Baby Trend Baby Furniture 8136BCC User Manual

Read all instructions BEFORE assembly and USE of product.  
KEEP INSTRUCTIONS FOR FUTURE USE.  
Model #8136BCC  
DELUXE TREND NURSERY CENTER  
Instruction Manual  
Convenience through Innovation and thoughtful design  
12.04  
 
FOR THE SAFETY OF YOUR CHILD, PLEASE READ THE INSTRUCTIONS COMPLETELY  
BEFORE ASSEMBLING THE PLAYARD, BASSINET AND CHANGING AREA  
TO ASSEMBLE PLAYARD  
CONTENTS (Fig. 1-1):  
1 Playard  
1 Mattress  
1 Organizer  
2 Leg extensions (1 Left,1 Right)  
2 Leg extensions with wheels (1 Left, 1 Right)  
1 Travel or Storage bag  
Figure 1-1.  
BEFORE YOU BEGIN: The Baby Trend Playard is designed so that,  
when properly setup, the fabric of the playard places pressure on the 4  
top rails making them nearly impossible to unlock. This safety feature  
is activated when you push down on the playard floor to lock the bottom  
rails. When setting up the playard, if you allow the bottom rails to lock  
Figure 1.  
before locking the top rails, the fabric pressure will not allow you to lock  
the top rails. Please see (Fig. 3.) for the proper position of the bottom of  
the playard when locking the top rails.  
1. Unzip bag and remove Playard frame (Fig. 1). Undo the 3 Velcro straps  
and set mattress aside (Fig. 2).  
2. Turn the playard upside down. (Fig. 3). Push each leg extension into  
the bottom of the leg until both sides of extension snap into place. (Fig.  
Figure 2.  
4). Check that the extension is firmly connected. Attach the wheels to  
the playard with the axle and nut as shown in figure (Fig. 5). The brake  
cluster on the wheel must face to the inside. The axle is inserted from  
the outside to the inside. (Fig. 6). Check that the wheels are firmly  
connected.  
Leg extensions  
3. Stand Playard on legs keeping feet of playard close together as shown in  
(Fig. 7). Pull up on top rails until all rails “click” and “lock”.  
* READ IMPORTANT: In order to continue, the handle in the center  
of the floor of the Playard MUST remain raised in order for the  
rail to lock (approx. 45.7 cm or 18 inches). The feet of the playard  
should almost touch each other. All 4 bottom rails must be pointed  
upward in order to LOCK top rails.  
4. Push down on center of Playard floor until it is flat and locks into  
position (Fig. 8). The center lock mechanism will lock automatically.  
The center lock will rotate clockwise about 90 degrees as it locks.  
Wheels  
NOTE: Test rails to make sure they are locked. Push down on each  
rail making sure they are rigid and in a set position.  
Figure 3  
3
 
WARNING: All top rails MUST be  
straight and locked in position or child may  
become entrapped and suffocate.  
See figure 9 and 10.  
5. Place mattress in Playard with padded side up (Fig. 11).  
NOTE: DO NOT insert mattress if using bassinet feature. Go to  
bassinet instructions.  
Figure 5  
Right  
Left  
6. Feed the 6 Velcro straps (found underneath the mattress), 3 on each  
end of the mattress pad, through the slots on the bottom of the sides  
of the Playard. Fasten the Velcro tabs to the underside of Playard to  
prevent the mattress from moving (Fig. 12) (Fig. 13).  
Insert  
Insert  
axle from  
outside  
axle from  
outside  
WARNING: To prevent child from  
suffocating, Velcro straps MUST be secured  
to underside of Playard.  
Left  
Figure 5  
Right  
7. Attach the organizer, to any side of the playard, by pushing the plastic  
clips down over the top rail. (Fig. 14). The maximum weight capacity  
of the organizer is 3 pounds.  
8. To operate the brakes on the wheels, press downward on the brake  
lever as shown in figure 15. To release, lift upward on the lever.  
Playard assembly is now complete and ready to use.  
Outside  
Inside  
Figure 6  
Figure 9  
Figure 7  
Figure 8  
Figure 10  
Figure 11  
Figure 12  
Figure 13  
Figure 14  
Figure 15  
4
 
FOLDING PLAYARD  
1. Undo the 6 Velcro straps holding mattress from underneath Playard  
floor. (If mattress is not used in the bassinet). Remove mattress and set  
aside.  
2. Grasp the center floor lock handle pushing down . Rotate the handle  
counter-clockwise about 90 degrees and lift upward until handle is as  
high as the top rails. Gather the four feet of the playard together so that  
they nearly touch each other. See figure 1 and 2.  
Rotate before  
lifiting  
Figure 1  
NOTE: TOP RAILS OF THE PLAYARD ARE STILL IN THE  
“LOCKED” POSITION.  
3. Locate release button on the center of the bottom of each top rail. Lift  
slightly while squeezing button until the rail clicks. Push down on rail  
(while still holding release button in) until side forms a “U”. Repeat for  
remaining sides (Fig. 3).  
NOTE: If top rail(s) do not form the “U” completely do not force. Check  
the floor of your Playard to make sure all bottom rails are unlocked and  
pull up on middle handle of floor again. Repeat  
step 3.  
Figure 2  
4. Pull up on handle in center of Playard (Fig. 4). Gather legs of Playard  
together.  
5. Wrap mattress around Playard frame with padded side facing in.  
6. Secure the 3 Velcro straps by feeding through loops on end of mattress  
and folding back onto itself (Fig. 5).  
7. Place Playard in carry bag so handle comes through opening between  
zippers and wheels come through opening in the end of bag.  
Figure 3  
WARNING: NEVER LEAVE INFANT IN  
PRODUCT WITH SIDES DOWN.  
Infant may roll into space between  
pad and loose mesh side causing  
suffocation.  
Figure 5  
Figure 4  
5
 
PLAYARD BASSINET/CHANGING AREA  
12.04  
WARNING:FAILURE TO FOLLOW THESE WARNINGS  
AND THE ASSEMBLY INSTRUCTIONS COULD RESULT  
IN SERIOUS INJURY OR DEATH FROM ENTRAPMENT,  
STRANGULATION, SUFFOCATION, ETC.  
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their back  
to sleep, unless otherwise advised by your physician.  
Always provide the supervision necessary for the continued safety of your child. When used  
for playing, never leave child unattended.  
Adult supervision is always necessary when using your bassinet.  
Your playard, including side rails and bottom pad, must be fully erected prior to use.  
Top rails must be locked.  
Bottom rails must be in flat, locked position.  
SUFFOCATION HAZARD: To help prevent suffocation from entrapment, use only the  
mattress provided by BabyTrend®. Neveruse additional mattress orpadding. Neveruse plastic  
shipping bags or other plastic film as mattress covers not sold and intended for that purpose.  
Avoid SUFFOCATION HAZARD caused by a loose sheet. A fitted sheet is recommended. The  
fitted sheet must fit the mattress tightly.  
STRANGULATION HAZARD: DO NOT place items with a string around child’s neck, such  
as hood strings or pacifier cords. DO NOT suspend string over bassinet or attach strings to  
toys.  
DO NOT add padding or other objects inside your bassinet which will permit a child to climb  
out.  
To prevent your child from falling out of the bassinet discontinue using your bassinet when  
your child is too active, able to climb out, weighs over 15 lbs.. (6.8 kgs.), or is over 4 months  
old.  
DO NOT use a water mattress with this bassinet.  
Use your bassinet with only one child at a time.  
Keep bassinet away from stoves, heaters, campfires and other hazards.  
Never place a child under the bassinet.  
DO NOT store the bassinet in the playard.  
The bassinet must be fully assembled and installed, including top rails and bottom pad,  
before using.  
Before each use or assembly, inspect the playard and bassinet / changing area for damaged  
hardware, loose joints, missing parts or sharp edges. DO NOT use playard or bassinet if  
any parts are missing or broken. Call our Customer Service department at (800) 328-7363 for  
replacement parts.  
To protect your child from falls and other injuries: always use safety belt when child is on the  
changing table, always stay within arm’s reach of your child when using the changing table,  
never leave child unattended.  
Baby Trend, Inc.  
1567 S. Campus Ave.  
Ontario, CA 91761  
Customer Service Hot Line:  
(800) 328-7363  
8:00 A.M. to 4:30 P.M. Pacific Standard Time  
6
 
TO ASSEMBLE YOUR BASSINET  
NOTE: Playard MUST be in a locked set-up position before  
installing and using the bassinet feature.  
CONTENTS (Fig. 1):  
2 Right corner supports  
2 Left corner supports  
1 Nylon bassinet insert  
2 Long metal tubes  
2 Medium metal tubes  
2 Short metal tubes  
ASSEMBLY  
Figure 1  
Figure 2  
1. Insert 1 short tube into a medium tube lining up the snap button and  
the hole opening. Make sure the snap buttons are exactly fitted into  
the holes (Fig. 2). Repeat for the second set of tubes.  
2. Unroll the nylon bassinet fabric. Insert one set of the connected  
tubes into each long side of the bassinet sleeve (Fig. 3).  
NOTE: The printed warning label should be facing toward the  
inside of the bassinet and is readable.  
3. Insert 1 long tube into the short side of the bassinet sleeve. Repeat  
for remaining side.  
4. Slide the corner supports onto the ends of each tube (Fig. 4). The  
corner support with a hole is used for the mobile. Place this corner  
support on the end opposite the changing table.  
The bassinet canopy is secured to the bassinet with snaps on the  
outside sleeve. Snap both on the ends of the canopy to the sleeve as  
shown in (Fig. 4a). The rear section of the canopy is connected to  
the bassinet sleeve as shown in (Fig. 4b).  
Figure 3.  
5. Place assembled bassinet onto the Playard. Push down each of the  
corner supports (Fig. 5).  
NOTE: The corner supports are designed to rest on long side of  
Playard (40 in. rail) and wrap around the short side of the Playard  
top corner pieces.  
Figure 4.  
6. Place the Playard mattress into the bassinet with the padded side  
facing up (Fig. 6).  
bassinet  
snap  
Figure 5.  
Figure 6.  
Figure 4a.  
Figure 4b.  
7
 
TO ASSEMBLE CHANGING AREA  
CONTENTS (Fig. 1):  
2 Long curved bars  
2 Short bars with connector knobs  
1 Changing area fabric  
Figure 1  
WARNING:  
Avoid serious injury or death:  
Always use restraint belt to prevent falls (Fig.  
1-1).  
• Use changer with infant who’s weight is less  
than 18 lbs (8.2 kg ) and is less than  
25 inches (63.5 cm) tall.  
Figure 2  
• Discontinue use of changer if infant can push  
up on hands and knees or sit unassisted.  
DO NOT carry changer with infant in it.  
WARNING: Strangulation Hazard  
Child can lift the changing table and get  
neck trapped between the changing table  
frame and the play yard frame. Never leave  
the changing table in place when the child is  
in the bassinet or the play yard. Always flip  
changer to the outside when not in use.  
Holes face  
down  
Figure 3  
ASSEMBLY  
Figure 4.  
1. Connect the two Long Curved Bars together as shown in figure 2.  
2. Insert the assembled Curved Bars into the Changing Area Fabric  
such that the holes in the ends of the Curved Bars face downward  
as shown in Figure 3.  
3. Slide the Curved Bars around inside the sleeve of the Changing  
Area Fabric.  
4. Connect the Short Bars with Connector Knobs to the Curved  
Bars as shown in figure 4. When assembling the Short Bars with  
Connector Knobs make sure that the knobs will be facing inward  
when assembled and the snap buttons are facing downward.  
Completed assembly  
Figure 5.  
8
 
NOTE: Short bar with connector knobs should be facing  
inward.  
5. Place connector knob prongs into holes located on corner pieces  
of Playard (Fig. 5).  
6. Turn connector knobs counter clockwise to lock (Fig. 6).  
7. Flip changing area to inside of Playard (Fig.7).  
8. Snap flap from changing area to side of Playard (Fig. 8).  
9 Check that changing area is secure before using.  
Figure 5.  
Figure 6.  
Figure 7.  
Figure 8.  
REMOVALAND FOLDING CHANGING AREA  
ASSEMBLY  
1. Flip changing area to the outside of the Playard. Unsnap fabric flap  
of changing area from Playard.  
2. Twist connector knobs clockwise to unlock (Fig. 1).  
3. Remove changing area from Playard (Fig. 2).  
4. Disconnect the short bars from the curved bar by pressing on the  
snap buttons and pulling apart. Remove curved bar from changing  
area sleeve.  
Figure 1.  
The changing area is now ready for storage.  
Figure 2.  
9
 
REMOVAL OF BASSINET  
ASSEMBLY  
1. Remove mattress from bassinet (Fig.1).  
2. Lift bassinet out of Playard (Fig. 2).  
3. Remove corner pieces and slide metal tubes from fabric sleeves  
(Fig. 3).  
4. Separate tubes by pressing on snap buttons and pull apart.  
The bassinet is now ready for storage.  
NOTE: Store bassinet and changing area with folded Play yard  
in carry bag.  
Figure 1  
Figure 3  
Figure 2  
TO REMOVE CANOPY  
REMOVAL OF CANOPY  
To remove the bassinet canopy, unsnap the ends of the canopy from  
the side of the bassinet. The canopy can be stored in the travel bag.  
STOP  
IF YOU EXPERIENCE ANY DIFFICULTY IN USING THIS PRODUCT, PLEASE  
CONTACT OUR CUSTOMER SERVICE DEPARTMENT AT (800) 328-7363 BETWEEN  
THE HOURS OF 8:00 A.M. AND 4:30 P.M. PACIFIC COAST TIME FOR ASSISTANCE.  
10  
 
 

2Wirer HDCR 1230G User Manual
AC International Styling Iron AC8PROS User Manual
AEG Microwave Oven EMS26415X User Manual
Agilent Technologies Power Supply PN 8510 16 User Manual
Aiphone Home Security System C 123l A User Manual
Audiovox Remote Starter AS 9256 User Manual
Axis Communications Security Camera AVTPSC User Manual
Baldor Baby Accessories iMN1921 User Manual
Behringer Music Mixer PMP518M User Manual
Beko Flat Panel Television F 772 GRI User Manual