American Audio DJ Equipment Versadeck User Manual

VERSADECK  
Featuring:  
User Guide  
and Reference Manual  
4/11  
 
IMPORTANT INFORMATION  
CAUTION  
IMPORTANT SAFETY ITEMS FOR  
U.S.A. & CANADA MODEL ONLY  
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS  
(POLARIZED) PLUG WITH AN EXTENSION CORD,  
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES  
CAN BE CAREFULLY INSERTED TO PREVENT BLADE  
EXPOSURE  
WARNING:  
TO PREVENT FIRE OR SHOCK HAZARD,  
DO NOT EXPOSE THIS MEDIA PLAYER TO  
WATER OR MOISTURE  
CAUTION:  
USE OF CONTROLS OR ADJUSTMENTS OTHER  
THAN THOSE SPECIFIED HEREIN MAY RESULT  
IN HAZARDOUS RADIATION EXPOSURE  
CAUTION:  
1. Handle the power supply cord carefully. Do not  
damage or deform; it may cause electric shock  
or malfunction when used. Hold plug attach-  
ment when removing from wall outlet. Do not  
pull on the cord.  
THE MEDIA PLAYER SHOULD NOT BE ADJUSTED  
OR REPAIRED BY ANYONE EXCEPT PROPERLY  
QUALIFIED SERVICE PERSONNEL.  
2. To avoid electric shock, do not open the top  
cover when the unit is plugged in. If problems  
occur with the unit, call your local American  
Audio® dealer.  
NOTE:  
This unit may cause interference to radio and  
television reception.  
3. Do not place metal objects or spill liquid inside  
the media player. Electric shock or malfunction  
may occur.  
Please carefully read and understand the  
instructions in this manual thoroughly before  
attempting to operate this unit. These instruc-  
tions contain important safety information  
regarding the use and maintenance of this unit.  
Take special care to follow all warning symbols  
and labels both on the unit and printed in this  
manual. Also, Please keep this manual with the  
unit, for future reference.  
CAUTION  
Do not open -  
Risk of electric shock  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE THE COVER RACK.  
THERE ARE NO USER SERVICEABLE PARTS  
INSIDE REFER SERVICE TO YOUR  
AUTHORIZED American Audio DEALER.  
CAUTION: TO PREVENT ELECTRIC SHOCK  
DO NOT USE THIS (POLARIZED) PLUG WITH  
AN EXTENSION CORD, RECEPTACLE, OR  
OTHER TYPE OF ELECTRICAL OUTLET  
UNLESS THE WIDE BLADES CAN BE  
CAREFULLY INSERTED INTO A MATCHING  
WIDE SLOT.  
The lightning flash with an arrow triangular  
symbol is intended to alert the user to the  
presence of non insulated “dangerous volt-  
age” within the products enclosure, and  
may be of sufficient magnitude to constitute  
a risk of electric shock.  
The exclamation point triangular symbol is  
intended to alert the user to the presence  
of important operating and maintenance  
(servicing) instructions in the user manual  
accompanying the media player.  
ATTENTION: POUR PREVENIR LES CHOCS  
ELECTRIQUES NE PAS UTILISER CETTE  
FICHE POLARISEE AVEC UN PROLON-  
GATEUR, UNE PRISE DE COURANT OU  
UNE AUTRE SORTIE DE COURANT, SAUF  
SI LES LAMES PEUVENT ETRE INSEREES A  
FOND SANS EN LAISSER AUCUNE PARTIE A  
DECOUVERT.  
©American Audio®  
-
-
VERSADECK Instruction Manual Page 3  
 
ELECTRICAL SAFETY PRECAUTIONS  
ELECTRICAL PRECAUTIONS  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
The lightning flash with arrowhead symbol, within an  
equilateral triangle, is intended to alert the user to the  
presence of uninsulated "dangerous voltage" within the  
product'senclosurethatmaybeofsufficientmagnitude  
to constitute a risk of electric shock to persons.  
The exclamation point within an equilateral triangle is  
intended to alert the user to the presence of important  
operating and maintenance (servicing) instructions in  
the literature accompanying the appliance.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC  
SHOCK, DO NOT REMOVE THE COVER (OR BACK).  
THERE ARE NO USER SERVICEABLE PARTS  
INSIDE REFER SERVICE TO YOUR AUTHORIZED  
AMERICAN AUDIO® SERVICE TECHNICIAN.  
IMPORTANT SAFETY INSTRUCTIONS  
OBJECT AND LIQUID ENTRY - Never push objects of  
READ INSTRUCTIONS — All the safety and operating  
GROUNDING OR POLARIZATION  
instructions should be read before the product is  
operated.  
Ifthisproductisequippedwithapolarizedalternating  
current line plug (a plug having one blade wider than  
theother), itwillfitintotheoutlet onlyoneway. This  
isasafetyfeature.Ifyouareunabletoinserttheplug  
fullyintotheoutlet, tryreversingtheplug. Iftheplug  
should still fail to fit, contact your electrician to  
replace your obsolete outlet. Do not defeat the  
safety purpose of the polarized plug.  
any kind into this product through openings as they  
may touch dangerous voltage points or short-out  
parts that could result in a fire or electric shock.  
Never spill liquid of any kind on the product.  
RETAIN INSTRUCTIONS — The safety and operating  
instructionsshouldberetainedforfuturereference.  
HEED WARNINGS — All warnings on the product and  
in the operating instructions should be adhered to.  
FOLLOW INSTRUCTIONS — All operating and use  
instructions should be followed.  
SERVICING — Do not attempt to service this product  
yourself as opening or removing covers may expose  
you to dangerous voltage or other hazards. Refer all  
servicing to qualified service personnel.  
CLEANING — The product should be cleaned only with  
a polishing cloth or a soft dry cloth. Never clean with  
furniture wax, benzine, insecticides or other volatile  
liquids since they may corrode the cabinet.  
If this product is equipped with  
a
three-wire  
DAMAGEREQUIRINGSERVICE - Unplugthisproduct  
from the wall outlet and refer servicing to qualified  
service personnel under the following conditions:  
groundingtypeplug,aplughavingathird(grounding)  
pin, itwillonlyfitintoagroundingtypepoweroutlet.  
Thisisasafetyfeature.Ifyouareunabletoinsertthe  
plug into the outlet, contact your electrician to  
replace your obsolete outlet. Do not defeat the  
safety purpose of the grounding type plug.  
When the power-supply cord or plug is damaged.  
If liquid has been spilled, or objects have fallen into  
the product.  
ATTACHMENTS  
Do not use attachments not  
recommendedbytheproductmanufacturerasthey  
may cause hazards.  
WATER AND MOISTURE — Do not use this product  
near water — for example, near a bathtub, wash  
bowl,kitchensink,orlaundrytub;inawetbasement;  
or near a swimming pool; and the like.  
ACCESSORIES — Do not place this product on an  
unstable cart, stand, tripod, bracket, or table. The  
product may fall, causing serious injury to a child or  
adult, and serious damage to the product. Use only  
If the product has been exposed to rain or water.  
Iftheproductdoesnotoperatenormallybyfollowing  
theoperatinginstructions.Adjustonlythosecontrols  
that are covered by the operating instructions as an  
improper adjustment of other controls may result in  
damage and will often require extensive work by a  
qualified technician to restore the product to its  
normal operation.  
POWER-CORD PROTECTION - Power-supply cords  
should be routed so that they are not likely to be  
walked on or pinched by items placed upon or  
against them, paying particular attention to cords at  
plugs,conveniencereceptacles,andthepointwhere  
they exit from the product.  
OUTDOOR ANTENNA GROUNDING — If an outside  
antennaorcablesystemisconnectedtotheproduct,  
be sure the antenna or cable system is grounded so  
astoprovidesomeprotectionagainstvoltagesurges  
andbuilt-upstaticcharges.Article810oftheNational  
ElectricalCode,ANSI/NFPA70,providesinformation  
with regard to proper grounding of the mast and  
supporting structure, grounding of the lead-in wire  
to an antenna discharge unit, size of grounding  
conductors, location of antenna-discharge unit,  
connection to grounding electrodes, and  
requirementsforthegroundingelectrode.SeeFigure  
A.  
LIGHTNING — For added protection for this product  
duringalightningstorm,orwhenitisleftunattended  
and unused for long periods of time, unplug it from  
the wall outlet and disconnect the antenna or cable  
system. This will prevent damage to the product  
due to lightning and power-line surges.  
POWER LINES An outside antenna system should  
notbelocatedinthevicinityofoverheadpowerlines  
or other electric light or power circuits, or where it  
can fall into such power lines or circuits. When  
installing an outside antenna system, extreme care  
should be taken to keep from touching such power  
lines or circuits as contact with them might be fatal.  
OVERLOADING — Do not overload wall outlets,  
extensioncords,orintegralconveniencereceptacles  
as this can result in a risk of fire or electric shock.  
If the product has been dropped or damaged in any  
way.  
When the product exhibits a distinct change in  
performance — this indicates a need for service.  
with  
a
cart, stand, tripod, bracket, or table  
recommended by the manufacturer, or sold with  
the product. Any mounting of the product should  
follow the manufacturer’s instructions, and should  
use a mounting accessory recommended by the  
manufacturer.  
REPLACEMENT PARTS -- When replacement parts  
arerequired,besuretheservicetechnicianhasused  
replacement parts specified by the manufacturer or  
have the same characteristics as the original part.  
Unauthorizedsubstitutionsmayresultinfire,electric  
shock, or other hazards.  
SAFETY CHECK - Upon completion of any service or  
repairs to this product, ask the service technician to  
performsafetycheckstodeterminethattheproduct  
is in proper operating condition.  
CART — A product and cart combination should be  
moved with care. Quick stops, excessive force, and  
uneven surfaces may cause the product and cart  
combination to overturn.  
WALL OR CEILING MOUNTING — The product should  
not be mounted to a wall or ceiling.  
HEAT The product should be situated away from heat  
sources such as radiators, heat registers, stoves, or  
other products (including amplifiers) that produce  
heat.  
VENTILATION — Slots and openings in the cabinet are  
provided for ventilation and to ensure reliable  
operation of the product and to protect it from  
overheating, and these openings must not be  
blocked or covered. The openings should never be  
blocked by placing the product on a bed, sofa, rug,  
or other similar surface. This product should not be  
placed in a built-in installation such as a bookcase or  
rack unless proper ventilation is provided or the  
manufacturer’s instructions have been adhered to.  
POWER SOURCES —This product should be operated  
only from the type of power source indicated on the  
marking label. If you are not sure of the type of  
power supply to your home, consult your product  
dealer or local power company.  
ANTENNA  
LEAD IN  
WIRE  
GROUND  
CLAMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
LOCATION – The appliance should be installed in a  
stable location.  
NONUSE PERIODS – The power cord of the appliance  
should be unplugged from the outlet when left un-  
used for a long period of time.  
ELECTRIC  
SERVICE  
EQUIPMENT  
GROUNDING CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
Fig. A  
NEC — NATIONAL ELECTRICAL CODE  
©American Audio®  
-
-
VERSADECK Instruction Manual Page 4  
 
SAFETY INSTRUCTIONS  
I. Read Instructions - All the safety and oper-  
ating instructions should be read before  
you operate the system. The safety and  
operating instructions should be saved  
for future reference.  
The serial and model number for this unit is  
located on the rear panel. Please write down the  
numbers here and retain for future reference.  
Model No._____________________________  
Serial No._____________________________  
2. Heed Warnings - All warnings on the system  
and in the operating instructions should be  
adhered to.  
Purchase Notes:  
3. Water and Moisture - The system should not  
be used near water - for example, near a  
bath tub, kitchen sink, laundry tub, in a wet  
basement or near a swimming pool, etc.  
Date of Purchase_______________________  
Dealer Name__________________________  
Dealer Address_________________________  
4. Ventilation - The system should be situated  
so that its location or position does not  
interfere with its proper ventilation. For exam  
ple, the system should not be situated on a  
bed, sofa, rug, or similar surface that may  
block the ventilation openings; or, placed in  
a built-in installation, such as a bookcase or  
cabinet that may impede the flow of air  
through the ventilation openings.  
__________________________________________  
________________________________________  
Dealer Phone__________________________  
5. Heat - The system should be situated away  
from heat sources such as radiators, heat  
registers, stoves, or other appliances (includ-  
ing amplifiers) that produce heat.  
6. Power Sources - The system should be con-  
nected to a power supply only of the type  
described in the operating instructions or as  
marked on the system.  
7. Servicing - The user should not attempt to  
service the system beyond that described  
in the operating instructions. All other ser-  
vicing should be referred to qualified service  
personnel. The system should be serviced  
by qualified service personnel when:  
A. The power-supply cord or the plug has  
been damaged.  
B. Objects have fallen, or liquid has been  
spilled into the system.  
C. The system has been exposed to rain  
or water.  
D. The system does not appear to operate  
normally or exhibits a marked change  
in performance.  
©American Audio®  
-
-
VERSADECK Instruction Manual Page 5  
 
UNPACKING  
Every VERSADECK has been thoroughly tested and has been shipped in perfect operating condition.  
Carefully check the shipping carton for damage that may have occurred during shipping. If the carton  
appears to be damaged, carefully inspect your system for any damage and be sure all equipment  
necessary to operate the system has arrived intact. In the event damage has been found or parts are  
missing, please contact our toll free customer support number for further instructions. Please do not  
return the system to your dealer without first contacting customer support.  
INTRODUCTION  
Introduction:  
Congratulations and thank you for purchasing the American Audio® VERSADECK. This VERSADECK  
is a representation of American Audio’s continuing commitment to produce the best and highest qual-  
ity audio products possible at an affordable price. Please read and understand this manual completely  
before attempting to operate your new media player. This booklet contains important information con-  
cerning the proper and safe operation of your new media player.  
Customer Support:  
American Audio® provides a toll free customer support line, to provide set up help and answer any  
question should you encounter problems during your initial set up or operation. You may also visit us  
through Friday 8:00 a.m. to 4:30 p.m. Pacific Standard Time.  
Voice:  
Fax:  
(800) 322-6337  
(323) 582-2941  
E-mail:  
Caution! There are no user serviceable parts inside this media system. Do not attempt any repairs  
yourself, without being instructed to do so by an authorized American Audio service technician. Doing  
so will void your manufactures warranty. In the unlikely event your media player may require service,  
please contact American Audio® customer support.  
Do not discard the packing carton in the trash. Please recycle when ever possible.  
SET-UP PRECAUTIONS  
Please be sure to make any connections before plugging the player in to an electrical outlet. All fader  
and volume controls should be set to zero or minimum position, before the system is switched on.  
If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do not  
switch on the system immediately. The arising condensation of water might damage your device.  
Leave the device switched off until it has reached room temperature.  
Operating Determinations:  
• When installing this system, please make sure that the device is not exposed or will not be  
exposed to extreme heat, moisture or dust!  
• Do not operate the system in extremely hot (more than 30°/86°F) or extremely cold (less than  
5°C/40°F) surroundings.  
• Keep the unit out of direct sunlight and away from heaters.  
• Operate the system only after becoming familiar with its' functions. Do not permit operation by  
persons not qualified for operating the unit. Most damages are the result of unprofessional opera-  
tion.  
©American Audio®  
-
-
VERSADECK Instruction Manual Page 6  
 
MAIN FEATURES  
• Plays Mp3/WAV* filles from either USB Stick or SD/SDHC Card via USB Card Reader  
• ID3 Track Recognition  
• Auto cue  
• Real Time Scratch Play  
• Skid Effect  
• 1/75th second frame search  
• Filter Effect  
• Real time cue (“Cue on the Fly”)  
• 8 different speed scan (4 Forward/4 Reverse)  
• Pitch display  
• Echo Effect  
• Flanger Effect  
• System Lock  
• RCA Stereo outputs  
• Large bright VFD display can be viewed from wide angles.  
• Folder Search for Mp3's  
• Music Master tempo  
• Fader “Q” Start Control (a)  
• Cue Mixing  
• Seamless Loop (uninterrupted loop playback)  
• Sampler (Forward & Reverse Sampling)  
• 10 Second Digital Anti-Shock  
• 3 Band EQ per channel  
• Front & Rear Access Mic Jack  
• Master & Booth Outputs  
• 2 Phono & 2 Line Level Inputs  
• Balanced XLR Outputs  
• Headphone Jack w/ Volume Control  
• Flip-Flop (Relay Playback) (b)  
• Jog Wheel Pitch Bend +/-100%  
• Jog Wheel Sensitivity Adjustment  
• Selectable Single or Continuous Play  
• 4 Programmable Cue (Bank) Buttons  
• Adjustable Pitch Percentages: +/-6%, +/-10%, or +/-16%  
• Instant Start within 10ms (sound is produced immediately when the PLAY button is pressed)  
* WAV Files: 1411Kbps PCM  
(a) FADER “Q” START CONTROL: Set up your VERSADECK as described in the set-up section of this manual. After  
set up is completed load your players. By moving the mixer’s crossfader from left to right you can start and pause  
each players playback functions. For Example, when using the VERSADECK player, if your mixer’s crossfader is all  
the way to the left (player one is playing, player two is in cue or pause mode), and you move the fader at least 20%  
to the right, player two (2) will begin to play. When the crossfader is to the right, and you move it 20% to the left,  
player one (1) will begin to play. You can create great effects similar to scratching with this feature. After storing cue  
points on each side of the player, different songs may quickly be recalled by moving the mixer crossfader back  
and forth. New cue points can be easily selected on the VERSADECK player (see setting cue points page 22). “Q”  
Start control is easy to use and mastering this feature will help you create amazing effects with your music.  
(b) RELAY (FLIP-FLOP): Connect your VERSADECK player as described in the set-up section of this manual. This  
feature will start the next player once one (1) player has ended. For example, if player one (1) is playing a track and  
it ends, player two (2) will instantly begin to play. You may set RELAY to play track to track or folder to folder. For  
more information on this feature, see RELAY (FLIP-FLOP™) on page 33.  
©American Audio®  
-
-
VERSADECK Instruction Manual Page 7  
 
SET-UP  
USB INFORMATION:  
• The VERSADECK will only read MP3 files or WAV files.  
• If you are using a SD Card via USB SD Card reader, you must remove the USB SD Card  
reader first to change SD Card's. Please do not remove the SD Card from the USB SD Card  
reader while the USB card reader is still connected to the unit.  
NOTE: For higher quality MP3 files (more than 128 kbps) American Audio recommends "High  
Speed" SD Cards. Using high speed cards will ensure the best performance with your American  
Audio Player.  
• Only supports FAT/FAT32 formatted devices.  
NOTE: If the VERSADECK cannot read your USB device, please make sure that it FAT format-  
ted.  
1. Checking the Contents  
Be sure your VERSADECK was shipped with the following:  
1) VERSADECK Professional media player/mixer  
2) Software CD  
3) Warranty card  
4) Power Cord  
CAUTION:  
To avoid severe damage to the unit, be sure the power is off when making connections to  
the unit.  
System Power Up Sequence:  
1. Turn ON the VERSADECK.  
2. Next turn ON your speakers.  
System Power Up Sequence with connected mixer, amp, active speakers, or external device:  
1. Turn ON the amp, mixer, speakers, or any external device first.  
2. Next turn ON the VERSADECK.  
CAUTION:  
• The VFD is designed to be clearly visible within the angles shown in Figure 1. Mount the unit so  
that the visual angle is within this range.  
10˚  
50˚  
Figure 1  
©American Audio®  
-
-
VERSADECK Instruction Manual Page 8  
 
GENERAL FUNCTIONS AND CONTROLS  
PLAYER  
Figure 2  
23  
1
22  
21  
2
3
4
20  
19  
18  
5
6
17  
7
8
9
10  
16  
15  
11  
12  
14  
13  
A. TOP UNIT PLAYER CONTROLS (FIGURE 2)  
1. FOLDER SEARCH KNOB - Turning this knob will let you search for your desired folder. Turn the  
knob to scroll backward and forward through folders. The folder number your are currently in will be  
shown in the VFD.  
2. SOURCE SELECT BUTTON - This button lets you toggle between USB Port 1 & USB Port 2.  
This selector lets you choose which source will play on either side. The corresponding LED's located  
above the button will verify which source is active. The source selection can only be done in PAUSE  
mode.  
3. CLEAR BUTTON - Use this button to clear the BANK BUTTONS (19). Press this button and then  
press the BANK BUTTON (19) you would like to clear.  
4. PITCH ON/OFF BUTTON - This button is used to switch the pitch function on and off. When the  
button LED is lit the PITCH SLIDER (10) is active. When the button LED is not lit, the PITCH SLIDER  
(10) is not active. The pitch percentage can be changed between 6%, 10%, and 16%; 6% will allow  
the least amount of pitch manipulation and 16% will allow the most amount of pitch manipulation.  
5. PITCH PERCENTAGE SELECTOR - Press this button to select pitch range percentages of 6%,  
10%, and 16%. See adjusting the PITCH SLIDER'S RANGE on page 26.  
6. TEMPO LOCK FUNCTION - This button activates the TEMPO LOCK function. This function allows  
©American Audio®  
-
-
VERSADECK Instruction Manual Page 9  
 
GENERAL FUNCTIONS AND CONTROLS (Cont.)  
PLAYER  
you to use the PITCH SLIDER to speed up or slow down playback speed without altering the tonal  
pitch of the track. When this function is not engaged the original tonal pitch of the track will be altered  
giving you the "chipmunk" effect when a track is played at a high rate of speed, or the "James Earl  
Jones" effect when a track is slowed to much.  
7. SGL/CTN - This function allows you to choose between single track play or continuous track play  
(all tracks in order). This function also operates in RELAY (FLIP-FLOP) mode, when RELAY is acti-  
vated.  
8. TIME BUTTON - The TIME button will switch the time value described in the TIME METER between  
ELAPSED PLAYING TIME & TRACK REMAINING TIME.  
9. JOG WHEEL MODE BUTTONS - The JOG WHEEL has 3 effect functions;  
• A. Cue Scratch Mode:  
In Playback Mode - While in playback mode the JOG WHEEL can be used to return the unit to  
the last set CUE point. Simply touch the JOG WHEEL surface and the unit will immediately re  
turn you to the last set CUE point and start playback.  
In Pause Mode - When the player is paused, touching the JOG WHEEL surface will start play-  
back and will continue to playback until the JOG WHEEL is released. Once the JOG WHEEL is  
released the unit will return to the last CUE point.  
• Vinyl Mode: When this mode is active, use the JOG WHEEL to simulate turntable scratching.  
• CDJ Mode:  
In Playback Mode - When this mode is active the JOG WHEEL can work as a pitch bend dur-  
ing playback. Turning the wheel clockwise will increase the pitch percentage up to 100%, and  
turning the wheel in the counter-clock wise direction will decrease the pitch percentage down to  
-100%. The pitch bend will be determined on how long you turn the jog wheel continuously.  
In Pause Mode - When the player is paused, you can use the JOG WHEEL to frame search.  
10. PITCH SLIDER - This slider is used to adjust the playback pitch percentage. The slider is a set  
adjustment and will remain set until the pitch slider is moved or the pitch function has been turned  
off. This adjustment can be made with or without a disc in the drive. The pitch adjustment will remain  
even if a disc has been removed and will reflect on any other disc loaded into the player. That is to  
say, if you set a +2% pitch on one disc, remove that disc and insert another, that disc too will have a  
+2% pitch. The amount of pitch being applied will be displayed in the VFD (23).  
11. (+) PITCH BEND BUTTON - The (+) pitch bend function creates a momentary “BUMP” in the  
audio's BPM’s (Beats per minute) while it is playing. This will allow you to match the beats between  
the two playing deck’s or any other music source. Remember, this is a momentary function. When  
you remove your finger from this button, the BPM’s will automatically return to PITCH SLIDERS (10)  
selected pitch. Holding down this button will give a maximum of +16% pitch.  
(-) PITCH BEND BUTTON - The (-) pitch bend function creates a momentary “Slow Down” in the  
audio’s BPM’s (Beats per minute) while it is playing. This will allow you to match the beats between  
the two playing deck’s or other playing music source. Remember, this is a momentary function. When  
you remove your finger from the pitch button, the BPM’s will automatically return to PITCH SLID-  
ERS (10) pitch value. Holding down this button will give a maximum of -16% pitch. Use this function  
to slow to another playing music source. Be sure to notice that this function is a momentary pitch  
adjustment, for a more precise adjustment use the PITCH SLIDER (10) to match the BPM’s with  
another playing music source.  
©American Audio®  
-
-
VERSADECK Instruction Manual Page 10