1206
Vandal Resistant Color Pan Tilt Video Door Station
- INSTALLATION INSTRUCTIONS -
FLUSH MOUNTING INSTRUCTIONS
1. Cut a hole in the wall that is 9-1/16" x 6-1/8". (Ensure
that mounting depth of at least 2-11/16" is available.)
2. Pass cable through knockout holes.
3. Secure back box to wall so that front of box is flush with
the outside edge of the wall.
4. Connect wires to the JA-DGV. (See wiring diagram)
5. Attach the JA-DGV to the mounting box using the
supplied screws and tamper proof tool.
JA-DGV
SURFACE MOUNTING INSTRUCTIONS (REQUIRES SBX-DGV, SOLD SEPARATELY)
1. The SBX-DGV is designed to mount to a 1 or 2 gang
box or ring or to any flat surface.
2. Pass cable through knockout holes.
3. Secure mounting box to wall.
4. Connect wires to the JA-DGV. (See wiring diagram)
5. Attach the JA-DGV to the mounting box using the
supplied screws and tamper proof tool.
SBX-DGV
JA-DGV
SAMPLE WIRING DIAGRAM
JA-2MCD
JA-2MECD
Mic
1A1
1A2
A1
A2
Speaker
Call
2A1
2A2
B1
B2
+
A1
A2
Button
JA-DGV
JA-DAC
PS-2420UL
+
-
-
Pg. 1
SPECIFICATIONS
Power Source:
Consumption:
Picture element:
Supplied by master station.
370mA (max.) 4.5mA (Standby, approximate)
CCD camera
Image view area
(approx.):
Vertical Horizontal
In horizontal position:
When pan-and-tilted:
18"
3'
26"
6'
Min. illumination:
Ambient temperature:
Wiring:
Less than 1 Lux (at 20" from camera).
14° F ~ 140° F.
2 parallel wires, non-polarized to master. PE Insulated, low capacitance.
Use Aiphone wire # 871802
Wiring distance:
AWG
Distance
22AWG
165'
18AWG
330'
Dimensions: (HxWxD)
Mounting:
10-3/16" x 7-5/16" x 5/8" (outer panel dimensions)
Flush mount: 9-1/16" x 6-1/8" x 2-11/16" (ABS plastic back box is included)
Surface mount with SBX-DGV: 10-3/8" x 7-7/16" x 3-¼” (top), 2-½” (bottom)
Weight (approx.):
1.90lbs
FCC Class B Verification
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device , pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try and correct the interference by one or more of the following measures:
— Reorient or locate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Note:
Only information pertaining to the connection and operation of the JA-DGV and devices interfacing with it are
included here. For complete installation, wiring, and operational information about the JA system, please refer
to the Installation Manual included with the monitor.
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
(425) 455-0510
FAX (425) 455-0071
TOLL FREE TECHNICAL SUPPORT:
Pg. 3
JA-DGV instr.
1206JD
(800) 692-0200
E-MAIL: [email protected]
|