T1ESFCSUACE
Stand Alone and Smart 16 T1 Network Facility Interface
The ADTRAN® T1 ESF CSU™ is a full-featured
T1 Channel Service Unit used to connect T1
data terminal equipment (DTE) such as a PBX,
switch or channel bank to T1 facilities. Capable
of interfacing to both B8ZS or AMI circuits, the
T1 ESF CSU can convert signal formats or line
code to integrate older equipment. The ESF
CSU is designed to provide alarms, loopbacks,
signal regeneration, line build-out, and surge
protection, while maintaining 1’s density for
the DTE and T1 network.
built-in local and remote loopback tests and
conducting stress testing of the network with
built-in test patterns. For more extensive
network testing, the unit uses bantam jack
access for external test equipment. To aid with
circuit monitoring, the T1 ESF CSU gathers
AT&T maintenance information in 15 minute
intervals for 24 hours, which is fully accessible
over the FDL or via the Smart 16 controller.
Product Features
I Provides T1 facility
interface and jitter
tolerance per ANSI
T1.403, T1.102 and
AT&T TR 62411
I Supports B8ZS or
AMI formats
I Conversion for signal
formats and line coding
Remote configuration is made simple by
using the FDL channel for the standalone
ACE or the Smart 16 controller interface for
the rackmount version. Using the remote
configuration capability of the T1 ESF CSU
enables central site control and setup for
ADTRAN T1 CSUs or TSU devices.
I Transmits unframed
"All 1’s" during signal loss
from DTE or T1 Network
The T1 ESF CSU ACE is suitable for wall- or
rackmounting or desktop use, while the T1 ESF
CSU Smart 16 Card occupies a single slot in the
rackmount ADTRAN Smart 16 shelf. The stand-
alone models provide a front panel LCD, four
user keys on the front of the ACE, and provides
easy configuration and unit monitoring from
the front panel. The ESF CSU provides an EIA-
232 port (DB-9) for provisioning through a
VT100 interface. The Smart 16 ESF CSU card
can be controlled from the shelf controller
through a VT100 interface or the optional
Datamate™. For SNMP management, the Smart
16 ESF CSU card is supported by the Smart 16e
controller and the ADVISION software package.
I Front Panel LCD and
4 button keypad (ACE)
I Equipment line build-out
configuration 0-655 feet
The standalone ACE includes an auto-
ranging 12-48V internal DC power supply and
wallmount AC power supply. The L2 version
adds a terminal block for easier connection to
an external DC supply.
I Standalone ACE package
or Smart 16 single
slot card
I Supports Performance
Report Messages of ANSI
T1.403 and AT&T 54016
maintenance messages
For additional T1 applications, ADTRAN
provides several T1 DSU/ CSUs and T1
Multiplexers for combining traditional DSX-1
functionality with additional DTE ports. The
TSU 100e™, TSU 120e™ and TSU 600e™ are
modular T1 DSU/ CSUs with embedded SNMP
and are capable of supporting a single DSX-1
interface and up to 22 DTE interfaces for data
or video applications.
IIIIndustry-leading five-year
North American warranty
The T1 ESF CSU provides a T1 network
interface and a DSX-1 DTE connection through
modular RJ48C jacks. For testing purposes, the
T1 ESF CSU is capable of initiating several
PBX, Channel Bank,
DSU, LAN Router, etc.
T1 ESF CSU ACE
T1
T1
D4, AMI
ESF, B8ZS
PSTN
Test Jacks
Test Equipment
Front panel control eliminates
need for ASCII terminal in
local control applicatons.
Remote
Monitoring
and Control
May also be a direct connection
(no modems necessary)
RS-232
Interface
Modem
Modem
|