1
A2BC
D3EF
by
MVP Quik-Code
GHI
4
JKL
5
M6NO
P7RS
TU8V
WXY
9
0
#
*
Wireless Keyless Entry
ON
RESET
Installation Instructions
Model 110927
Proper installation of your radio controls will assure years of
trouble-free operation
READ THE FOLLOWING INSTRUCTIONS THOROUGHLY
BEFORE STARTING INSTALLATION
Your MVP Quik-Code Wireless Keyless Entry is designed to remotely operate
MVP garage door openers. The system permits the user to select one of 10,000
personal identification numbers (PIN’s) and operate multiple doors by using
different PIN’s. The radio frequency of the remote controls is fixed and tuned at
the factory; adjustments are not required and should not be attempted by the end
user.
WARNING
Features of the Quik-Code Wireless Keyless Entry
On/Reset Key: This key turns on the keypad and light system allowing you to
operated the system as well as to see the keys in the dark. The keypad will
remain lit for 20 seconds after the last key is pressed.
Single Button Mode: Once you have entered a valid PIN and your door
operator begins to function, the number keys remain active for 20 seconds.
Pressing any one of these keys sends another signal to the operator and allows
you to stop and start the door operator.
Low Battery Indicator: The lighting for your keypad also serves as a low
battery indicator. When the keypad lights flash on and off the battery should be
replaced with a standard 9 volt battery.
Non-Volatile Memory: It is not necessary to reprogram the keypad after you
replace your battery.
Allstar MVP Quik-CodeTransmitters and Receivers are
compatible with HomeLink®.
HomeLink® is a registered trade mark of Johnson Controls.
Programming Steps for Quik-Code Wireless Keyless Entry
Step 1: The red Keypad lighting should be Off. If it is
on, wait until it turns off (approximately 20 seconds).
Step 2: Using the end of a paper clip, put the receiver of
the MVP Into Learn Mode by pressing and quickly
releasing the recessed learn button located on the super
deluxe wall station. The work-lamp on the MVP will
turn on (or blink off then on) to indicate the receiver is
ready to learn a code. You have approximately 30
Learn
Button
seconds to enter the keypad PIN and door code.
Step 3: Press ON/RESET to turn on the keypad. The
red lighting on the keypad will turn on.
Super Deluxe
Wall Station
Step 4: Enter your Four Digit PIN. Every time you
press a key the keypad lighting system will blink off and
on to verify a key has been pressed.
Step 5: The work-lamp on the MVP will turn off when a valid PIN has been learned.
For example, once the MVP is in learn mode you
press the following keys: ON/RESET 6 9 7 3.
Using the Quik-Code Wireless Keyless Entry
To operate the keypad press the RESET/ON, enter your PIN. If you make a
mistake while entering your PIN press the RESET/ON and wait about 2 seconds
and enter the correct PIN. The numbered keys will remain active for
approximately 20 seconds after the door starts to move. Pressing any one of the
numbered keys during this time will allow you to stop and restart the door’s
movement.
For example, press the following keys: ON/RESET 6 9 7 3.
Changing the Quik-Code Wireless Keyless Entry PIN
To change the PIN, follow the programming steps listed above. This will overwrite
the old PIN and replace it with the new PIN.
If the MVP receiver has already learned 8 different transmitter codes and a PIN
from two different keypads, when you press and release the learn button on the
super deluxe wall station the work-lamp on the MVP will start to blink. The MVP
receiver memory must be erased before a new PIN can be learned. Once the
memory is erased a new PIN can be learned. However, erasing the memory also
erases the all of the learned MVP transmitter codes. Once erased, all the
transmitters must be re-learned before they will operate the door. To erase the
transmitter codes and WKE PINs, while the work-lamp is blinking, press and hold
the learn button until the work-lamp turns off (approximately 5 seconds). When
the work-lamp turns off, immediately release the program button. If you do not
want to continue with the erase function, quickly press and release the learn button.
To re-learn the transmitter codes, press and quickly release the learn button on the
super deluxe wall station. The work-lamp on the MVP will turn on (or blink off
then on) to indicate the receiver is ready to learn the transmitter code. Press the
button you want the receiver to learn. The work-lamp will turn off when a valid
transmitter code has been learned. To learn a new PIN, follow the directions above.
Operational Check
After installing your keypad, check the operation by entering your PIN and door
number. Operation should be reliable. However, environmental conditions and the
location of the keypad will affect distance.
• If the keypad doesn’t activate the operator check the PIN number. The PIN
number entered must exactly match the learned PIN number.
• Press the ON/RESET button and wait a few seconds before entering your PIN
number. Press the keys slowly but avoid holding the buttons down for an
extended period of time.
• If the distance is inadequate check the battery and replace if necessary.
• To maximize the operating distance move the keypad to different locations
until a satisfactory distance is achieved. Metal siding, metal doors and some
types of construction will affect distance.
• If system does not work at any distance, check that the MVP operator is
properly operating from the super deluxe wall station and hand-held
transmitter.
• Try to erase and re-learn the keypad PIN numbers and hand-held transmitter
codes (see Page 3).
WARNING
Manufacturer’s Limited Warranty
Allstar warrants its radio controls to be free from defect in material and workmanship for a period of one (1) year from the
date of purchase. To obtain service, contact your dealer.
To obtain service under this warranty the buyer must obtain authorization instructions from Allstar for the return of any
goods before returning the goods. The goods must be returned with complete identification, with copy of proof-of-purchase,
freight prepaid and in accordance with Allstar’s instructions or they will not be accepted. In no event will Allstar be
responsible for goods returned without proper authorization or identification.
Goods returned to Allstar for warranty repair within the warranty period, which upon receipt by Allstar are confirmed to be
defective and covered by this limited warranty, will be repaired or replaced at Allstar’s sole option, at no cost and returned
pre-paid. Defective parts will be repaired or replaced with new or factory rebuilt parts at Allstar’s sole option.
This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage caused by improper
installation or care, vandalism or lightning, fire or excessive heat, flood or other acts of God (including, but not limited to
misuse, abuse or alterations, failure to provide reasonable and necessary maintenance), labor charges for dismantling or
reinstalling a repaired or replaced unit, or replacement batteries.
These warranties are in lieu of all other warranties, either expressed or implied. All implied warranties of merchantability
and/or fitness for a particular purpose are hereby disclaimed and excluded. Under no circumstances shall Allstar be liable for
consequential, incidental or special damages arising in connection with the use or inability to use this product. In no event
shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product
covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product.
This warranty gives you specific legal rights. Warranty effective after March 1, 2005.
Copyright © 2005 c.p.Allstar Corporation PART NUMBER 111214 REV B
|