HeatSeal
H212/H312
with SureFlow™ Technology
G
F
D
I
O
E
P
T
K
c
Instruction Manual
Manuel d’utilisation
Bedienungsanleitung
Manuale d’istruzioni
Gebruiksaanwijzing
Manual de instrucciones
Manual de Instruções
Kullanım Kılavuzu
Οδηγίες
Brugsvejledning
FI
o
Käyttöopas
NO
o
Bruksanvisning
S
Q
o
Bruksanvisning
Instrukcja obsługi
Návod k obsluze
Használati útmutató
CZ
H
RUS
o
Руководствo по
зкcплyатации
1
2
4
6
3
5
7
Safety instructions
Important safeguards
m
m
YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS IMPORTANT
TO ACCO BRANDS EUROPE. IN THIS INSTRUCTION MANUAL AND ON
THE PRODUCT ARE IMPORTANT SAFETY MESSAGES. READ THESE
MESSAGES CAREFULLY.
WARNING: FOR YOUR PROTECTION DO NOT CONNECT
THE POUCH LAMINATOR TO ELECTRICAL POWER UNTIL
YOU READ THESE INSTRUCTIONS COMPLETELY. KEEP
THESE INSTRUCTIONS IN A CONVENIENT LOCATION FOR
FUTURE REFERENCE. TO GUARD AGAINST INJURY, THE
FOLLOWING BASIC SAFETY PRECAUTIONS MUST BE
OBSERVED IN THE SET-UP AND USE OF THIS PRODUCT.
m
THE SAFETY ALERT SYMBOL PRECEDES EACH SAFETY
MESSAGE IN THIS INSTRUCTION MANUAL.
m
THIS SYMBOL INDICATES A POTENTIAL PERSONAL
SAFETY HAZARD THAT COULD HURT YOU OR OTHERS,
AS WELL AS CAUSE PRODUCT DAMAGE OR PROPERTY
DAMAGE.
General safeguards
• Use the unit only for its intended purposes of laminating documents.
THIS WARNING IS FOUND ON THE PRODUCT.
• Do not place anything in the throat opening of the laminator other than
pouches/documents.
WARNING
cm
Electrical shock hazard.
• Place unit on a secure, stable work area to prevent the unit from
falling and possibly causing personal injury and damage to the unit.
Do not open. No user
servicable parts inside.
Refer servicing to qualified
service personnel.
• Follow all warnings and instructions marked on the unit.
• The socket outlet shall be installed near the equipment and shall be
easily accessible.
• Do not attempt single side lamination, this will destroy the laminator.
• Do not block the vent slots, this will cause the laminator to overheat.
This safety message means that you could be seriously hurt or killed if
you open the product and expose yourself to hazardous voltage.
The following ISO and IEC symbols appear on this product, and their
meanings are as follows:
Electrical safeguards
• The unit must be connected to a supply voltage corresponding to the
electrical rating shown on the unit.
On / Off
Release
Cold
Heat
• Unplug the unit before moving it, or when it is not in use for an
extended period of time.
• Do not operate with a damaged supply cord or plug. Do not alter the
attachment plug. The plug is configured for the appropriate electrical
supply.
Special notice
• Do not overload electrical outlets beyond their capacity; fire or
electrical shock could result.
Thank you, for your recent purchase of a GBC Pouch Laminator. Your
new laminator may emit a slight odour during the initial stage of
operation. It is normal and will diminish after several hours of operation.
• The unit is intended for indoor use only.
• Never push objects through the cabinet slots. Do not spill liquid of any
kind on this product.
Cleaning
• Close supervision is required when this product is used near children.
Caution: Unplug this product before cleaning.
m• Wipe exterior only with a damp cloth. Do not use detergents
or solvents.
Service
• Do not use aerosol dusters or cleaners.
• Do not spray anything into the machine.
• Do not attempt to service or repair the pouch laminator yourself.
Unplug the unit and contact an authorised ACCO Brands Europe
service representative for any required repairs.
Specifications
GBC HeatSeal H212
GBC HeatSeal H312
230V / 50Hz / 2Amps / 500W
476x173x117mm
3.9kg
Electrical
230V / 50hZ / 2Amps / 500W
400 x 173 x 117.5mm
3.1kg
Machine Dimensions
Machine Weight
Maximum Pouch Width
Maximum Pouch Thickness
Maximum Thru-put Thickness
Warm-Up Time (2 x 75 mic)
241mm
318mm
2 x 125 mic (Total 250)
0.8mm
2 x 125 mic (Total 250)
0.8mm
5 minutes
5 minutes
ꢀ
G
Important: Before operating your new laminator, lift up the exit tray located at the rear of the machine and lock it in place (fig. 1).
Operation, hot lamination
1
2
4
5
Connect power cord to appropriate power source.
A series of four beeps will be heard when laminator reaches
operating temperature.
Push the power button to turn the power “ON” (fig. 2). The
indicator will glow red.
Position the document to be laminated into a GBC laminating pouch,
so that the document is aligned to the folded sealed edge and the
right and left borders are equal (fig. 4).
3
Using the lamination guidelines (fig. 3), select the appropriate
temperature setting for the pouch gauge thickness and material you
are laminating.
6
7
Insert the pouch and its contents straight into the machine, leading
with the folded edge.
• If the laminated item appears to be cloudy, it means that the
laminator temperature is not hot enough. Allow the laminator to
heat for a few more minutes then run the pouch through again.
The laminated item will automatically exit the rear of the machine.
After the pouch has stopped moving, immediately place it on a flat
surface to cool for one minute before handling (fig. 5).
• If the laminated item is wavy, the TEMPERATURE is too hot. Verify
temperature selector is set at the appropriate temperature.
8
If you have finished laminating, push the switch to turn “OFF” the
machine.
• Always allow sufficient time for the laminator to adjust to changes
in temperature setting.
DO NOT LAMINATE AN EMPTY POUCH
Operation, cold lamination
1
4
5
Connect power cord to appropriate power source.
A series of four beeps will be heard when the laminator is ready to
use.
2
3
Rotate the temperature dial to the “cold” position (fig. 2).
Use and laminate your GBC cold pouch.
(Pressure sensitive—non-thermal laminating pouch)
Push the power button to turn the power “ON” (fig. 2), the
indicator light will glow red.
Release lever
4
5
How to use the release lever.
Clean the rollers by running the cleaning sheet supplied with the
laminator through the machine 2 or 3 times in the hot operation
mode (red zone on temperature dial). If you do not have this sheet,
use a similar cardboard sheet that fits the width of the laminator.
1
2
If pouch jams or is fed improperly, turn off the laminator immediately.
Press the release lever down to release the motor from the rollers
(fig. 6).
Continue laminating.
3
Pull your document back out of the laminator while pressing the
release lever down (fig. 7).
Helpful lamination hints
1
3
4
Temperature setting Guidelines:
Do not attempt to do single sided lamination. This will destroy the
laminator.
When laminating thin paper with light ink coverage, set the
temperature dial at the low end of the range. Thick paper and heavy
ink coverage require higher settings. Temperature settings will vary
due to the finish, chemistry and heat absorption properties of the
material being laminated.
As soon as the lamination is completed, remove from the rear of the
machine and place on a cool flat surface for cooling to prevent the
pouch from curling.
5
Do not block the vent slots, this will cause the laminator to overheat.
2
Before laminating important or unique documents always run a test
pouch through the laminator using a similar type document.
Guarantee
Operation of this machine is guaranteed for two years from date of
purchase, subject to normal use. Within the guarantee period, ACCO
Brands Europe will at its own discretion either repair or replace the
defective machine free of charge. Defects due to misuse or use for
inappropriate purposes are not covered under the guarantee. Proof
of date of purchase will be required. Repairs or alterations made by
persons not authorised by ACCO Brands Europe will invalidate the
guarantee. It is our aim to ensure that our products perform to the
specifications stated. This guarantee does not affect the legal rights
which consumers have under applicable national legislation governing
the sale of goods.
Register this product online at www.accoeurope.com
ꢁ
Service
G
ACCO Service Division
Freepost 193, Hereward Rise, Halesowen, West Midlands, B62 8AN.
N
I
Sannum & Stang
Gladengveien 16 0661 Oslo.
Tel: +4722685940, Fax: +4722686730, e-mail: [email protected]
ACCO UK Sales International
Oxford Road, Aylesbury, HP21 8SZ.
Tel: 00 44 1296 397444, Fax: 00 44 1296 311000
ACCO Italia Spa
Via Nenni 13, Settimo Torinese (TO) Via Regio Parco 10B/bis.
Tel: 011 896 11 11, Fax: 011 896 11 12
IRE
F
O
B
D
ACCO France
o
ACCO-Rexel Ltd
Clonshaugh Business & Technology Park, Clonshaugh Dublin 17.
Tel: 01 816 4300, Fax: 01 816 4302
Service Aprés-Vente, 8 Rue du 19 Mars 1962, 21601 Longvic, Cedex BP7/ZI.
Tel: 0802 872 356, Fax: 03 80 68 60 49
ACCO Benelux
Peppelkade 64, 3992AK Houten.
Q
S
ACCO Polska Sp. z o.o.
Al-Jerozolimskie 184, 02-486 Warszawa.
Tel: +42 22 570 18 01, Fax: +48 22 570 18 33
ACCO Benelux (Technische Dienst)
Peppelkade 64, 3992AK Houten, Nederland.
ACCO Nordic Region
Kontor 1, i norden AB Kanalvägen 16 194 61 Upplands Väsby.
Tel: 08 444 5191, Fax: 08 444 5199
FI
o
ACCO Deutschland
H ATernl:o+ld4s9tra-s7s1e851,/7838671-146S0c,oFranxd:o+rf4,9Ge-r7m1a8n1y./887-165
Somen Huoltopalvelu oy
Kanaamouka 1 00360 Helsinki. Tel: 956 050 510, Fax: 956 050 500
RUS
o
E
CZ
o
A
S
XERTEC a.s.
P AIsCaaCcOPIebrearli1a9S, L28820 Coslada (Madrid). Tel: 91 669 9391, Fax: 91 672 07 11
U Továren 770/1b, 102 00, Praha 10.
g
Oddi
Höfdabakka 3-7 IS-112 Reykjavik. Tel: 00354 515 5000, Fax: 00354 515 5101
ACCO Österreich
Sallmann Bürotechnik GmbH, Esshaverstrasse 16, 5020 Salzburg.
Tel: 0662 4345 160, Fax: 0662 4345 164, e-mail: [email protected]
T
Eraysan
Ankara Cad N.129, Sirkeci, Istanbul.
Tel: 0090 212 6591686, Fax: 0090 212 5226992, [email protected]
ACCO Schweiz
AUS
o
ACCO Australia Pty.
Level 2 Building B, 8 Lord Street, Botany. NSW. Australia 2019.
Tel: 2 9700 0180, Fax: 2 9700 0195
ABC Bürotechnik AG, Winkelbüel 4, 6043 Adligenswil.
Tel: 041 375 6060, Fax: 041 375 6061,
e-mail: [email protected]
c
Mailtech
Baldersbaekvej 8B 2635 Ishoj.
Tel: 045 43 73 37 37, Fax: 0045 43 73 73 37 07, e-mail: [email protected]
ACCO Brands Europe
Oxford House
Aylesbury HP21 8SZ
United Kingdom
Ref: H212H312/5276
Issue: 1 (01/07)
|