American Standard Hot Tub 1730 SERIES User Manual

COLONY™ CORNER  
HIGH GLOSS ACRYLIC  
SHOWN LESS ALL FITTINGS  
1730 SERIES  
WHIRLPOOL/BATHING POOL  
INSTALLATION INSTRUCTIONS  
THANK YOU...  
for selecting an American Standard bath. Your new  
1064mm  
(41-7/8)  
1514mm  
(59-5/8)  
bath is shipped to you after careful inspection. The  
whirlpool version is completely assembled with pump,  
ALT.  
PUMP  
motor, and system piping. All you need to finish the  
installation are your selected fittings and electrical  
connections for a whirlpool.  
1546mm  
(60-7/8)  
To insure maximum performance and pleasure from  
PUMP  
this product, please follow the instructions and  
483mm  
(19)  
PROVIDE ACCESS  
FOR SERVICING  
cautions.  
318mm  
(12-1/2)  
686mm  
(27)  
PUMP & CONTROLS  
1168mm  
(46)  
ON/OFF  
SWITCH  
(6) JETS  
C/L OF DRAIN  
OUTLET  
List of Optional Components (not included):  
2 AIR  
VALVES  
• Apron Kit*  
2134mm  
(84)  
LEVELING  
STRINGER  
NOT FOR  
SUPPORT  
TOP OF  
DECK  
83mm  
(3-1/4)  
51mm  
(2)  
* see your American Standard Distributor  
List of Required Components (not included):  
• Drain 1583.470*  
• Bath Filler*  
495mm  
(19-1/2)  
445mm  
*(17-1/2)  
70mm  
(2-3/4)  
117mm  
(4-5/8)  
* see your American Standard Distributor  
ROUGH  
FLOOR  
38mm (1-1/2)  
O.D. TAILPIECE  
BATH SUPPORT MATERIAL  
List of Required Tools and Supplies:  
* NOTE: If the optional apron (PN 0730.121) is to be used with this  
tub, the stringer height must be referenced from the finished floor.  
Tools  
Supplies  
• Level  
• Nails  
• Tape Measure  
• Pipe Wrench  
• Slip Joint Pliers  
• Screw Driver  
• Standard  
Woodworking Tools  
• Personal Safety  
Equipment  
• Putty  
GENERAL SPECIFICATIONS FOR 1730 WHIRLPOOL  
INSTALLED SIZE  
WEIGHT  
60 x 60 x 19-1/2 In.(1524 x 1524 x 495mm)  
115 Lbs. (52 Kg.)  
• Caulking (waterproof)  
• 1 x 3 or 2 x 2  
Stringers  
WEIGHT w/WATER  
GAL. TO OVERFLOW  
908 Lbs. (412 Kg.)  
95 Gal. (360 L.)  
WHIRLPOOL MIN. OPERATING VOL.  
BATHING WELL AT SUMP  
65 Gal. (246 L.)  
30 x 50 In. (762 x 1270mm)  
• Drop Cloth  
• 15 amp GFCI  
Outlet  
BATHING WELL AT RIM  
WATER DEPTH TO OVERFLOW  
FLOOR LOADING  
45-1/2 x 63-1/2 In.(1156 x 1613mm)  
13 In. (330 mm)  
36 Lbs./Sq. Ft. (177 Kgs/Sq. m.)  
• Cement, Plaster,  
Grout  
(PROJECTED AREA)  
• Caulking Gun  
PTS.  
CUBE (FT3)  
27.8  
54  
WHIRLPOOL ELECTRICAL SPECIFICATIONS  
SYSTEM I PUMP  
1.1 HP, 9.9 AMPS, 120V.  
GENERAL INSTALLATION INFORMATION  
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor  
immediately. After inspection and during installation, protect the bath from construction damage. After installation, and before  
enclosing with wallboard, tile, etc., water test the unit and check for leaks.  
If a whirlpool, do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect  
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or  
piping system.  
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing  
materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess  
installations).  
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.  
WARNING! Do not lift whirlpool by the piping harness at any time.  
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.  
© American Standard Inc. 2003  
753451-100 Rev. A  
All product names listed herein are trademarks  
of American Standard Inc. unless otherwise noted.  
 
ELECTRICAL INSTALLATION INSTRUCTIONS  
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other  
applicable codes.  
WARNING:  
When using electrical products, basic precautions should always be observed, including the following:  
1. DANGER: RISK OF ELECTRIC SHOCK  
Connect only to a circuit protected by a ground-fault circuit interrupter.  
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.  
3. Install to permit access for servicing.  
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).  
The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the  
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded  
neutral wire and a third wire, earth ground, are essential.  
ELECTRICAL INSTALLATION  
SEPARATE 15 AMP GFCI  
OUTLET  
WHIRLPOOL MOUNTED  
120 VAC  
AIR SWITCH OR  
WALL TIMER  
PUMP/MOTOR  
GND.  
ELECTRICAL DIAGRAM  
READ AND FOLLOW ALL INSTRUCTIONS  
(3)  
753451-100 Rev. A  
 
WIRE SELECTION GUIDE  
Maximum distance from  
fusebox to motor  
The sizes shown on this  
chart are recommendations  
for copper conductors  
only. Always follow  
local and national  
Motor  
Hi Performance  
Rating  
50'  
100'  
120V Power Line  
12 10  
150'  
200'  
electrical codes  
1.1  
12  
8
DRAIN CONNECTION AND SYSTEM TEST  
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the  
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of  
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings  
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is  
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the  
whirlpool is running.  
POST INSTALLATION CLEAN-UP  
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.  
Do not use wire brushes or any other metal implement on bath surface.  
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or  
®
stains may be removed using granular Spic and Span mixed with water.  
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.  
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.  
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing  
with a white automotive-type polishing compound and waxing with a liquid wax.  
®
(4)  
SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE  
753451-100 Rev. A  
 

AEG Freezer A92860GNB0 User Manual
Agri Fab Power Roller 24192 User Manual
AKG Acoustics DJ Equipment WLS 6060 MAX User Manual
Altinex Switch MT110 101 User Manual
American Standard Bathroom Aids 5030LBW User Manual
Ask Proxima Projector C160 User Manual
Axis Communications Security Camera Axis 232D User Manual
Axor Indoor Furnishings 39293XXX User Manual
Bakers Pride Oven Fryer LPF User Manual
BC Speakers Portable Speaker ME90 User Manual