Washer-Extractors
Pocket Hardmount
2-Speed and 3-Speed
UW35P2
UW35P3
UW60P2
UW60P3
MC010J
Para bajar una copia de estas instrucciones
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Part No. F232090R3
February 2007
Safety Information..............................................................................
Operator Safety.....................................................................................
3
Table of
Contents
Operation............................................................................................. 10
Delivery Inspection............................................................................... 10
Customer Service.................................................................................. 10
Serial Plate Location............................................................................. 10
LED Display......................................................................................... 14
Start-up ................................................................................................. 18
Opening Door ....................................................................................... 19
Loading................................................................................................. 19
Supply Dispenser.................................................................................. 19
Cycle Selection..................................................................................... 19
Cycle Execution.................................................................................... 20
Test Cycle............................................................................................. 20
Stop Routine ......................................................................................... 21
Programming ...................................................................................... 24
© Copyright 2007, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
1
Step Programming ................................................................................ 33
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
F232090
2
Safety Information
Explanation of Safety Messages
Important Safety Instructions
Precautionary statements (“DANGER,” “WARNING,”
and “CAUTION”), followed by specific instructions,
are found in this manual and on machine decals. These
precautions are intended for the personal safety of the
operator, user, servicer, and those maintaining the
machine.
WARNING
To reduce the risk of fire, electric shock,
serious injury or death to persons when
using your washer, follow these basic
precautions:
W023
DANGER
1. Read all instructions before using the washer.
DANGER indicates the presence of a
hazard that will cause severe personal
injury, death, or substantial property
damage if the danger is ignored.
2. Refer to the GROUNDING INSTRUCTIONS in
the INSTALLATION manual for the proper
grounding of the washer.
3. Do not wash textiles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, kerosene, waxes, cooking oils, dry-
cleaning solvents, or other flammable or
explosive substances as they give off vapors that
could ignite or explode.
WARNING
WARNING indicates the presence of a
hazard that can cause severe personal
injury, death, or substantial property
damage if the warning is ignored.
4. Do not add gasoline, dry-cleaning solvents, or
other flammable or explosive substances to the
wash water. These substances give off vapors that
could ignite or explode.
5. Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for two weeks or more. HYDROGEN GAS
IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a
washing machine or combination washer-dryer,
turn on all hot water faucets and let the water
flow from each for several minutes. This will
release any accumulated hydrogen gas. The gas
is flammable, do not smoke or use an open flame
during this time.
CAUTION
CAUTION indicates the presence of a
hazard that will or can cause minor
personal injury or property damage if the
caution is ignored.
Additional precautionary statements (“IMPORTANT”
and “NOTE”) are followed by specific instructions.
IMPORTANT: The word “IMPORTANT” is used
to inform the reader of specific procedures where
minor machine damage will occur if the procedure
is not followed.
6. Do not allow children to play on or in the washer.
Close supervision of children is necessary when
the washer is used near children. This is a safety
rule for all appliances.
NOTE: The word “NOTE” is used to communicate
installation, operation, maintenance or servicing
information that is important but not hazard
related.
7. Before the washer is removed from service or
discarded, remove the door to the washing
compartment.
8. Do not reach into the washer if the wash drum is
moving.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
3
Safety Information
9. Do not install or store the washer where it will be
exposed to water and/or weather.
20. Replace worn power cords and/or loose plugs.
21. Be sure water connections have a shut-off valve
and that fill hose connections are tight. CLOSE
the shut-off valves at the end of each wash day.
10. Do not tamper with the controls.
11. Do not repair or replace any part of the washer, or
attempt any servicing unless specifically
recommended in the user-maintenance
instructions or in published user-repair
instructions that the user understands and has the
skills to carry out.
22. Loading door MUST BE CLOSED any time the
washer is to fill, tumble or spin. DO NOT bypass
the loading door switch by permitting the washer
to operate with the loading door open.
23. Always read and follow manufacturer’s
instructions on packages of laundry and cleaning
aids. Heed all warnings or precautions. To reduce
the risk of poisoning or chemical burns, keep
them out of the reach of children at all times
(preferably in a locked cabinet).
12. To reduce the risk of an electric shock or fire, DO
NOT use an extension cord or an adapter to
connect the washer to the electrical power
source.
13. Use washer only for its intended purpose,
washing textiles.
24. Always follow the fabric care instructions
supplied by the textile manufacturer.
14. Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
25. Never operate the washer with any guards and/or
panels removed.
15. ALWAYS disconnect the washer from electrical
supply before attempting any service. Disconnect
the power cord by grasping the plug, not the cord.
26. DO NOT operate the washer with missing or
broken parts.
27. DO NOT bypass any safety devices.
16. Install the washer according to the
28. Failure to install, maintain, and/or operate this
washer according to the manufacturer’s
INSTALLATION INSTRUCTIONS. All
connections for water, drain, electrical power and
grounding must comply with local codes and be
made by licensed personnel when required.
instructions may result in conditions which can
produce bodily injury and/or property damage.
NOTE: The WARNINGS and IMPORTANT
SAFETY INSTRUCTIONS appearing in this
manual are not meant to cover all possible
conditions and situations that may occur. Common
sense, caution and care must be exercised when
installing, maintaining, or operating the washer.
17. To reduce the risk of fire, textiles which have
traces of any flammable substances such as
vegetable oil, cooking oil, machine oil,
flammable chemicals, thinner, etc., or anything
containing wax or chemicals such as in mops and
cleaning cloths, must not be put into the washer.
These flammable substances may cause the
fabric to catch on fire by itself.
Any problems or conditions not understood should be
reported to the dealer, distributor, service agent or the
manufacturer.
18. Do not use fabric softeners or products to
eliminate static unless recommended by the
manufacturer of the fabric softener or product.
19. Keep washer in good condition. Bumping or
dropping the washer can damage safety features.
If this occurs, have washer checked by a
qualified service person.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
4
Safety Information
WARNING
CAUTION
This machine must be installed, adjusted,
and serviced by qualified electrical
Be careful around the open door,
particularly when loading from a level
below the door. Impact with door edges
can cause personal injury.
maintenance personnel familiar with the
construction and operation of this type of
machinery. They must also be familiar
with the potential hazards involved.
Failure to observe this warning may result
in personal injury and/or equipment
SW025
WARNING
damage, and may void the warranty.
Never touch internal or external steam
pipes, connections, or components.
These surfaces can be extremely hot and
will cause severe burns. The steam must
be turned off and the pipe, connections,
and components allowed to cool before
SW004
CAUTION
Ensure that the machine is installed on a
level floor of sufficient strength and that
the recommended clearances for
the pipe can be touched.
SW014
inspection and maintenance are provided.
Never allow the inspection and
Safety Decals
maintenance space to be blocked.
Safety decals appear at crucial locations on the
machine. Failure to maintain legible safety decals
could result in injury to the operator or service
technician.
SW020
MA004G
Figure 1
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
5
Safety Information
Key To Symbols
This warning symbol indicates the presence of
possibly dangerous chemicals. Proper precautions
should be taken when handling corrosive or caustic
materials.
The lightning flash and arrowhead within the triangle
is a warning sign indicating the presence of dangerous
voltage.
This warning symbol indicates the presence of hot
surfaces that could cause serious burns. Stainless steel
and steam lines can become extremely hot and should
not be touched.
The exclamation point within the triangle is a warning
sign indicating important instructions concerning the
machine and possibly dangerous conditions.
This warning symbol indicates the presence of
potentially dangerous drive mechanisms within the
machine. Guards should always be in place when the
machine is in operation.
This warning symbol indicates the presence of
possibly dangerous pinch-points. Moving mechanical
parts can crush and/or sever body parts.
To provide personal safety and keep the machine in
proper working order, follow all maintenance and
safety procedures presented in this manual. If
questions regarding safety arise, contact the factory
immediately.
Use factory-authorized spare parts to avoid safety
hazards.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
6
Safety Information
Operator Safety
Safe Operating Environment
Safe operation requires an appropriate operating
environment for both the operator and the machine. If
questions regarding safety arise, contact the factory
immediately.
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
Environmental Conditions
SW012
●
Ambient Temperature. Water in the machine
will freeze at temperatures of
32° F or below.
To ensure the safety of machine operators, the
following maintenance checks must be performed
daily:
Temperatures above 120° F (50° C) will result in
more frequent motor overheating and, in some
cases, malfunction or premature damage to solid
state devices that are used in some models.
Special cooling devices may be necessary.
1. Prior to operating the machine, verify that all
warning signs are present and legible. Missing or
illegible signs must be replaced immediately.
Make certain that spares are available.
2. Check door interlock before starting operation of
the machine:
Water pressure switches are affected by increases
and decreases in temperature. Every 25° F (10°
C) change in temperature will have a 1% effect
on the water level.
a. Attempt to start the machine with the door
open. The machine should not start with the
door open.
●
Humidity. Relative humidity above 90% may
cause the machine’s electronics or motors to
malfunction or may trip the ground fault
interrupter. Corrosion problems may occur on
some metal components in the machine.
b. Close the door without locking it and attempt
to start the machine. The machine should not
start with the door unlocked.
c. Close and lock the door and start a cycle.
Attempt to open the door while the cycle is in
progress. The door should not open.
If the relative humidity is below 30%, belts and
rubber hoses may eventually develop dry rot.
This condition can result in hose leaks, which
may cause safety hazards external to the machine
in conjunction with adjacent electrical
equipment.
If the door lock and interlock are not functioning
properly, call a service technician.
3. Do not attempt to operate the machine if any of
the following conditions are present:
●
●
●
Ventilation. The need for make-up air openings
for such laundry room accessories as dryers,
ironers, water heaters, etc., must be evaluated
periodically. Louvers, screens, or other
separating devices may reduce the available air
opening significantly.
a. The door does not remain securely locked
during the entire cycle.
b. Excessively high water level is evident.
c. Machine is not connected to a properly
grounded circuit.
Elevation. If the machine is to be operated at
elevations of over 3,280 feet (1,000 meters)
above sea level, pay special attention to water
levels and electronic settings (particularly
temperature) or desired results may not be
achieved.
Do not bypass any safety devices in the machine.
WARNING
Never operate the machine with a
Chemicals. Keep stainless steel surfaces free of
chemical residues.
bypassed or disconnected balance
system. Operating the machine with
severe out-of-balance loads could result
in personal injury and serious equipment
damage.
SW039
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
7
Safety Information
●
Steam Heat (Optional) Pressure. Best
performance will be realized if steam is provided
at a pressure of 30–80 psi (2.0–5.4 bar). Steam
pressure higher than 125 psi (8.5 bar) may result
in damage to steam components and may cause
personal injury.
WARNING
Do not place volatile or flammable fluids
in any machine. Do not clean the machine
with volatile or flammable fluids such as
acetone, lacquer thinners, enamel
For machines equipped with optional steam heat,
install piping in accordance with approved
commercial steam practices. Failure to install the
supplied steam filter may void the warranty.
reducers, carbon tetrachloride, gasoline,
benzene, naptha, etc. Doing so could
result in serious personal injury and/or
damage to the machine.
SW002
●
●
Compressed Air. For machines requiring
compressed air service, best performance will be
realized if air is provided at a pressure of 80–100
psi (5.4–6.7 bar).
●
Water Damage. Do not spray the machine with
water. Short circuiting and serious damage may
result. Repair immediately
all seepage due to worn or damaged
gaskets, etc.
Drainage System. Provide drain lines or
troughs large enough to accommodate the total
number of gallons that could be dumped if all
machines on the site drained at the same time
from the highest attainable level. If troughs are
used, they should be covered to support light foot
traffic.
Machine Location
●
Foundation. The concrete floor must be of
sufficient strength and thickness to handle the
floor loads generated by the high extract speeds
of the machine.
●
Power. For personal safety and for proper
operation, the machine must be grounded in
accordance with state and local codes. The
ground connection must be to a proven earth
ground, not to conduit or water pipes. Do not use
fuses in place of the circuit breaker. An easy-
access cutoff switch should also be provided.
●
Service/Maintenance Space. Provide
sufficient space to allow comfortable
performance of service procedures and routine
preventive maintenance.
This is especially important in connection with
machines equipped with an AC inverter drive.
Consult installation instructions for specific details.
WARNING
Dangerous voltages are present in the
electrical control box(es) and at the motor
terminals. Only qualified personnel
familiar with electrical test procedures,
test equipment, and safety precautions
should attempt adjustments and
CAUTION
Replace all panels that are removed to
perform service and maintenance
procedures. Do not operate the machine
with missing guards or with broken or
missing parts. Do not bypass any safety
troubleshooting. Disconnect power from
the machine before removing the control
box cover, and before attempting any
devices.
SW019
service procedures.
SW005
Input and Output Services
●
Water Pressure. Best performance will be
realized if water is provided at a pressure of
30–85 psi (2.0–5.7 bar). Although the machine
will function properly at lower pressure,
increased fill times will occur. Water pressure
higher than 100 psi (6.7 bar) may result in
damage to machine plumbing. Component
failure(s) and personal injury could result.
Always disconnect power and water supplies before a
service technician performs any service procedure.
Where applicable, steam and/or compressed air
supplies should also be disconnected before service is
performed.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
8
Safety Information
Misuse
Never use this machine for any purpose other than
washing fabric.
●
●
Never wash petroleum-soaked rags in the
machine. This could result in an explosion.
Never wash machine parts or automotive parts in
the machine. This could result in serious damage
to the basket.
●
Never allow children to play on or around this
machine. Death or serious injury can result if
children become trapped in the machine. Do not
leave children unattended while the machine
door is open. These cautions apply to animals as
well.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
9
Operation
Operation
This manual is designed as a guide to operating and
programming the UW35P and UW60P 2-speed and
3-speed rigid-mount washer-extractor equipped with
the WE-6 microcomputer.
The UWP washer-extractor features programmable
custom cycles and high
Delivery Inspection
Upon delivery, visually inspect crate, protective cover,
and unit for any visible shipping damage. If the crate,
protective cover, or unit are damaged or signs of
possible damage are evident, have the carrier note the
condition on the shipping papers before the shipping
receipt is signed, or advise the carrier of the condition
as soon as it is discovered.
extract force.
The manuals, installation instructions, and wiring
diagrams which accompany the washer-extractor have
been included with the machine at no charge.
Remove the crate and protective cover as soon after
delivery as possible. If any damage is discovered upon
removal of the crate and/or protective cover, advise the
carrier and file a written claim immediately.
Additional copies are available at a nominal charge.
NOTE: Read this manual thoroughly before
attempting to operate the machine or program the
microcomputer.
Customer Service
NOTE: Do not use this manual in conjunction with
earlier model microcomputer-controlled UW
washer-extractors. Do not use technical literature
intended for earlier models when operating this
machine.
If literature or replacement parts are required, contact
the source from whom the washer-extractor was
purchased or contact Alliance Laundry Systems at
(920) 748-3950 for the name and address of the
nearest authorized parts distributor.
For technical assistance, call:
NOTE: All information, illustrations, and
specifications contained in this manual are based
on the latest product information available at the
time of printing. We reserve the right to make
changes at any time without notice.
(920) 748-3121
Ripon, Wisconsin
Serial Plate Location
A record of each machine is on file with the
manufacturer. Always provide the machine’s serial
number and model number when ordering parts or
when seeking technical assistance.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
10
Operation
Model Number Familiarization Guide
Sample Model Number: UW60P2OU70001
Model Number Prefix
UW
60
P
Washer-Extractor Capacity (pounds dry weight)
Type of Electrical Control
P = WE-6 Computer
Washer-Extractor Speed Capabilities
Electrical Characteristics
2 = 2 Speeds; 3 = 3 Speeds
2
O
Design Series
U7
0001
Option Identification (varies from machine to machine)
UW60P2OU70001
00000000000
220-240
11
30
60
3
3
60
27
465
500000
PHM549N
SAMPLE DECAL
Figure 2
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
11
Operation
Machine Familiarization Guide
The machine familiarization guide in Figure 3
identifies major operational features of the UWP
washer/extractor.
Emergency Stop Button
Supply Valve Box
Control Module
Supply Dispenser
Door Latch Handle
Door Handle
Door Box
Spray Rinse Tube
Door Hinge
Door Latch
Extension Arm
Shell Front
Rub Rail
Door Latch
Side Panel
FA001G
Figure 3
access to the control module. This module contains the
WE-6 microcomputer, contactors, water-level switch,
and other control components.
Theory Of Operation
The design of the washer-extractor emphasizes
performance reliability and long service life. The
cylinder, shell, and main body panels are fabricated of
stainless steel.
One dual-speed motor drives the cylinder via a V-belt
drive in both speeds for the 2-speed models. Two
motors drive the cylinder for the 3-speed models. The
UW35 uses two ball bearings held in place by a single
cast-iron housing that is bolted to the A-frame. The
UW60 uses two flange-mounted, spherical roller
bearings bolted to the A-frame.
Electrical controls for the washer-extractor are housed
in a separate enclosure located on the top of the
machine. Removing the screws from the module
cover, lifting the cover, and pulling to the rear provides
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
12
Operation
The cylinder is constructed with lifters or ribs that lift
the laundry from the bath solution when the cylinder
rotates at slow speed and then allow the laundry to
tumble back into the bath. This mechanical action
accomplishes the washing function. The cylinder is
perforated, allowing the water to drain from within
during the wash and extract steps.
The UW60 shaft seal assembly includes a brass collar
held in place on the cylinder shaft with set screws. The
collar has a flange with a ceramic ring which makes
contact with a spring-loaded phenolic face seal
enclosed in a nylon housing mounted on the rear of the
shell. The collar contains two internal O rings which
maintain contact with the cylinder shaft.
The spray rinse feature consists of a fiber-reinforced
clear hose connected to the center of the door glass and
to both a hot and cold water inlet valve. A
hemispherically-shaped spray nozzle inside the door
glass produces a fan-action water spray which
disperses rinse water throughout the load.
The polypropylene supply dispenser is mounted on the
right side of the washer-extractor, viewed from the
front. The dispenser has five supply compartments,
numbered 1–5, starting from the rear of the machine.
The compartments hold plastic supply cups that are
used for either liquid or dry supplies. A nozzle flushes
supplies from the cups with water for the time
programmed in the cycle.
The operator can select from among 39
preprogrammed cycles.
Liquid supplies can be injected directly into the cups
by a customer-supplied external chemical supply
system. Five hose strain reliefs on top of the supply
dispenser facilitate connection to an external supply
system. A terminal strip inside a compartment
attached to the left side of the control module, viewed
from the rear of the washer-extractor, provides
connection points for external supply signals.
Programmable custom cycles are another feature of
the UWP.
On the UW60, a balance switch is installed between
the faces of the A-frame to signal the controls to slow
the machine when a severely out-of-balance load
occurs during extract.
Water enters the washer-extractor through
electromechanical water valves controlled by the
microcomputer. The microcomputer also controls the
drain and the door lock. In addition, it selects the water
levels according to the programmed cycle. Vacuum
breakers are installed in the water-inlet plumbing to
prevent backflow of water.
Emergency Stop Button
A red emergency stop button is located on the upper
right-hand corner of the control panel. Push the button
in to stop the washer-extractor. Turn button to the left
and pull out to reset.
The standard production UWP uses a single drain
valve. (Dual drains are available as an option. The dual
drains open and close together under control of the
WE-6 computer.) The drain valve is normally open,
which means that it closes only when power is applied,
thus allowing the machine to drain in the event of a
power failure.
A door-lock system prevents opening of the stainless
steel door when a cycle is in progress. It also prevents
operation of the washer-extractor when the door is
open. The doorbox contains the door-lock
microswitch, door-closed magnetic switch, and the
door unlock solenoid.
The UW35 shaft seal assembly includes two lip seals
integrated into the cast-iron bearing housing. Each seal
has two lips which make contact with a polished
stainless steel bushing mounted to the shaft.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
13
Operation
WE-6 Microcomputer
LED Display
The WE-6 microcomputer control is a field-
programmable solid-state control capable of storing
and running up to 39 preprogrammed ready-to-use
cycles. A detailed description of these cycles can be
found in the Programming section of this manual
under Individual Cycle Charts. (If this machine’s
computer has been equipped with special
The WE-6 microcomputer has a six-digit LED display.
References to display indications pertain to the first
four digits of the display reading left to right. The last
two digits on the right side of the display will indicate
either the last cycle used or the current cycle in
preprogrammed cycles, a separate insert listing these
cycles has been included in the resealable plastic bag
which contained this manual.)
Step
Number
Cycle
Number
Function
Being
Executed
Never turn the power off while the computer mode
switch is in the PROGRAM position. Such action will
disorder portions of the programmed data,
necessitating reprogramming of some or all of the
existing cycles. Always return the mode switch to
RUN position before turning the power off.Never
leave the mode switch key inserted in the switch lock
where it may be accessible to unauthorized personnel
not familiar with programming procedures.
MC007A
The computer control in this washer-extractor is
continuously on the alert for problems within the
machine. When the computer detects a problem, it
immediately flashes a letter or number or both on the
display. It may activate the signal buzzer as well.
Figure 4
The table which follows, entitled “Display
Interpretations,” lists the various displays and what
they mean.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
14
Operation
Display Interpretations
Display Interpretations (Continued)
Program identification code (ROM).
This is an example only.
Hot fill to overflow
Hot rinse
HO
HR
HS
MS
HT
UWP_01
End of cycle
DONE
DOOR
EMTY
FILL
High speed spin
Medium speed spin
Heat (steam or electric)
Door not locked problem
Empty problem
Fill problem
Minutes (used when programming
time)
--M
--S
Spin coast delay
SDLY
Select cycle or open door or select
program
Seconds (used when programming
time)
NEXT
Cycle not available
Stop button pressed or cycle ended
Auxiliary output #1
Auxiliary output #2
Signal
Soak
NCYC
STOP
A1
SK
S1
S2
S3
S4
S5
Supply #1 (Detergent)
Supply #2 (Bleach)
Supply #3 (Sour)
Supply #4 (Softener)
Supply #5 (Specialty)
A2
A3
Cold flush
CF
Cold fill to high level
Cold fill to medium level
Cold fill to low level
Cold fill to overflow
Cold rinse
Controlled temperature fill to high
level
CH
CM
CL
TH
TM
Controlled temperature fill to medium
level
Controlled temperature fill to low level
Controlled temperature overflow
Wash #1 (normal reversing)
Wash #2 (gentle reversing)
TL
CO
CR
CY
TO
W1
W2
W3
Cycle number
Drain #1
D1
Wash #3 (no agitation)
Drain #2 (This feature is operational on
UWPV models only.)
D2
Wash #4 (distribution speed–forward
only)
W4
Heat select temperature in ° Fahrenheit
Heat select temperature in ° Centigrade
Hot flush
F
Wash #5 (temp.-controlled cool-down)
Warm flush
W5
WF
WH
WM
WL
C
HF
HH
HM
HL
Warm fill to high level
Warm fill to medium level
Warm fill to low level
Hot fill to high level
Hot fill to medium level
Hot fill to low level
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
15
Operation
Display Interpretations (Continued)
Warm fill to overflow level
WO
Warm rinse
WR
Left dot–poor balance condition
Second dot from left–door lock switch
Third dot from left–program mode
Fourth dot from left–high level reached
•
•
•
•
Fifth dot from left–medium level
reached
•
Right dot–low level reached
Cycle already in memory
•
EXISTS
EDIT?
TEMP
Do you want to edit the cycle?
Over-temperature-limit condition
Open or shorted temperature input
circuit or temperature out of
computer’s allowable limits
OVERHT
WATER
Water in washer-extractor at end of
cycle
Temperature in degrees Fahrenheit
Temperature in degrees Centigrade
Manual Mode enabled
°FAR
°CEN
MANUAL
NO MAN
1DRAIN
Manual Mode disabled
One drain capability selected
Second independent drain enabled via
Auxiliary 2 output. (This feature is
operational on UWPV models only.
and should not be confused with the
“dual drain” option.)
2Drain
Advance (skip steps) feature enabled
Advance feature disabled
ADV
NO ADV
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
16
Operation
Operational Keypad
The computer’s control keypad includes sixteen keys.
printed in black lettering on a silver background.
These functions are available to the operator and are
intended to control operation of the machine. See the
table below.
Operational Keypad
Description
Key
Press to select cycle number.
Numbers 0–9
Display Temp
Press and hold. Display will show and update sump temperature in degrees Fahrenheit or Centigrade.
Press to cause computer to skip to the next step in the cycle. The computer will not advance past
drain step if machine is not empty. (The Advance key is enabled at the factory and can be disabled at
the
Advance
laundry site.)
Press to immediately abort the cycle and initiate the Stop Routine.
Stop
Press to start selected cycle or to re-start a step following a “FILL” or “EMTY” alarm. See Error
Recovery Routine in this section of the manual.
Start
See Manual Mode Control Feature at the end of this section.
Manual
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
17
Operation
Located to the left of the computer keyboard are 20
LED indicator lights for the computer outputs. During
the time that a cycle is running, one or more of these
lights will be on to indicate the outputs activated for a
Program
Mode
High Level
Fill Indicator
Medium Level
Fill Indicator
Door Lock
Switch
Low Level
Fill Indicator
Balance Sensing
Indicator
MC008G
Figure 5
The display will then show “NEXT00” to indicate that
a cycle can be selected. This display will be shown at
all times that power is on between cycles, indicating
that the door-unlock solenoid will function if the door-
unlock button is pressed. The washer-extractor is then
ready for loading and unloading.
Start-up
Turn on the main power source (circuit breaker or cut-
off switch on the wall).
When AC power is turned on, the display will show
the program (ROM) identification code.
This identification code will appear for approximately
five seconds. Then the computer display will flash
“POWER” and “WAIT” alternately for 30 seconds.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
18
Operation
Opening Door
Loading
Use left hand to press and hold the door unlock button
located on the lower right front of the control panel.
Load the machine to full capacity whenever possible,
but do not exceed the rated dry-weight capacity of the
machine if the fabric to be washed is quite dense,
closely woven, and heavily soiled. Overloading can
result in an inferior wash. The operator may need to
experiment to determine load size based on fabric
content, soil content, and level of cleanliness required.
Partial loads are a waste of energy, water, and
chemicals, and cause greater machine wear than full
loads. Partial loads also increase the possibility of a
severe out-of-balance condition.
When loading is complete, ensure that all fabric is
inside the basket. Then close and lock the door.
NOTE: When washing items which may
disintegrate or fragment, such as mop heads or
sponges, use laundry nets to prevent drain
blockage.
MD003J
Supply Dispenser
Figure 6
Dry supplies are placed in the supply dispenser
compartment cups prior to the start of each cycle.
Use right hand to turn door handle clockwise and
Liquid supplies can be injected directly into the supply
dispenser by an external chemical supply system.
NOTE: Supply dispenser compartment cups must
not be removed when an external chemical
injection supply system is attached to the washer-
extractor.
Cycle Selection
NOTE: Press keys at their centers just hard enough
to activate them.
Find the cycle number of the desired wash cycle from
the preprogrammed cycle charts in the Programming
section of this manual. Cycle numbers must be two-
digit numbers from 01 to 39.
Press the numbers desired on the keyboard and note
that these numbers are displayed after “NEXT.”
MD004J
When keys are pressed on the keyboard, a beep will be
heard. If an error is made, press the numbers again. As
numbers are entered, they move from right to left on
the display.
Figure 7
NOTE: If the washer-extractor is equipped with
both steam and electric heat, the selector switch on
the right side of the control module must be in the
correct position for the desired heat source, down
for steam heat, up for electric heat.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
19
Operation
Cycle Execution
Test Cycle
To start the selected cycle, press the Start key. If the
selected cycle number is not in the computer memory,
the display will show “NCYC.” If this happens, select
another cycle. Otherwise, the display will now show
the first step. For example, if the display reads “HL0l,”
“HL” represents a hot fill to low level, and “01”
indicates that this is the first step of
Cycle number 01 is a test cycle used to analyze
washer-extractor functions. See the Programming
section of this manual.
Step 01 in cycle number 01 is a cold fill to low level.
This step is designed to give not quite enough time to
complete a fill, causing the display to read “FILL.”
Press the Start key to continue the fill, and the test
cycle will proceed.
the cycle.
As the cycle proceeds, the display will show the
function being executed, the step number, and the
cycle number selected. Pressing the Edit Cycle key
while the cycle is running will cause the display to
show the remaining cycle time in minutes. Pressing
this key again will return the display to normal.
Step 02 in the test cycle is a drain step. Again, the time
allotted is shorter than it would be in a normal cycle.
The display will read “EMTY.” To proceed, press the
Start key.
The steps in the test cycle are relatively short with the
exception of steps 3 and 21. These can be shortened by
pressing the Advance key to go on to the next step.
To begin the cycle at any step other than the first step,
press the Advance key to advance through the cycle to
the desired starting point. (The Advance key is
enabled at the factory and can be disabled at the
laundry site.) Then press the Start key.
The operator may skip to any next step in the cycle
with the exception of a drain step: Drain steps must be
allowed to complete. To skip forward in the test cycle,
press the Advance key.
It is possible to skip to the next step in a cycle, with the
exception of a drain step: Drain steps must be allowed
time to complete.
NOTE: The Advance feature may be disabled. See
Prompting the WE-6 under System Programming
in the Programming section of this manual.
When the display shows the step desired to begin the
cycle, press the Start key.
If the door is not locked, the display will indicate
“CLOSE” and “DOOR.” If this occurs, be sure the
door is closed and locked and press the Start key
again.
If the LED indicator lights for the computer outputs
indicate that one or more outputs are activated but the
washer-extractor is not functioning according to the
output or outputs indicated, contact a service
technician.
As water fills the washer-extractor, one or more of the
indicator lights located to the left of the keyboard will
come on and stay on until the required water level is
reached. LED dots located in the upper left corner of
the last three digits on the right of the display will
illuminate to indicate the water level(s) reached:
●
●
●
When the indicator dot in the last digit on the
right is lit, the low water level has been reached.
When the dot in the next-to-the-last digit is lit,
medium water level (optional) has been reached.
When the dot over the third digit from the right
has been lit, high level has been reached.
The cycle will continue until its completion. Then the
display will read “DONE.”
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
20
Operation
Stop Routine
Balance Switch Detection
The washer-extractor is equipped with a balance
switch detection system whereby the switch installed
between the faces of the A-frame signals the computer
to slow the washer-extractor when an out-of-balance
load occurs during extract.
WARNING
NEVER insert hands or objects into
basket until it has completely stopped.
Doing so could result in serious injury.
SW012
If the balance switch is tripped, the out-of-balance
LED indicator located in the upper left corner of the
first digit of the display will light and will remain
lighted until the end of the extract step. This indicator
tells the operator that an out-of-balance condition
existed during an extract step. The washer-extractor
will attempt to balance three times during an extract
step.
A lengthy stop procedure ensures that the basket has
adequate time to stop (from the machine’s highest
speed) before the computer allows the door to be
opened. This is an important safety feature.
During the normal stop routine at the end of the cycle,
the computer will display “STOP” and turn off all
outputs.
If on the third attempt the out-of-balance condition
continues, the washer-extractor will advance to the
next step. (If the next step is another spin step, it will
be skipped also.)
A 30-second shakeout (Wash 1) is included as part of
the stop procedure. If additional shakeout is desired,
see Programming a Spin Step in the Programming
section of this manual.
NOTE: This feature applies to the UW60 only.
The remainder of the stop routine is fixed at the
following:
NOTE: The computer cannot advance through a
drain step.
●
low speed forward for 15 seconds
pause for 5 seconds.
●
Temperature Display
The computer will display “DONE,” and the door can
be unlocked. The computer will continue to display
“DONE” until the operator opens the door. Once the
door is opened, the display will change to “NEXT.”
The temperature display can be prompted to display in
Fahrenheit or Centigrade. See Prompting the WE-6 in
the Programming section of this manual.
To display temperature, press the Display Temp key.
The display will read “F” or “C” and the temperature
as long as the key is pressed. The computer will update
the display automatically.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
21
Operation
Certain error conditions are considered to be non-
recoverable:
Error Recovery Routine
When the computer detects an error, it will stop
running the current step and display a message to
indicate what type of error
●
If the door opens during a cycle, the computer
will display “DOOR.” The operator must close
the door.
was found:
Then, after the computer has detected that the
door is closed, it will automatically abort the
cycle and go to the normal stop routine.
●
●
●
“FILL” indicates that the washer-extractor did
not fill within the allotted time.
“EMTY” indicates that the washer-extractor did
not drain in the allotted time.
●
“OVERHT” will be displayed when the
computer detects an open or shorted temperature
input circuit or temperatures are outside of the
washer-extractor’s allowable limits. Contact a
service technician.
“TEMP” indicates that the temperature sensor
has recognized an over-temperature-limit
condition.
●
●
“ME” indicates that the computer has detected a
problem with the cycle information. The cycle
must be edited.
Motor Thermal Overload Indicator
A small indicator lamp on the side of the control
module will light to indicate that a thermal overload
switch in the motor has shut off the AC power to the
computer board, thereby preventing damage to the
motor caused by overheating and/or an overload
condition. This feature protects and extends the life of
the motor.
“WATER” indicates that the WE-6 computer
senses low water level at the end of the stop
routine.
All outputs remain off while the message
displays, and the door cannot be unlocked.
NOTE: The WE-6 computer will not allow the door
to be opened while there is water in the washer-
extractor.
The thermal overload switch will automatically reset
itself after the excessive heat condition has subsided.
Before attempting to restart the washer-extractor,
determine the reason for the overload. The following
is a partial list of possible problems:
Each of these errors is considered to be recoverable.
The operator has two minutes to respond to the error
condition (except in the case of “WATER”). During
this time, the computer will turn the signal (buzzer)
relay on and off at the rate of one second on and one
second off to alert the operator to the error condition.
The washer-extractor may be restarted by pressing the
Enter key. Pressing the Enter key will restart the
cycle step for the originally programmed time period.
The cycle may be aborted by pressing the Clear key.
After aborting the cycle, the computer will go to the
normal stop routine. If the operator does not respond
to the error condition within the allocated two minutes,
the computer will automatically abort the cycle.
●
●
●
●
●
●
Machine not fully drained before spin
Out-of-balance condition
Low voltage
Loss of one phase on a three-phase motor
Bad bearings
Air circulation blocked to motor
Contact a service technician to correct serious
problems. Failure to take corrective action will
ultimately result in damage to the motor.
NOTE: The “TEMP” alarm can be recovered only
after the temperature falls below the alarm level.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
22
Operation
When the computer receives all these inputs within the
three-second time limit, it will enter the manual mode
for the time assigned. The computer display will flash
between “MAN230” (reflecting the time chosen in
Step 2 of the above procedure) and the current cycle
step display for four seconds.
Manual Mode Control Feature
Manual control is available only while a
preprogrammed cycle is in progress, and if manual
mode is prompted in the WE-6 programming. With the
exception of motor speeds and the door unlock output,
the WE-6 computer outputs can be operated manually
from the keypad. (In order to assure proper
sequencing, all motor speeds are always controlled by
the computer.)
NOTE: If “NO MAN” is prompted and the normal
key sequence for manual mode is entered, the
computer will display only the remaining cycle
time.
NOTE: When the manual mode control feature is
activated, the operator must supply on/off
commands for the controllable outputs. If an
output is on, it will remain on until turned off by
the operator or until the assigned time for the
manual mode expires. This can be as long as 9
minutes and 99 seconds.
After four seconds, the display will flash between
“MANUAL” and the current cycle step display for the
remainder of the assigned time.
Manual mode operation will automatically end when
the assigned time elapses. Normal program timing will
then resume from the same point in the cycle where
the manual mode was entered. To exit the manual
mode and return to normal program timing before the
assigned time elapses, press the Start key.
In normal operation, when the program mode switch is
in the RUN position, only the operations printed in
black on the keys are accessible to the operator.
All water fill and spray rinse valves, supplies, heat (if
the washer-extractor has reached low water level), and
auxiliary outputs can be manually controlled. The heat
output requires that only the Heat key be pressed. All
other outputs require that two keys be pressed. For
example, to turn on the cold fill valve, press the keys
Cold and Fill. When an output is on, pressing the
same key or keys which caused it to energize will turn
it off. Thus, to turn off the cold fill valve, press the
keys Cold and Fill once again.
During the manual mode, normal cycle timing is
suspended. When the manual mode is entered, the
operations printed in red on the keys and mentioned in
the following discussion are activated.
Entering the manual mode during a fill operation is not
recommended. This bypasses the water-level switch
inputs, and the water must be turned off manually by
the operator.
The following procedure must be accomplished within
three seconds in order to enter the manual mode:
1. Press the Manual key.
2. Then press three number keys to assign a time in
minutes and seconds to the manual mode. For
example, press key 2, key 3, and key 0 to enter
the manual mode for 2 minutes and 30 seconds.
3. Then press the Add Step key.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
23
Programming
Programming
function keys in the program mode. In each instance
Programming Keypad
(with the exception of the Warm/High key), when a
key is first pressed in a programming step, the word
printed at the top of the key applies. In most instances,
the next time the same key is pressed–even if another
key has been pressed in the interim, the word printed
on the bottom of the key applies.
All sixteen keys are used in the programming mode.
Specific functions are printed in red on the keys. The
programming mode is active only when the program
mode switch is in the PROGRAM position. (When
programming is complete, remember to return the
mode switch to the RUN position and remove the key.)
Keys 1–6 and the Auxiliary/No Reverse key are dual
Programming Keypad
Red Keys
Cold
Description
Cold is pressed when the step requires cold water.
Low is pressed for low-level fill.
Low
Hot is pressed when the step requires hot water.
Med./Fill is pressed to select medium water level.
Fill is pressed in the manual mode to operate fill valves.
Hot
Med./Fill
Warm is pressed when the step requires warm water.
High is pressed for high-level fill.
Warm
High
Erase Cycle and a two-digit cycle code number are pressed to erase a cycle from memory.
Erase Cycle
Wash
Wash is pressed when the step is a wash or dilution rinse. Then key 1, 2, 3, or 4 is pressed to choose
the type of agitation.
Flush is pressed to keep the drain open when water is added to the machine. A temperature selection
key (Hot, Cold, Warm) must be pressed before the Flush key. When Flush is programmed, water is
added through the door spray nozzle only; the basket rotates in low speed forward only.
Flush
Heat is pressed when auxiliary heat is needed. This must be followed by a specific temperature
selection, such as 165°F. The temperature must be entered; then a time assigned to reach that
temperature must be entered.
Heat
Rinse is pressed when a spin-spray rinse is desired. Before the Rinse key is pressed, a temperature
key must be pressed: Hot, Cold, or Warm. The drain will remain open, and the basket will rotate at
medium-spin speed (high speed on two-speed only machines). Water is added through the door spray
nozzle only.
Rinse
Supply is pressed when soap, bleach, or other chemicals are desired. Key 1, 2, 3, 4, or 5 must then be
pressed to indicate the specific supply dispenser being used. Combinations of these supplies can be
programmed. See Programming a Supply step.
Over is pressed when an overflow of water is desired. The drain is closed and water is added, using
fill valves only, without regard to level. Water flows out the overflow connection for the time
assigned to the step.
Supply
Over
Add Cycle is pressed to begin the process of programming a new cycle into memory.
Add Cycle
Soak
Soak is used when no agitation is desired. This follows a fill and/or supply step. The time must be
assigned in hours and minutes. (Wash 3 also provides no agitation.)
Medium Speed is pressed when a medium spin only is desired for washing delicate items not suited
for high-speed spin or when an intermediate spin is desired.
Medium
Speed
High Speed is pressed when a fast spin is desired.
High Speed
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
24
Programming
Programming Keypad (Continued)
Description
Red Keys
Edit Cycle
Edit Cycle is pressed followed by a two-digit cycle code number to display the steps of a
preprogrammed cycle. The cycle may be altered during the edit cycle procedure by deleting,
changing, or adding steps.
Add Step is pressed to add a step to an existing cycle during the edit cycle procedure.
Add Step
Clear is pressed when an error has been made in programming a step. Instead of pressing Enter as the
step is completed, press Clear to eliminate the incorrect information. (Clear should never be pressed
when displaying a cycle unless a particular step is to be eliminated or changed. See
Displaying a Cycle in Memory.)
Clear (black
on red
background)
Drain is pressed after a wash, dilution rinse, or soak step is programmed in order to remove water
from the machine. A time must be assigned that will allow the machine to reach empty. If the
computer has been prompted for two drains, press key 1 or key 2 for the desired drain valve. See
Prompting the WE-6.
Drain
Auxiliary is pressed to activate the buzzer or other auxiliary output.
No Reverse is used to rotate the basket in one direction only during a step and should be pressed just
before pressing the Enter key.
Auxiliary
No Reverse
Enter is pressed to enter programming information into the computer’s memory.
Enter
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
25
Programming
b. Press the Enter key. The display will read
Programming Tutorial
“M---S.”
The following procedure guides the programmer
through a complete cycle and allows hands-on
experience for programming cycles. The complete
cycle is listed in the Tutorial Cycle table at the end of
this section.
c. Now enter the desired time in minutes and
seconds for the supply valve to be turned on.
Thirty seconds is the recommended time.
Press key 0 for minutes. The display will read
“0M-00S.”
1. Locate the key-operated programming switch on
the left side of the control module, viewed from
the front. Insert the key and turn the switch to
PROGRAM position. The display will read
“CYC00.”
Now press key 3 and then key 0. The display
will read “0M-30S,” indicating a supply time
of thirty seconds.
8. Now press the Enter key. The display will
change to read “0339,” indicating that the
computer is ready for step 3.
2. Press the Add Cycle key. The display will read
“ACYC00.”
3. A two-digit number from 01 to 39 must be
entered. Cycle number 39 is recommended
because standard program versions use this short
cycle for performing a chemical supply setup.
9. If no other supply is required, the next step is to
choose the type of wash desired and assign it a
time. For example, one might choose a wash with
standard reversing action (Wash 1) and a time of
six minutes.
4. Press key 3, then key 9, then the Enter key. The
display will read “CYC39.”
a. Press the Wash key and then key 1. The
display will read “W10339.”
a. If the display alternately flashes “EXISTS”
and “EDIT?,” press the Clear/Stop key. The
display will return to “CYC39.”
b. Press the Enter key. The display will read
“M---S.”
b. Erase the existing cycle: Press the Erase
Cycle key. The display will show “ECYC39.”
Press key 3, then key 9, then the Enter key.
The display will read “WAIT” for a few
seconds and then “CYC39.”
c. Press key 6. The display will read “6M-00S,”
indicating a wash step of six minutes.
10. Press the Enter key. The display will read
“0439,” indicating that the computer is ready for
step 4.
c. Press the Add Cycle key. The display will
read “ACYC39.” Press key 3, then key 9, then
the Enter key. The display will show “0139.”
11. A drain step usually comes next.
a. Press the Drain key. The display will read
“D10439.” (Applications using drain 2 are not
available on 2-speed and 3-speed models.)
5. Enter the desired function for step 1. A natural
choice might be hot fill to low level.
b. Then press the Enter key. The display will
a. Press the Hot key and then the Low key. The
read “M---S.”
display will read “HL0139.”
c. Enter the maximum time desired for the
computer to allow the machine to drain to
empty. The recommended time is one minute.
Press key 1, and the display will change to
“1M-00S,” indicating a drain step of one
minute.
b. Press the Enter key. The display will read
“M---S.”
c. Now enter the desired fill time. The
recommended number of minutes is four.
Press key 4. The display will read “4M-00S.”
6. Now press the Enter key. The display will read
“0239,” indicating that the computer is ready for
step 2 of cycle 39.
NOTE: The manufacturer does not recommend
more than one minute for a drain step. If the
machine does not drain in the amount of time
programmed, the “EMTY” alarm will be
displayed.
7. A natural choice for step 2 is the addition of a
supply.
a. To add supply No. 1, press the Supply key
and then key 1. The display will read
“S10239.”
12. Press the Enter key. The display will now read
“0539,” indicating that the computer is ready for
step 5.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
26
Programming
13. A natural next step in the cycle might be a warm
rinse.
c. Enter the length of time for the supply to be
activated. In this case, thirty seconds is
adequate.
a. Press the Warm key and then the Rinse key.
The display will read “WR0539.”
Press key 0 for minutes; press key 3 and then
key 0 for seconds. The display will read “OM-
30S.”
b. Press the Enter key. The display will read
“M---S.”
18. Press the Enter key as always after programming
a time duration. The display will read “0839,”
indicating that the computer is ready for step 8.
c. Now enter the rinse duration in minutes and
seconds. A spray rinse lasting 2 1/2 minutes is
an appropriate choice.
19. For step 8, program the agitation action for the
dilution rinse.
Press key 2. The display will read “2M-00S.”
Now press key 3 and key 0. The display will
read “2M-30S.”
a. Press the Wash key and key 1 to program an
action with normal reversing. The display will
read “W10839.”
14. Press the Enter key. The display will read
“0639,” indicating that the computer is ready for
step 6.
b. Press the Enter key. The display will read
“M---S.”
15. Step 6 in the cycle might be a warm fill to high
level for a dilution rinse.
c. Enter the time for the dilution rinse (three
minutes).
NOTE: The Rinse key controls a spin-spray rinse.
However, a dilution rinse is executed the same as a
wash step without the addition of detergents.
Press key 3. The display will read “3M-00S.”
20. Press the Enter key. The display will read
“0939,” indicating that the computer is ready for
step 9.
a. Press the Warm key (key 3) twice to turn on
two hot and two cold water valves to reduce
fill time. The display will read “W-0639.”
Then press the High key (key 3). The display
will read “WH0639.”
21. The dilution rinse water must be drained.
a. Press the Drain key. The display will read
“D10939.”
b. Press the Enter key. The display will read
b. Press the Enter key. The display will read
“M---S.”
“M---S.”
c. Enter the desired time for the computer to
allow the machine to fill to high level. Five
minutes is acceptable. Press key 5. The
display will read “5M-00S.”
c. Enter the length of time the computer will
allow the machine to drain (one minute).
Press key 1. The display reads “1M-00S,”
indicating that a one-minute step has been
programmed.
NOTE: If the machine does not fill in the amount of
time programmed, the “FILL” alarm will be
displayed.
22. Press the Enter key to move to step 10 of the
cycle.
16. Press the Enter key. The display will read
23. An extract step should now be programmed.
“0739.”
a. Press the Medium Speed key. The display
will read “MS1039,” indicating a medium-
speed spin.
17. Add a sour for step 7:
a. Press the Supply key and key 3. The display
will read “S30739.”
b. Press the Enter key. The display will read
“M---S.”
b. Press the Enter key. The display will read
“M---S.”
c. Enter the length of time for the medium-speed
spin (one minute).
Press key 1. The display will read “1M-00S.”
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
27
Programming
24. Press the Enter key. The display flashes “SDLY”
27. The previous step ends the tutorial. Cycle 39,
consisting of 11 steps, has been completely
programmed.
for one second.
The display will then read “0M-00S,” allowing
the programmer to enter the time for a slow down
delay (coast).
To end the cycle, turn the program mode switch
located on the left side of the control module to
the RUN position and remove the key. The
display will then
At some point in the future–to have the basket
coast before it stops, enter the desired coast time
(up to 99 seconds). However, do not enter a time
now. That would cause a coast before a higher
spin speed (which will be the next step).
read “NEXT.”
The programmer can now select Cycle 39 and
press the Enter key to run the cycle, if desired; or
a cycle of the programmer’s own design can be
programmed.
For no coast, press the Enter key.
25. The next step is to program a high-speed spin.
Tutorial Cycle
a. Press the High Speed key once. The display
will read “HS1139.”
Step
Description
Min:sec
b. Press the Enter key. The display will read
“M---S.”
1
2
3
4
5
6
7
8
9
Hot Fill to Low Level
Supply 1
4:00
0:30
6:00
1:00
2:30
5:00
0:30
3:00
1:00
1:00
c. Enter a length of time for the high-speed spin
(six minutes). Press key 6. The display will
read “6M-00S.”
Wash 1
Drain 1
NOTE: High-speed spin is preceded automatically
by medium-speed spin for 30 seconds for
nonvariable-speed UW rigid-mount models.
Warm Spray Rinse
Warm/Warm Fill to High Level
Supply 3
26. Press the Enter key. The display will flash
“SDLY” for one second. (“SDLY” also displays
during the entire actual coastdown.) The display
will then read “0M-00S,” inviting the
Wash 1
Drain 1
programmer to enter a time for the slow-down
delay (coast). If the application requires that the
basket coast before it stops, enter the desired
coast time (30 seconds here) and press the Enter
key. If no coast is desired, press the Enter key
only. The display will read “1239.”
10 Medium Speed Spin
11 High Speed Spin
SDLY
6:00
0:30
Stop Routine
NOTE: A slow-down delay of 30 seconds minimum
should be programmed after each high-speed spin.
All the preprogrammed and optional cycles in this
manual reflect this practice.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
28
Programming
Min:sec
Programming Hints
CYCLE 00
Read the preprogrammed cycle charts (near the end of
this manual) for the cycles already programmed into
the computer to see how the cycle steps have been
ordered.
Step
Description
1
2
Use a program worksheet, such as the sample on the
next page, to write new cycles. After the worksheet is
completed, enter the program into the computer.
3
4
The computer can do only one thing at a time, so think
in terms of what the machine should do next, step by
step. This will make it simpler to write the program.
5
6
When entering the timed portion of a step (such as a
fill), use a time that is reasonable for the local
installation. If the water pressure is low or if the water
lines are smaller than desirable, increase the time
allowed. Remember that the drain needs to empty the
machine in less than one minute. Drain times of more
than one minute are not recommended.
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Except for the soak, heat, and cool-down (Wash 5)
steps, which are timed in hours and minutes, the
maximum time per step is 9 minutes and 99 seconds. If
more time is needed, add more steps to total the
complete time desired. For example, if a 15-minute
wash is desired, program a wash step for 9 minutes
and 00 seconds, immediately followed by another
wash step for 6 minutes and 00 seconds.
When a fill or addition of supplies without agitation is
desired, first program a Wash 3 step for 0 minutes and
01 seconds. Then program the fill or supply step.
When the microcomputer advances to the next step, it
will remain in the wash mode as programmed in the
previous step unless it is instructed to do otherwise.
Before attempting to program any particular function
of the WE-6 microcomputer, read the System
Programming, Cycle Programming, and Step
Programming subsections below.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
29
Programming
5. Press the Enter key. The display will read either
“D SUPP” or “L SUPP.” “D SUPP” indicates that
the WE-6 is prompted for dry supplies, in which
case only the programmed supply combination
energizes during a supply step. “L SUPP”
indicates that the WE-6 is prompted for liquid
supplies. In this case, the Auxiliary 1 output
energizes along with the programmed supply
output(s) during a supply step. In the manual
mode, “AUX 1” must be manually energized if
desired with manually selected supplies.
System Programming
Prompting the WE-6
Prompting the WE-6 allows:
●
Displaying sump temperature in Centigrade or
Fahrenheit.
●
Recognizing and controlling one or two
independent drains. (Two independent drains will
apply only for special applications.)
●
Enabling or disabling the Advance key in the
6. Press the Enter key. The display will show
“USEDxx.” (The “xx” here stands for the
number of cycles run and will be represented by
numbers in the actual display.)
RUN mode.
●
●
Enabling or disabling the manual mode.
Controlling the Auxiliary 1 output for use with
liquid supplies.
The count can be left as it appears in the display,
or it can be reset to “00.”
●
Reading or resetting the cycle count.
●
To leave the count unaltered, press the Enter
key to return to the normal programming
mode.
To begin prompting the computer, insert key into the
program mode switch (located on the left side of the
control module) and turn key to the PROGRAM
position. The display will read “CYC00.”
●
To reset the count, press key 0. The display
will read “USED00.”
1. Press the Auxiliary key, key 2, and key 9 in that
order. The display will read either “CEN”
(Centigrade) or “FAR” (Fahrenheit). To choose
the alternate feature, press key 0.
Press the Enter key to return to the normal
programming mode.
The computer stores the cycle count in RAM.
Thus, if power to the computer is interrupted, the
count will automatically be set at “00.”
2. Press the Enter key. The display will read either
“1DRAIN” or “2DRAIN.” The normal prompt
for most applications is “1DRAIN.” “2DRAIN”
is used only for special applications. Consult the
factory for full details. To choose the alternate
feature, press key 0.
If a daily count is desired, the display should be
read at the end of the day and then reset prior to
running the next day’s first cycle. (The display
resets automatically after the cycle count reaches
99.)
3. Press the Enter key. The display will read either
“ADV” or “NO ADV.” The prompt “NO ADV”
will disable the Advance key in the RUN mode,
thereby preventing the operator from advancing
the computer through steps of the cycle before
they are complete; also, it will not be possible to
advance to any step before starting a cycle if “NO
ADV” is selected. To choose the alternate
feature, press key 0.
7. Return the program mode switch to the RUN
position and remove the key. Prompting is
complete.
NOTE: Prompting will change the parameters in
all cycles programmed.
4. Press the Enter key. The display will read either
“MANUAL” or “NO MAN.” If “MANUAL” is
displayed, the manual mode will be enabled
during normal operation. If “NO MAN is
displayed, the manual mode will be disabled
when a cycle is run, even if the Manual
operation key sequence is entered. To choose the
alternate feature, press key 0.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
30
Programming
Displaying Individual Cycle Usage
Cycle Programming
1. Insert key into the program mode switch (located
on the left side of the control module) and turn
key to the PROGRAM position. The display will
read “CYC00.”
Displaying a Cycle in Memory
1. Insert key into the program mode switch (located
on the left side of the control module) and turn
key to the PROGRAM position. The display will
read “CYC00.”
2. Press the Edit Cycle key on the keypad. The
display will read “DCYC00.”
2. Press the Edit Cycle key on the keypad. The
3. Press the two-digit code to display the desired
cycle number: For example, press key 2 and then
key 5 to select cycle 25.
display will read “DCYC00.”
3. Press the two-digit code to display the desired
cycle number: For example, press key 2 and then
key 5 to select cycle 25. The display will read
“DCYC25.”
4. Press the Enter key. The display will show
“xx25.” (The “xx” here stands for the number of
times cycle 25 has been run and will be
4. Press the Enter key. The computer will search
represented by numbers in the actual display.)
for cycle information for this cycle number.
The computer will remain in this step until one of
the following options has been chosen:
If no cycle information exists, the computer will
flash “NCYC25” followed by “ADD?” To add
this cycle, press the Enter key and proceed to the
add cycle programming mode. If adding this
cycle is not desired, press the Clear key, and the
computer will then return to the normal
programming mode.
● Press the Enter key to continue displaying the
cycle, OR
● Press the Clear key to return to the normal
program mode, OR
● Press key 0 to reset the counter for this cycle
5. If cycle information does exist for cycle 25, the
computer will display “0425,” for example, to
indicate that cycle 25 has been run four times. To
clear the count (reset it to zero), press key 0. The
display will then show “0025.”
to zero, OR
● Take the computer out of the program mode.
If clearing the count is not necessary or if it has
just been cleared, press the Enter key. The
computer will now display “HL0125,” indicating
the first step of cycle 25.
6. Press the Advance key to move to the next step
of the cycle. To access further information
pertaining to each step (for example, temperature
and/or time), press the Enter key. If the display
shows a temperature, press the Enter key again
to display the time. Press the Enter key once
more to advance to the next step.
7. At the end of the cycle, the computer will display
“END-25” for two seconds and return to the
normal programming mode.
8. Return the program mode switch to the RUN
position and remove the key.
NOTE: Never press the Clear key while displaying
a cycle in memory except to edit or delete a step.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
31
Programming
11. To change a step within the cycle, press the Clear
key once while the computer is displaying the
step to be edited. Enter the new step using the
same procedure for adding a step to a new cycle.
Editing a Cycle
To edit a cycle in memory or to change, add, or delete
a step:
1. Insert key into the program mode switch (located
on the left side of the control module) and turn
key to the PROGRAM position. The display will
read “CYC00.”
NOTE: If, after the Clear key is pressed, it is
decided that clearing the step is not desired, press
the Edit Cycle key to restore the step. (This will
work only if a step identification was displayed
before pressing the Clear key. At other points in the
step–such as a time or temperature display–this
restoration effort will not work.)
2. Press the Edit Cycle key on the keypad. The
display will read “DCYC00.”
3. Press the two-digit code for the cycle requiring
editing: For example, press key 2 and then key 5
to select cycle 25.
12. To change the time assigned to a step, press the
Clear key once while the computer is displaying
the unwanted time.
4. Press the Enter key. The computer will search
for cycle information for this cycle.
13. To add a step within the cycle, press the Add
Step key. The step will be added into the cycle
after the step presently displayed.
If no cycle information exists, the computer will
flash “NCYC25” followed by “ADD?” To add
this cycle, press the Enter key and proceed to the
add cycle programming mode. If adding this
cycle is not desired, press the Clear key. The
computer will then return to the normal
programming mode.
The computer will check to see if enough cycle
memory is left in the cycle to add a step. (Each
cycle may contain up to 51 steps.)
If the cycle memory for this cycle is full, the
computer will display “CYFULL” for two
seconds and return to displaying the previous
step. If the computer sees no problem, the new
step number will be displayed and the step may
be added (as when adding a step to a new cycle).
5. If cycle information does exist for cycle 25, the
computer will display “0425,” for example, to
indicate that cycle 25 has been run four times. To
clear the count (reset it to zero), press key 0. The
display will then show “0025.”
NOTE: Use the following procedure with caution.
If clearing the count is not necessary or if it has
just been cleared, press the Enter key. The
computer will now display “HL0125,” indicating
the first step of cycle 25.
It is not reversible.
14. To delete a step within a cycle, press the Clear
key while the computer is displaying the step to
be deleted. Press the Clear key again: the display
will read “WAIT” while it is deleting the step.
6. Press the Advance key to move to the next step
of the cycle.
The computer will then display the next step in
the cycle, using the same step number as the
deleted step.
7. Press key 0 to back up to the previous step.
8. To access further information pertaining to each
step (for example, temperature and/or time),
press the Enter key.
15. If the Add Cycle key is pressed by mistake
instead of the Edit Cycle key when the cycle
number to be edited is entered, the display will
flash “EXISTS” and “EDIT?” To recover, press
the Enter key, and the computer will change to
the edit mode.
If the display shows a temperature, press the
Enter key again to display the time.
9. Press the Enter key once more to advance to the
next step.
10. At any time, the programmer can put the program
mode switch in the RUN position, and the
computer will return to normal running mode,
provided all pertinent data for the last step edited
is entered.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
32
Programming
Each time the Warm key is pressed, one hot and one
cold water valve is turned on. The machine is equipped
with four water valves (two fill and two spray); thus
pressing the Warm key twice will turn on all four
valves and reduce fill times.
Erasing a Cycle in Memory
1. Insert the key into the program mode switch
(located on the left side of the control module)
and turn the key to the PROGRAM position. The
display will read “CYC00.”
Use the following procedure to program a fill to a
specific temperature:
2. Press the Erase Cycle key. The display will read
“ECYC00.”
1. The computer must be in the PROGRAM mode,
and the cycle programming sequence must be
ready for the next step.
3. Press the two-digit code for the cycle number that
is to be erased. The display will read “ECYC25”
if cycle 25 is chosen.
2. Press the Cold key. The display will read “C.”
(HOT or WARM may be programmed instead to
control inlet valves during the first three seconds
of the fill. After the first three seconds, the fill is
the same regardless of the prompt.)
4. Press the Enter key. The display will read
“WAIT” while it is erasing the cycle. The display
will then return to “CYC00.” If there is no such
cycle number in memory, the display will read
“NCYC25.” To not erase a cycle, press the Clear
key before pressing the Enter key. The display
will return to “CYC.”
3. Press the key representing the desired water level
(Low, Medium, High, or Over). If High is
pressed, for example, the display will read “CH.”
5. Return the program mode switch to the RUN
position and remove the key.
Step Programming
Programming a Fill without Spray
This process is used in temperature-controlled fill
steps where it is desirable to fill without spray and add
water through the sump only.
To program a fill without spray, program a cold, hot,
or warm fill to level as in a normal fill step; however,
instead of pressing the Enter key after selecting the
level, press the Auxiliary key. The computer will
display a lower case “c,” “h,” or “w,” instead of the
usual upper case “C,” “H,” or “W.” Press the Enter
key now and program the time in the usual manner.
Programming a Fill Temperature
The table on the next page lists the required
procedures to produce specific results. The table
shows that when HIGH water level is programmed,
the display indicator is “H.” When MEDIUM level is
programmed, the display indicator is “M.” When
LOW level is programmed, the display indicator is
“L.” When OVERFLOW is programmed, the display
indicator is “O.”
When the Warm key is pressed, the next key pressed
will be another temperature key (Hot, Cold, or
Warm) before selecting the level. Exceptions to this
will be when RINSE or FLUSH steps are used: they
require no level commands, and water is added
through the door spray nozzle only.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
33
Programming
4. Press the Heat key. The display will read either
“080F” or “025C,” depending on whether
Fahrenheit or Centigrade is prompted.
5. Press the Enter key. The display will read
“M---S.” Now assign the maximum time to be
allowed for reaching the fill level in minutes and
seconds.
Enter the desired fill temperature. Three digits
must be entered. If the desired temperature is less
than 100 degrees, the first digit must be 0.
6. Press the Enter key, and go to the next step in the
cycle.
The valid temperature range is 80–200 degrees
Fahrenheit and 25–93 degrees Centigrade. The
computer will not accept temperatures out of this
range. (The fill temperatures possible are
governed by the temperature of the available hot
water.)
The computer will attempt to maintain the
temperature within a margin of plus or minus 5
degrees of the target fill temperature during such
a step.
Fill Temperature Programming
Keys Pressed
Hot + Low + Enter
Display
“HL”
Valves Operating
1 Hot Fill and 1 Hot Spray
1 Hot Fill and 1 Hot Spray
1 Hot Fill and 1 Hot Spray
Both Hot and Both Cold
“HM”
“HH”
“WL”
“WL”
“WL”
“CL”
Hot + Med + Enter
Hot + High + Enter
Warm + Warm + Low + Enter
Warm + Hot + Low + Enter
Warm + Cold + Low + Enter
Cold + Low + Enter
Both Hot and 1 Cold Fill
1 Hot Fill and Both Cold
1 Cold Fill and 1 Cold Spray
1 Cold Fill and 1 Cold Spray
1 Cold Fill and 1 Cold Spray
“CM”
“CH”
Cold + Med* + Enter
Cold + High + Enter
In addition to the standard fill temperatures, computer-controlled fill or overflow to a specific temperature is available.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
34
Programming
Programming a Supply Step
SUPPLY DISPLAY CODES
The WE-6 microcomputer is capable of controlling up
to 5 separate supplies and up to 31 various
combinations of the 5 supplies. (See the Supply
Display Codes Table in this subsection for a listing of
the energized supply compartments represented by
each display code.)
SUPPLY NUMBER
0 = Supply Off
X = Supply On
CODE
5 4 3 2 1
1
2
0 0 0 0 X
0 0 0 X 0
0 0 0 X X
0 0 X 0 0
0 0 X 0 X
0 0 X X 0
0 0 X X X
0 X 0 0 0
0 X 0 0 X
0 X 0 X 0
0 X 0 X X
0 X X 0 0
0 X X 0 X
0 X X X 0
0 X X X X
X 0 0 0 0
X 0 0 0 X
X 0 0 X 0
X 0 0 X X
X 0 X 0 0
X 0 X 0 X
X 0 X X 0
X 0 X X X
X X 0 0 0
X X 0 0 X
X X 0 X 0
X X 0 X X
X X X 0 0
X X X 0 X
X X X X 0
X X X X X
1. The computer must be in the PROGRAM mode,
and the cycle programming sequence must be
ready for the next step.
A
3
2. Press the Supply key. The display will read “S.”
Now press the number key–1, 2, 3, 4, or 5–that
corresponds to the desired supply valve.
B
C
D
4
If multiple simultaneous supply injections are
desired, follow this procedure:
●
After the Supply key has been pressed, press
any combination of keys 1–5 (up to 5
individual digits per step) before pressing the
Enter key.
E
F
H
I
●
The computer will add those numbers to the
supply step. All desired supplies will be
turned on for the amount of
J
L
M
5
time programmed.
The display will show either a letter or number
code to indicate the supply combination selected.
For example, assume the computer is in the
program mode and the Supply key has been
pressed. The keys 1, 2, and 5 will be pressed one
at a time. After the last key is pressed, the display
will read “SN” as the first two digits of the
display, followed by the step number, which is
then followed by the cycle number being
programmed. Press the Enter key. The display
will read “M---S.” Now assign the desired time
in minutes and seconds for the supply injection to
last.
6
7
N
8
O
P
Q
9
R
S
3. Press the Enter key and go to the next step in the
cycle.
T
U
V
W
X
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
35
Programming
Programming Heat
Wash
Description
1. To program auxiliary heat (either electric or
steam), the computer must be in the PROGRAM
mode, and the cycle programming sequence must
be ready for the next step.
1
12 seconds forward, pause 3seconds,
12 seconds reverse, pause 3 seconds; repeat
2
3 seconds forward, pause 12 seconds,
3 seconds reverse, pause 12 seconds, repeat
NOTE: Models with both electric and steam heat
are equipped with a selector switch which allows
the user to select either option. Because both
options are energized by the WE-6 computer via
the same output, the procedure for programming a
heat step will be the same for either. The switch
directs the output signal only to the selected option.
3
4
5
No agitation
Distribution speed (forward only)
See Programming a Wash 5 Thermal
Cool-down. Agitation is the same as Wash 1.
4. If Wash 1 is chosen, the no-reverse option may be
selected. The no-reverse option must be selected
at this point in the step programming. Press the
No Reverse key while the display reads
“W1nncc.”
2. The machine must be filled with water.
3. Press the Heat key. The display will read
“HTnncc,” with “nn” representing the step
number and “cc” representing the cycle number.
4. Press the Enter key. The display will read either
“080Fnn” or “025Cnn,” depending on whether
Fahrenheit or Centigrade is prompted.
When the no-reverse option is selected, the
display will change, but the machine will follow
the programming command.
5. Enter the final temperature desired. Three digits
must be entered for the temperature. If the
desired temperature is less than 100 degrees, the
first digit should be “0.” The valid temperature
range is 80–200 degrees Fahrenheit and 25–93
degrees Centigrade. The computer will not
accept temperatures outside of this range. If 100
degrees Fahrenheit is selected, the display will
read “100Fcc.”
The no-reverse option will cause the basket to
run forward only at wash speed for the time
programmed. The computer will return to normal
reversing action when this step is complete.
The no-reverse option may be programmed in
wash, supply, heat, and overflow steps. The No
Reverse key must be pressed just prior to
pressing the Enter key when programming a
step.
6. Press the Enter key. The display will read
“H---M.” Now assign the maximum time in
hours and minutes for the water to reach the
desired temperature.
5. Press the Enter key, and the display will read
“M---S.” Now assign the wash step time in
minutes and seconds.
6. Press the Enter key and go to the next step in the
7. Press the Enter key and go to the next step in the
cycle.
cycle.
7. On machines equipped with optional auxiliary
heat (steam or electric), it is possible to program
a wash step with a temperature step. During such
a step, the machine will perform the programmed
wash at the temperature programmed,
Programming a Wash Step
1. The computer must be in the PROGRAM mode,
and the cycle programming sequence must be
ready for the next step.
maintaining that temperature throughout the step.
2. Press the Wash key. The display will read
To program a wash with a specific temperature,
use the following procedure:
“Wnncc.”
3. Now press the number key (from 1 to 5) that
corresponds to the desired wash step listed in the
following table:
a. After step 3 of Programming a Wash Step,
press the Heat key before pressing the Enter
key. The display will read either “080Fcc” or
“025Ccc,” depending on whether Fahrenheit
or Centigrade is prompted.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
36
Programming
b. Now enter the desired temperature for the
machine to maintain during the wash step.
Fahrenheit and 25–93 degrees Centigrade. The
computer will not accept temperatures outside of
this range. (The cool-down rate will be affected
by the temperature of the cold water available.) If
100 degrees Fahrenheit is selected, the display
will read “100Fcc.”
Three digits must be entered for the
temperature. If the desired temperature is less
than 100 degrees, the first digit must be 0. The
valid temperature range is 80–200 degrees
Fahrenheit and
25–93 degrees Centigrade. The computer will
not accept temperatures outside of this range.
If 100 degrees Fahrenheit is selected, the
display will read “100Fcc.”
4. When the desired cool-down temperature is
displayed, press the Enter key. The display will
show “H--M.” Now enter the maximum time in
hours and minutes for the computer to reach the
target cool-down temperature.
c. Now proceed with step 5 above.
Experimentation may be necessary to determine
the exact time required with each installation to
enable the computer to reach the target cool-
down temperature. Use the edit feature to revise
the Wash 5 step during the experimentation
process.
Programming a Wash 5 Thermal
Cool-down
After programming a heat step, it may be desirable to
program a temperature-controlled thermal cool-down
to gradually reduce the temperature of the load and
prevent fiber shock from sudden cool-down.
When the computer performs the Wash 5 step,
the temperature in the sump must be greater than
the target cool-down temperature. Otherwise, the
computer will advance past the Wash 5 step.
The temperature-controlled cool-down provides a
gradual cooling down from a higher temperature to a
lower temperature. The WE-6 monitors the
temperature of the water in the washer and attempts to
maintain an approximate cool-down rate of three
degrees per minute by periodically energizing the cold
water fill valve.
5. When the desired time is displayed, press the
Enter key and proceed with the next step in the
cycle.
Programming No Reversing
All agitation is programmed by first pressing the
Wash key and then pressing either key 1, 2, 3, 4, or 5
for the type of agitation desired during the wash step.
When the programmed time for the step expires, the
computer will advance to the next step regardless of
whether or not the cool-down temperature has been
reached. If the cool-down temperature is reached
before the time expires, the computer will advance to
the next step.
If no reversing is desired (rotation continuous in one
direction), use the following procedure:
a. Press the Wash key.
During the cool-down, the drain will remain closed
and water will exit through the overflow connection.
The cylinder will rotate in a normal reversing mode as
during a Wash 1 step.
b. Then press either key 1 or key 2.
c. Then press the No Reverse key.
d. Then press the Enter key.
Assuming that the computer is in the program mode
and that a heat step has been created and entered, use
the following procedure to program the thermal cool-
down. (Do not program a drain step before the Wash 5
step.)
The display will show either “W1nncc” or “W2nncc,”
depending on the kind of agitation selected. The
display will not indicate that the no-reverse option was
selected, but the machine will obey the instructions.
1. Press the Wash key and then key 5. The display
NOTE: The no-reverse option is normally used
with Wash 1 steps but may be used with other
appropriate functions. The no-reverse option may
be programmed in wash, supply, heat, and overflow
steps. The No Reverse key must be pressed just
prior to pressing the Enter key when programming
a step. See No. 4 under Programming a Wash Step.
will read “W5nncc.”
2. Press the Enter key. The display will read either
“080F” or “025C,” depending on whether
Centigrade or Fahrenheit is prompted.
3. Enter the desired temperature for the load to cool
down to. Three digits must be used for the
temperature. If the desired target temperature is
less than 100 degrees, the first digit must be “0.”
The valid temperature range is 80–200 degrees
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
37
Programming
Programming a Soak Step
Programming a Drain Step
1. The computer must be in the PROGRAM mode,
and the cycle programming sequence must be
ready for the next step. (The previous step should
have been a fill and/or supply step.)
1. The computer must be in the PROGRAM mode,
and the cycle programming sequence must be
ready for the next step.
2. Press the Drain key. The display will read “D-
2. Press the Soak key. The display will read
nncc.”
“SKnncc.”
3. Press key 1 for a regular drain to sewer or a floor
With machines equipped with auxiliary heat
(optional steam or electric), it is possible to
program a soak-with-temperature step. During
such a step, the machine will soak for the time
programmed at the temperature programmed and
will maintain that temperature throughout the
step.
drain. The display will read “D1nncc.”
4. Press the Enter key. The display will read “M---
S.” Now assign the time which will allow the
machine to drain to empty.
This is an alarm time. The machine should drain
in 30 seconds under normal conditions. The
recommended drain time is one minute. Drain
times of more than one minute are not
recommended.
To program a soak with temperature step use the
following procedure:
a. Press the Heat key after pressing the Soak
key. The display will read either “080Fcc” or
“025Ccc,” depending on whether Fahrenheit
or Centigrade is prompted.
5. Press the Enter key and go to the next step in the
cycle.
NOTE: When programming a drain step, it is
important to select Drain 1. Drain 2 is not available
on the UW60 2-speed or 3-speed washer-extractors.
b. Enter the temperature desired for the machine
to maintain during the soak step. Three digits
must be entered for the temperature. If the
desired temperature is less than 100 degrees,
the first digit should be 0. The valid
temperature range is 80–200 degrees
Fahrenheit and 25–93 degrees Centigrade.
The computer will not accept temperatures
outside of this range. If 100 degrees
Fahrenheit is selected, the display will read
“100Fcc.”
Programming a Flush Step
When the Flush key is pressed, the drain will remain
open and the basket will rotate in slow speed forward
only. Water is added only through the door spray
nozzle.
1. The computer must be in the PROGRAM mode,
and the cycle programming sequence must be
ready for the next step.
3. Press the Enter key. The display will read “H---
M.” Now assign the soak step the desired time in
hours and minutes. During the soak step, no
agitation will occur. The WE-6 microcomputer
will maintain the water level during the soak
cycle at whatever previous level was
2. Press a water temperature key, either Cold, Hot,
or Warm. If the Cold key is pressed, for
example, the display will read
“C-nncc,” etc.
3. Press the Flush key. The display will read
“CFnncc,” “HFnncc,” or “WFnncc,” depending
upon the temperature selected.
programmed.
4. Press the Enter key and go to the next step in the
cycle.
4. Press the Enter key. The display will read “M---
S.” Now assign the desired flush time in minutes
and seconds.
5. Press the Enter key and go to the next step in the
cycle.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
38
Programming
4. Press the Enter key, and go to the next step in the
Programming a Spin Step
cycle.
1. The computer must be in the PROGRAM mode,
and the cycle programming sequence must be
ready for the next step.
NOTE: If a coast-down delay (“SDLY”) is desired
after a rinse step, program a medium-speed spin
step for one second after the rinse step. Then
program the desired coast-down time.
2. Press the Medium Speed or High Speed key.
The display will read “MSnncc” for medium
speed or “HS” for high speed spin.
Programming an Auxiliary Step
NOTE: The WE-6 microcomputer inserts an
automatic 30-second medium-speed spin before
going to high speed for the programmed time.
Auxiliary No. 1 and Auxiliary No. 2 may be used to
control an external buzzer or other device (not
supplied with the machine) with a maximum current
draw of less than 1/2 amp.
3. Press the Enter key. The display will read
“M---S.” Now assign time in minutes and
seconds to the spin step.
Auxiliary No. 3 is identified on the fuse board as SG
(Signal) and controls the built-in buzzer (alarm)
mounted on the inside wall of the control module.
4. Press the Enter key. The display will read
“SDLY” for one second. The display will then
change to “0M-00S.”
When A3 is programmed, the signal will sound
continuously for the duration of time assigned. The
same signal (buzzer) is used by the computer for an
alarm condition, such as a “FILL” or “EMTY” alarm.
5. Now assign the time for the spin delay (coast
down). A minimum of 30 seconds is
recommended to reduce belt wear.
When the signal is activated by the computer to
indicate an alarm condition, the tone will be pulsating
rather than continuous.
A spin delay is always advisable after a high
speed spin.
1. The computer must be in the PROGRAM mode,
and the cycle programming sequence must be
ready for the next step.
Also, always program a spin delay after a high
speed spin if another (non-spin) step is to follow.
NOTE: Do not program a Wash 1 step for a
shakeout after the spin step. If such a step is
programmed, the computer will revert to the
previous wash step and will fill with water
accordingly. See Stop Routine. However, a Wash 1,
2, or 3 step programmed for ONE second will select
stop routine agitation, and avoid refilling.
2. Press the Auxiliary key. The display will read
“A-nncc.” Now press the number key–1, 2, 3, 4,
or 5–that corresponds to the desired auxiliary
function:
A1–Auxiliary No. 1
A2–Auxiliary No. 2
A3–Signal (SG)
A4–Fill to level, using E1 on computer
output board. (E1 is a special function
ONLY. Contact factory for details.)
A5–Provides agitation, no refill.
Programming a Rinse Step
When the Rinse key is pressed on the keypad, the
drain will remain open and the basket will rotate in
medium spin speed. Water is added through the door
spray nozzle only. To program a rinse step, use the
following procedure:
The display will read “A2nncc,” for example, if
key 2 is pressed.
3. Press the Enter key. The display will read
“M---S.” Now assign the auxiliary step the
desired time in minutes and seconds.
1. The computer must be in the PROGRAM mode,
and the cycle programming sequence must be
ready for the next step.
4. Press the Enter key and go to the next step in the
2. Press a water temperature key (Cold, Hot, or
Warm). If the Cold key is pressed, for example,
the display will read “C-nncc,” etc. Then press
the Rinse key. The display will read “CRnncc,”
“HRnncc,” or “WRnncc,” depending on whether
cold, hot, or warm temperature was selected.
cycle.
3. Press the Enter key. The display will read
“M---S.” Now assign the time in minutes and
seconds desired for the duration of the rinse step.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
39
Programming
The simulator is battery powered and is supplied with
an AC transformer which produces 12VDC at 500mA
to recharge the battery pack from a 120V wall plug.
Simulator Operation and Program
Transfer
Simulator Operation
●
The transformer is plugged into the power jack
marked RECHARGE on the front end-panel of
the simulator. The battery pack will be charged
only while the simulator is turned on and is
operating from the transformer.
The WE-6 simulator is an optional accessory to the
WE-6 microcomputer-controlled UWP washer-
energized, the simulator display will show the program
(ROM) identification code for five seconds.
●
●
A fully charged battery pack will give about 3
hours of operation before recharging is necessary.
Allow about 24 hours to fully recharge the
battery pack with the transformer.
NOTE: Cycles for UWP machines are not
compatible with cycles for UWPV machines. DO
NOT transfer cycles from one of these models to
another.
The simulator battery pack contains NiCad
batteries. These batteries will develop a
“memory” according to length of time used. For
example, if the simulator is habitually used for
only one hour before recharging the batteries, the
battery pack will eventually retain this habit and
will power the simulator for only one hour before
charging is required.
●
When replacing the battery, use an exact NiCad
replacement unit. Failure to do so will result in
damage to the simulator.
The WE-6 simulator and the WE-6 microcomputer are
capable of storing and running up to 39 cycles, each
limited to 51 steps.
MC011A
●
The computer will not accept cycle numbers
higher than 39.
Figure 8
All programming instructions in this manual apply to
the simulator as well.
●
If an attempt is made to add a step to a cycle that
already contains 51 steps, the computer will
display “CYFULL” and refuse additional steps.
The simulator is a hand-held unit which serves more
than one purpose:
The front end-panel of the simulator holds the
RECEIVE and TRANSMIT ports for the optic cables
used in program transfers.
●
The simulator’s primary purpose is to
preprogram cycles for transfer to the washer-
extractor and to transfer program cycles between
the washer-extractor and the simulator in either
direction.
●
When transferring cycles from simulator to
computer or computer to simulator, the colored
plugs on the ends of the optic cables must match
the colors of the ports on the simulator and on the
washer-extractor’s control module (gray to gray,
blue to blue).
●
As an instructional aid, the simulator can be used
for teaching programming techniques to
individuals unfamiliar with the UWP WE-6
microcomputer.
●
If a mistake is made connecting the cables, the
display will flash “CONN” and “ERROR” when
the ENTER key is pressed during the last step of
the cycle transfer process.
The keypad and LED display are mounted on the top
of the simulator. The ON/OFF rocker switch is located
on the front end-panel.
The handle pivots to serve as a stand when using the
simulator on a table. To pivot the handles, grasp them
at the point of attachment to the main housing and
gradually pull the handle sides outward until the ends
disengage from the splined mounting holes. Pivot the
handles to the desired position and release.
On the rear end-panel of the simulator are 6 toggle
switches used to simulate various normal operations of
the washer-extractor. These 6 switches simulate or
control the PROGRAM/RUN modes, LOW LEVEL,
MEDIUM LEVEL, HIGH LEVEL, DOOR OPEN/
DOOR CLOSED, and BALANCE.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
40
Programming
2. Place both the simulator and the computer in the
PROGRAM mode. The display on both will read
“CYC00.”
3. Press the 0 key. The display will read “WRITE?”
4. Press the 0 key again. The display will change to
“READ?”
MC012A
5. Press the ENTER key. The display will read
Figure 9
“ALL.”
All the switches must be in the down position to
simulate a machine at rest.
6. Press the ENTER key again. The simulator
display will flash “RECV” and “ALL”
alternately. The computer display will flash
“SEND” and “ALL” alternately.
●
If the PROGRAM/RUN switch is in the up
position, the simulator is placed in the
PROGRAM mode.
When the two displays stop flashing, the transfer
is complete.
●
If the LOW LEVEL switch is in the up position,
a low level water fill is simulated and the
appropriate LED on the display is illuminated.
The MEDIUM LEVEL and HIGH LEVEL
switches operate similarly.
Transferring One Cycle from Computer to
Simulator
All keypad commands will be entered with the
simulator keypad.
●
When a cycle programmed in the simulator is
running, the LEVEL switches must be activated
at the appropriate times in the cycle to indicate to
the computer that the levels have been reached
and that the machine is empty.
Use the following procedure to transfer one cycle
contained in the memory of the computer to the
simulator. (Transferring 1 cycle takes less than 1
second.)
●
●
If the DOOR OPEN/DOOR CLOSED switch is
flipped to the up position (DOOR OPEN) while a
cycle is running, the “DOOR” alarm will be
displayed.
1. Connect the fiber optic cables between the
simulator and the computer. Verify that the
colored plugs on the ends of the optic cables
match the colors of the ports on the simulator and
on the washer-extractor’s control module (gray to
gray, blue to blue).
If the BALANCE switch is in the up position
during the spin step of a cycle, an out-of-balance
condition is indicated to the computer. (See
Balance Detection in the Operation section of
this manual in regard to the drain step.)
2. Place both the simulator and the computer in the
PROGRAM mode. The display on both will read
“CYC00.”
The temperature probe (located on the rear panel of the
simulator) simulates sump temperature.
3. Press the 0 key. The display will read “WRITE?”
4. Press the 0 key again. The display will change to
Transferring All Cycles from Computer to
Simulator
“READ?”
5. Press the ENTER key. The display will read
All keypad commands will be entered with the
simulator keypad.
“ALL.”
6. Press the 0 key. The display will read “CYC.”
Use the following procedure to transfer all cycles
contained in the memory of the computer to the
simulator. (Transferring 39 cycles takes about 6
seconds.)
7. Press the ENTER key. The display will read
“RCYC00.”
Now press the 2-digit code for the desired cycle
number from the computer.
1. Connect the fiber optic cables between the
simulator and the computer. Verify that the
colored plugs on the ends of the optic cables
match the colors of the ports on the simulator and
on the washer-extractor’s control module (gray to
gray, blue to blue).
8. Press the ENTER key. The display will read
“WCYCcc.”
Now press the 2-digit code for the desired cycle
number under which the cycle should be saved in
the simulator.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
41
Programming
9. Press the ENTER key. The simulator display
will flash “RECV” and “CYC” alternately. The
computer display will flash “SEND” and “CYC”
alternately.
2. Place both the simulator and the computer in the
PROGRAM mode. The display on both will read
“CYC00.”
3. Press the 0 key. The display will read “WRITE?”
When the two displays stop flashing, the transfer
is complete.
4. Press the ENTER key. The display will read
“ALL.”
Transferring All Cycles from Simulator to
Computer
5. Press the 0 key. The display will read “CYC00.”
6. Press the ENTER key. The display will read
All keypad commands will be entered with the
simulator keypad.
“RCYC00.”
7. Now press the 2-digit code for the desired cycle
number from the simulator.
Use the following procedure to transfer all cycles
contained in the memory of the simulator to the
computer. (Transferring 39 cycles takes about 6
seconds.)
8. Press the ENTER key. The display will read
“WCYCcc.”
9. Now press the 2-digit code for the desired cycle
number under which the cycle should be saved in
the computer.
1. Connect the fiber optic cables between the
simulator and the computer. Verify that the
colored plugs on the ends of the optic cables
match the colors of the ports on the simulator and
on the washer-extractor’s control module (gray to
gray, blue to blue).
10. Press the ENTER key. The simulator display
will flash “SEND” and “CYC” alternately. The
computer display will flash “RECV” and “CYC”
alternately.
2. Place both the simulator and the computer in the
PROGRAM mode. The display on both will read
“CYC00.”
When the two displays stop flashing, the transfer
is complete.
3. Press the 0 key. The display will read “WRITE?”
4. Press the ENTER key. The display will read
“ALL.”
5. Press the ENTER key again. The simulator
display will flash “SEND” and “ALL”
alternately. The computer display will flash
“RECV” and “ALL” alternately.
When the two displays stop flashing, the transfer
is complete.
Transferring One Cycle from Simulator to
Computer
All keypad commands will be entered with the
simulator keypad.
Use the following procedure to transfer one cycle
contained in the memory of the simulator to the
computer. (Transferring 1 cycle takes less than 1
second.)
1. Connect the fiber optic cables between the
simulator and the computer. Verify that the
colored plugs on the ends of the optic cables
match the colors of the ports on the simulator and
on the washer-extractor’s control module (gray to
gray, blue to blue).
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
42
Programming
Restaurants
Preprogrammed Cycles
21 Table napery, bleach, starch, iron
22 Table napery, bleach, no iron
23 Table napery, colors, starch, iron
24 Table napery, colors, no iron
25 Visa table napery, bleach, starch, iron
26 Visa table napery, bleach, no iron
27 Visa table napery, colors, starch, iron
28 Visa table napery, colors, no iron
This section lists the 39 preprogrammed (ready-to-use)
cycles. To run a wash cycle, first make certain that the
computer is in the RUN mode. Then enter the two-
digit code for the desired cycle, and press the Start
key.
Test Cycle 01 is the first of the 39 preprogrammed
cycles. This cycle is used to verify proper operation of
the machine.
Shirt Laundries
Any of these 39 cycles may be erased and replaced by
new cycles. As shown earlier in this section of the
manual, the cycles may also be edited and revised to
match a particular application’s specific needs. Except
for Cycle 39, all of the preprogrammed cycles use high
speed spin for the final extract.
29 Shirts, colors, no bleach, starch
30 Shirts, bleach, starch
31 Shirts, colored, no bleach, no starch
32 Shirts, no bleach, no starch, delicates
33 Starch, extract only
Formulas Common to All Markets
The following prompts are set at the factory:
34 Uniforms, with bleach
35 Uniforms, without bleach
36 Rags/housekeeping, heavy soil
37 Rags/kitchen, mops
38 Rewash/reclaim
39 Chemical Supply Setup
●
●
●
●
●
Degrees F
One drain
Advance enabled
Manual mode enabled
Dry supplies
Cycle Categories
01 Test
Hotels and Motels
02 Sheets, light soil, cotton/poly blends
03 Sheets, light soil, no bleach, cotton/poly blends
04 Towels, light soil, cotton
05 Towels, light soil, no bleach, cotton
06 Sheets, medium soil, cotton/poly blends
07 Towels, medium soil, cotton
08 Blankets, spreads, no bleach
09 Blankets, spreads, cold water
10 Towels, heavy soil, cotton
11 Rinse and Spin Only
Healthcare
12 Sheets, light soil, cotton/poly blends
13 Towels, light soil, cotton
14 Sheets, heavy soil, cotton/poly blends
15 Towels, heavy soil, cotton
16 Thermal blankets, bleach, cotton
17 Diapers, pads, heavy soil, cotton
18 Personals, bleach
19 Personals, no bleach
20 Pads, polyester
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
43
Programming
For Models built before February 4, 2003
Standard Supply Legend
Supplies are shown by number in the cycle charts. The
following table correlates the supply number with the
supply as it is represented in the cycle charts:
Cycle 01 (Test)
Step
Description
Cold Fill to Low Level
Drain 1
Min:sec
0:30
0:10
5:00
1:00
5:00
0:10
0:10
0:10
0:10
0:10
0:10
0:30
0:30
0:15
0:30
1:00
0:30
0:05
0:05
0:05
5:00
1:00
2:00
1:00
0:15
0:30
1:00
1
2
3
4
5
6
7
8
9
Standard Supply Legend
Supply
Supply Description
Number
Hot Fill to Low Level
Heat, 150°F (66°C)
Cold Fill to High Level
Supply 1
1
2
3
4
5
Detergent
Bleach
Sour
Softener
Specialty
Supply 2
Supply 3
Supply 4
Standard Cycle Charts
10 Supply 5
For Models built after February 4, 2003
11 Supply 1 and 3 (Display: “SB”)
12 Wash 2
Cycle 01
Formulas Common to All Markets
(Chemical Supply Setup)
13 Wash 3
Step
Description
Warm Fill to Low Level
Supply 1
Min:sec
5:00
14 Wash 4
1
2
3
4
5
6
7
8
15 Wash 1, No Reverse
16 Drain 1
2:00
Supply 2
2:00
17 Warm Flush
Supply 3
2:00
18 Auxiliary 1
Supply 4
2:00
19 Auxiliary 2
Supply 5
2:00
20 Auxiliary 3
Wash 1
0:30
21 150°F (66°C) Fill to High Level
22 Cold Fill to Overflow
23 Soak
Drain 1
1:00
NOTE: The cycle shown is intended for setup of
supplies with a 5 supply system. If the machine is
equipped with 8 supplies, refer to Programming a
Supply Step – Models with 8 Supplies. As extra
supplies are normally controlled by bank 2,
program supplies 6, 7, 8, and 9.
24 Drain 1
25 Medium Spin
26 Warm Spray Rinse
27 High Spin (SDLY 0:15)
NOTE: The alarm will sound on steps 01 and 02 (of
Test Cycle). These steps have been deliberately
programmed with times that are too short. Press
Start to continue when alarm sounds. The times
here are actual operating times if the steps are
allowed to progress to their end without pressing
Advance.
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
44
Programming
Cycle 02
Cycle 03
Hotels and Motels
Hotels and Motels
(Sheets, light soil, cotton/poly blends)
(Sheets, light soil, no bleach, cotton/poly
blends)
Step
Description
Hot Fill to Low Level
Supply 1 and 2 (Display: “SA”)
Wash 1
Min:sec
Step
1
Description
Min:sec
1
2
3
4
5
6
7
8
9
5:00
0:45
7:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
2:00
Hot Fill to Low Level
5:00
Supply 1
0:45
7:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
2:00
2
Wash 1
3
Drain 1
Drain 1
4
Hot Fill to High Level
Wash 1
Hot Fill to High Level
Wash 1
5
6
Drain 1
Drain 1
7
Medium Spin
Medium Spin
Warm Spray Rinse
100°F (38°C) Fill to Low Level
Supply 3 and 4 (Display: “SI”)
Wash 1
8
Warm Spray Rinse
9
10 100°F (38°C) Fill to Low Level
11 Supply 3 and 4 (Display: “SI”)
12 Wash 1
10
11
12
13
14
13 Drain 1
Drain 1
14 High Spin (SDLY 0:45)
High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
45
Programming
Cycle 04
Cycle 05
Hotels and Motels
Hotels And Motels
(Towels, light soil, cotton)
Description
(Towels, light soil, no bleach, cotton)
Step
Min:sec
5:00
0:45
7:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
Step
Description
Hot Fill to Low Level
Supply 1
Min:sec
1
2
3
4
5
6
7
8
9
Hot Fill to Low Level
Supply 1 and 2 (Display: “SA”)
Wash 1
1
2
3
4
5
6
7
8
9
5:00
0:45
7:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
Wash 1
Drain 1
Drain 1
Hot Fill to High Level
Wash 1
Hot Fill to High Level
Wash 1
Drain 1
Drain 1
Medium Spin
Medium Spin
Warm Spray Rinse
Warm Spray Rinse
10 110°F (43°C) Fill to Low Level
11 Supply 3 and 4 (Display: “SI”)
12 Wash 1
10 110°F (43°C) Fill to Low Level
11 Supply 3 and 4 (Display: “SI”)
12 Wash 1
13 Drain 1
13 Drain 1
14 High Spin (SDLY 0:45)
14 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
46
Programming
Cycle 06
Cycle 07
Hotels and Motels
Hotels and Motels
(Sheets, medium soil, cotton/poly blends)
(Towels, medium soil, cotton)
Step
Description
Hot Fill to Low Level
Supply 1
Min:sec
5:00
0:45
6:00
1:00
5:00
0:45
6:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
2:00
Step
1
Description
Min:sec
Hot Fill to Low Level
5:00
1
2
3
4
5
6
7
8
9
Supply 1
0:45
6:00
1:00
5:00
0:45
6:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
2
Wash 1
Wash 1
3
Drain 1
Drain 1
4
Hot Fill to Low Level
Supply 2
Hot Fill to Low Level
Supply 2
5
6
Wash 1
Wash 1
7
Drain 1
Drain 1
8
Hot Fill to High Level
Wash 1
Hot Fill to High Level
9
10 Wash 1
10
11
12
13
14
15
16
17
18
Drain 1
11 Drain 1
Medium Spin
Warm Spray Rinse
110°F (43°C) Fill to Low Level
Supply 3 and 4 (Display: “SI”)
Wash 1
12 Medium Spin
13 Warm Spray Rinse
14 100°F (38°C) Fill to Low Level
15 Supply 3 and 4 (Display: “SI”)
16 Wash 1
Drain 1
17 Drain 1
High Spin (SDLY 0:45)
18 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
47
Programming
Cycle 08
Cycle 09
Hotels and Motels
Hotels and Motels
(Blankets, spreads, no bleach)
(Blankets, spreads, cold water)
Step
Description
Warm Fill to High Level
Supply 1
Min:sec
Step
Description
Cold Fill to High Level
Supply 1
Min:sec
1
2
3
4
5
6
7
8
9
5:00
0:45
6:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
1
2
3
4
5
6
7
8
9
5:00
0:45
6:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
Wash 1
Wash 1
Drain 1
Drain 1
Warm Fill to High Level
Wash 1
Cold Fill to High Level
Wash 1
Drain 1
Drain 1
Medium Spin
Warm Spray Rinse
Medium Spin
Cold Spray Rinse
10 Warm Fill to Low Level
11 Supply 3 and 4 (Display: “SI”)
12 Wash 1
10 Cold Fill to High Level
11 Supply 3 and 4 (Display: “SI”)
12 Wash 1
13 Drain 1
13 Drain 1
14 High Spin (SDLY 0:45)
14 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
48
Programming
Cycle 10
Cycle 11
Hotels and Motels
(Rinse and spin only)
Hotels and Motels
(Towels, heavy soil, cotton)
Step
Description
Hot Fill to Low Level
Supply 1
Min:sec
5:00
1:00
7:00
5:00
1:00
7:00
1:00
0:30
3:00
5:00
2:00
1:00
0:30
5:00
1:00
4:00
1:00
5:00
Step
Description
Min:sec
5:00
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
Warm Fill to Low Level
Wash 1
1:00
Wash 1
Drain 1
1:00
Hot Fill to High Level
Supply 2
Medium Spin
Warm Spray Rinse
High Spin (SDLY 0:45)
0:30
1:00
Wash 1
4:00
Drain 1
Medium Spin
Warm Spray Rinse
10 Warm Fill to High Level
11 Wash 1
12 Drain 1
13 Medium Spin
14 Warm Fill to Low Level
15 Supply 3 and 4 (Display: “SI”)
16 Wash 1
17 Drain 1
18 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
49
Programming
Cycle 12
Cycle 13
Healthcare
(Towels, light soil, cotton)
Healthcare
(Sheets, light soil, cotton/poly blends)
Step
Description
Warm Fill to High Level
Wash 1
Min:sec
Step
Description
Warm Fill to High Level
Wash 1
Min:sec
5:00
2:00
1:00
5:00
0:45
8:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
1
2
3
4
5
6
7
8
9
5:00
2:00
1:00
5:00
0:45
8:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
2:00
1
2
3
4
5
6
7
8
9
Drain 1
Drain 1
Hot Fill to Low Level
Supply 1 and 2 (Display: “SA”)
Wash 1
Hot Fill to Low Level
Supply 1 and 2 (Display: “SA”)
Wash 1
Drain 1
Drain 1
Hot Fill to High Level
Wash 1
Hot Fill to High Level
Wash 1
10 Drain 1
10 Drain 1
11 Medium Spin
11 Medium Spin
12 Warm Spray Rinse
13 100°F (38°C) Fill to Low Level
14 Supply 3 and 4 (Display: “SI”)
15 Wash 1
12 Warm Spray Rinse
13 110°F (43°C) Fill to Low Level
14 Supply 3 and 4 (Display: “SI”)
15 Wash 1
16 Drain 1
16 Drain 1
17 High Spin (SDLY 0:45)
17 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
50
Programming
Cycle 14
Healthcare
(Sheets, heavy soil, cotton/poly blends)
Cycle 15
Healthcare
(Towels, heavy soil, cotton)
Step
Description
80°F (27°C) Fill to High Level
Wash 1
Min:sec
Step
Description
80°F (27°C) Fill to High Level
Wash 1
Min:sec
5:00
2:00
1:00
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
1
2
3
4
5
6
7
8
9
5:00
2:00
1:00
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
2:00
1
2
3
4
5
6
7
8
9
Drain 1
Drain 1
120°F (48°C) Fill to High Level
Wash 1
120°F (48°C) Fill to High Level
Wash 1
Drain 1
Drain 1
Hot Fill to Low Level
Supply 1
Hot Fill to Low Level
Supply 1
Wash 1
Wash 1
10 Drain 1
10 Drain 1
11 Hot Fill to Low Level
12 Supply 2
11 Hot Fill to Low Level
12 Supply 2
13 Wash 1
13 Wash 1
14 Drain 1
14 Drain 1
15 Hot Fill to High Level
16 Wash 1
15 Hot Fill to High Level
16 Wash 1
17 Drain 1
17 Drain 1
18 Medium Spin
19 Warm Spray Rinse
20 100°F (38°C) Fill to Low Level
21 Supply 3 and 4 (Display: “SI”)
22 Wash 1
18 Medium Spin
19 Warm Spray Rinse
20 110°F (43°C) Fill to Low Level
21 Supply 3 and 4 (Display: “SI”)
22 Wash 1
23 Drain 1
23 Drain 1
24 High Spin (SDLY 0:45)
24 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
51
Programming
Cycle 16
Cycle 17
Healthcare
(Diapers, pads, heavy soil, cotton)
Healthcare
(Thermal blankets, bleach, cotton)
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
Step
Description
Min:sec
1
2
3
4
5
6
7
8
9
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
1
2
3
4
5
6
7
8
9
80°F (27°C) Fill to High Level
Wash 1
5:00
2:00
1:00
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:30
7:00
1:00
5:00
0:30
7:00
1:00
5:00
4:00
1:00
1:00
2:00
5:00
2:00
1:00
5:00
0:30
4:00
Drain 1
Drain 1
Hot Fill to High Level
Wash 1
Hot Fill to Low Level
Supply 1 and 2 (Display: “SA”)
Wash 1
Drain 1
Hot Fill to Low Level
Supply 1
Drain 1
Wash 1
Hot Fill to High Level
Wash 1
10 Drain 1
11 Hot Fill to Low Level
12 Supply 1
10 Drain 1
11 Medium Spin
13 Wash 1
12 Warm Spray Rinse
13 110°F (43°C) Fill to Low Level
14 Supply 3 and 4 (Display: “SI”)
15 Wash 1
14 Drain 1
15 Hot Fill to Low Level
16 Supply 2
17 Wash 1
18 Drain 1
16 Drain 1
19 Hot Fill to High Level
20 Wash 1
17 High Spin (SDLY 0:45)
21 Drain 1
22 Medium Spin
23 Warm Spray Rinse
24 110°F (43°C) Fill to High Level
25 Wash 1
26 Drain 1
27 110°F (43°C) Fill to Low Level
28 Supply 3 and 4 (Display: “SI”)
29 Wash 1
30 Drain 1
1:00
1:00
4:00
31 Medium Spin
32 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
52
Programming
Cycle 18
Healthcare
(Personals, bleach)
Cycle 19
Healthcare
(Personals, no bleach)
Step
Description
Min:sec
5:00
0:45
6:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
3:00
Step
Description
Min:sec
5:00
0:45
6:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
3:00
1
2
3
4
5
6
7
8
9
Hot Fill to Low Level
1
2
3
4
5
6
7
8
9
Hot Fill to Low Level
Supply 1 and 2 (Display: “SA”)
Wash 1
Supply 1
Wash 1
Drain 1
Drain 1
Hot Fill to High Level
Wash 1
110°F (43°C) Fill to High Level
Wash 1
Drain 1
Drain 1
Medium Spin
Warm Spray Rinse
Medium Spin
Warm Spray Rinse
10 110°F (43°C) Fill to Low Level
11 Supply 3 and 4 (Display: “SI”)
12 Wash 1
10 110°F (43°C) Fill to Low Level
11 Supply 3 and 4 (Display: “SI”)
12 Wash 1
13 Drain 1
13 Drain 1
14 High Spin (SDLY 0:45)
14 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
53
Programming
Cycle 20
Healthcare
(Pads, polyester)
Cycle 21
Restaurants
(Table napery, bleach, starch, iron)
Step
Description
Min:sec
5:00
0:45
3:00
5:00
2:00
1:00
2:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
0:30
5:00
2:00
1:00
0:30
2:00
5:00
0:30
3:00
1:00
4:00
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
1
2
3
4
5
6
7
8
9
110°F (43°C) Fill to Low Level
Supply 1
1
2
3
4
5
6
7
8
9
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
2:00
0:30
5:00
1:00
4:00
Wash 1
Drain 1
130°F (54°C) Fill to High Level
Wash 1
Hot Fill to Low Level
Supply 1
Drain 1
Wash 1
Warm Flush
Drain 1
Hot Fill to Low Level
Supply 1
Hot Fill to Low Level
Supply 2
10 Wash 1
10 Wash 1
11 Drain 1
11 Drain 1
12 Hot Fill to Low Level
13 Supply 2
12 Hot Fill to High Level
13 Wash 1
14 Wash 1
14 Drain 1
15 Drain 1
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to Low Level
18 Supply 3
16 Medium Spin
17 110°F (43°C) Fill to High Level
18 Wash 1
19 Drain 1
19 Wash 1
20 Medium Spin
21 Warm Spray Rinse
22 110°F (43°C) Fill to Low Level
23 Supply 3
20 Supply 5
21 Wash 1
22 Drain 1
23 High Spin (SDLY 0:45)
24 Wash 1
25 Drain 1
26 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
54
Programming
Cycle 22
Restaurants
(Table napery, bleach, no iron)
Cycle 23
Restaurants
(Table napery, colors, starch, iron)
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
1
2
3
4
5
6
7
8
9
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
1
2
3
4
5
6
7
8
9
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
2:00
0:30
5:00
1:00
4:00
Drain 1
Drain 1
Hot Fill to Low Level
Supply 1
Hot Fill to Low Level
Supply 1
Wash 1
Wash 1
Drain 1
Drain 1
Hot Fill to Low Level
Supply 2
Hot Fill to Low Level
Supply 1
10 Wash 1
10 Wash 1
11 Drain 1
11 Drain 1
12 Hot Fill to High Level
13 Wash 1
12 Hot Fill to High Level
13 Wash 1
14 Drain 1
14 Drain 1
15 Medium Spin
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to Low Level
18 Supply 3
16 Warm Spray Rinse
17 110°F (43°C) Fill to Low Level
18 Supply 3 and 4 (Display: “SI”)
19 Wash 1
19 Wash 1
20 Drain 1
20 Supply 5
21 High Spin (SDLY 0:45)
21 Wash 1
22 Drain 1
23 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
55
Programming
Cycle 24
Cycle 25
Restaurants
(Visa table napery, bleach, starch, iron)
Restaurants
(Table napery, colors, no iron)
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
1
2
3
4
5
6
7
8
9
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
1
2
3
4
5
6
7
8
9
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
2:00
1:00
5:00
0:30
2:00
0:30
5:00
1:00
1:00
Drain 1
Drain 1
Hot Fill to Low Level
Supply 1
Hot Fill to Low Level
Supply 1
Wash 1
Wash 1
Drain 1
Drain 1
Hot Fill to Low Level
Supply 1
Hot Fill to Low Level
Supply 2
10 Wash 1
10 Wash 1
11 Drain 1
11 Drain 1
12 Hot Fill to High Level
13 Wash 1
12 Hot Fill to High Level
13 Wash 1
14 Drain 1
14 Drain 1
15 Medium Spin
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to High Level
18 Wash 1
16 Warm Spray Rinse
17 110°F (43°C) Fill to Low Level
18 Supply 3 and 4 (Display: “SI”)
19 Wash 1
19 Drain 1
20 Drain 1
20 110°F (43°C) Fill to Low Level
21 Supply 3
21 High Spin (SDLY 0:45)
22 Wash 1
23 Supply 5
24 Wash 1
25 Drain 1
26 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
56
Programming
Cycle 26
Restaurants
Cycle 27
Restaurants
(Visa table napery, bleach, no iron)
(Visa table napery, colors,
starch, iron)
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
2:00
1:00
5:00
0:30
2:00
0:30
4:00
1:00
1:00
1
2
3
4
5
6
7
8
9
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
2:00
1:00
5:00
0:30
4:00
1:00
1:00
1
2
3
4
5
6
7
8
9
Drain 1
Drain 1
Hot Fill to Low Level
Supply 1
Hot Fill to Low Level
Supply 1
Wash 1
Wash 1
Drain 1
Drain 1
Hot Fill to Low Level
Supply 2
Hot Fill to Low Level
Supply 1
10 Wash 1
10 Wash 1
11 Drain 1
11 Drain 1
12 Hot Fill to High Level
13 Wash 1
12 Hot Fill to High Level
13 Wash 1
14 Drain 1
14 Drain 1
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to High Level
18 Wash 1
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to High Level
18 Wash 1
19 Drain 1
19 Drain 1
20 110°F (43°C) Fill to Low Level
21 Supply 3
20 110°F (43°C) Fill to Low Level
21 Supply 3
22 Wash 1
22 Wash 1
23 Drain 1
23 Supply 5
24 High Spin (SDLY 0:45)
24 Wash 1
25 Drain 1
26 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
57
Programming
Cycle 28
Cycle 29
Restaurants
Shirt Laundries
(Visa table napery, colors, no iron)
(Shirts, colors, no bleach, starch)
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
Step
Description
Hot Fill to Low Level
Supply 1
Min:sec
1
2
3
4
5
6
7
8
9
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
2:00
1:00
5:00
0:30
4:00
1:00
1:00
1
2
3
4
5
6
7
8
9
5:00
0:45
7:00
1:00
5:00
0:45
5:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
0:30
4:00
1:00
4:00
Drain 1
Wash 1
Hot Fill to Low Level
Supply 1
Drain 1
Hot Fill to Low Level
Supply 1
Wash 1
Drain 1
Wash 1
Hot Fill to Low Level
Supply 1
Drain 1
Hot Fill to High Level
10 Wash 1
10 Wash 1
11 Drain 1
11 Drain 1
12 Hot Fill to High Level
13 Wash 1
12 Medium Spin
13 Warm Spray Rinse
14 Cold Fill to High Level
15 Supply 3
14 Drain 1
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to High Level
18 Wash 1
16 Supply 5
17 Wash 1
18 Drain 1
19 Drain 1
19 High Spin (SDLY 0:45)
20 110°F (43°C) Fill to Low Level
21 Supply 3
22 Wash 1
23 Drain 1
24 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
58
Programming
Cycle 30
Cycle 31
Shirt Laundries
Shirt Laundries
(Shirts, bleach, starch)
(Shirts, colored, no bleach, no starch)
Step
Description
Min:sec
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
0:30
4:00
1:00
4:00
Step
Description
Hot Fill to Low Level
Supply 1
Min:sec
5:00
0:45
7:00
1:00
5:00
0:45
5:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
0:30
0:30
4:00
1:00
4:00
1
2
3
4
5
6
7
8
9
Hot Fill to Low Level
1
2
3
4
5
6
7
8
9
Supply 1
Wash 1
Wash 1
Drain 1
Drain 1
Hot Fill to Low Level
Supply 2
Hot Fill to Low Level
Supply 1
Wash 1
Wash 1
Drain 1
Drain 1
Hot Fill to High Level
Hot Fill to High Level
10 Wash 1
10 Wash 1
11 Drain 1
11 Drain 1
12 Medium Spin
13 Warm Spray Rinse
14 Cold Fill to High Level
15 Supply 3
12 Medium Spin
13 Warm Spray Rinse
14 Cold Fill to High Level
15 Supply 3
16 Supply 5
16 Supply 4
17 Wash 1
17 Wash 1
18 Drain 1
18 Drain 1
19 High Spin (SDLY 0:45)
19 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
59
Programming
CYCLE 32
Cycle 33
Shirt Laundries
(Starch, extract only)
Shirt Laundries
(Shirts, no bleach, no starch, delicates)
Step
Description
Min:sec
Step
Description
Min:sec
5:00
Warm Fill to Low Level
5:00
2:00
1:00
5:00
0:45
5:00
1:00
5:00
2:00
1:00
5:00
2:00
1:00
5:00
0:30
0:30
3:00
1:00
1:30
1
2
1
2
3
4
5
6
Warm Fill to Low Level
Wash 1
Supply 3
0:30
Drain 1
3
Supply 5
0:30
Warm Fill to Low Level
Supply 1
4
Wash 1
7:00
5
Drain 1
1:00
Wash 1
6
High Spin (SDLY 0:45)
4:00
Drain 1
7
Warm Fill to High Level
Wash 1
8
9
Drain 1
10
11
12
13
14
15
16
17
18
19
Warm Fill to High Level
Wash 1
Drain 1
Cold Fill to High Level
Supply 3
Supply 4
Wash 1
Drain 1
High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
60
Programming
Cycle 34
Formula Common to All Markets
(Uniforms, with bleach)
Cycle 35
Formula Common to All Markets
(Uniforms, without bleach)
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
Step
Description
Hot Fill to Low Level
Supply 1
Min:sec
1
2
3
4
5
6
7
8
9
5:00
3:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
3:00
1:00
0:30
2:00
5:00
2:00
1:00
5:00
0:30
4:00
1:00
4:00
1
2
3
4
5
6
7
8
9
5:00
0:45
6:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:45
4:00
1:00
3:00
Drain 1
Wash 1
Hot Fill to Low Level
Supply 1
Drain 1
110°F (43°C) Fill to High Level
Wash 1
Wash 1
Drain 1
Drain 1
Hot Fill to Low Level
Supply 2
Medium Spin
Warm Spray Rinse
10 Wash 1
10 110°F (43°C) Fill to Low Level
11 Supply 3 and 4 (Display: “SI”)
12 Wash 1
11 Drain 1
12 Hot Fill to High Level
13 Wash 1
13 Drain 1
14 Drain 1
14 High Spin (SDLY 0:45)
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to High Level
18 Wash 1
19 Drain 1
20 110°F (43°C) Fill to Low Level
21 Supply 3 and 4 (Display: “SI”)
22 Wash 1
23 Drain 1
24 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
61
Programming
Cycle 36
Formula Common to All Markets
(Rags/housekeeping, heavy soil)
Cycle 37
Formula Common to All Markets
(Rags/kitchen, mops)
Step
Description
110°F (43°C) Fill to High Level
Wash 1
Min:sec
Step Description
Min:sec
1
2
3
4
5
6
7
8
9
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
1
2
3
4
5
6
7
8
9
110°F (43°C) Fill to High Level
Wash 1
5:00
2:00
1:00
5:00
0:45
7:00
1:00
5:00
0:45
7:00
1:00
5:00
2:00
1:00
0:30
2:00
5:00
0:30
4:00
1:00
4:00
Drain 1
Drain 1
Hot Fill to Low Level
Supply 1
Hot Fill to Low Level
Supply 1
Wash 1
Wash 1
Drain 1
Drain 1
Hot Fill to Low Level
Supply 2
Hot Fill to Low Level
Supply 2
10 Wash 1
10 Wash 1
11 Drain 1
11 Drain 1
12 Hot Fill to High Level
13 Wash 1
12 Hot Fill to High Level
13 Wash 1
14 Drain 1
14 Drain 1
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to Low Level
18 Supply 3
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to Low Level
18 Supply 3
19 Wash 1
19 Wash 1
20 Drain 1
20 Drain 1
21 High Spin (SDLY 0:45)
21 High Spin (SDLY 0:45)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
62
Programming
For Models built after February 4, 2003
Cycle 38
Formula Common to All Markets
(Rewash/reclaim)
Cycle 39 (Test)
Description
Step
Min:sec
0:30
0:10
5:00
1:00
5:00
0:10
0:10
0:10
0:10
0:10
0:10
1:00
0:30
0:15
0:30
1:00
0:30
0:05
0:05
0:05
5:00
1:00
2:00
1:00
0:15
0:30
1:00
Step
Description
130°F (54°C) Fill to High Level
Wash 1
Min:sec
1
2
3
4
5
6
7
8
9
Cold Fill to Low Level
1
2
3
4
5
6
7
8
9
5:00
2:00
1:00
5:00
0:45
4:00
1:00
5:00
0:45
7:00
1:00
5:00
4:00
1:00
0:30
2:00
5:00
2:00
1:00
5:00
0:30
4:00
1:00
4:00
Drain 1
Hot Fill to Low Level
Heat, 150°F (66°C)
Cold Fill to High Level
Supply 1
Drain 1
Hot Fill to Low Level
Supply 1 and 2 (Display: “SA”)
Wash 1
Supply 2
Drain 1
Supply 3
Hot Fill to Low Level
Supply 1 and 2 (Display: “SA”)
Supply 4
10 Supply 5
10 Wash 1
11 Supply 1 and 3 (Display: “SB”)
12 Wash 2
11 Drain 1
12 Hot Fill to High Level
13 Wash 1
13 Wash 3
14 Wash 4
14 Drain 1
15 Wash 1, No Reverse
16 Drain 1
15 Medium Spin
16 Warm Spray Rinse
17 110°F (43°C) Fill to High Level
18 Wash 1
17 Warm Flush
18 Auxiliary 1
19 Auxiliary 2
19 Drain 1
20 Auxiliary 3
20 110°F (43°C) Fill to Low Level
21 Supply 3 and 4 (Display: “SI”)
22 Wash 1
21 150°F (66°C) Fill to High Level
22 Cold Fill to Overflow
23 Soak
23 Drain 1
24 Drain 1
24 High Spin (SDLY 0:45)
25 Medium Spin
26 Warm Spray Rinse
27 High Spin (SDLY 0:15)
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
63
Programming
For Models built before February 4, 2003
Cycle 39
Formula Common to All Markets
(Chemical Supply Setup)
Step
Description
Warm Fill to Low Level
Supply 1
Min:sec
5:00
1
2
3
4
5
6
7
8
2:00
Supply 2
2:00
Supply 3
2:00
Supply 4
2:00
Supply 5
2:00
Wash 1
0:30
Drain 1
1:00
F232090
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
64
|