ADTRAN Network Router 1335 Series User Manual

For more detailed documentation, visit us online at www.adtran.com.  
®
NetVanta 1335 Series  
P/N 1700515E2  
Quick Start Guide  
NETVANTA 1335 FRONT PANEL LAYOUT  
GETTING STARTED  
3. Insert the connector of the provided power cord into the power interface on the rear panel of  
the unit, and plug the cord into a standard electrical outlet.  
Two configuration methods are available for your NetVanta 1335 Series units:  
Web-based GUI  
4. Once the unit is powered up, open a VT100 terminal session using the following settings:  
AOS Command Line Interface (CLI)  
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the AOS CLI.  
The GUI lets you configure the main unit settings and provides online guidance and explanations for  
each setting. However, using the AOS CLI may be necessary for more advanced configurations.  
5. Enter enable at the > prompt. Enter the enable password when prompted. The default  
password is password.  
ACCESS THE GUI  
You may access the web-based GUI from any web browser on your network by following these  
steps:  
The configuration parameters used in the examples outlined in this  
document are for instructional purposes only. Please replace all  
underlined entries (example) with your specific parameters to configure  
your application.  
1. Connect the switch to your PC using any of the 24 Ethernet ports on the front of the unit.  
2. Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address, you  
will need to change the unit’s IP address using the CLI. (Refer to the next two sections for  
instructions.)  
CONFIGURE THE UNITS IP ADDRESS  
3. Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1.  
The following steps create an IP address and subnet mask for the virtual interface vlan 1. If you  
are not sure what IP address to assign, please contact your network administrator.  
4. You will then be prompted for the username and password (the default settings are admin and  
password).  
1. At the # prompt, enter config terminal.  
5. The initial GUI screen appears.  
2. At the (config)# prompt, enter interface vlan 1 to access the configuration parameters for  
the virtual LAN (VLAN) interface.  
ACCESS THE CLI  
3. Enter ip address 10.26.12.12 255.255.255.0 to assign an IP address to the VLAN interface  
Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the  
NetVanta unit’s CONSOLE port, you need the following items:  
using a 24-bit subnet mask.  
4. Enter no shutdown to activate the virtual interface to pass data.  
5. Enter exit to return to the Global Configuration mode.  
VT100 terminal or PC (with VT100 terminal emulation software)  
Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate  
interface for your terminal or PC communication port on the other end  
1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear panel  
of the unit.  
2. Connect the other end of the serial cable to the terminal or PC.  
Quick Start Guide, 61700515E2-13A, November 2006  
Copyright © 2006 ADTRAN, All Rights Reserved  
 

Acer Personal Computer X3950 User Manual
AEG Cooktop 6510K7 M User Manual
Amazon Tablet 23 000466 01 User Manual
American DJ Music Pedal FSR 800 User Manual
Atlas Webcam DD6 User Manual
Atlona Car Amplifier AT HD V112 User Manual
Atlona TV Cables ATP 14029 User Manual
ATMT MP3 Player MP130 User Manual
Audiovox Remote Starter 07S1BP User Manual
Behringer Music Mixer PMP518M User Manual