Abocom Network Card FE1000 User Manual

10/100Mbps Dual Speeds  
Fast Ethernet  
PC Card Ethernet  
Adapter  
Quick Installation Guide  
 
Connecting and Removing the Cable of Media  
Coupler to the PC Card  
Grasp the PC Card 15-pins connector at the end of  
the media coupler with the pointing triangle facing  
upward. Gently insert it into the mating connector  
on the PC Card until it clicks in place at both sides.  
Attention should be paid when removing the  
15-pins connector. Please press the both sides of the  
connectors before dragging out of the PC Card.  
Connecting to the Network  
Connect unshielded twisted pair (UTP) cable to  
the RJ-45 connector of media coupler before  
loading any network driver.  
symbol 108 \f "Monotype Sorts" \s 6O For operation in  
the100Mbps (100Base-TX) Ethernet network, a  
Category 5 unshielded twisted pair(UTP) cable  
-2-  
 
should be used to connect between media coupler  
and 100Mbps hub or switch.  
symbol 108 \f "Monotype Sorts" \s 6O For operation in the 10Mbps  
(10Base-T) Ethernet network, Category 3, 4 or 5  
unshielded twisted pair (UTP) cable could be used  
to connect between the media coupler and a  
10Mbps hub or switch.  
LED Indicators  
-3-  
 
SOFTWARE INSTALLATION  
Plug the driver diskette into the floppy drive and set  
the current drive to the floppy drive. Then run  
INSTALL to install the real mode drivers such as  
ODI or NDIS 2.x or Packet Drivers into the target  
disk.  
Novell Netware  
There are two methods to install the Netware client  
ODI driver, the menu installation and Netware 3.12  
or 4.x Client installation.  
Menu Installation  
1.Run INSTALL.EXE from the root directory of  
driver diskette.  
2.Select Netware 3.x and 4.x Workstationitem  
from menu.  
-4-  
 
3.If current settings are acceptable, select Start  
Installation and go to step 5. Otherwise, select  
Modify Parameters to make settings changed  
4.Move cursor to focus on the setting you want to  
make change and press <Enter>” to select a fit  
value. When the configurations are set  
completely, press <Enter> on the OK” field to  
If you wanted to install the ODI driver by  
manual, you may follow the instructions list  
below.  
1.Copy the files LE100ODI.COM and NET.CFG  
from the path \NETWARE and the file  
LANEN.EXE from the path \ENABLER in the  
driver diskette into the Netware client directory  
containing Novell's LSL.COM, IPXODI.COM  
and NETx.COM files.  
-5-  
 
2.Using a text editor to edit the NET.CFG for  
setting the default frame type. In the Netware  
server the frame type is set to 802.3 for NW3.11  
and 802.2 for NW3.12 and NW4.x The frame  
type must be set to the same with the server or  
the client couldnsymbol 146 \f "Parisian BT" \s  
10’}t login to the server.  
3.Follow Novell's instructions on using ODI  
programs.  
You  
can  
substitute  
the  
LE100ODI.COM whenever a reference is made  
to the Hardware Specific Module.  
4.A typical ODI workstation startup batch file  
includes:  
>LANEN /IRQ=dd /IOP=xxx Card Enabler  
>LSL  
;Link Support Layer Module provided by  
Novell  
>LE100ODI  
>IPXODI  
;Hardware Specific Module  
;IPX Protocol Stack Module provided by  
Novell  
>NETx  
;Shell Support Module provided by Novell  
>LOGIN  
Novell Client Installation  
1.Run the NetWare Client Install V1.21  
-6-  
 
-Get the 4 Client disks from the network  
administrator, or  
-Run the \NWCLIENT\INSTALL.EXE in a  
previous Installation  
2.A message appears on the screen asking you  
whether or not you want the program to perform  
modifications on your AUTOEXEC.BAT and  
CONFIG.SYS files.  
3.Answer "Yes". The program then modifies your  
AUTOEXEC.BAT and CONFIG.SYS files  
accordingly and creates backup copies.  
4.The following message appears:  
-Install support for MS Windows? (Y/N):  
5.Answer accordingly and provide a path if  
necessary.  
6.The program displays the following:  
-Configure your workstation for backup by a  
NetWare server running software such as  
BACKUP? (Y/N):  
7.Answer accordingly and provide a path if  
necessary.  
8.Select a driver for your network board.  
9.From the driver list, select Other Drivers.  
-7-  
 
10.Go to the Insert the Driver Disk dialog box and  
specify the path where the ODI driver and INS  
files reside. For example: C:\ODI.DOS.  
11.Press Enter and select the target ODI driver.  
12.Specify the driver's optional settings.  
13.Press F10 to save to new configuration.  
14.Highlight "Install press here" and press <Enter>  
to install.  
The program copies the necessary files for NetWare  
Client. Continue the installation procedure to  
completion. Upon completion, a new NET.CFG file  
will be created in your DOS directory. Typically,  
this file contains the following lines:  
Link Driver LE100ODI  
#FRAME Ethernet_802.3  
FRAME Ethernet_802.2  
:
15.Copy the file LANEN.EXE from the directory  
\ENABLER in the driver diskette to Netware  
Client directory.  
16.Edit the STARTNET.BAT by a text editor. Add  
an running LANDEN command at the beginning  
of the file. An STARTNET.BAT for the ODI  
workstation performs as the following  
LANEN /IOP=nnn /IRQ=n  
-8-  
 
--Card Enabler  
SET NWLANGUAGE=ENGLISH  
--Set NetWare 4.X to English  
language  
LSL  
--Link Support Layer Module  
provided by Novell  
LE100ODI  
IPXODI  
--Hardware Specific Module  
--IPX Protocol Stack Module  
provided by Novell  
VLM  
--DOS Support Module provided by  
Novell  
F:  
--Change to connected device  
--Login to file server as user xxx  
LOGIN xxx  
17.Run STARTNET to access the Novell network.  
MS LAN Manager  
1.View the README.TXT on the installation  
diskette in the \NDIS2 directory. Before  
installing the drivers, please ensure that the  
Microsoft LAN Manager has been installed in  
the target path. The installation program will  
check and modify the PROTOCOL.INI file for  
LAN Manager.  
2.Run INSTALL.EXE from root directory of  
driver diskette.  
-9-  
 
3.Select Microsoft LAN Manager item on the  
menu screen.  
4.If current settings are acceptable, select Start  
Installation” and go to step 6. Otherwise, select  
Modify Parameters” to make setting changed.  
5.Move cursor to each field you want to make a  
change and press <Enter> to select a fit value.  
When the configuration are set completely, press  
<Enter> on the OK field to exit the screen and  
go back to step 4.  
6.Installation program starts to copy related files  
from driver diskette to the destination directory  
and  
modifies  
CONFIG.SYS  
and  
PROTOCOL.INI under usersymbol 146 \f  
"Parisian BT" \s 10’}s agreement.  
7. Please reboot the computer to load driver and  
start LAN Manager in batch.  
-10-  
 
Example of PROTOCOL.INI: used by LAN  
Manager  
[PROTMAN]  
DRIVERNAME = PROTMAN$  
DYNAMIC = YES  
PRIORITY = NETBEUI  
[NETBEUI_XIF]  
Drivername = netbeui$  
SESSIONS = 6  
NCBS = 12  
BINDINGS = "LE100NDS_NIF"  
LANABASE = 0  
[LE100NDS_NIF]  
; protocol.ini session for LAN driver.  
IOADDRESS = 0x320  
INTERRUPT = 11  
-11-  
 
DRIVERNAME = LE100NDS$  
Packet Driver  
1.Run INSTALL.EXE from root directory of  
driver diskette.  
2.Select Packet Driver item on the menu screen.  
3.If current settings are acceptable, select Start  
Installation and go to step 5. Otherwise, select  
Modify Parameters” to make setting changed.  
4.Move cursor to focus on the field you want to  
make a change and press <Enter> to select a fit  
value. When the configuration are set  
completely, press <Enter> on the OK” field to  
exit the screen and go back to step 3.  
5.Installation program starts to copy related files  
from diskette to the  
destination directory and  
modifies AUTOEXEC.BAT under usersymbol  
146 \f "Parisian BT" \s 10’}s agreement.  
6.Please reboot the computer to load the driver.  
ODI Driver for Workgroups  
1.Run Windows for Workgroups and click  
Network Setup” icon in Network group.  
2.In Network Setup dialog box, click Networks...”  
button to select the network operating system.  
-12-  
 
3.In Networks dialog box, check Install Microsoft  
Windows Network and Others, thereafter select  
Novell NetWare (Workstation Shell, 3.X) or  
Novell NetWare (Workstation 4.0 and above)  
and press OK to enter the screen of  
PXODI.COM and LSL.COM”  
4.Press OK to go back the Network Setup“ screen.  
5.Click on Drivers...” button to select network  
driver.  
6.In Network Drivers dialog box, press Add  
Adapter...” button to enter Add Network  
Adapter dialog box. Select Unlisted or Updated  
Network Adapter and press OK.  
7.Windows will prompt an Install Driver dialog  
box. In this time, put the driver diskette into  
floppy drive and press OK.  
8.Select the Netware ODI Driver ...” string and  
press OK.  
9.Follow Windows instructions to complete the  
installation and exit Windows.  
10.Run INSTALL.EXE from root directory of  
driver diskette.  
11.Select Windows for Workgroups” in Network  
Operating System screen.  
-13-  
 
12.If current settings are acceptable, select Start  
Installation” and go to step 13. Otherwise,  
select Modify Parameters” to make settings  
changed.  
13.Move cursor to focus on the setting you want to  
make a change and press <Enter> to select a fit  
value.  
When the configuration is set  
completely, press <Enter> on the OK field to  
exit the screen and go back to step 11.  
14.Select Novell Netware Server as the network  
server you will attach to and press <Enter> key.  
15.Installation program starts to copy related files to  
the destination directory and modifies  
AUTOEXEC.BAT and NET.CFG under  
usersymbol 146 \f "Parisian BT" \s 10’}s  
agreement.  
16.Please reboot the computer to have the driver  
take effect.  
Windows NT 4.0  
Assumed that the Network Services already  
installed in the NT 4.0 system.  
1.Insert the Fast Ethernet PC Card into any one of  
PC Card Slots in system.  
2.Power up Windows NT 4.0  
-14-  
 
3.Open My Computer  
4.Open Control Panel  
5.Run the Network  
6.Select Adapters page  
7.Press Add to add network adapter  
8.Press Have Disk button  
9.Insert the driver disk into drive A:  
10.Specify the path to ” A:\ and press OK  
11.A dialog box will appear to adjust the  
driver's settings. The resources assignment to  
the adapter must be unique in the system.  
12.Press OK when all settings are completed.  
13.Press Close to complete network setting  
Windows 95 Installation  
1.Assumed that the drivers of PC Card slot are  
well installed. The System Icon in the Control  
Panel can report on its functionality. Apart from  
above mentioned, any questions on this layer  
need to be taken up with the computer's  
manufacturer.  
-15-  
 
2.Insert the PC Card into the slot. In New  
Hardware Found dialog box, select Driver from  
disk provided by hardware manufacturer”.  
3.Please input the path, A:\ and insert driver diskette.  
The driver will be installed and you may be  
asked for the original Windows 95 CD/disks.  
4.For the first time installation, please click  
Network icon in Control Panel to add Protocols,  
Client and Service if you needed  
5.Reboot the machine and the card will be fully  
functional.  
Artisoft Lantastic 6.0 Installation  
1.Install LANTASTIC 6.0 first.  
-16-  
 
2.Run INSTALL.EXE from root directory of  
driver diskette.  
3.Select LANTASTIC 6.0 in Network Operating  
System screen.  
4.If current settings are acceptable, select Start  
Installation” and go to step 6. Otherwise, select  
Modify Parameters” to make settings changed.  
5.Move cursor to focus on each field you want to  
make a change and press <Enter>” to select a fit  
value. When the configuration is set completely,  
press <Enter>” on the OK field to exit the  
screen and go back the step 4.  
6.Installation program starts to copy the related  
files from diskette to the destination directory  
and modifies CONFIG.SYS, PROTOCOL.INI,  
and STARTNET.BAT under usersymbol 146 \f  
"Parisian BT" \s 10’}s agreement.  
7. Please reboot the computer to have the driver  
take effect.  
IBM OS/2 Warp  
NDIS2 Driver for OS2 Warp  
Before the driver installation, please ensure that the  
PCMCIA Service was installed and worked  
-17-  
 
properly. If the PCMCIA Service of OS/2 Warp has  
been enabled already, please jump to portion B for  
driver installation otherwise please follow the  
instructions in the following to install the PCMCIA  
Service.  
A. Enable PCMCIA Service of OS/2 Warp  
1.In the OS/2 Desktop group, double-click on the  
OS/2 System icon.  
2.Double-click on the System Setup icon.  
3.Double-click on the Selective Install icon.  
4.Select the PCMCIA Support button.  
5.Select PCMCIA system.  
For example: select IBM ThinkPad 750  
6.Click OK”.  
7.Click Install  
8.Select the source drive and directory  
For Example D:\OS2IMAGE  
9.Click Install  
10.Click OK  
B. Install NDIS2 driver for IBM LAN Server  
4.0  
-18-  
 
1.In the OS/2 Desktop group, double-click on the  
MPTS icon.  
2.Click on the Configure button.  
3.Select the LAN adapters and protocols option.  
4.Click on the Configure button.  
5.Select the Other adapters ...” option.  
6.Insert the driver diskette and type the driver path:  
A:\OS2\NDIS2  
Click on the OK button.  
7.Select PCMCIA Ethernet Adapter, and then  
click on the Add button.  
8.Select IBM OS/2 NETBIOS, and then click on  
the Add button.  
9.Click OK”.  
10.Click Close”.  
11.Click Exit”.  
12.Shutdown and restart your system.  
-19-  
 

Abocom Headphones BSH202 User Manual
Addonics Technologies Network Card ST5DVRE User Manual
ADTRAN Network Router MX410 User Manual
Agilent Technologies Thermometer FS2343 User Manual
Aiphone Smoke Alarm 4A User Manual
Airlink101 Network Card AWLL5025 User Manual
Alesis Musical Instrument 7 51 0262 A User Manual
Allied Telesis Network Router 86241 02 User Manual
Altec Lansing Portable Speaker iM3 User Manual
Altinex Switch MT110 103 User Manual