Audiovox Satellite Radio 105BP User Manual

Model 105BP  
Transmitter Programming Guide  
These transmitters make use of icons (symbols) to identify the reaction  
your security system/keyless entry/and or remote start system, where  
applicable, will have when any icon (button) is pressed. These  
icons are programmed at time of installation to meet the needs of the  
individual and to complement the vehicle that the system is installed in.  
To replace a transmitter or add transmitters, please follow the  
programming instructions listed on the pages of this manual.  
RECEIVER  
CHANNEL  
SYSTEM FUNCTION  
BUTTON  
Lock And Arm Alarm, also initiate and  
terminates *Panic  
1
Unlock And Disarm, also initiates and  
terminates *Panic. Programmable to  
unlock drivers door and or all doors.  
2
1
Lock and arm/unlock and disarm. May  
be programmed to unlock driver's door  
or all doors. Also will initiate and  
terminate *Panic.  
Pulsed or switched output to control  
Remote Trunk Release or optional  
device connected to channel 3.  
3
3
When pressed and release two times,  
will provide pulsed output or activate the  
Remote Start option when installed.  
When so equipped, this button can be  
used to operate an optional device  
connected to channel 4.  
*4  
*5  
When so equipped, this button can be  
used to operate an optional device  
connected to channel 5.  
* Where So Equipped  
128-8777  
1 of 8  
 
mounted LED will Flash 3 times, indicating that the unit is ready  
to accept programming for channel # 3 which is the trunk re-  
lease/alternate output channel of the system.  
8) Press and hold the trunk/key symbol button of the transmitter you  
wish to program for 4 seconds or until a long chirp is heard from the  
siren.  
"Repeat step 8 for each transmitter you wish to program".  
9) Press and release the valet push button switch one time to advance  
to channel 4 if so equipped. The siren will chirp 4 times and the  
dash mounted LED will Flash 4 times, indicating that the unit is ready  
to accept programming for channel # 4, optional device (where  
equipped)  
10) Press and hold the Option button of the transmitter you wish to  
program for 4 seconds or until a long chirp is heard from the  
siren.  
"Repeat step 10 for each transmitter you wish to program".  
11) Press and release the valet push button switch one time to ad-  
vance to channel 5 if so equipped. The siren will chirp 5 times and  
the dash mounted LED will Flash 5 times, indicating that the unit is  
ready to accept programming for channel # 5 optional device  
(where equipped)  
12) Press and hold the second Option button of the transmitter you  
wish to program for 4 seconds or until a long chirp is heard from  
the siren.  
"Repeat step 12 for each transmitter you wish to program".  
13) Within 10 seconds, press and release the valet program  
switch one time.  
(Siren emits 6 short chirps indicating channel 6 has been entered)  
14) Within 10 seconds, Press and hold the unlock button, (or any  
unused button(s)), of the first transmitter you wish to control  
Channel 6 output, (Driver Priority 1) until a long chirp is heard  
from the siren.  
(Repeat this for each transmitter you wish to operate the Channel 6  
output, Driver Priority 1)  
15) Within 10 seconds, press and release the valet program switch  
one time.  
(Siren emits 7 short chirps indicating channel 7 has been entered)  
16) Within 10 seconds, Press and hold the unlock button (or any  
unused button(s)) of the first transmitter you wish to control  
Channel 7 output, (Driver Priority 2) until a long chirp is heard  
from the siren.  
(Repeat this for each transmitter you wish to operate the Channel 7  
output, Driver Priority 2)  
3
128-8777  
3 of 8  
 
NOTE: Channels 6 and 7 can be used as a separate output to  
control a function other than driver priority. Simply program-  
ming any unused transmitter button other than the unlock  
button will allow complete independent control of these  
outputs.  
ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN:  
NOTE: Before you begin to erase the lost or stolen transmitter(s), have  
all transmitters available that you wish to remain programmed.  
These will be used during the program process to identify  
transmitters that will continue to be used.  
Enter the transmitter program mode:  
1. Turn the ignition switch to the “ON” position.  
2. Within 10 seconds, press and release the valet/program switch  
three times. (Siren emits 1 short chirp indicating channel 1 has  
been entered)  
3. Within 10 Seconds, press and hold the ARM or ARM/DISARM  
button of the first transmitter you wish to remain stored into the  
control unit until a single chirp is heard from the siren.  
(Repeat this for each transmitter you wish to remain stored in the control  
unit).  
The receiver stores up to four transmitters. To be certain all transmitter  
slots in the receiver are occupied with transmitters you wish to con-  
tinue to use, and all others are erased, you will have to fill all four  
receiver slots. If in step 3 you identified one transmitter, you will have  
to fill the additional 3 slots. If in step 3 you identified two transmitters,  
you will have to fill the additional two slots, etc...  
4. Press and hold any unused button or combination of buttons until a  
long chirp is heard from the siren. Release and press the button or  
button combination again and again until all remaining slots are full.  
NOTE: The button or combination of buttons entered will also control  
the arm or arm/disarm function until additional transmitters are  
added. All unwanted transmitters are now deleted.  
REPRIORITIZING A TRANSMITTER’S PROGRAMMING:  
To reprogram a receiver channel with a different transmitter button  
once a code has been stored, there will be two options:  
1. Enter the transmitter program mode of the receiver channel to be  
reprogrammed. Using any unused button or combination of but-  
tons, push out the stored code by pressing the unused button until  
a long chirp is heard, then repeat 3 additional times. After this, you  
can add any desired unused transmitter button. This action erases  
only the button stored of the transmitter you are programming. All  
other codes will remain stored.  
2. Enter the transmitter program mode. Using any transmitter button  
press and hold until a long chirp is heard. If a single chirp or multiple  
chirps, (up to 7 chirps), are heard, the unit is indicating that the  
transmitter has already been programmed elsewhere in the re-  
ceiver. Release the transmitter button and within 5 seconds press  
4
128-8777  
4 of 8  
 
and hold until a long chirp is heard. This action forces the unit to  
erase all stored codes of that transmitter.  
The unit then exits the program mode the siren emits the program mode  
exit chirp pattern. All transmitter buttons for that transmitter must now  
be reprogrammed. Any other transmitter stored in the unit’s memory still  
remain operational. If the button is released and not pressed again  
within the 5 second period, no change in programming has been made  
to the receiver channel. The programmer can move onto a different  
channel or erase the transmitter codes as described in 1 above.  
BATTERY REPLACEMENT:  
The transmitter incorporates a small LED visible through the case which  
is used to indicate battery condition. You will notice a decrease in  
transmitter range as the battery condition deteriorates. Transmit-  
ter battery replacement is recommended at least every 10 to 12 months,  
depending upon how frequently the transmitter is used.  
To replace the battery:  
1) Remove the 3 small # 0 Phillips head screws from the rear of the  
case.  
2) Remove the rear cover to access the discharged battery paying  
attention to the proper polarity orientation.  
3) Carefully remove and properly dispose of the discharged battery.  
4) Insert the new battery with the + side up toward the battery clip.  
Reassemble the case, then reinstall the 3 small case screw re-  
moved in step 1.  
5) If you accidently dislodge the circuit board from the transmitter hous-  
ing, be certain that the rubber membrane is seated properly, and the  
buttons are properly exposed from the front view of the case,  
then insert the circuit board, and return to step #4.  
This Transmitter uses CR2032 Coin Cell Type Batteries.  
SEEASSOCIATED DIAGRAMS ON FOLLOWING PAGE  
5
128-8777  
5 of 8  
 
After removing the three #0  
point phillips screws shown  
pry apart case with the  
edge of a finger nail or a  
small common screwdriver.  
Keep hold of the metal key  
ring loop to prevent it's loss  
as it will separate from the  
transmitter case.  
Carefully remove the  
discharged battery by sliding  
it out from under the clip in  
the direction indicated by the  
arrow in the diagram below.  
Properly dispose of the  
discharged battery and  
insert a new CR2032 taking  
care to arrange it so that the  
+ is facing up toward the +  
symbol on the battery clip.  
Reassemble in the reverse  
of above.  
This device complies with FCC Rules Part 15 Operation is  
subject to the following two conditions  
(1) This device may not cause harmful interference and  
(2) This device must accept any interference that may be  
received, including interference that may cause undesired  
operation.  
NOTE:The manufacturer is not responsible for any radio or  
TV interference caused by unauthorized modifications to  
this equipment. Such modifications could void the user’s  
authority to operate the equipment  
6
128-8777  
6 of 8  
 
ORDERFORMFOR 105BPTransmitter  
Attention: Transmitter Ordering Department  
Important: To help us expedite your order, please print all of the  
information legibly and mail this form and your payment  
according to the instructions below.  
Indicate the pad number of your transmitter selected from the  
pads shown above.  
Note: Transmitter model number found on back of case.  
1)Name: _______________________________________  
2)Address: ______________________________________  
3) City: ________________ State: _____ Zip Code: ________  
4) Telephone Number: (_____) _______________  
5) Total Number Of Transmitters Required:  
Cost Per Transmitter is:  
$75.00  
Multiply By Number Of Transmitters  
X ______  
6) Enter Total Amount Enclosed _________________  
(New York State Residents must include the appropriate sales tax)  
7) Method of Payment:  
Mastercard Visa Check or Money Order (do not send cash)  
Make Checks Payable To Audiovox Corporation  
Credit  
Card  
Number:  
_________________________________  
Credit Card Expiration Date: ____ / _____ / _____  
8) Mail this form along with your payment to:  
Credit card purchasers can order additional or replacement  
transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and  
follow the instructions from the operator interface.  
Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y., 11788  
Attn.:TRANSMITTERDEPARTMENT  
7
128-8777  
7 of 8  
 
This Page Intentionally Blank  
© 2010 Audiovox Electronics Corporation, Hauppauge, NY 11788  
128-8777  
8
128-8777  
8 of 8  
 

3Com Computer Hardware DK8X User Manual
ACDelco Portable Generator AC G0004 User Manual
ADTRAN Network Card ESU 120e User Manual
AKG Acoustics Microphone WMS61 User Manual
Alesis Computer Monitor Monitor One User Manual
Altinex Satellite Radio TP115 110 User Manual
AOSafety Home Safety Product Eyewear Lens User Manual
Audiovox Automobile Alarm PRO 9243 User Manual
Axor Plumbing Product 42090XX0 User Manual
BeefEater Gas Grill Gas Barbecues User Manual