty Exclusions
(1) This limited warranty does not cover consumable
parts including, but not limited to, fuses and batteries.
Where applicable, MUSIC Group warrants the valves or
meters contained in the product to be free from defects
in material and workmanship for a period of ninety (90)
days from date of purchase.
(10) MUSIC Group Authorized Resellers do not sell new
products directly in online auctions. Purchases made
through an online auction are on a“buyer beware”basis.
Online auction confirmations or sales receipts are not
accepted for warranty verification and MUSIC Group will
not repair or replace any product purchased through an
online auction.
(2) This limited warranty does not cover the product
if it has been electronically or mechanically modified
in any way. If the product needs to be modified or
adapted in order to comply with applicable technical
or safety standards on a national or local level, in any
country which is not the country for which the
product was originally developed and manufactured,
this modification/adaptation shall not be considered a
defect in materials or workmanship. This limited warranty
does not cover any such modification/adaptation,
regardless of whether it was carried out properly or not.
Under the terms of this limited warranty, MUSIC Group
shall not be held responsible for any cost resulting from
such a modification/adaptation.
§ 5 Warranty transferability
This limited warranty is extended exclusively to the
original buyer (customer of authorized reseller) and is
not transferable to anyone who may subsequently
purchase this product. No other person (reseller, etc.)
shall be entitled to give any warranty promise on behalf
of MUSIC Group.
(3) This limited warranty covers only the product
hardware. It does not cover technical assistance for
hardware or software usage and it does not cover
any software products whether or not contained in
the product. Any such software is provided“AS IS”
unless expressly provided for in any enclosed software
limited warranty.
§ 6 Claim for damage
Subject only to the operation of mandatory applicable
local laws, MUSIC Group shall have no liability to the buyer
under this warranty for any consequential or indirect
loss or damage of any kind. In no event shall the liability
of MUSIC Group under this limited warranty exceed the
invoiced value of the product.
(4) This limited warranty is invalid if the
factory-applied serial number has been altered or
removed from the product.
§ 7 Limitation of liability
This limited warranty is the complete and exclusive
warranty between you and MUSIC Group. It supersedes
all other written or oral communications related to this
product. MUSIC Group provides no other warranties for
this product.
(5) Free inspections and maintenance/repair work
are expressly excluded from this limited warranty,
in particular, if caused by improper handling of the
product by the user. This also applies to defects caused
by normal wear and tear, in particular, of faders,
crossfaders, potentiometers, keys/buttons, guitar strings,
illuminants and similar parts.
§ 8 Other warranty rights and
national law
(1) This limited warranty does not exclude or limit the
buyer’s statutory rights as a consumer in any way.
(6) Damage/defects caused by the following conditions
are not covered by this limited warranty:
(2) The limited warranty regulations mentioned herein
are applicable unless they constitute an infringement of
applicable mandatory local laws.
•
improper handling, neglect or failure to operate the
unit in compliance with the instructions given in
BEHRINGER user or service manuals;
5
DIGITAL MONITOR SPEAKERS MS40/MS20 User Manual
1. Introduction
BEHRINGER dealer not be located in your vicinity, you may directly contact
one of our subsidiaries. Corresponding contact information is included in the
original equipment packaging (Global Contact Information/European Contact
Information). Should your country not be listed, please contact the distributor
nearest you. A list of distributors can be found in the support area of our website
(http://behringer.com).
Two digital inputs plus two stereo analog inputs enable you to connect a
broad range of sound sources and mix two of them within the loudspeakers.
Additionally, we have equipped the MS20/MS40 with a headphone
connector. The speakers are magnetically shielded, so you can use them near
computer monitors.
Registering your purchase and equipment with us helps us process your repair
claims more quickly and efficiently.
◊
This User’s Manual is intended to familiarize you with the unit’s control
elements, so that you can master all the functions. After having
thoroughly read the user’s manual, store it at a safe place for
future reference.
Thank you for your cooperation!
1.1 Before getting started
2. Control Elements
and Connections
1.1.1 Shipment
Your MS20/MS40 speakers were carefully packed at the assembly plant to assure
secure transport. If the cardboard box is damaged, please inspect the equipment
immediately for any signs of physical damage.
◊
NEVER send damaged units directly to BEHRINGER.
Please, immediately notify the dealer from whom you acquired the
unit and the transportation company that delivered the unit to you.
Otherwise, all claims for replacement/repair may be rendered invalid.
(1) (2) (3)
(4)
(5)
(6)
(7)
◊
We recommend that you always use an appropriate carrying case
when transporting your MS20/MS40 speakers to ensure their
optimal protection.
Fig. 2.1: Front panel elements (right loudspeaker)
(1) Use the POWER switch to power up your MS20/MS40. The POWER switch
should always be in the “Off” position when you are about to connect your
unit to the mains.
◊
◊
◊
Always use the original packaging to avoid damage when shipping or
storing the unit.
◊
Please note: The POWER switch does not fully disconnect the unit from
the mains. To disconnect the unit from the mains, pull out the main
cord plug or appliance coupler. Unplug the power cord when the unit is
not used for prolonged periods of time.
Never let unsupervised children play with the MS20/MS40 or with
its packaging.
Please dispose of all packaging materials in an environmentally-
friendly fashion.
◊
Monitor speakers should be the last device in the signal chain to
be switched on and the first to be switched off. This way, you avoid
speaker damage caused by loud crackling noises during turning other
equipment in your studio on or off.
1.1.2 Initial operation
Please make sure the unit is provided with sufficient ventilation, and never place
the MS20/MS40 on top of an amplifier or in the vicinity of a heater to avoid the
risk of overheating.
(2) This LED lights up when power is switched on.
(3) Connect your headphones via the phones output (1" TRS) to monitor any
of the input devices. The internal speakers are automatically muted when
headphones are connected to the unit.
◊
Before plugging the unit into a power socket, please make sure that
the voltage corresponds to the voltage stated on the label on the
backside of your MS20/MS40.
(4) BASS control. Turn the bass control to adjust the bass level.
(5) TREBLE control. Turn the treble control to adjust the treble level.
Power is delivered via the cable enclosed with the unit. All required safety
precautions have been adhered to.
Turn the VOLUME controls (6) and (7) to adjust the overall volume levels of the
devices connected to your MS20/MS40:
Attention!
◊
These monitor speakers are capable of producing extreme volumes.
Please bear in mind that high sound pressures do not only temporarily
damage your sense of hearing, they can also cause permanent damage.
Be sure to select an appropriate volume level.
(6) The LINE 1 / DIGITAL knob controls the volume level of the analog LINE 1 (12)
or the DIGITAL inputs (8) or (9).
(7) Turn LINE 2 control to adjust the volume level of LINE 2 input (13).
◊
Attention: High volume levels may damage your hearing and/or your
headphones. Please turn the VOLUME controls all the way to the left
before powering up the unit. Be sure to always select an appropriate
volume level.
1.1.3 Online registration
Please register your new BEHRINGER equipment right after your purchase
warranty carefully.
Should your BEHRINGER product malfunction, it is our intention to have it
repaired as quickly as possible. To arrange for warranty service, please contact
the BEHRINGER retailer from whom the equipment was purchased. Should your
6
DIGITAL MONITOR SPEAKERS MS40/MS20 User Manual
3. Wiring
(8) (10) (9) (11)
The DIGITAL MONITOR SPEAKERS MS20/MS40 are designed to accommodate a
variety of connector types for almost any situation you may encounter.
You will find all audio inputs on the right speaker. The left speaker only has one
audio input which is fed from the right speaker.
◊
Be sure to mute the signal sources before you put the monitor speakers
into operation.
(12)
(13)
(14)
(15)
Fig. 2.2: Rear panel (right monitor)
(8) Digital audio data can be fed in at the OPTICAL input.
(9) The MS40 also features a digital COAXIAL input connector.
(10) With this switch you can select the digital input (OPTICAL or COAXIAL).
(11) SERIAL NUMBER.
(12) Analog input LINE 1 (1/8" TRS) allows you to connect stereo audio equipment
such as CD/MD players.
(13) Use the analog input LINE 2 (RCA) to connect your sound card,
keyboard or expander.
◊
You can play back various signals by using both stereo
inputs simultaneously.
(14) TO LEFT SPEAKER output connector. Connect both speakers by using the
speaker cable included in this package. As soon as both speakers are properly
connected, they will function as a stereo speaker system.
Fig. 3.1: Computer/keyboard setup
(15) A standard power socket is provided for connection to the mains. A matching Begin by connecting the left speaker to the right speaker by wiring the attached
power cable is included with the unit. Before you connect the unit to the
power source make sure that the power switch is turned off and the volume
controls are turned all the way to the left to avoid any damage to speakers or
other devices.
speaker cable from connector (14) to connector (16) on the left speaker.
Connect the analog outputs of your mixer, keyboard or computer sound card to
LINE 1 input (12). Connect a second piece of equipment to LINE 2 inputs (13).
If you own equipment with digital connectors—such as CD or MD players—
simply connect them to the digital inputs (8) and (9). Select the digital signal
you want to monitor with the input selector switch (10).
You can mix two input signals within the MS20/MS40 by using the volume
controls (6) and (7). This enables you to monitor two different sound sources
simultaneously. The above wiring example shows how you can monitor your live
keyboard performance to a playback coming from your MD player or digital audio
workstation (computer).
(16)
The MS20/MS40 speakers are shielded, which allows you to place them near your
computer monitor without causing interference or damage. However, do not
place your MS20/MS40 speakers near power amps. Doing so will result in an
induced hum in your speakers.
Fig. 2.3: Rear panel (left monitor)
(16) FROM RIGHT SPEAKER connector. Insert the speaker cable from the
TO LEFT SPEAKER connector.
7
DIGITAL MONITOR SPEAKERS MS40/MS20 User Manual
4. Specifications
Loudspeakers
Physical
MS40
MS40
Tweeter
Ø 65 mm (2 1"), 8 Ω
Ø 120 mm (4 3"), 4 Ω
Dimensions (H x W x D)
11 x 6 4/5 x 9 5/8"
279 x 173 x 245 mm
Woofer
Weight
MS20
17.71 lbs/8.05 kg
MS20
Tweeter
Woofer
Ø 65 mm (2 1"), 8 Ω
Ø 92 mm (3 5/8"), 4 Ω
Dimensions (H x W x D)
9 2/5 x 6 x 7 3/8"
239 x 154 x 187 mm
Weight
12.83 lbs/5.83 kg
Audio Inputs
Line 1
Line 2
1/8" TRS stereo, impedance 20 kΩ
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts,
modifications may be made from time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or illustrated.
2 RCA, impedance 20 kΩ
Digital Inputs
Optical
TOSLINK
RCA
Coaxial
Converter
Sample rate
24-bit
< 192 kHz
System Specifications
MS40
Output power
2 x 20 W
Frequency response
50 Hz to 25 kHz
MS20
Output power
2 x 10 W
Frequency response
65 Hz to 25 kHz
Power Supply
Mains Voltages
USA/Canada
Europe/U.K./Australia
China
120 V~, 60 Hz
230 V~, 50 Hz
220 V~, 50 Hz
Japan
100 V~, 50 - 60 Hz
120/230 V~, 50 - 60 Hz
General export model
Power Consumption
MS40:
90 W
MS20:
80 W
9
DIGITAL MONITOR SPEAKERS MS40/MS20 User Manual
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
DIGITAL MONITOR SPEAKERS
MS40/MS20
Responsible Party Name:
Address:
MUSIC Group Services US Inc.
18912 North Creek Parkway,
Suite 200 Bothell, WA 98011,
USA
Phone/Fax No.:
Phone: +1 425 672 0816
Fax: +1 425 673 7647
DIGITAL MONITOR SPEAKERS MS40/MS20
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC Group
can void the user’s authority to use the equipment.
We Hear You
|