SAFETY AND OPERATING MANUAL
13 amp fuse
approved to BS1362
18
20b
21
19
20c
22
20a
20d
23a
24
25
Connect
Blue to N
(neutral)
Brown L
(live)
Outer sleeve
firmly clamped
Cable grip
Thank you for purchasing a MacAllister product. We are confident that this product will meet and exceed your
expectations of quality and reliability. Please take the time to carefully read this entire instruction manual
before using your new product, and take note of the basic safety precautions contained herein.
I700W
ROTARY COLLECT MOWER
MAC1700RMA
23b
24
MacAllister Power Tools,
1 Hampshire Corporate Park, Chandlers Ford,
Eastleigh, Hants S053 3YX, U.K.
MacAllister Power Tools,
1 Hampshire Corporate Park, Chandlers Ford,
Eastleigh, Hants S053 3YX, U.K.
Caution: Carefully read this entire Instruction Manual before using this product
Technical Helpline 0845 300 2577
Technical Helpline 0845 300 2577
PMS Black U
Code: MAC1700RMA(B&Q)
Date: 051228 Edition: 9
PMS Warm Red U
Op: DTR
Contents
I -
Parts list
A/1
1
II - Technical data
III - Safety instructions
IV - Getting started
2
5
V - Operation
6
VI - Maintenance and repair
VII - Guarantee
7
9
VIII - EC Declaration of conformity
10
I - Parts list
II - Technical data
1. Upper handle
2. Power button
Voltage:.....................................230–240V ~ 50 Hz
Motor power:...............................................1700W
No-load speed:.....................................4500min-1
Cutting width (swathe):........................36cm (14”)
Cutting heights:
3. Power on indicator
4. Motor on/off grip (x 2)
5. Power cable
6. Motor cable
With blue spacer in place...................................
5 (16mm, 25mm, 35mm, 45mm and 60mm)
With blue spacer removed.................................
5 (22mm, 31mm, 41mm, 51mm and 66mm)
Grass box capacity:..................................34 litres
Approximate weight:.....................................16 kg
7. Handle joint (x 2)
8. Handle twist lock (x 2)
9. Wing knob (x 2)
10. Power cable tidy
11. Blade spanner
12. Motor cable saddle clip (x 2)
13. Hinged cover
14. Cover latch
15. Mower body
16. Height adjustment lever
17. Lower handle
18. Lower handle fixing clip (x 2)
19. Grass box
NOISE AND VIBRATION DATA
A weighted sound pressure level:..........83 dB(A)
A weighted sound power level:...........95.8 dB(A)
Declared guaranteed sound power level:
.............................................................96 dB(A)
Typical weighted vibration:.....................4.76m/s2
20. Wheel (x 4)
21. Front handle
22. Blade
23. Blade bolt
The sound intensity level for the operator
may exceed 85dB(A) and sound protection
measures are necessary
24. Blade height spacer (blue)
25. Blade height spacer (yellow)
26. Filter cover
27. Filter
1
III - Safety instructions
GENERAL SAFETY INSTRUCTIONS
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair, clothing, and
gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
that these are connected and properly used.
Use of these devices can reduce dust-related
hazards.
ADDITIONAL SAFETY RULES FOR ROTARY
MOWERS
•
•
•
•
Inspect and maintain the mower regularly. Have the
mower repaired only by an authorised repairer.
If power cord is damaged, only have it repaired or
replaced by an authorised service centre.
Check that all grass cuttings and dirt have been
removed from the ventilation vents.
WARNING. Read all instructions. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious personal injury. The term “power
tool” in all of the warnings listed below refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
•
Only use this Lawn Mower when a Residual Current
Device (RCD) with a tripping current of not more than
30mA is in the circuit.
•
If an extension cord is used make sure it is for outdoor
use and marked as such. The recommended size
of extension cord is not lighter than 1.5mm2 and a
maximum of 10 metres in length.
When not in use, store the mower out of the reach of
children and infirm people.
SAVE THESE INSTRUCTIONS
•
Completely uncoil your extension cable before use
to prevent overheating and loss of mower efficiency.
When tidying away the cable, wind it carefully to avoid
kinking.
WARNING. In order to reduce the risk, disconnect the
plug from the supply power, only use recommended
accessories as required, otherwise personal injury may
result.
1) WORK AREA
a) Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
4) POWER TOOL USE AND CARE
WARNING. After switching off the machine, the cutting
blade continues to rotate for a few more seconds.
•
Do not use the machine to cut grass which is not on
the ground. For example, do not cut grass which is on
rocks.
Do not switch on the machine in enclosed or poorly
ventilated spaces or in the presence of inflammable
and/or explosive substances such as liquids, gasses
and powders.
Always stop the mower and switch off at the mains
when cutting is delayed, emptying the grass box or
when walking from one cutting location to another.
Do not cross roads or gravel paths with the machine
still running.
Do not move the machine by pulling on the electrical
cable. Always use the handgrip.
Keep a balanced and stable stance while using the
machine.
Ensure that the area being cut is free from strings,
stones and debris. Remove any objects that could be
thrown during cutting or could wind around the cutting
mechanism.
If you hit or become entangled with a foreign object,
stop the motor and disconnect from the mains
immediately to check for damage. Repair any damage
before further operation is attempted. Do not operate
the mower with loose or damaged parts.
Do not cut against hard objects. This could cause
injury to the operator and damage to the machine.
Keep your hands, face and feet away from all moving
parts.
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts,
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc., in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use
of the power tool for operations different form
intended could result in a hazardous situation.
•
Frequently inspect the condition of the cutting blades.
Damaged blades must be replaced immediately. Blunt
blades should be sharpened. Follow all the required
precautions when replacing the blades.
Before use check the supply and extension cord
for signs of damage or ageing. If the cord becomes
damaged during use, disconnect the cord from the
supply immediately. DO NOT TOUCH THE CORD
BEFORE DISCONNECTING THE SUPPLY.
Do not use the appliance if the cord is damaged or
worn.
Read the instructions carefully. Be familiar with the
controls and proper use of the equipment.
Keep extension cord away from cutting blades.
Wear eye and ear protection. Wear dust protection
if the mowing action causes the raising of dust or
particles.
•
2) ELECTRICAL SAFETY
•
•
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
•
•
•
•
•
•
•
•
•
Never allow children, infirm people or people
unfamiliar with these instructions to use the rotary
collect mower.
•
•
Avoid using the mower, while people, especially
children and the infirm, or pets are nearby.
Use the mower only in daylight or good artificial light.
Do not operate the mower unless the grass box is in
place.
•
•
•
•
•
•
Never operate the mower with a damaged base.
Never operate the appliance with defective guards
or shields, or without safety devices, for example
deflectors and/or grass catcher, in place.
When starting up and when the machine is in
operation, keep the cutting section away from all parts
of the body, especially the hands and feet.
Do not start the machine when it is not in the operating
position.
•
•
If possible, avoid cutting wet grass.
3) PERSONAL SAFETY
Exercise proper caution when mowing on sloping
ground. Watch your footing and wear non-slip
footwear. Mow along the slope not up and down it. Do
not mow on steep slopes. Be especially cautious when
changing direction on slopes – stand above the mower
to avoid risk of injury.
a) Stay alert, watch what you are doing and
use common sense when operating a power
tool. Do not use a power tool while you are
tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use safety equipment. Always wear eye
protection. Safety equipment such as a dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is
in the off-position before plugging in. Carrying
power tools with your finger on the switch or
plugging in power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the tool on. A wrench or a key that is left
attached to a rotating part of the power tool may
result in personal injury.
•
•
•
5) SERVICE
•
Never operate the mower barefoot or when wearing
open sandals or canvas shoes.
a) Have your power tool serviced by a qualified
repair personnel using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Thoroughly inspect the mower for loose or damaged
parts before each use. Do not use the unit until
adjustments or repairs are made.
•
•
Do not mow by pulling the machine towards you.
When mowing, keep the cable away from the mower.
Your direction of work should be away from the power
point. Mow in straight lines, not in circles.
Always keep hands and feet away from rotating parts.
When the machine is not in use, store it in a dry, and
high or locked-up place, out of reach of children.
Check the grass catcher frequently for wear or
deterioration.
After use, disconnect the machine from the power
supply and check for damage. If you have the slightest
doubts, check with an authorised service centre.
Only use the machine according to the instructions
given in this manual.
•
•
•
Use only the manufacturer’s recommended
replacement parts and accessories.
Always disconnect the mower from the mains when
leaving it unattended.
Switch the motor off and pull out the plug when the
machine is not being used, being cleaned, being
moved from one place to another or when the blades
are being changed or adjusted.
•
•
•
•
•
If there is an interruption to the power supply or the
extension cable is damaged, switch off the machine
immediately and remove the plug from the power
point.
•
2
3
NOTE. There are two spacers under the blade,
one coloured blue (24) and one coloured yellow
(25).
IV - Getting started
1
The blue spacer can be removed to increase the
incremental cutting heights by an extra 6mm
at all 5 settings of the height adjustment lever
(16).The mower must not be operated without
the yellow spacer (25) in position under the
blade. Instructions on how to remove the blue
spacer are given in the section on changing the
mower blade (Section VI).
•
•
•
Check regularly that the nuts, bolts, screws and other
fittings are tight and secure.
Keep the mower free of grass, leaves and other
debris build-up.
Do not tilt the appliance when switching on the motor,
except if the appliance has to be tilted for starting.
In this case, do not tilt it more than is absolutely
necessary and lift only the part which is away form
the operator. Always ensure that both hands are in the
operating position before returning the appliance to
the ground.
UNPACKING
Due to modern mass production techniques, it
is unlikely that your power tool is faulty or that
a part is missing. If you find anything wrong, do
not operate the tool until the parts have been
replaced or the fault has been rectified. Failure
to do so could result in serious personal injury.
CAUTION. Keep the two arms of the upper
handle (1) parallel and insert them into the
handle joints, both at the same time. If you
insert one arm and then the other, you may
damage the joints. When removing the handle,
keep the arms parallel and remove both arms at
the same time.
The mower is supplied partially disassembled.
The parts in the carton are:
•
•
Do not try to repair the machine or access internal
parts. Use authorised service centres only.
Do not get distracted and always concentrate on what
you are doing. Use common sense. Never operate
the machine when you are tired, sick or under the
influence of alcohol or other drugs.
Disconnect the unit from the power supply when not in
use, before servicing and when changing the blades.
Keep these instructions. Refer to them frequently and
use them to instruct other users. If you loan someone
this unit, also loan them these instructions.
The operator or user is responsible for accidents or
hazards occurring to other people or their property.
• Mower body (with blade fitted)
• Upper handle (including switchbox, motor on/
off grips, handle joints with twist locks, motor
cable saddle clip and 15m power cable)
•
•
• Lower handle (including cable tidy, motor
cable saddle clip and blade spanner)
6
Ensure that each arm of the upper handle (1)
is properly seated in the handle joints (7) as
follows:
•
• Grass box
• 2 wing knobs and 2 lower handle fixing clips
Failure to follow operating instructions and safety
precautions in this instruction manual can result in
serious injury. Read the manual before starting or
operating this unit.
• Loosen the two handle twist locks (8).
ASSEMBLY
• Keeping the two arms of the upper handle
parallel, make sure that the upper handle (1) is
fully inserted into the handle joints (7).
CAUTION. Never carry out any assembly
operations or adjustments with the power
connected to the mower. Always ensure that the
power button is in the off position and that the
power plug is disconnected from the supply.
Wear eye protection
Wear hearing protection
Wear respiratory protection
• Retighten the two handle twist locks (8)
turning them clockwise.
NOTE. Make sure that the switchbox is facing
upwards and that the orange-coloured power
cable (5) is not wrapped around the handle.
It must trail freely behind the switchbox on the
upper handle.
2
Symbols
Ensure that the handle is in the correct
orientation i.e. the cable tidy (10) must be on
the uppermost side of the lower handle (17)
as shown on the main photograph. Fit the two
tubes of the lower handle (17) into the slots in
the mower body (15).
The rating plate on your tool may show symbols. These
represent important information about the product or
instructions on its use.
7
Wear hearing protection.
Wear eye protection.
Wear respiratory protection.
Do not run the mower over objects.They can
be thrown and cause severe injury.
ADJUSTING THE CUTTING HEIGHT
3
CAUTION. Never carry out any assembly
operations or adjustments with the power
connected to the mower. Always ensure that
the power button is in the off position and
that the power plug is disconnected from the
supply. Choose a level area with a firm surface,
press the cover latch (14), lift the cover (13) and
remove the grass box (19).
Keep bystanders, especially children and pets
at a distance of greater than 5m.
Double insulated for
additional protection.
Fix the ends of the lower handle in position with
the two lower handle fixing clips (18).
Switch off and remove the plug before
adjusting, cleaning or if the cord is damaged.
Conforms to relevant
safety standards.
4
Using the two saddle clips (12), secure the
black-coloured motor cable (6) to the upper
handle (1) and lower handle (17).
Avoid injury, do not place hands or feet near
the rotating blade.
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
Blade continues to rotate after the mower
is switched off.Wait until all parts are
stationary before touching them.
8
5
Pull the height adjustment lever (16) towards you
then move it to the right to increase the cutting
height or to the left to decrease the cutting
height.
Fit the handle joints (7) of the upper handle (1)
over the die-cast ends of the lower handle (17)
and secure them together with the wing knobs
(9).
Do not use in the rain or leave the mower
outdoors whilst it is raining.
Read the instruction manual.
Warning.
4
5
Release the lever to lock it in one of the five
stop positions.
immediately and have the problem corrected.
• Keep your hands on the upper handle in order
to control the mower.
and disconnect the power cable plug from the
power point.
Do not use a damaged tool and attach a label
“DO NOT USE” to the tool.
Ensure that you are on a flat surface and have
secure footing.
NOTE. There is a blue spacer (24) located
under the blade. It can be removed to increase
the incremental cutting heights
• Allow the motor to stop completely before
releasing control of the handle.
Ensure that you are on a flat surface and have
secure footing.Check that the upper handle (1)
is in line with the lower handle (17) and that the
wing knobs (9) are securely tightened.
Press the cover latch (14) and lift the hinged
cover (13).
14
by an extra 6mm at all 5 settings of the height
adjustment lever (16).
MOWING
Lift out the grass box (19), empty it, replace it
and close the hinged cover (13).
WARNING. Only use this mower when a
Residual Current Device (RCD) with a tripping
current of not more than 30mA is in the circuit.
Instructions on how to remove this spacer are
given in Step 19.
WARNING. Do not operate the mower unless
the grass box is in place.
HEIGHT ADJUSTMENT WITH BLUE
SPACER IN POSITION
VI - Maintenance
and repair
NOTES:
V - Operation
• Cut grass when it is dry.
• Keep the mower blade sharp and balanced.
Lever position
Cutting height
16mm
10
1
2
3
4
5
25mm
35mm
45mm
60mm
• Do not set the cutting height too low,
especially at the beginning of the mowing
season.
17
SWITCHING ON AND OFF
CHANGING THE MOWER BLADE
IMPORTANT. Practise switching on and
switching off the mower as detailed below
before using it to cut grass for the first time.
CAUTION. Never carry out any assembly
operations or adjustments with the power
connected to the mower. Always ensure that the
power button is in the off position and that the
power plug is disconnected from the supply.
• Vary the cutting pattern with each mowing.
• Use the cable restraint to secure the power
cable (5) in order to prevent any pulling forces
on the cable from being transmitted to the
switch box.
Start the mower on a hard, level surface
(such as a driveway) that is free of debris.
HEIGHT ADJUSTMENT WITH BLUE
SPACER REMOVED
Connect the power cable (5) to the power point.
Lever position
Cutting height
22mm
Periodically check the blade (22) for nicks and
dull cutting edges and have it sharpened if
needed.
NOTE. The power on indicator (3) lights
showing that power is connected.
1
2
3
4
5
• Make sure that the work area is free of rocks,
debris, string or cord and other foreign
objects.
31mm
41mm
51mm
66mm
11
NOTE. The blade should be sharpened and
balanced by an authorised repair centre.If there
are rounded or broken ends, thinned metal or
other damage, replace the blade.
• Where possible, start the mower before
approaching the grass to be cut.
Squeeze one of the motor on/off grips (4)
towards the upper handle (1) and use the other
hand to press the power button (2). The power
button remains depressed as long as the
pressure is maintained on the motor on/off grip
(4).
Replace the grass box (19).
• Cut the grass by moving in a straight line and
proceed slowly.
With the power button (2) in the off position and
the power plug removed from the supply, take
out the grass box (19) and turn the mower on
its side.
9
• Start cutting nearest the mains power source
and work away from it to make it easier to
avoid the cable.
BEFORE STARTING
ATTENTION. Due to the power input of this
product on start up, voltage drops may occur
and this can influence other equipment
(e.g. dimming lights). So for technical reasons
we advise, if the mains-impedance is
Zmax<0.444 Ohm, these disturbances are not
expected. If you require further clarification, you
may contact your local power supply authority.
12
• At the edge of the lawn, take care to maintain
the mower parallel with the ground to prevent
“scalping” of the grass.
18
Transfer the other hand to squeeze the second
motor on/off grip (4).
Put on a pair of sturdy gloves to protect your
hands. Block the rotation of the blade (22) and
use the blade spanner (11) to unscrew the blade
bolt (23) in an anti-clockwise direction (viewed
from underneath).
As the motor picks up speed you are ready to
begin mowing.
• Do not cut damp or wet grass.
• Do not overload the mower.
To stop the motor, release pressure on both
motor on/off grips (4) until the power button (2)
clicks off.
After finishing the cutting operation, release
pressure on both motor on/off grips (4)
and allow the motor to come to a complete
standstill.
Before use, check that the mower is in good
working order.
19
The motor is not started if pressure is re-
applied to the motor on/off grips (4) alone. It is
necessary to squeeze a motor on/off grip (4)
and re-press the power button (2) to re-start
the motor.
Remove the blade bolt (23) and blade (22)
taking care not to disturb any blade height
spacers (24 and 25) that might be fitted.
Ensure the power button is in the off position
and disconnect the cable plug from the mains
supply.
15
NOTE. The blue spacer (24) can be removed
to increase the incremental cutting heights
by an extra 6mm at all 5 settings of the height
adjustment lever (16).
Remove the cable plug from the mains supply.
Examine the general condition of the mower.
Inspect the body underneath the cover, blade,
switch, power cord and extension cord (if used).
16
13
EMPTYING THE GRASS BOX
EMERGENCY STOP
Check for loose screws, misalignment, binding
of moving parts, improper mounting, broken
parts and any other condition that may affect
its safe operation. If abnormal noise or vibration
occurs during operation, turn the mower off
The mower must not be operated without the
yellow spacer (25) in position under the blade.
As the grass collection box (19) fills with grass, it
is clearly visible through the translucent material
of the box.
• To stop the motor in an emergency, simply
release the pressure on both motor on/off
grips.
20
Ensure the power button (2) is in the off position
Check that the blade height spacers (24 and 25)
6
7
are properly located, add the replacement blade
(22) and screw in the blade bolt (23), tightening
it with the blade spanner (11).
At the end of the season, give the mower
an overall cleaning and a thorough check,
including the blade. Have the blade sharpened
or replaced if necessary.
VII - Guarantee
Thank you for investing in MacAllister.
Return the blade spanner (11) to its storage
position in the cable tidy (10).
These products have been made to demanding,
high quality standards and are guaranteed for
domestic use against manufacturing faults for a
period of 36 months from the date of purchase.
You can clean out the grass box with a hose or
pressure cleaner provided that you first remove
it from the mower. Replace the grass box when
it is dry.
Press down on the blade spanner (11) to lock it
in position under the retaining latch.
To take advantage of this free extended
warranty please register on the website. This
guarantee does not affect your statutory rights.
If your product fails due to a defect in material or
workmanship during this period, please return it
to your nearest B&Q store.
Return the mower to the upright position and
replace the grass box (19).
Do not let water come into contact with the
motor.
Reconnect the power cable to the supply and
run the mower for a few minutes to check that
the blade is properly fitted and that there is no
undue noise or vibration.
Never use chemicals such as petrol or solvents
to clean plastic parts.
Never disassemble the tool or carry out any
repairs.
Normal wear and tear, including accessory
wear, is not covered under guarantee. The
product is guaranteed for 12 months if used for
normal trade purposes. Any guarantee is invalid
if the product has been overloaded or subject
to neglect, improper use or an attempted
repair other than by an authorised agent.
Heavy duty, daily professional or hire usage
are not guaranteed. Due to continuous product
improvement, we reserve the right to change
the product specification without prior notice.
Use only the blade as recommended by the
manufacturer.
Always have the mower maintained or repaired
by a competent person at an authorised service
centre.
21
CLEANING THE FILTER
25
To help maintain good airflow within the grass
box and thus ensure optimum filling, regularly
check and, if necessary, clean the filter (27).
GENERAL INSPECTION
Regularly check that all fixing screws are tight.
They may vibrate loose over time.
Access the filter by using a flat blade screwdriver
to prise off the filter cover (26).
26
22
PLUG REPLACEMENT
Take out the filter, wash it in warm, soapy water,
rinse it and allow it to dry.
If you need to replace the fitted plug then follow
the instructions below.
IMPORTANT. The wires in the mains lead are
coloured in accordance with the following code:
23
Clean out the filter area and replace the filter
and the filter cover (26).
Blue – Neutral Brown – Live
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows. The blue wire
must be connected to the terminal which is
marked with N or coloured black. The brown
wire must be connected to the terminal which is
marked with an L or coloured red.
NOTE. This filter is a consumable item and not
a warranty item.
24
MAINTENANCE
Store the tool, instruction manual and
accessories in a secure, dry place. You will
then always be able to refer to the relevant
information when required.
WARNING. Never connect live or neutral wires
to the earth terminal of the plug.
In order to take up less space when storing the
mower, loosen both wing knobs (9) and fold the
upper handle (1) over the lower handle (17).
Only fit an approved 13 Amp BS1363/A plug
and the correct rated fuse.
NOTE. If a moulded plug is fitted and has to
be removed take great care in disposing of the
plug and severed cable, it must be destroyed to
prevent engaging into a socket.
When not in use, keep the cord wrapped
around the cable tidy.
Keep the tool’s air vents accessible when the
cover (13) is raised, unclogged and clean at all
times.
Remove dust and dirt regularly.
Clean inside the mower body and under the
deck. Use a brush or damp rag.
8
9
VIII - EC Declaration of conformity
DECLARATION OF CONFORMITY
1 Hampshire Corporate Park
Chandlers Ford, Hampshire, SO53 3YX, U.K.
We declare that the ROTARY COLLECT MOWER MAC1700RMA conforms with the following
EEC Directives their supporting Statutory Instruments and relevant standards, where applicable
as follows:
The Machinery Directive 98/37/EC
The Low Voltage Directive 73/23/EEC amended by 93/68/EEC
The EMC Directive 89/336 amended by 93/68/EEC
The Outdoor Noise Directive 2000/14/EC
EN 60335-1:1994+A1+A2+A11+A16
EN 60335-2-77: 2000
EN 50366: 2003
EN55014-1: 2000+A1 + A12
EN55014-2: 1997+A1
EN61000-3-2: 2000
EN61000-3-11:2000
The noise emission in the environment by equipment for use outdoors (ANNEX VI- Internal
control of production with assessment of technical documentation and periodical checking)
2000/14/EC.
Measured sound power level: 95.8 dB(A)
Guaranteed sound power level: 96 dB(A)
Mr Kevin McGilvray
Director of Quality Assurance
B&Q plc
26th August 2005
10
11
12
|