Avital Universal Remote 5303 User Manual

Model 5303  
Owner’s Guide  
 
ING, REPAIR, REPLACEMENT, DAMAGES FOR LOSS OF TIME, LOSS OF  
EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY  
AND THE LIKE. NOTWITHSTANDING THE ABOVE, MANUFACTURER  
DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON-  
TROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on  
how long an implied warranty will last or the exclusion or limitation of incidental or con-  
sequential damages. This warranty gives you specific legal rights, and you may also have  
other rights which vary from state to state.  
Make sure you have all of the following information from your dealer:  
A clear copy of the sales receipt, showing the following:  
Date of purchase  
Your full name and address  
Authorized dealer's company name and address  
Type of alarm installed  
Year, make, model and color of the automobile  
Automobile license number  
Vehicle identification number  
All security options installed on automobile  
Installation receipts  
©
2008 Directed Electronics—All rights reserved  
ii  
 
Table of contents  
Limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i  
Standard transmitter configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
What is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
System maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Your warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Fcc/id notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Caution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Transmitter functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Using your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Warning! Safety first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Active arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Passive arming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Multi-level security arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Arming while driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Disarming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
High security disarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Disarming without a transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Silent mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Panic mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Remote start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Rear defogger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Valet take-over. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Short-run/turbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Starter anti-grind circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Disabling the remote start system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Shut down inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Nuisance prevention® circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Arming diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Disarming diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
System status chirps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Table of zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Interpreting zone diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Code hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
High frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
Owner recognition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
©
2008 Directed Electronics—All rights reserved  
1
 
Rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
Glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Quick reference guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
©
2008 Directed Electronics—All rights reserved  
2
 
Standard transmitter configuration  
controls the Arm and Panic On/Off function.  
controls the Disarm and Panic Off function.  
controls Silent Mode™ and Auxiliary trunk output.  
controls the Remote Start function.  
and  
and  
and  
and  
and  
pressed together control the Timer mode.  
pressed together control Turbo/Short Run.  
pressed together control auxillary 4 output.  
pressed together control auxillary 5 output.  
and  
pressed together control the rear  
defogger.  
and  
pressed together control auxillary 6 output.  
3
©
2008 Directed Electronics—All rights reserved  
 
and  
and  
and  
and  
control Temperature check.  
controls Daily start on/off.  
and  
controls Temperature start on/off.  
What is included  
A control module  
A transceiver/antenna  
Two four-button transmitters  
®
A Stinger™ DoubleGuard two-stage shock sensor  
A Revenger™ Soft Chirp™ six-tone programmable siren  
A status LED indicator light  
A push-button Valet button  
Your warranty registration  
A shut-down toggle switch  
Important information  
Congratulations on the purchase of your combination remote  
start alarm system. Due to the complexity of this system, it must  
be installed by an authorized dealer only. Installation of this  
product by anyone other than an authorized dealer voids the  
©
2008 Directed Electronics—All rights reserved  
4
 
warranty. All dealers are provided with a preprinted dealer certif-  
icate to verify authorization.  
By carefully reading this Owner's Guide prior to using your  
system, you will maximize the use of this system and its features.  
You can print additional or replacement copies of this manual by  
System maintenance  
The system requires no specific maintenance beyond remote  
battery replacement. The remote is powered by a 1.5V AAA  
battery.  
The battery level indicator has three level indicators that serve as  
a visual indication of battery charge. When the battery reaches a  
low charge level that requires replacment, the remote generates  
a single notification chirp, and the battery level indicator flashes  
continuously.  
Battery Replacement  
Gently pull the battery cover release tab, thenslide the door  
down to expose the baattery and remove the expired battery.  
Place the new battery into the remote observing the correct  
polarity. When power is returned the remote lights all icons in  
the LCD and gnerates all beeper tones at once.  
5
©
2008 Directed Electronics—All rights reserved  
 
Your warranty  
Your warranty registration must be completely filled out and  
returned within 10 days of purchase. Your product warranty  
will not be validated if your warranty registration is not returned.  
Make sure you receive the warranty registration from your dealer.  
It is also necessary to keep your proof of purchase, which reflects  
that the product was installed by an authorized dealer.  
Fcc/id notice  
This device complies with Part 15 of FCC rules. Operation is  
subject to the following two conditions: (1) This device may not  
cause harmful interference, and (2) This device must accept any  
interference received, including interference that may cause  
undesirable operation.  
Changes or modifications not expressly approved by the party  
responsible for compliance could void the user's authority to  
operate this device.  
Caution  
This product is designed for fuel injected, automatic transmis-  
sion vehicles only. Use of this product in a standard transmission  
vehicle is dangerous and contrary the product's intended use.  
©
2008 Directed Electronics—All rights reserved  
6
 
Transmitter functions  
The receiver uses a computer-based Learn Routine to learn the  
transmitter buttons. This makes it possible to assign any remote  
transmitter button to any receiver function. The transmitter  
initially comes programmed with Standard Configuration, but  
may also be customized by an authorized dealer. The buttons in  
all of the instructions in this manual correspond to a Standard  
Configuration transmitter.  
Standard configuration  
Button  
The arming and panic functions are controlled by pressing this  
button for one second.  
Button  
The disarming function is controlled by pressing this button for  
one second.  
Button  
Silent Mode™ and an optional auxiliary function are controlled  
by this button. (Silent Mode works by pressing this button for  
less than one second before arming or disarming. An optional  
auxiliary function, such as trunk release, can be controlled by  
pressing this button for 1.5 seconds.)  
The auxiliary output controls __________________________.  
Button  
7
©
2008 Directed Electronics—All rights reserved  
 
The remote start function of your system is controlled by  
pressing this button twice within 3 seconds.  
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
The auxiliary output controls __________________________.  
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
The auxiliary output controls __________________________.  
and  
Buttons  
The remote start timer mode is controlled by pressing these  
buttons simultaneously. The 2-way remote produces a melody  
and the clock indicator appears on the remote's LCD. Once in  
timer mode the system remote starts every 24-hours. Repeat this  
procedure to turn Timer Mode off.  
and  
Buttons  
The short-run turbo mode is activated when these buttons are  
pressed simultaneously.  
and  
and  
Buttons  
When simultaneously pressed these buttons control the rear  
window defogger during remote starting.  
©
2008 Directed Electronics—All rights reserved  
8
 
and  
Buttons  
An optional auxiliary convenience or expansion function that  
you have added to your system can be activated by pressing these  
buttons simultaneously.  
The auxiliary output controls __________________________.  
and  
and  
This system reports the interior temperature of your vehicle by  
pressing these buttons sequentially.To activate the temperature  
display press the above three buttons. You hear a melody and the  
interior temperature is displayed on the LCD screen for five  
seconds.  
Note: If the ignition is on, the temperature check  
clockmode will not work.  
and  
Buttons  
While the system is armed, press simulataneously to enter  
temperature auto statt mode. The vehicle is automatically  
restarted if the interior temperature drops below 0 degrees  
Fahrenheit.  
Note: Disarming the system while in temperature  
autostart mode casuses the system to exit this mode.  
©
2008 Directed Electronics—All rights reserved  
9
 
Using your system  
Warning! Safety first  
The following safety warnings must be observed at all times:  
Due to the complexity of this system, installation of this  
product must only be performed by an authorized Directed  
dealer.  
When properly installed, this system can start the vehicle via  
a command signal from the remote control transmitter.  
Therefore, never operate the system in an enclosed area or  
partially enclosed area without ventilation (such as a garage).  
When parking in an enclosed or partially enclosed area or  
when having the vehicle serviced, the remote start system  
must be disabled using the installed toggle switch. It is the  
user's sole responsibility to properly handle and keep out of  
reach from children all remote control transmitters to assure  
that the system does not unintentionally remote start the  
vehicle. THE USER MUST INSTALL A CARBON  
MONOXIDE DETECTOR IN OR ABOUT THE  
LIVING AREA ADJACENT TO THE VEHICLE. ALL  
DOORS LEADING FROM ADJACENT LIVING AREAS  
TO THE ENCLOSED OR PARTIALLY ENCLOSED  
VEHICLE STORAGE AREA MUST AT ALL TIMES  
REMAIN CLOSED. These precautions are the sole respon-  
sibility of the user.  
Use of this product in a manner contrary to its intended  
©
2008 Directed Electronics—All rights reserved  
10  
 
mode of operation may result in property damage, personal  
injury, or death. (1) Never remotely start the vehicle with the  
vehicle in gear, and (2) Never remotely start the vehicle with  
the keys in the ignition. The user must also have the neutral  
safety feature of the vehicle periodically checked, wherein the  
vehicle must not remotely start while the car is in gear. This  
testing should be performed by an authorized Directed dealer  
in accordance with the Safety Check outlined in the product  
installation guide. If the vehicle starts in gear, cease remote  
start operation immediately and consult with the authorized  
Directed dealer to fix the problem.  
After the remote start module has been installed, contact  
your authorized dealer to have him or her test the remote  
start module by performing the Safety Check outlined in the  
product installation guide. If the vehicle starts when  
performing the Neutral Safety Shutdown Circuit test, the  
remote start unit has not been properly installed. The remote  
start module must be removed or the installer must properly  
reinstall the remote start system so that the vehicle does not  
start in gear. All installations must be performed by an autho-  
rized Directed dealer. OPERATION OF THE REMOTE  
START MODULE IF THE VEHICLE STARTS IN GEAR  
IS CONTRARY TO ITS INTENDED MODE OF OPER-  
ATION. OPERATING THE REMOTE START SYSTEM  
UNDER THESE CONDITIONS MAY RESULT IN  
PROPERTY DAMAGE OR PERSONAL INJURY. YOU  
MUST IMMEDIATELY CEASE THE USE OF THE  
©
2008 Directed Electronics—All rights reserved  
11  
 
UNIT AND SEEK THE ASSISTANCE OF AN AUTHO-  
RIZED DIRECTED DEALER TO REPAIR OR  
DISCONNECT THE INSTALLED REMOTE START  
MODULE. DIRECTED WILL NOT BE HELD  
RESPONSIBLE OR PAY FOR INSTALLATION OR  
REINSTALLATION COSTS.  
Active arming  
You can arm the system by pressing  
of your transmitter for  
one second. When the system arms, you will hear a short siren  
sound, or chirp, and see the parking lights flash once. If the power  
door locks are controlled by the system, the doors will also lock.  
While the system is armed, the status LED will flash approxi-  
mately once per second, indicating that the system is actively pro-  
tecting your vehicle. If you hear a second chirp after arming and  
note that the status LED is flashing in groups, see the Diagnostics  
Section of this guide. This extra chirp is called Bypass Notification.  
Passive arming  
The system can be programmed to arm itself automatically (called  
passive arming). If the system is programmed for passive arming, it  
will automatically arm 30 seconds after the ignition is turned off  
and the system detects that you have left the vehicle by opening and  
closing a door. Whenever the system is in its 30-second passive  
arming countdown, the status LED will flash twice as fast as it does  
when the system is armed. At the 20-second point of the count-  
down, the siren will chirp to indicate that the system is about to  
arm. At the 30-second point, the parking lights will flash to indicate  
©
2008 Directed Electronics—All rights reserved  
12  
 
that the system is armed.  
Note: If any protected entry point (such as a door or a  
switch-protected trunk or hood) is open, the system will  
not passively arm (unless forced passive arming is pro-  
grammed on. See Programming Options section).  
When armed your vehicle is protected as follows:  
®
Light impacts trigger the Warn Away signal. When trig-  
gered, the siren chirps and the parking lights flash for a few  
seconds.  
Heavy impacts trip a Triggered Sequence. The sequence  
consists of the siren sounding continuously and the parking  
lights flashing for a pre-programmed period, which can range  
in duration from 1 to 180 seconds.  
If a door is opened, the system will immediately start  
chirping the siren and flashing the parking lights. Three  
seconds later, the siren output changes to a continuous blast.  
This progressive response gives you time to disarm the system  
with your transmitter if you inadvertently open the door  
while the system is armed, while still providing instant re-  
sponse (even if the door is immediately closed).  
Turning on the ignition key will trip the same progressive re-  
sponse as opening a door.  
The optional starter kill prevents the vehicle’s starter from  
cranking.  
Multi-level security arming  
Multi-Level Security Arming allows you to select which of the  
system's inputs or sensors will be active and which will be  
13  
©
2008 Directed Electronics—All rights reserved  
 
bypassed when the system is armed. (See Table of Zones section of  
this guide.) Pressing (only in Standard Configuration) again  
within five seconds of arming the system will activate the Multi-  
Level Security feature. Each time is pressed again, a different  
security level is selected. The different security levels are selected  
as follows:  
Press  
Press  
once: The siren chirps once. The system is armed.  
a second time within five seconds: The siren chirps  
twice followed by a long chirp. Zone 2 is now bypassed.  
Press a third time within five seconds: The siren chirps  
three times followed by a long chirp. Zone 4 is now bypassed.  
Press a fourth time within five seconds: The siren chirps four  
times followed by a long chirp. Zones 2 and 4 are now bypassed.  
Press a fifth time within five seconds: The siren chirps  
five times followed by a long chirp. All input zones, except  
the ignition, are now bypassed.  
Note: Multi-Level Security Arming only applies to a sin-  
gle arming cycle. Once the system is disarmed and then  
re-armed, all the zones will be active again.  
Arming while driving  
Your security system can be armed while driving the vehicle!  
Simply press  
on the transmitter for two seconds while the  
vehicle is running. The siren will chirp once to indicate that the  
security system is armed, and then once more to indicate that the  
ignition is on. The system will not respond to any input except  
©
2008 Directed Electronics—All rights reserved  
14  
 
the door triggers, and the starter kill relay (if installed) will not  
be activated. Once you have arrived at your destination, the  
system will disarm when the ignition is turned off. The siren will  
chirp twice and the LED will then stop flashing. The system can  
also be disarmed at any time by pressing  
.
Disarming  
To disarm the security system, press  
. You will hear two  
chirps, and the parking lights will flash twice. If the power locks  
are controlled by the system, the doors will also unlock. The  
siren chirping either four or five times when disarming indicates  
Tamper Alert, which is described in the Diagnostics Section of  
this guide.  
High security disarm  
This security system offers High Security Disarm. High Security  
Disarm is a feature that makes it possible to silence and reset the  
system while it is triggering, without disarming the system. If the  
system is triggered and the siren has been sounding for longer  
than six seconds, pressing  
on the remote transmitter will  
stop the trigger and return the unit to the armed state. The  
system will not disarm, but rather reset. This prevents you from  
disabling the system should you wish to disarm it without visu-  
ally checking the vehicle. Pressing  
after resetting the system  
will disarm the system; pressing this button during the first six  
seconds of the triggered sequence will disarm the security system  
immediately. The six second timer is provided for your conve-  
©
2008 Directed Electronics—All rights reserved  
15  
 
nience, in case the system is accidentally triggered.  
Disarming without a transmitter  
If your remote transmitter is lost or damaged, you can manually  
disarm your vehicle security system. To disarm the system  
without a transmitter, you must have the vehicle's ignition key  
®
and know where the Valet switch is located. Be sure to check  
with your installer at the time of installation for both the location  
®
and the preset response (1-5 presses) of the Valet switch.  
To disarm the security system,  
turn the ignition to the ON posi-  
tion. Press the Valet button the  
preset number of times (one to  
DRW-35  
five times) within 15 seconds.  
After five seconds, the system will  
disarm. If the system does not  
disarm, you may have waited too  
long; turn the ignition off and on  
and try again.  
Location of Valet Button_________________________________  
Number of Presses_____________________________________  
Important! The Valet button can be programmed to  
respond to 1-5 presses for the disarm function. You must  
check with the installer to verify the programming for  
your individual unit.  
©
2008 Directed Electronics—All rights reserved  
16  
 
Silent mode  
To temporarily turn off the arm or disarm chirps, use Silent  
Mode™. Simply press  
for less than one second before  
arming or disarming, and the confirmation chirp(s) will be elim-  
inated for that one operation only. If you want the arm/disarm  
chirps turned off permanently, your dealer can do this for you.  
Note: The Warn Away® response to lighter impacts is  
bypassed if the system is armed using Silent Mode. This  
ensures that no chirps will be emitted by the siren in an  
area you want chirp-free. The system is still fully capable  
of triggering. Only the Warn Away® response is  
bypassed.  
Panic mode  
If you are threatened in or near your vehicle, you can attract  
attention by triggering the system with your transmitter. Just  
press  
for two seconds, and you will enter Panic Mode. The  
siren will sound and the parking lights will flash for the  
programmed siren duration. To stop Panic Mode at any time,  
press  
on the remote transmitter again.  
Valet mode  
You can prevent your security system from automatically arming  
and triggering by using Valet Mode. This is very useful when  
washing the vehicle or having it serviced. In Valet Mode, the  
security system will not arm, even with the remote transmitter,  
but all convenience functions (door locks, trunk release, etc.) will  
continue to work normally.  
©
2008 Directed Electronics—All rights reserved  
17  
 
To enter or exit Valet Mode:  
1. Turn the ignition on.  
2. Turn the ignition off.  
DRW-35  
3. Press and release the Valet  
button within 10 seconds.  
The status LED will light solidly if you are entering Valet Mode,  
and it will go out if you are exiting Valet Mode.  
To enter or exit Valet Mode using the transmitter:  
1. Open any vehicle door.  
2. Press  
3. Press  
4. Press  
.
.
again.  
The status LED will light solidly if you are entering Valet Mode,  
and it will go out if you are exiting Valet Mode.  
Remote start  
This feature allows you to remotely start and run your vehicle for  
a programmable period of time. This makes it possible to warm  
up the engine, as well as adjust the interior temperature of the ve-  
hicle with the climate control system. If interior heating or  
cooling is desired, the climate controls must be preset, and the  
fan blower must be set to the desired level prior to remote starting  
the vehicle.  
Important! (1) Never remote start your vehicle when the  
keys are in the ignition, except when performing Valet  
Take-Over, and (2) Never start the vehicle if it is not in  
either PARK or NEUTRAL.  
©
2008 Directed Electronics—All rights reserved  
18  
 
To remote start the vehicle:  
1. Press  
on the transmitter twice within 3 seconds.  
2. The parking lights flash to confirm that the vehicle will  
attempt to start.  
3. In gasoline vehicles, the engine starts 4 seconds after the  
parking lights flash. In diesel vehicles, the engine starts when  
the WAIT-TO-START indicator on the vehicle's dash goes  
out or the programmed delay has ended.  
4. Once the vehicle has started, it runs for the pre-programmed  
period of time (either 12, 24, or 60 minutes - see  
Programming Options section of this guide) or until a shut-  
down input is triggered.  
Important! It is unsafe to operate a vehicle’s motor in a  
garage or other closed off area. Breathing the exhaust  
from the vehicle is hazardous to your health. Never acti-  
vate the remote start in an enclosed space.  
When you are ready to drive the vehicle:  
1. Insert the ignition key and turn  
it to the ON (not START) posi-  
tion.  
2. Press the brake pedal.  
Note: If the brake pedal is pressed before the key is in the  
ON position, the engine will shut down.  
While the vehicle is running during remote start operation, the  
system will monitor the vehicle and will automatically shut down  
the engine if the system receives any of the following  
©
2008 Directed Electronics—All rights reserved  
19  
 
shut-down inputs:  
The brake pedal is pressed.  
The hood is opened.  
The shutdown toggle switch is put into the OFF position.  
The pre-programmed run time (12, 24, or 60 minutes) has  
elapsed.  
Transmitter buttons  
is pressed twice within 3 seconds.  
Rear defogger  
To turn the rear defogger output OFF:  
1. Simultaneously press & release the  
on the remote control.  
+
+
buttons  
2. The lights will flash 2 times.  
3. The rear defogger output will no longer activate when the  
vehicle is remote started.  
Note: If the remote start is on the parking lights will turn  
off then flash 2-times before returning to their normal  
output and the defogger output, if active, will cease.  
To turn the rear defogger output ON:  
1. Simultaneously press & release the  
on the remote control.  
+
+
buttons  
2. The lights will flash 3 times.  
3. The rear defogger output will once again activate when the  
vehicle is remote started.  
©
2008 Directed Electronics—All rights reserved  
20  
 
Note: If the remote start is on the lights will turn off then  
flash 3-times before returning to their normal output and  
the defogger output will activate as programmed.  
Note: If the temperature is greater than 55° F at the time  
of remote start activation, the rear defogger will not acti-  
vate for that start.  
Valet take-over  
The Valet Take-Over feature allows the vehicle to remain running  
after the key has been removed from the ignition. This feature is  
useful for occasions when you wish to exit and lock the vehicle  
for short periods of time, but would like to leave the motor  
running and the climate controls on.  
To perform Valet Take-Over:  
1. Before turning off the engine, press and release  
twice  
within 3 seconds on the transmitter (or press and release the  
optional momentary switch). Then wait five seconds.  
2. Turn the ignition key to the OFF position. (The engine will  
stay running.)  
3. The engine will run until the pre-programmed time elapses  
or a shut-down input is received. (See the previous Remote  
Start section for a complete list of shut-down inputs.)  
Note: This feature will not work if the brake pedal is  
being pressed.  
©
2008 Directed Electronics—All rights reserved  
21  
 
Short-run/turbo  
Short run turbo mode keeps the engine running after arriving at  
you destination for a programmable period of 1, 3, 5 or 10  
minutes. This allows the system’s timer to conveniently cool  
down the turbo after you have left the vehicle.  
To activate:  
1. Park the vehicle and set parking brake.  
2. Remove your foot from the brake pedal and leave the engine  
running.  
3. Press and release the  
time.  
and  
buttons at the same  
4. The lights will flash to indicate the remote start has entered  
short run turbo mode.  
5. Turn off the key, the engine will keep running.  
6. Exit and secure the vehicle.  
7. The engine will turn off after the programmed run time.  
Safety features  
This system has several important safety features to ensure proper  
operation of the motor and prevent accidental damage to the  
engine or its components.  
©
2008 Directed Electronics—All rights reserved  
22  
 
Starter anti-grind circuitry  
Whenever the vehicle is remote started, advanced anti-grind  
circuitry prevents the starter from engaging, even if the key is  
turned to the start position. This prevents damage to the starter  
motor if the key is turned to the start position during remote start  
operation.  
Disabling the remote start system  
This feature allows your system's remote start unit to be  
temporarily disabled to prevent the vehicle from being remote  
started accidentally. This feature is useful if the vehicle is being  
serviced or stored in an enclosed area. To disable the remote start,  
move the shutdown toggle switch to the OFF position. The  
switch can be installed in a location of your choice. Check with  
your installer for recommended locations.  
Location of Shutdown Switch____________________________  
Shut down inputs  
This security system uses several inputs to shut down the remote  
start operation of the motor or prevent remote start if certain  
inputs are active. The two most important are hood and brake  
inputs. The hood input will prevent the motor from starting, as  
well as shut it down, any time the hood is opened. The brake  
pedal will shut down the motor at any time during remote start  
operation, as well as preventing the remote start from activating  
while it is being pressed.  
©
2008 Directed Electronics—All rights reserved  
23  
 
Nuisance prevention® circuitry  
®
Your system has Directed’s Nuisance Prevention Circuitry  
(NPC). It prevents annoying repetitive trigger sequences due to  
faulty door pin switches or environmental conditions such as  
thunder, jackhammers, airport noise, etc.  
Example  
If the alarm triggers three times within a 60-minute period and  
each time the same sensor or switch triggers the alarm, NPC will  
interpret those triggers as false alarms. After the third trigger,  
NPC ignores, or bypasses, that sensor or switch (along with any  
other sensors or switches sharing the same zone) for 60 minutes.  
If the bypassed sensor tries to trigger the security system while it  
is being bypassed, the 60-minute bypass period will start over.  
This ensures that a sensor that is continually being triggered will  
remain bypassed.  
The vehicle doors are protected by NPC differently. If your secu-  
rity system is triggered by an open door for three full cycles, the  
system will bypass the doors until the trigger ceases.  
Note: Arming and disarming the system does not reset  
this function! The only ways to reset a bypassed zone are  
for it to not trigger for 60 minutes, or to turn on the igni-  
tion. If testing your system, it is important to remember  
that the NPC programming can cause zones to be  
bypassed and appear to stop working. If five chirps are  
heard when disarming, NPC has been engaged. If you  
wish to clear the NPC memory, turn the ignition on.  
©
2008 Directed Electronics—All rights reserved  
24  
 
Diagnostics  
The microprocessor at the heart of your system is constantly  
monitoring all of the switches and sensors connected to it. It is  
designed to detect any faulty switches and sensors and prevents  
them from disabling the entire system. The microprocessor will  
also record and report any triggers that occurred during your  
absence. Refer to the System Status Chirps and Table of Zones  
sections of this guide for diagnostic information.  
Arming diagnostics  
If the security system is armed at the same time that an input is  
active (such as a door opening or sensor triggering), you will hear  
one siren chirp to indicate arming and a second siren chirp to  
indicate Bypass Notification. A Bypass Notification chirp means  
that the security system ignores the input that was active when  
the system was armed, until that input ceases. Three seconds after  
that input ceases, the security system will resume normal moni-  
toring. For example, if your vehicle has an interior light exit delay  
and you arm your security system before the interior light turns  
off, you may hear a second Bypass Notification chirp. Once the  
light turns off, however, the security system resumes normal  
monitoring.  
Note: Bypass Notification does not occur when the sys-  
tem is in Silent Mode or if the notification chirps have  
been programmed off by the installer.  
©
2008 Directed Electronics—All rights reserved  
25  
 
Disarming diagnostics  
Extra chirps that are heard when disarming the system are the  
Tamper Alert. If four chirps are heard when disarming the  
system, then the security system was triggered in your absence. If  
five chirps are heard when disarming the system, a zone was trig-  
®
gered so many times that the Nuisance Protection Circuitry has  
bypassed that zone. In either case, the status LED will indicate  
which zone was involved (see Table of Zones section). The security  
system will retain this information in its memory and chirp four  
or five times each time it is disarmed, until the next time that the  
ignition is turned on.  
System status chirps  
The siren will chirp when arming/disarming the system. The  
pattern of chirps will audibly report the system’s status as  
described below.  
Action  
Number of Chirps  
Description  
Arm  
1
System armed  
Arm  
1 (3-second delay), 1  
System armed with  
Bypass Notification  
Disarm  
Disarm  
2
4
System disarmed  
System disarmed with  
Tamper Alert  
Disarm  
5
System disarmed NPC  
active  
©
2008 Directed Electronics—All rights reserved  
26  
 
Table of zones  
A zone is represented by the number of LED flashes used by the  
system to identify a particular type of input. Standard input  
assignments are listed in the following table, along with spaces to  
write in any optional sensors or switches that have been installed.  
ZONE  
(Number of  
DEALER-INSTALLED  
OPTIONS  
LED Flashes)  
DESCRIPTION  
1
2
Trunk Pin  
Instant trigger - a heavier impact  
detected by the shock sensor  
3
4
Door switch trigger  
Instant trigger - for optional  
sensors  
5
Ignition trigger  
Hood Pin  
6
Interpreting zone diagnostics  
Warn Away responses are not reported by arming or disarming  
diagnostics. If you receive a Bypass notification when arming or  
a Tamper Alert notification when disarming, look at the LED.  
Active or triggered zones will be indicated by a pattern of blinks  
by the LED.  
Example  
If zone 3 was active or triggered, the LED will blink three times  
with a two-second pause. Then it will blink three times again,  
and repeat until the ignition is turned on.  
©
2008 Directed Electronics—All rights reserved  
27  
 
Note: Your system stores the last two triggered zones in  
memory. If your system has been triggered but the LED  
has been reset by turning on the ignition, your dealer can  
still recall the last two zones that were triggered. Contact  
your dealer for details.  
Code hopping  
The receiver and transmitters use a mathematical formula called  
an algorithm to change their code each time the transmitter is  
used. This technology has been developed to increase the secu-  
rity of the unit. The control unit knows what the next codes should  
be. This helps to keep the transmitter “in sync” with the control  
unit even if you use the remote control out of range of the  
vehicle. However, if the remote has been pressed many times out  
of range of the vehicle, or the battery has been removed, it may fall  
out of sync with the control unit and fail to operate the system.  
To re-sync the remote simply press  
several times within  
range of the vehicle. The alarm will automatically re-sync and  
respond to the transmitters normally.  
High frequency  
Your system transmits and receives at 434 MHz. This provides a  
cleaner spectrum with less interference and a more stable signal.  
Enjoy a phenomenal increase in range, even in areas with high  
©
2008 Directed Electronics—All rights reserved  
28  
 
radio interference.  
Owner recognition  
Owner Recognition is a revolutionary new feature available only  
®
from Directed. Using a Directed Bitwriter , hand-held program-  
ming tool, your dealer can program many of the system settings.  
The programmer makes it possible to program different settings  
for each transmitter that is used with the system. Then, whenev-  
er a specific transmitter is used, the system will recall the settings  
assigned to that transmitter. Owner Recognition lets up to four  
users of the system have different settings that meet their specific  
needs. It is almost like having four separate alarms in your  
vehicle, one for each user.  
Note: Owner Recognition cannot be programmed with-  
out a Bitwriter® and the necessary software. Check with  
your dealer for more information.  
Rapid resume logic  
This Directed system will store its current state to non-volatile  
memory. If power is lost and then reconnected the system will  
recall the stored state from memory. This means if the unit is in  
Valet Mode and the battery is disconnected for any reason, such  
as servicing the car, when the battery is reconnected the unit will  
©
2008 Directed Electronics—All rights reserved  
29  
 
still be in Valet Mode. This applies to all states of the system  
including arm, disarm, and Valet Mode.  
Power saver mode  
Your system will automatically enter Power Saver Mode while  
armed or in Valet Mode, after a period of time in which no oper-  
ation has been performed. This lowers the current draw on the  
vehicle's battery. Power Saver Mode takes over under the  
following conditions:  
Power Saver when the system is armed: After the system has  
been armed for 24 hours the LED will flash at half its  
normal rate, decreasing the system's current draw.  
Power Saver in Valet Mode: When the system enters Valet  
Mode the LED illuminates steadily. If the vehicle is not used  
(ignition is not turned on) for a one hour period while the  
system is in Valet Mode, the LED will shut off. If the system  
remains in Valet Mode, the LED will come back on the next  
time the ignition is turned on and then back off.  
Programming options  
Programming options control your system's normal, operational  
set-up. Most options do not require additional parts, but some  
may require installation labor.  
©
2008 Directed Electronics—All rights reserved  
30  
 
The following is a list of the programmable options, with the  
factory settings in Bold.  
Active arming (transmitter only) or passive arming (auto-  
matic arming 30 seconds after the last door has been closed).  
Arming/disarming siren chirps on or off.  
The ignition controlled door lock feature on or off: When  
this feature is programmed on, the doors will lock three  
seconds after the ignition is turned on, and unlock when the  
ignition is turned off. If your installer is programming the  
®
security system with the Directed Bitwriter , ignition lock  
and unlock are independent features that can be  
programmed separately.  
Passive door locking (with passive arming) or active door  
locking (only when arming with the transmitter). Passive  
locking allows the vehicle's doors to lock when the security  
system passively arms (after the 30-second countdown). This  
feature only works if passive arming has been programmed.  
Panic mode enabled/disabled when the ignition is turned  
on. (Some states have laws against sirens sounding in moving  
cars.)  
Forced passive arming on or off. If your security system is  
programmed for passive arming and the forced passive  
arming feature has been programmed on, the system will  
passively arm after one hour, even if a protected entry has  
been left open. Forced passive arming ensures that the  
system will be armed if a door has accidentally been left ajar  
when leaving the vehicle.  
31  
©
2008 Directed Electronics—All rights reserved  
 
Note: When the system passively arms after one hour, the  
entry point that has been left open, and anything con-  
nected to the same zone, is bypassed and cannot trigger  
the system. However, the remaining inputs to the system  
are fully operational.  
Full trigger response 30 or 60 seconds: This determines how  
long the full triggered sequence lasts. Some states have laws  
regulating how long a security system can sound before it is  
considered a nuisance. If your installer is programming the  
®
security system with the Directed Bitwriter , the full trig-  
gered response can be programmed for any duration ranging  
from 1 to 180 seconds.  
®
Note: This feature will only function if the FailSafe  
Starter Kill relay has been installed.  
Siren tones and chirp volume. The output of the Revenger  
Soft Chirp siren consists of six different tones in sequence.  
Any of these tones can be eliminated by a dealer, resulting in a  
unique, easily identifiable siren sound. The chirps can be either  
full volume or 6 decibels quieter than the full alarm blast.  
12, 24, or 60 minute run time. your system can be  
programmed to allow the vehicle to run for 12, 24, or 60  
minutes when remote started. Can be set up to minute  
increments by your installer.  
3, 6, 9, or 12 minute timer mode run time. Your system can  
be programmed to allow the vehicle to run for 3, 6, 9, or 12  
32  
©
2008 Directed Electronics—All rights reserved  
 
minutes when remote started in timer mode. Can be set up  
to 16 minutes by your installer.  
While the remote start system is running the engine, the  
parking lights of the vehicle can flash on and off or come on  
and light steadily.  
Comfort closure is a programming option which closes the  
vehicle’s windows after remote locking.  
Security & convenience expansions  
Listed below are some of the many expansion options available.  
Please consult your dealer for a complete explanation of all the  
options available to you.  
Audio Sensor: Metal on glass, glass cracking, and breaking  
glass produce distinctive acoustic signatures. The 506T audio  
sensor uses a microphone to pick up sounds, then analyzes them  
with proprietary acoustic software to determine if the glass has  
been struck.  
Field Disturbance Sensor: An invisible dome of coverage is estab-  
lished by installing the 508D “radar” sensor. Your system can  
react to any intrusions into this field with the full triggered  
sequence.  
Power Locks: This system offers lock outputs that can control  
some manufacturers' power door lock systems. For other  
systems, additional parts may be required.  
©
2008 Directed Electronics—All rights reserved  
33  
 
Power Trunk Release: The accessory output of the system can op-  
erate a factory power release for the vehicle’s trunk or hatch.  
Although the on-board relay can control most power trunk re-  
leases, sometimes an optional relay is required. If the factory  
®
release is not power-activated, Directed 's 522T trunk release  
solenoid can often be added.  
Power Window Control: Automatic power window control is pro-  
vided with the 529T and 530T systems. These can operate  
power windows, and can roll them up automatically when the  
system is armed, roll them down, or both up and down.  
©
2008 Directed Electronics—All rights reserved  
34  
 
Glossary of terms  
Control Unit: The “brain” of your system. Usually hidden under-  
neath the dash area of the vehicle. The control unit houses the  
microprocessor which monitors your vehicle and controls all  
system functions.  
Input: A physical connection to the system. An input can be  
provided by a sensor, pinswitch or by existing systems in the  
vehicle, such as ignition or courtesy lights.  
LED: A red light mounted at a discretionary location inside the  
vehicle. It is used to indicate the status of your system.  
Shock Sensor: This system has a dual zone shock sensor. This  
sensor is mounted in the vehicle and designed to pick up impacts  
to the vehicle or glass.  
Transmitter: A hand-held, remote control which operates the  
various functions of your system.  
Trigger or Triggered Sequence: This is what happens when the  
alarm “goes offor “trips.” The triggered sequence of your  
system consists of the siren sounding and parking lights flashing  
for the programmed duration.  
Valet button: A small push button mounted at a discretionary  
location inside the vehicle. It is used to override the starter inter-  
rupt when a transmitter is lost or damaged, or to enter or exit  
Valet Mode.  
©
2008 Directed Electronics—All rights reserved  
35  
 
Warning Zone Response: Lighter impacts to the vehicle will  
generate the Warning Zone response. It consists of several  
seconds of siren chirps and parking light flashes.  
Zone: A zone is a separate input that the alarm can recognize as  
unique. Each input to the system is connected to a particular  
zone. Often two or more inputs may share the same zone.  
©
2008 Directed Electronics—All rights reserved  
36  
 
Quick reference guide  
Arming  
To arm, press  
. When the system arms, you will hear a short chirp, and  
the parking lights will flash once.  
Arming while driving  
To arm the system while driving, press  
on your transmitter while the  
vehicle is running. The system will chirp once and then once more to indi-  
cate that the ignition is on.  
Arming while driving  
To arm the system while driving, press  
on your transmitter while the  
vehicle is running. The system will chirp once and then once more to indi-  
cate that the ignition is on.  
Disarming  
To disarm, press  
flash twice.  
. You will hear two chirps, and the parking lights will  
High security disarm  
For high security disarm, press  
on your transmitter and the siren will stop  
sounding. To completely disarm the security system, press again and the  
system will chirp 4 or 5 times (reporting the trigger).  
Disarming without a transmitter  
Turn on the ignition. Press the Valet button within 15 seconds. The system  
should now disarm. If it does not, you may have waited too long, so turn the  
ignition off and on and try again.  
Silent Mode™  
Pressing  
tion chirp(s) for that one operation only.  
briefly before arming or disarming will eliminate the confirma-  
Panic Mode  
Press  
and the parking lights will flash for 30 seconds. To stop Panic Mode at any  
time, press on the transmitter again.  
for 2 seconds, and you will enter Panic Mode. The siren will sound  
To remote start the vehicle  
Press twice within 3 seconds. The parking lights will turn on (if  
connected) and the vehicle will start and run for the programmed period of  
time.  
©
2008 Directed Electronics—All rights reserved  
37  
 
To disable the remote start system  
To disable the remote start, move the shutdown toggle switch to the OFF  
position.  
Location of Valet button_________________________________  
Number of Valet button pulses for disarming_______________  
Valet Takeover  
Press and release  
on the transmitter twice in 3 seconds. Turn the  
ignition key to the OFF position. Once the vehicle has started, it will run  
for the pre-programmed period of time (12, 24, or 60 minutes).  
Rear Window Defogger  
Press the  
,
, and  
buttons simultaneously to turn the defog-  
ger on or off when remote starting. When a remote start is initiated, the  
parking lights will flash 2-times if the defogger is set to off, and will  
flash 3-times if the defogger is set to on.  
©
2008 Directed Electronics—All rights reserved  
38  
 
 
The company behind this system is Directed Electronics  
Since its inception, Directed Electronics has had one purpose, to provide consumers with  
the finest vehicle security and car stereo products and accessories available. The recipient of  
nearly 100 patents and Innovations Awards in the field of advanced electronic  
technology, Directed is ISO 9001 registered.  
Quality Directed Electronics products are sold and serviced throughout North America  
and around the world.  
Call (800) 274-0200 for more information about our products and services.  
Directed Electronics is committed to delivering world class quality products  
and services that excite and delight our customers.  
Vista, CA 92081  
© 2008 Directed Electronics—All rights reserved  
G5303L 2008- 07  
 

ACP EP Memory Computer Drive CISURF MBM 1G User Manual
ACTiSYS Computer Accessories ACT IR2000UL User Manual
AllTrade Air Compressor 835534 User Manual
American Standard Plumbing Product 192 User Manual
AO Smith Water Heater ADM 115 User Manual
Atlantic Indoor Furnishings 160 DVD User Manual
Avery Battery Charger 9465 User Manual
Axis Communications Security Camera axis communications dome network camera User Manual
Axor Plumbing Product 4438XX0 User Manual
Azden Barcode Reader PCS 9600D User Manual