American Standard Plumbing Product 2097012 User Manual

INSTALLATION INSTRUCTIONS

NEW SAVONA 1.6 GPF ONE-PIECE TOILET

Model 2097.012

Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed

properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure

your installation conforms to local codes.

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

NOTE: Pictures may not exactly define contour of china and components.

RECOMMENDED TOOLS AND MATERIALS

Putty Knife

Hacksaw

Regular Screwdriver

Wax Ring/Gasket

Adjustable Wrench

Sealant

Closet Bolts

Tape Measure

Carpenters Level

Flexible Supply Tube

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet flange centerline must be as listed below:

FINISHED WALL

413mm

CLOSET

FLANGE

736mm

(16-1/4)

(29)

23mm

(7/8)

355mm

(14)

176mm

(7)

C/L

C/L OF SEAT POST

HOLES 140mm

(5-1/2) CTR'S.

767mm

(30-1/4)

CLOSET

BOLTS

388mm

(15-5/16)

473mm

(18-1/2)

384mm

(15)

FINISHED

FLOOR

13mm

(1/2)

INSTALL CLOSET BOLTS

Install closet bolts in flange channel, turn 90 , and slide

into place 6" (152 mm) apart and parallel to wall.

203mm

(8)

305mm

(12)

C/L OF SUPPLY

AS REQUIRED

305mm

(12)

343mm

(13-1/2)

NUT

WAX RING

WASHER

BOLT

SEALANT

FLANGE

INSTALL WAX SEAL

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange so bolts project

through mounting holes.

b. Loosely install retainer washers and nuts. Side of washers marked "THIS

SIDE UP" must face up!

Invert toilet on floor (cushion to prevent damage), and

install wax ring evenly around waste flange (horn), with

tapered end of ring facing toilet. Apply a thin bead of

sealant around toilet base.

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .

A S A m e r i c a , I n c . 2 0 0 9

7301387-100

ARM

TOP

REFILL

TUBE

ADJUSTMENTS

NIPPLE

a. Adjust water level. Water level

should be adjusted to level indicated

on tank by adjusting float cup.

TANK

LEVER

CRITICAL LEVEL

MARK ("C.L.")

MUST BE

Fig. 9A

1" ABOVE

"S"

CLIP

OVERFLOW PIPE

See Step 10 for water level adjustment

method.

FLOAT

CUP

b. If bowl fails to siphon, an adjustment

may be required with the lift chain.

Simply remove the bead chain from

the retainment clip (see Fig. 9A) and

take up slack on the chain, and

reinsert on lift rod. Make sure the chain

is not too taught.

FLUSH

VALVE

FILL

VALVE

BODY

WATER LEVEL

ADJUSTMENT

ROD

ADJUSTABLE

HEIGHT

FLAPPER

Turn on water supply.

Submerge the FLOAT CUP

under the water for 30

SHANK

WASHER

seconds. Adjust the water to

desired level by turning

WATER LEVEL ADJUSTMENT

ROD and moving FLOAT CUP

up or down.

THREADED

SHANK

LOCK NUT

CONE WASHER

PARTS FOR WATER

CONNECTION

(SEE STEP 9)

COUPLING NUT

(HAND TIGHT ONLY)

Diagram 1

11 ^{CARE AND CLEANING}

When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,

disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some

bathroom chemicals and cosmetics may damage the seat's finish.

WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the

tank. This damage can cause leakage and property damage.

American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing

chlorine (calcium hypochlorite).

FLUIDMASTER

WATER CONTROL

SEAT AND COVER

(INCLUDES MTG. KIT)

FLUSH VALVE

TANK COVER

FLAPPER

ASSEMBLY

SEAT POST

MTG. KIT

NEW SAVONA ONE-PIECE TOILET

REPAIR PARTS LIST

TRIP

LEVER

NOTE: "XXX" represents color options. Specify when ordering.

1.6

GPF

COMPONENT

DESCRIPTION

Tank Cover

√

735146-400.XXX0A

5205.110.XXX

730835.XXX

7381059-200.XXX

738565-441.0070A

738942-1000A

Seat - Elongated

Bolt Cap Kit Cover

Trip Lever - Right Hand

Inlet Valve

Flush Valve - 1.6 GPF

Flapper Assembly - 1.6 GPF

738920-0070A

BOLT

CAPS

7301387-100

- 3 -

TROUBLESHOOTING

IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK

SLOWLY, repeat Step 12.

IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF

NON-USE, it is a signal you are wasting water because:

LEVER LE

BRAS EN

PREMIER

• The end of the refill tube is inserted into overflow pipe, below

water level in tank. Attach refill tube to overflow pipe using "S"

clip provided.

• The flush valve is leaking because it's worn, dirty or misaligned

with tank ball or flapper (replace with a new flapper).

IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL

OF TANK WATER IS SLOW after valve has been in use for

some time, Fluidmaster Model 242 Replacement Seal may be

needed.

IMPORTANT: Always

• While holding a

• Replace TOP by engaging

lugs and rotating 1/8 turn

clockwise. MAKE

CERTAIN TIP IS TURNED

TO THE LOCKED

POSITION. VALVE MAY

NOT TURN ON IF TOP IS

NOT FULLY TURNED TO

THE LOCKED POSITION.

clear sand and rust from

system.

container over the

uncapped VALVE to

prevent splashing, turn

water supply on and off

a few times. Leave

water supply off.

Go to our website at www.fluidmaster.com for more

solutions to toilet problems.

•

Make sure water supply is

off. Remove valve TOP by

lifting arm and rotating top

and arm 1/8 turn

For troubleshooting information please contact:

counterclockwise, pressing

down slightly on cap.

30800 Rancho Viejo Road

San Juan Capistrano, CA 92675

(949) 728-2000 (800) 631-2011

www.fluidmaster.com

GUARANTEE: This Fluidmaster product is guaranteed to be free from defective materials and

workmanship for a period of one year. Units returned to Fluidmaster will be replaced without charge.

Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster

shall not be responsible or liable for any damages caused by products used with Fluidmaster valves

that were not manufactured by Fluidmaster, Inc.

2001 Fluidmaster, Inc.

Registered trademark of Fluidmaster, Inc.

TROUBLESHOOTING GUIDE

PROBLEM

POSSIBLE CAUSE

CORRECTIVE ACTION

Does not flush

a. Water supply valve closed.

a. Open valve and allow water to fill tank.

b. Supply line blocked.

b. Shut off water supply, disconnect supply line, and inspect

all gaskets and washers. Reassemble. Also, see Fluidmaster

maintenance (see step 12).

c. Flush valve chain too loose or disconnected.

d. Sand or debris lodged in water control.

c. Readjust chain length as required.

d. Shut off water supply. Remove cap and clean per Step 12.

Poor or sluggish flush

a. Bowl water level too low.

a. Check that refill tube is connected to water control and

inserted into tank overflow without being kinked or damaged.

b. Open supply valve fully. Be sure that proper supply tube size is used.

c. Remove obstruction. Consult a plumber if necessary.

d. Normal supply pressure must be at least 20 psi.

b. Supply valve partly closed.

c. Partially clogged trapway and/or drain pipe and/or vent.

d. Supply pressure too low.

Toilet leaks

a. Poor supply line connection.

b. Poor bowl to tank/floor connection.

a. Review Step 8 of installation procedure.

b. Review Step 4 through 6 of installation procedure.

Toilet does not shut off

a. Flush valve chain too tight, holding flush valve open.

b. Flush valve seat and/or flapper worn or deformed.

c. Sand or debris lodged in water control.

a. Readjust chain length as needed. Review step 9.

b. Replace flapper/flush valve assembly, as needed.

c. Shut off water supply. Remove cap and clean per Step 12.

ONE YEAR LIMITED WARRANTY

This limited warranty applies only to the original purchaser and installation of the products. In the event of a limited warranty claim, proof of purchase will be

required - save sales receipt.

For this warranty to become effective, the accompanying warranty registration card and proof of purchase must be completed and returned to the address on

the warranty registration card within 30 days of purchase.

If inspection of this AS America, Inc. (”American Standard”) plumbing product, inclusive of china and all mechanical components, within five years after its initial

purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.

This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with

a local building or plumbing contractor to insure local code compliance before installation.

This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse,

accident or other damage; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the

product as shipped by American Standard.

This warranty DOES NOT COVER any damage caused by the use of in-tank cleaners.

American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall

American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of

a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied

warranties, so this exclusion may not apply to you.)

This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this

warranty does not affect such statutory rights.

For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that

a service request (including a description of the product model and of the defect) be sent to the following address:

In Canada:

AS Canada ULC

In Mexico:

In the United States:

American Standard Brands

Customer Service Manager

AS Maquilia Mexico, S.A. de C.V.

Via Morelos #330

2480 Stanfield Rd.

P.O. Box 6820

Mississauga, Ontario