OPERATING INSTRUCTIONS
INSTRUCCIONES DE MANEJO
MODE D’EMPLOI
CSD-TD310
CSD-TD320
COMPACT DISC STEREO RADIO CASSETTE RECORDER
English : See page 2.
En
E
Español : Ver la página 10.
Français : Voir page 18.
F
8A-CHB-933-01
010405ACK-I-AIS
U
Power supply
the outlet. To avoid defeating the safety feature of
the polarized plug, do not force it into a power outlet.
AC power cord
3
- When disconnecting the AC power cord, pull it out
by the AC power plug. Do not pull the cord itself.
- Never handle the AC power plug with wet hands,
as this could result in fire or shock.
OPE/BATT
- Power cords should be firmly secured to avoid
being bent, pinched, or walked upon. Pay
particular attention to the cord from the unit to the
power socket.
The OPE/BATT indicator lights up while the power is
on.
- Avoid overloading AC outlets and extension cords
beyond their capacity, as this could result in fire or
shock.
Extension cord - To help prevent electric shock, do
not use a polarized AC power plug with an extension
cord, receptacle, or other outlet unless the polarized
plug can be completely inserted to prevent exposure
of the blades of the plug.
Using on AC house current
Connect the AC cord as illustrated below.
4
5
When not in use - Unplug the AC power cord from
the AC outlet or remove all the batteries if the unit
will not be used for several months or more. When
the cord is plugged in, a small amount of current
continues to flow to the unit, even when the power is
turned off.
to the AC inlet of the unit
supplied AC cord
to an AC outlet
(AC 120 V, 60 Hz)
CAUTION
Use only the supplied AC cord. Use with other cords
may result in the risk of fire.
Maintenance
Clean the unit only as recommended in the Operating
Instructions.
En
Damage Requiring Service
Have the units serviced by a qualified service
technician if:
- The AC power cord or plug has been damaged
- Foreign objects or liquid have got inside the unit
- The unit has been exposed to rain or water
- The unit does not seem to operate normally
- The unit exhibits a marked change in performance
- The unit has been dropped, or the cabinet has been
damaged
Using on batteries
Open the lid of the battery compartment on the rear and
insert eight R14 (size C) batteries, not supplied, with
the 0 and 9 marks correctly aligned. Then close the
lid.
To switch from AC power supply to battery power
supply, disconnect the AC cord from the AC inlet.
DO NOT ATTEMPT TO SERVICE THE UNIT
YOURSELF.
R14 (C)
When to replace the batteries
The OPE/BATT indicator becomes dim, the tape speed
slows down, volume decreases, or sound is distorted
during operation.
Notes on batteries
• Do not mix different types of batteries or old batteries
with new ones.
• When the unit is not to be used for a long period,
remove the batteries to prevent needless battery
wear.
• Never recharge the batteries, apply heat to them or
take them apart.
• Remove dead batteries.
If liquid leaks from the batteries, wipe thoroughly to
remove.
ENGLISH 3
A
RADIO/BAND,
POWER
PLAY/PAUSE/
SKIP/SEARCH
PRESET
6STANDBY
+
TUNE
-
STOP/MEMORY
\
SLEEP
REPEAT
FM MODE
/OSC
TUNER OPERATION
A
1 Press RADIO/BAND repeatedly to select
FM MODE/OSC
- If an FM stereo broadcast contains noise, press the
button so that is displayed.
the desired band.
FM
AM
Noise is reduced, although reception is monaural.
To restore stereo reception, press the button again.
- If a high-pitched sound is heard during AM recording,
press the button repeatedly until the noise is reduced.
Its position can be checked by “•” being on or off the
display.
The power is turned on and the previously tuned
station is received.
2 Press r, t (TUNE -, +) to select a
station.
During FM stereo reception,
is displayed.
To change the AM tuning interval
After listening, press POWER 6STANDBY to turn
the power off.
The default setting of the AM tuning interval is 10 kHz/
step. If you use this unit in an area where the frequency
allocation system is 9 kHz/step, change the interval as
follows.
For better reception
1
2
Press RADIO/BAND to display FM.
Press s while pressing RADIO/BAND to display the
AM frequency.
FM
AM
When the AM tuning interval is changed, the preset
stations are cleared.
NOTE
If the unit picks up noise from other electrical
appliances nearby, like a TV or fluorescent lights, move
the unit away.
Extend the rod antenna
and orient it for the best
reception.
The antenna is inside the
unit. Position the unit for
the best reception.
For quick tuning (Auto Search)
Keep r, t pressed until the tuner starts
searching for a station. When a station is tuned to, the
search stops.
If the broadcast signal is weak, it does not stop. To
stop the search manually, press r or t.
To listen with the headphones
Connect headphones with a stereo mini plug to the \
jack.
4 ENGLISH
Maintenance
To clean the cabinet
Use a soft cloth lightly moistened with mild
detergent solution. Do not use strong solvents
such as alcohol, benzine or thinner.
To clean the heads
When the tape heads are dirty;
- high frequency sound is not emitted
- the sound is not adequately high
- the sound is off-balance
- the tape cannot be erased
- the tape cannot be recorded on
After every 10 hours of use, clean the tape heads
with a head cleaning cassette.
Use separately sold dry-type or wet-type cleaning
cassette.
PRESETTING STATIONS
You can preset up to 15 stations in each band.
1 Select a station.
Refer to the instructions of the cleaning cassette
for details.
Lens
To clean the lens
Use a cotton swab slightly
moistened with cleaning
fluid. Wipe gently from the
center to the edge.
2 Press s STOP/MEMORY once so that “M”
is displayed to store the station.
A station is assigned a preset number, beginning
from 1 in consecutive order for each band.
Preset number
En
Frequency
3 Repeat steps 1 and 2.
The next station will not be stored if a total of 15
preset stations have already been stored for a
band.
To listen to preset stations
Select a band then press e PLAY/PAUSE/PRESET
repeatedly.
To clear a preset station
Select the preset number first. Within 4 seconds, keep
s pressed until “M” and the preset number disappear
in the display.
The higher numbers in the band are decreased by one.
ENGLISH 5
B
CD,
POWER
PLAY/PAUSE/
SKIP/SEARCH
PRESET
6STANDBY
+
TUNE
-
STOP/MEMORY
SLEEP
REPEAT
FM MODE
/OSC
CD OPERATION
B
To start play when the power is off, press CD. The
power is turned on and play of the loaded disc begins
(Direct Play Function).
1 Press CD.
The power is turned on.
2 Press CD OPEN to open the disc
compartment. Place a disc with the
printed side up and close the disc
compartment.
After listening, press POWER 6STANDBY to turn the
power off.
NOTE
CD OPEN
• Do not use irregular shape CDs (example: heart-
shaped, octagonal ones).
It may result in malfunctions.
• Do not place more than one disc in the disc
compartment.
• Do not try to open the disc compartment during play.
• Do not touch the lens. Doing so may cause
malfunctions.
• The unit may not play a CD-R/RW disc that is
recorded on personal computers or some kinds of
CD-R/RW recorders because of differences in
recording platforms.
• Do not attach any seal or label to either side (the
recordable side or the labeled side) of a CD-R/RW
disc. It may cause malfunction.
• Do not load an unrecorded CD-R/RW disc. It will take
over 30 seconds to read the disc. The disc may be
damaged if you try to open the disc compartment
while reading the disc.
Total number of tracks and total playing time are
displayed. It will take about 15 seconds when
loading a CD-RW disc.
3 Press e PLAY/PAUSE/PRESET to
start play.
The number of the track being played and elapsed
playing time are displayed.
s STOP/MEMORY – Stops play.
e PLAY/PAUSE/PRESET – Pauses play. To
resume play, press again.
r,t SKIP/SEARCH – Searches for a particular
point during playback. Keep r or t pressed
and then release it.
– Skips to the beginning of a track. Press r or
t repeatedly.
REPEAT – Repeats a single track or all tracks. Select
as follows.
[
1 : A single track is played repeatedly. Select a
track with r or t.
: All tracks are played repeatedly.
[
6 ENGLISH
Specifications
Tuner section
Frequency range, antenna — FM: 87.5 - 108.0 MHz
Rod antenna, AM: 530/531 - 1,710/1,602 kHz (10/9 kHz
step) Ferrite bar antenna
Deck section
Track format — 4 tracks, 2 channels / Frequency range
— Normal tape: 50 - 12,500 Hz (EIAJ) / Recording
system — AC bias / Erasing system — Magnet erase /
Heads — Recording/playback head (1), Erasure head
(1)
CD player section
Disc — Compact disc / Scanning method — Non-
contact optical scanner (semiconductor laser)
General
Speaker — 80 mm cone type (2) / Output —
Headphones jack (stereo mini-jack) / Power output —
2.5 W + 2.5 W (EIAJ 7 ohms, T.H.D. 10% DC) / Power
requirements — DC 12 V using eight size C (R14)
batteries, AC 120 V, 60 Hz / Power consumption —
18 W / Dimensions (W × H × D) — 310 × 171 × 260 mm
PROGRAMMED PLAY
Up to 30 tracks can be programmed from the disc.
1 In stop mode, keep s STOP/MEMORY
pressed until “M” flashes in the display.
1
3
1
(12 / × 6 / × 10 / in.) / Weight (excluding batteries)
4
4
4
— 2.8 kg (6 lbs. 3 oz.) / Accessory — AC cord (1)
2 Press r, t to select a track, then
press s STOP/MEMORY to store it.
Specifications and external appearance are subject to
change without notice.
Track number
COPYRIGHT
En
Please check the copyright laws relating to
recordings from disc, radio or external tape for the
country in which the machine is being used.
Programmed number
3 Repeat step 2 to program other tracks.
4 Keep s STOP/MEMORY pressed until
“M” stops flashing to finish the program.
“M” remains displayed and indicates the unit stores
the programmed tracks.
5 Press e to start play.
To check the program, press r or t in stop
mode.
To clear the program, press s once in stop mode so
that “M” disappears in the display.
To change the programmed tracks, clear the
program and repeat all the steps again.
If an erroneous display or malfunction occurs
Make sure that none of the deck operation buttons is
pressed.
Press s while pressing POWER 6STANDBY.
If the unit cannot be reset in the way above, disconnect
the AC cord and remove all the batteries to turn off the
display.
Leave the unit for a while and turn the power back on.
ENGLISH 7
QSOUND
VOLUME
3-MODE EQUALIZER
POWER6STANDBY
r, t
C
PAUSE STOP/EJECT FF
REW PLAY
REC
TAPE OPERATION
C
Use Type I (normal) tapes only.
RECORDING
Note that recording is done on only one side of the
tape.
INSERTING A TAPE
Press Z STOP/EJECT to open the cassette
holder and insert a tape with the exposed side
up and the side to be played facing out.
1 Insert a tape with the side to be recorded
facing out.
2 Get ready to record from the source.
To record from a CD, press CD and load the disc.
To record from a radio broadcast, press RADIO/
BAND and tune to a station.
3 Press w REC to start recording.
x PLAY is pressed simultaneously.
When the selected function is CD, CD play and
recording starts simultaneously.
Push the cassette holder to close.
To record only the selected tracks of a CD
Follow steps 1 to 4 of PROGRAMMED PLAY on
page 7 to program tracks.
1
PLAYING A TAPE
2
Press w REC.
Press x PLAY while the power is off.
The power is turned on and play of the inserted tape
begins.
To stop recording, press Z STOP/EJECT. To stop
CD play, press s STOP/MEMORY.
To pause recording, press a PAUSE. To resume
recording, press again.
To erase recording, press w REC while the power is
off.
The volume level is displayed during tape operation.
Z STOP/EJECT – Stops play. The power will be
automatically turned off.
a PAUSE – Pauses play. To resume play, press
again.
f FF/ g REW – Fast forwards/ rewinds. To stop
the winding, press Z.
After recording, press POWER 6STANDBY to turn the
power off.
To prevent accidental erasure
Break off the plastic tabs on the cassette tape with a
screwdriver or other pointed tool after recording.
To record on the tape again
Cover the tab openings with adhesive tape, etc.
Side A
Tab for side A
8 ENGLISH
GENERAL
SOUND ADJUSTMENT
SETTING THE SLEEP TIMER
Volume or tone adjustment does not affect recording.
The unit can be turned off automatically at a specified
time.
VOLUME
1 Keep
the display.
pressed until “30” flashes in
Press VOLUME N or M. The volume level is
displayed as a number from 0 to MAX (25).
• The volume level is automatically set to 14 if the
power is turned off when the volume level is set to
15 or more. (except when turning the power back
on within 4 seconds)
En
3-MODE EQUALIZER
Press 3-MODE EQUALIZER repeatedly until the
desired mode is displayed.
The equalizer mode changes to R (Rock), P (Pop),
J (Jazz) or no equalization, cyclically.
Rock - Emphasizes the high and low range of music.
Pop - Emphasizes voice and midrange of music.
Jazz - Emphasizes the low range of music.
2 Within 4 seconds, press r or t to
specify the time until the power is turned
off.
Each time it is pressed, the time changes between
10 and 90 minutes in 10-minute steps.
QSOUND system
This system provides a rich, three dimensional sound
area for stereo sources.
Specified time
While the sleep timer works,
the dot keeps flashing.
You can enjoy more enhanced sound.
Press QSOUND and the QSOUND indicator lights up.
• At higher volumes, turning QSOUND on may cause
sound distortion. In this case, make the volume
down.
To check the time remaining until the power is
turned off
Repeat step 1 shown above. The remaining time is
displayed for 4 seconds.
To cancel the sleep timer
Display the remaining time and press r or t
repeatedly until OFF is displayed.
NOTE
If the unit is turned off during tape playback, x on the
deck will not be released. Press Z to release x.
ENGLISH 9
NOTE
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
... Reorient or relocate the receiving antenna.
... Increase the separation between the equipment and
receiver.
... Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
... Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
Modifications or adjustments to this product, which are
not expressly approved by the manufacturer, may void
the user’s right or authority to operate this product.
Printed in Indonesia
|