ULS Series
Condenser Microphones
Description
Features
The AKG C 480 B preamplifier powering unit is the latest
model in the ULS series. It accommodates the CK 61/ULS,
CK 62/ULS, CK 63/ULS capsules and the new CK 69/ULS
shotgun capsule, providing a higher order of performance for
these capsules than heretofore available. The new preamp
has a vastly improved noise floor, permitting self noise
performance with the four associated capsules in the range
• Ultralow noise preamplifier for use
with ULS series capsules
• Multiple directional capsules and
configurations available on a high
of 9 to 11 dB-A. Maximum sound pressure levels in the range
of 144 dB (in the -10 dB sensitivity position) can be attained
with no greater than 0.5% distortion, giving the capsules a
new level of overall performance. An integral low cut filter
(12 dB/octave) can be set for either 150 or 70 Hz. The +6 dB
sensitivity position is intended to enhance the performance of
the CK 69/ULS interference tube capsules, which normally
operate over large distances. With the available CK 61/ULS
cardioid, CK 63/ULS hypercardioid, CK 62/ULS
performance powering/preamp
module
• Extremely flat on-axis response for
all models
• Three sensitivity settings
(0, +6, and -10 dB)
omnidirectional, and highly directional CK 69/ULS shotgun
element, the C 480 Series is intended primarily for studio,
broadcast and a variety of live sound and speech
• High acoustic level capability
reinforcement applications in which state-of-the-art
performance is mandated. A complete line of optional
accessories is available. The C 480 B operates only on 48
volts phantom powering.
Architects and Engineers Specifications
C 480 B with CK 61/ULS
The microphone shall be of the condenser type with capsule and
powering module assembly no larger than 0.8 in. (21 mm)
in diameter. The microphone shall accept phantom powering at
48 volts. The nominal output impedance shall be equal to or
less than 150 ohms at 1 kHz, and the output shall be
transformerless. The microphone shall provide a three position
control for normal (0 dB), elevated sensitivity (+6 dB), and
attenuated (-10 dB) sensitivity. Switchable low-frequency cuts at
150 Hz and 75 Hz at 12 dB/octave shall be provided.
The polar pattern shall be cardioid and nominal on-axis
frequency response shall be 20 Hz-20 kHz. For the normal
sensitivity setting of 0 dB, microphone sensitivity shall be at
least 20 mV/Pa, and the self noise floor shall be no higher than
11 dB-A. The 0.5% THD operating level shall be no lower than
140 dB SPL.
The microphone shall be the AKG Model C 480 B preamp
operating with the AKG Acoustics Model CK 61/ULS capsule.
C 480 B with CK 62/ULS
The microphone shall be of the condenser type with capsule
and powering module assembly no larger than 0.8 in. (21 mm)
in diameter. The microphone shall accept phantom powering at
48 volts. The nominal output impedance shall be equal to or
less than 150 ohms at 1 kHz, and the output shall be
transformerless. The microphone shall provide a three position
control for normal (0 dB), elevated sensitivity (+6 dB), and
attenuated (-10 dB) sensitivity. Switchable low-frequency cuts at
150 Hz and 75 Hz at 12 dB/octave shall be provided.
The polar pattern shall be omnidirectional and nominal on-axis
frequency response shall be 20 Hz-20 kHz. For the normal
sensitivity setting of 0 dB, microphone sensitivity shall be at
least 20 mV/Pa, and the self noise floor shall be no higher than
11 dB-A. The 0.5% THD operating level shall be no lower than
140 dB SPL.
The microphone shall be the AKG Model C 480 B preamp
operating with the AKG Acoustics Model CK 62/ULS capsule.
C 480 B with CK 63/ULS
The microphone shall be of the condenser type with capsule and
powering module assembly no larger than 0.8 in. (21 mm)
in diameter. The microphone shall accept phantom powering at
48 volts. The nominal output impedance shall be equal to or less
than 150 ohms at 1 kHz, and the output shall be transformerless.
The microphone shall provide a three position control for normal (0
The polar pattern shall be hypercardioid and nominal on-axis
frequency response shall be 20 Hz-20 kHz. For the normal
sensitivity setting of 0 dB, microphone sensitivity shall be at least
20 mV/Pa, and the self noise floor shall be no higher than 11 dB-A.
The 0.5% THD operating level shall be no lower than 140 dB SPL.
The microphone shall be the AKG Model C 480 B preamp
dB), elevated sensitivity (+6 dB), and attenuated (-10 dB) sensitivity. operating with the AKG Acoustics Model CK 63/ULS capsule.
Switchable low-frequency cuts at 150 Hz and 75 Hz at 12
dB/octave shall be provided.
C 480 B with CK 69/ULS
The microphone shall be of the condenser type with
capsule and powering module assembly no larger than
0.8 in. (21 mm) in diameter. The microphone shall accept phantom
powering at 48 volts. The nominal output
impedance shall be equal to or less than 150 ohms at
1 kHz, and the output shall be transformerless. The microphone
shall provide a three position control for
normal (0 dB), elevated sensitivity (+6 dB), and attenuated
(-10 dB) sensitivity. Switchable low-frequency cuts at
150 Hz and 75 Hz at 12 dB/octave shall be provided.
The polar pattern shall be two-section shotgun and nominal
on-axis frequency response shall be 20 Hz-18 kHz. For the
normal sensitivity setting of 0 dB, microphone sensitivity shall
be at least 27 mV/Pa, and the self noise floor shall be no
higher than 9 dB-A. The 0.5% THD operating level shall be no
lower than 140 dB SPL.
The microphone capsule shall consist of two sections. The
total length of the microphone with a single capsule length shall
be no greater than 12.8 in. (326 mm), and for the dual capsule
the length shall be no greater than 18.4 in. (467 mm).
The microphone shall be the AKG Model C 480 B preamp
operating with the AKG Acoustics Model CK 69/ULS capsule.
Specifications
(measured with C 480 B preamp)
Models:
CK 61/ULS:
CK 62/ULS:
CK 63/ULS:
CK 69/ULS:
Transducer Principle:
All models externally polarized condenser capsules.
Frequency Range
Polar Pattern:
20–20,000 Hz 1 dB
20–20,000 Hz 1 dB
20–20,000 Hz 1 dB
20–18,000 Hz 2 dB
Cardioid
Omnidirectional
Hypercardioid
Shotgun (2-section)
Sensitivity at 1,000 Hz:
(0 dB setting):
(+6 dB setting):
20 mV/Pa; -34 dBV
40 mV/Pa; -28 dBV
6.3 mV/Pa; -44 dBV
20 mV/Pa; -34 dBV
40 mV/Pa; -28 dBV
6.3 mV/Pa; -44 dBV
20 mV/Pa; -34 dBV
40 mV/Pa; -28 dBV
6.3 mV/Pa; -44 dBV
27 mV/Pa; -31 dBV
54 mV/Pa; -25 dBV
8.5 mV/Pa; -41 dBV
(-10 dB setting):
Equivalent Noise Level:
(0 dB setting):
(+6 dB setting):
11 dB-A
13 dB-A
17 dB-A
11 dB-A
13 dB-A
17 dB-A
11 dB-A
13 dB-A
17 dB-A
9 dB-A
11 dB-A
15 dB-A
(-10 dB setting):
Max. SPL for 0.5 % THD
(0 dB setting):
(+6 dB setting):
140 dB
134 dB
144 dB
140 dB
134 dB
144 dB
140 dB
134 dB
144 dB
140 dB
134 dB
142 dB
(-10 dB setting):
S/N Ratio (:
(0 dB setting):
(+6 dB setting):
(-10 dB setting):
83 dB
81 dB
77 dB
83 dB
81 dB
77 dB
83 dB
81 dB
77 dB
85 dB
83 dB
79 dB
Model:
C 480 B
Electr. Impedance:
Load Impedance:
Power Requirement:
Connector:
≤ 150 ohms (transformerless)
> 2,000 ohms in parallel with 1,000 pF
48 volts phantom power ( 4 volts)
3 pin XLR type
Size:
dia 0.8 in. (21 mm) length 5.9 in. (150 mm)
Models:
Finish:
C 480 B with CK 61/ULS:
C 480 B with CK 62/ULS:
C 480 B with CK 63/ULS:
C 480 B with CK 69/ULS:
non reflective black
non reflective black
non reflective black
non reflective black
Size of Microphone
Combinations:
dia 0.83 in. (21 mm)
length 6.8 in. (173 mm)
dia 0.83 in. (21 mm)
length 6.8 in. (173 mm)
dia 0.83 in. (21 mm)
length 6.8 in. (173 mm)
dia 0.83 in. (21 mm)
length 12.8 in. (326 mm)
(for single section)
length 18.4 in. (467 mm)
(for dual section)
Models:
CK 61/ULS:
CK 62/ULS:
CK 63/ULS:
CK 69/ULS:
dia 0.83 in. (21 mm)
length 1.0 in. (26.5 mm)
dia 0.83 in. (21 mm)
length dia 1.0 in. (26.5 mm)
dia 0.83 in. (21 mm)
length 1.0 in. (26.5 mm)
dia 0.83 in. (21 mm)
length 6.9 in. (176 mm)
(for single section)
12.5 in. (317 mm)
(for dual section)
Models:
Net/Shipping Weigth:
C 480 B:
3.5 oz. (100 g)
18 oz. (500 g)
CK 61/ULS:
0.9 oz. (25 g)
5.3 oz. (150 g)
CK 62/ULS:
0.9 oz. (25 g)
5.3 oz. (150 g)
CK 63/ULS:
0.9 oz. (25 g)
5.3 oz. (150 g)
CK 69/ULS:
2.5/3.5 oz. (70/100 g)
1.1 lbs. (480 g)
Included Accessories:
Optional Accessories:
SA 40 Stand adapter, W 32 Foam windscreen (for CK 61/ULS, 62/ULS, and 63/ULS),
Foam windscreens for both tube lengths (CK 69/ULS)
H 30 Elastic suspension, N 62 E AC Power supply, Battery power supply, SA 38 H Stand adapter/suspension,
SA 18/2B All-metal stand adapter, A 61 Swivel adapter, VR 61 12 in. (30 cm) Extension tube, W 46 All-metal windscreen,
VR 62 3 ft. (90cm) Extension tube.
or consequential damages. However, the limitation of any right or remedy shall not be effective
Limited Warranty
where such is prohibited or restricted by law. Simply take or ship your AKG product prepaid to our
service department. Be sure to include your sales slip as proof of purchase date. (We will not repair
transit damage under the no-charge terms of this warranty.) Note: No other warranty, written or oral
is authorized by AKG Acoustics, Inc. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. Some states do not allow the exclusion or
limitation of incidental or consequential damages or limitation on how long an implied warranty
lasts, so the above exclusions and limitation may not apply to you.
Valid only in the United States. AKG Acoustics warrants AKG products against defects in material
or workmanship for a period of two years from the date of original purchase for use, and agrees to
repair or, at our option, replace any defective unit without charge for either parts or labor. Important:
This warranty does not cover damage resulting from accident, misuse or abuse, lack of reasonable
care, the affixing of any attachment not provided with the product, loss of parts or connecting the
product to any but the specified receptacles. This warranty is void unless service or repairs are
performed by an authorized service center. No responsibility is assumed for any special, incidental
Microphones · Headphones · Wireless Microphones · Wireless Headphones · Headsets · Electroacoustical Components
AKG Acoustics GmbH
Lemböckgasse 21–25, P.O.B. 158, A-1230
Vienna/AUSTRIA
Tel: (43 1) 86 654-0*, Fax: (43 1) 86 654-516
AKG ACOUSTICS, U.S.
914 Airpark Center Drive
Nashville, TN 37217, U.S.A.
Tel: (615) 620-3800, Fax: (615) 620-3875
Studer Japan Ltd.
AKG Acoustics; A Division of Harman Pro Germany
Bodenseestraße 228, D-81243 München/GERMANY
Tel: (089) 87 16-0, Fax: (089) 87 16-200
2-43-7, Uehara, Shibuya-ku, Tokyo 151-0064/JAPAN
Tel: (813) 3465-2211, Fax: (813) 3465-2214
Erikson Pro Audio
Arbiter Pro Audio
Wilberforce Road, London NW9 6AX/ENGLAND
Tel: (0181) 202 1199, Fax: (0181) 202 7076
620 McCaffrey, St-Laurent, Quebec, H4T 1N1, CANADA
Tel: (514) 738-3000, Fax: (514) 737-5069
Specifications subject to change without notice.
DS-ULS Series
|