/////alpine®
Printed in Taiwan R.O.C.
TME-M580
5.8-INCH WIDE LCD COLOR MONITOR
OWNER’S MANUAL
Please read before using this equipment.
Points to Observe for Safe Usage
CAUTION
This symbol means important instructions.
Failure to heed them can result in injury or material property damage.
ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE. Route the
cables and wiring away from moving parts (like the seat rails) or sharp or pointed edges. This will prevent
crimping and damage to the wiring. If wiring passes through a hole in metal, use a rubber grommet to prevent
the wire’s insulation from being cut by the metal edge of the hole.
USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY. Be sure to use only the specified
accessory parts. Use of other than designated parts may damage this unit internally or may not securely install
the unit in place. This may cause parts to become loose resulting in hazards or product failure.
DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST. Avoid installing the unit in locations
with high incidence of moisture or dust. Moisture or dust that penetrates into this unit may result in product
failure.
HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS. The wiring and installation of this unit
requires special technical skill and experience. To ensure safety, always contact the dealer where you
purchased this product to have the work done.
HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage
to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for repairing.
Operation
Main power indicator
PWR
UP
DN
SEL
DISP
Remote control sensor
(The remote control is
sold separately)
NOTE: Controllable with Remote Control
This unit can be controlled with an optional Alpine remote control. For details, consult your Alpine dealer. Point
the optional remote control transmitter at the remote control sensor.
Screen Display ON/OFF
1. Press the PWR button.
2. To turn off the POWER, press the PWR button again.
Note:
If properly connected, the monitors main POWER will turn off when the vehicle’s
ignition switch is off. If the main power lamp illuminates in the STAND BY mode, the
vehicle’s battery may be discharged.
Adjusting the Volume
1. Adjust the volume level by pressing the
DN or
UP button.
Switching NTSC/PAL
Switch the movie output type NTSC/PAL in AUX mode.
1. Press the DISP button for at least 1 second.
Note: When the movie output type is not compatible, the movie does not output
normally.
Switching the source
1. Press the SEL button. Each press of the button will cycle through the modes as
follows:
AUX
NAVIGATION
Switching the display mode.
1. Press the DISP button.
Each press of the button will cycle through the modes as follows:
CINEMA
NORMAL
WIDE
ZOOM
WIDE: Normal images are expanded uniformly in the horizontal direction and are
displayed over the entire screen.
CINEMA: Normal images are expanded in the horizontal and vertical directions.
The top and bottom of the image is cut off. This mode is suited for 16:9 cinema size
images.
ZOOM: Normal images are expanded in the horizontal direction and are displayed
over the entire screen. The expansion ratio increases towards the right and left
edges of the screen.
NORMAL: Normal image (4:3)
Page 4
Operation
Reset the Monitor Settings
1. Press and hold the PWR button for at least 1 second.
2. Press the SEL button.
3. Select the Navigation system by pressing the DN or UP button.
: Standard - Navigation for all others (except Europe)
: Europe - Navigation for Europe only
If no key is pressed within 10 seconds, the On-Screen Display wil turn off.
Adjustment
1. Press and hold the SEL button for at least 1 second.
2. Each press of the button will cycle through the modes as follows:
DIM.
LEVEL
COLOR
BRIGHT
TINT
DIMMER
MIRROR
MONITOR
3. Adjust by pressing the
DN or
UP button.
• BRIGHT: Allows the brightness of the picture.
• COLOR: Change the color balance of the picture.
Note: It is not adjustable in NAVIGATION (RGB connection) mode.
• TINT: Adjust the tint of the picture.
Note: It is not adjustable in NAVIGATION (RGB connection) and PAL mode.
• DIMMER:
AUTO: Display illumination will dim when while the car’s parking lights are on.
LOW: Backlighting is set to the adjusted DIM.LEVEL.
HIGH: Backlighting is set to its maximum level.
• DIM.LEVEL: Adjust the backlighting level for LOW DIMMER.
• MIRROR: Switch the picture to NORMAL/MIRROR (for rear view camera) image.
4. After completing adjustments, press and hold the SEL button for at least 1 second.
If no key is pressed within 10 seconds, the OSD will turn off and any changes made
are automatically set.
Notes:
• After turning the system off, a slight ghost of the image will remain temporarily. This
is an effect peculiar to LCD technology and is normal.
• Under cold temperature conditions, the screen may lose contrast temporarily. After
a short warm-up period, it will return to normal.
• The LCD panel is manufactured using an extremely high precision manufacturing
technology. Its effective pixel ratio is over 99.99%. This means that there is a
possibility that 0.01% of the pixels could be either always ON or OFF.
Page 5
In Case of Difficulty
If you encounter a problem, please review the items in the
following check list. This guide will help you isolate the problem
if the unit is at fault. Otherwise, make sure the rest of your
system is properly connected or consult your authorized Alpine
dealer.
Symptom
No function or
display.
Cause
Solution
Car's ignition is off.
Turn the ignition on.
No fuse or blown fuse.
Check the cause and replace the fuse.
Check connection and remedy.
Incorrect connections.
Vehicle's battery is weak.
Fluorescent tube is exhausted.
Check the voltage of vehicle's battery.
Replace the fluorescent tube*.
Unclear picture
display.
No picture
display.
Brightness control is set for
minimum brightness control.
Adjust the brightness.
Incorrect setting of the Input mode.
Protective circuit is on because of
high temperature.
Switch to the correct mode.
Wait until the temperature inside the vehicle comes down to the
operating temperature range (45°C).
Incorrect or open connection with
the Monitor, AV Interface unit.
Brightness/Color/Tint control are not
set to the proper positions.
Check the connection and remedy.
Picture color is
poor.
Check each control.
Spots or dotted
lines/stripes
appear.
Caused by neon signs, high-voltage
power lines, CB transmitter, other
vehicle's ignition plugs, etc.
Change the location of your vehicle.
Unit does not
operate.
Monitor's power is not turned on.
Turn on the monitor's power.
Navigation
Navigation system’s power is turned
off.
Press the ON/OFF (POWER) button on the navigation system’s
remote controller to turn the navigation system’s power on.
screen is not
displayed or
navigation
system’s remote
controller keys do
not work.
* Replacement of the fluorescent tube is not covered under the
warranty. This is a consumable part subject to wear during
normal usage.
Page 6
Installation
Caution:
Do not install the monitor near the front passenger seat air bag system.
<Mount it using the supplied bracket>
1. Assemble the supplied bracket and mount the monitor temporarily.
Note: Always use the supplied bracket or equivalent.
1
2. Verify the installation location.
Select a flat surface and temporarily mount the unit. Use adhesive
tape, etc.
Notes:
• Mounting hints
• Top of the monitor should not exceed the top of the dash when
viewed from the driver’s seat.
• Use a stable mounting surface.
• Angle the monitor for easy viewing.
• In a vehicle with a front passenger air bag, do not install the unit
where it will interfere with the operation of the safety systems.
• If the surface of the dash board is finished with other than plastic
(leather, wooden panel, cloth covered panel, etc.), there will be
some damage if the bracket is removed.
2
• Installation close to other equipment (such as a GPS antenna) may
give rise to mutual interference. Please pay careful attention to the
installation location and maintain sufficient space between other
equipment.
3. Remove the monitor from the bracket.
4. Peel the protective paper from the double-stick tape on the bracket’s
base.
Clean the mounting location with a suitable cleaner.
Notes:
• Warm the mounting location with a dryer, etc. and then place the
bracket into position.
• Do not apply force or moisture for 24 hours after installation.
• If the bracket is not attached securely with just the tape, use the
supplied screws to complete the installation.
• If the mounted surface is curved slightly, reform the base to fit to its
shape.
5. Mount the monitor to the bracket.
5
Thread the mounting screw into hole at the bottom of the monitor.
Secure the monitor by tightening the screw. Depending upon the
location, the bracket can also be mounted using the supplied nut to
slide into the back of the monitor. Thread the bracket mounting screw
into the nut. Slide the nut in the channel on the back of the monitor
and adjust the height and tighten.
Dress the monitor’s cable using the cord clamp provided.
6. Adjust the height and angle of the monitor for easy visibility.
Determine the height and angle. Tighten the height and angle
adjusting screws to secure the monitor.
NOTE:
•
The A/V Interface box may be mounted in any suitable location. Make sure the box and the wires
connected to it will not interfere with safely operating the vehicle.
•
•
Mounting the Interface box near the monitor will reduce the need for additional cable extensions.
This monitor can be mounted in a headrest if desired. A special mounting kit is required and can be
purchased from your Authorized Alpine dealer. Ask for model KTE-580V.
Page 7
Connections
p
Cautions
Make connections correctly.
Improper connections may cause a fire or operation
failure.
5
e
q
w
1
Ground lead (Black)
Connect the lead to a good chassis ground on the
vehicle. Make sure the connection is made to bare
metal and is securely fastened using the sheet metal
screw provided.
r
2
3
No Connection
ACC power lead (Red)
To ACC power lead powered when engine key
position is ACC.
6
Battery
q
t
4
5
No Connection
Foot brake lead (Yellow/Black)
Connect this lead to the foot brake lead powered
when the foot brake is pressed.
Hand brake lead (Yellow/Blue)
Connect this lead to the hand brake lead powered
when the hand brake is pulled.
y
Chassis
6
7
8
Dimmer (White/Blue)
To the Parking Light switch. Backlighting will dim
when lights are turned on at night.
Remote control output lead (White/Brown)
To remote control input lead of ALPINE products used
in the system.
8
For the North American Customers only
7
p
q
w
e
r
Foot brake lamp
Brake connector
Foot brake lead
Foot brake switch
Hand (parking) brake lamp
Hand (parking) brake lead
Hand (parking) brake switch
3
1
t
y
Specifications
MONITOR
Screen Size ......................................................................................................................................... 5.8-type
Display System ...................................................... Low reflection rear projection type TN liquid crystal panel
Drive System .................................................................................. Active matrix drive, normally white display
Number of Picture Elements .................................................................... 280,800 pcs. (H:1200 x V:234 dots)
Effective Number of Picture Elements .................................................................................... 99.99% or more
Light Source ................................................... Internal optical system (U-type cold cathode fluorescent tube)
Dimensions (W x H x D) ........................................................... 160 x 93 x 27 mm (6.30 x 3.66 x 1.06 inches)
Weight ....................................................................................................................................... 298g (10.5 oz)
AV Interface Unit
Dimensions (W x H x D) ............................................................. 72 x 60 x 24 mm (2.84 x 2.36 x 0.95 inches)
Weight ....................................................................................................................................... 128 g (4.5 oz.)
Note: Due to continuous product improvement, specifications and design are subject to change without notice.
SERVICE CARE
• For European Customers
Should you have any questions about warranty, please consult your authorized Alpine Dealer.
• For Customers in other Countries
IMPORTANT NOTICE
Customers who purchase the product with which this notice is packaged, and who make this purchase in countries other than
the United States of America and Canada, please contact your dealer for information regarding warranty coverage.
Page 8
TME-M580 + Video and Navigation
Power Harness Color Code
1
2
3
4
5
6
7
8
Ground
Black
NOT USED
Accessory
OPEN
3 pin EXT.PWR Cord
Red
NOT USED
Foot Brake (+)
Parking Brake (-)
Dimmer (+)
IR Remote
OPEN
This cord is only used when using this
monitor as a navigation monitor only.
Yellow/Black
Yellow/Blue
White/Blue
White/Brown
POWER
MIC/SW TD DISP.
EX-1
EX-2
White Brown
GPS ANT.
1
5
10
6
V
I
D
E
O
13 Pin Nav Cable
(included with Alpine
Navigation systems)
Ext Box Front side
Ext Box Back side
8 Pin Power
Harness
8 Pin to
Monitor
TO BRAIN
TO NAV
NOT USED
8 Pin Din to
Monitor Brain
3 Pin EXT
(if running
nav only)
13 Pin Nav
Cable to
Alpine Navigation
Page 9
TME-M580 + Navigation Only
Power Harness Color Code
1
2
3
4
5
6
7
8
Ground
Black
NOT USED
Accessory
OPEN
Red
NOT USED
Foot Brake (+)
Parking Brake (-)
Dimmer (+)
IR Remote
OPEN
Yellow/Black
Yellow/Blue
White/Blue
White/Brown
POWER
MIC/SW TD DISP.
EX-1
EX-2
GPS ANT.
5
1
10
6
13 Pin Nav Cable
(included with Alpine
Navigation systems)
Ext Box Front side
Ext Box Back side
8 Pin Power
Harness
8 Pin to
Monitor
NOT USED
TO NAV
TO BRAIN
NOTE:
8 Pin Din to
Monitor Brain
3 Pin EXT
(if running
nav only)
13 Pin Nav
Cable to
Alpine Navigation
Please use the tape included to tie
both cables together to ensure the
cable will not come loose from the
monitor.
Page 10
TME-M580 + Video Only
Power Harness Color Code
1
2
3
4
5
6
7
8
Ground
Black
NOT USED
Accessory
OPEN
Red
NOT USED
Foot Brake (+)
Parking Brake (-)
Dimmer (+)
IR Remote
OPEN
Yellow/Black
Yellow/Blue
White/Blue
White/Brown
3 pin EXT.PWR Cord
White Brown
This cord is only used when using this
monitor as a navigation monitor only.
V
I
D
E
O
EXT Box Front side
EXT Box Back side
8 Pin Power
Harness
8 Pin to
Monitor
TO BRAIN
NOT USED
NOT USED
8 Pin Din to
Monitor Brain
3 Pin EXT
(if running
nav only)
13 Pin Nav
Cable to
Alpine Navigation
Page 11
/////alpine®
ALPINE ELECTRONICS, INC.
Tokyo office: 1-1-8 Nishi Gotanda,
Shinagawa-ku, Tokyo 141-8501, Japan
Tel.: (03) 3494-1101
ALPINE ITALIA S.p.A.
Viale C. Colombo 8,
20090 Trezzano Sul Naviglio (MI), Italy
Tel.: 02-48 47 81
ALPINE ELECTRONICS OF AMERICA, INC.
19145 Gramercy Place, Torrance,
California 90501, U.S.A.
ALPINE ELECTRONICS FRANCE
S.A.R.L.
(RCS PONTOISE B 338 101 280)
98, Rue de la Belle Etoile, Z.I. Paris
Nord II, B.P. 50016, 95945, Roissy
Charles de Gaulle Cedex, France
Tel.: 01-48 63 89 89
Tel.:1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF CANADA, INC.
7300 Warden Ave., Suite 203, Markham,
Ontario L3R 9Z6, Canada
ALPINE ELECTRONICS OF U. K., LTD.
13 Tanners Drive, Blakelands,
Milton Keynes MK14 5BU, U.K.
Tel.: 01908-61 15 56
Tel.:1-800-ALPINE-1 (1-800-257-4631)
ALPINE ELECTRONICS OF AUSTRALIA PTY. LTD.
6-8 Fiveways Boulevarde Keysborough,
Victoria 3173, Australia
ALPINE ELECTRONICS DE ESPAÑA,
S.A.
Portal de Gamarra 36, Pabellón, 32
01013 Vitoria (Alava) - APDO 133,
Spain
Tel.: (03) 9769-0000
ALPINE ELECTRONICS GmbH
Kreuzerkamp 7, 40878 Ratingen,
Germany
Tel.: 945-283588
Tel.: 02102-45 50
|