™
ISBM71
iPod Interface for BMW
Instruction Manual
PROFESSIONAL INSTALLATION
STRONGLY ADVISED
IMPORTANT NOTE
iPod Firmware MUST be updated BEFORE any other step is taken.
Otherwise, the iPod will not operate properly. See page 1 for further details.
Peripheral Electronics®,
a division of AAMP of America™
13160 56th Court Clearwater, Florida 33760
866-788-4237 in the US or 727-572-9255 ext.262 for international calls
©2005 AAMP™ of Florida, Inc.
Chapter 1- Getting Started
1.1 Introduction
Thank you for purchasing Peripheral Electronics’® iSimple BMW interface. The
iSimple BMW interface is designed to provide endless hours of listening pleasure
through your vehicles’ factory radios. To ensure that your iPod performs correctly
in your car, we recommend that you read this entire manual before attempting
installation of the iSimple BMW interface.
The iSimple BMW interface will allow you to connect your iPod to a factory radio
that has the ability to control a CD changer. The iSimple BMW is designed to be
used with Generation 3, 4, Mini and Photo iPods.
1.2 Precautions (Important, Please Read)
UPDATING iPod FIRMWARE
For proper operation of the iSimple BMW interface, your iPod must be updated
with the most recent version of Firmware from Apple. This is done on your com-
load/. Follow the directions on the website to complete the download. There is no
charge for this update.
PREVENTING DAMAGE TO YOUR VEHICLE OR iPod.
To eliminate the risk of an electrical short, we recommend disconnecting the car
battery in most vehicles, except in the following situations:
• Vehicles equipped with on-board navigation should not have the car’s battery
disconnected. Doing so may cause loss of memory settings. These settings
would then have to be reprogrammed by an authorized car dealer for a fee to
be paid by the vehicle’s owner. For these vehicles, we recommend extreme
caution when handling exposed 12V power or ground wires/connectors.
•Vehicles that incorporate a security-code protecting the radio. If the car’s battery
or the radio’s power plugs are disconnected, the radio will not operate without
re-entering the security-code. If you have access to the security-code, feel
comfortable disconnecting the battery and the radio’s power connectors. Other
wise, do not disconnect the battery and exercise extreme caution while handling
exposed 12V power or ground wires/connectors.
PROPER MOUNTING LOCATION
Securely install the interface in a location free from; heat, humidity, moving parts or
direct sunlight. Beware of hot-air flow from your vehicle’s climate control system.
We recommend securing the interface to a suitable location, free of sharp metal
edges, using; double sided tape, Velcro or wire ties.
1
Docking cable
Vehicle specific harness
iSimple BMW interface
1.3 Programming the iSimple BMW Interface
Now that you have identified the correct harness and dip-switch configuration us-
ing the application guide, it is now time to program the interface.
To program the interface, set the dip-switches located on the side of the interface
(see Fig.1 below) to the congfiguration listed below. Switches are in their default
setting of “off” in the up position and are turned “on” when switched down. Refer to
the chart on the bottom of this page.
This programs the iSimple BMW interface to the vehicle it is being installed in. The
dip-switches MUST be set before the interface is plugged into the vehicle. Otherwise
the iSimple BMW interface will not work correctly.
Dip Switch Configuration Chart
BRAND MODE HARNESS
1
2
3
4
5
6
7
8
Vehicle
CDC or
BMW
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
specific
Changer
harness
Fig.1 Side view of Interface with dip switches
1 2
DIP
3
4
5
6
7
8
ON
2
Chapter 2- General Installation
2.1 Installation at CD Changer
The location of these CD changer cables will vary by vehicle. Some common locations of
these cables are in the trunk, behind the glove box, and in or under a center console.
2.2 Pre-Installation Checklist
At this time and before beginning the installation:
• Your iPod’s Firmware should have been updated. (section 1.2)
• You should have your radio’s security code.(when applicable, see section 1.2)
• The dip-switches on the interface should have been set with the proper configuration.
(see section 1.3)
• You should have in your possession the correct harness for your vehicle. (see sec. 1.3)
• You have determined your installation location. (see section 2.1)
If any of these steps has not been taken, STOP. Only when ALL of these steps have been
taken should you proceed with the rest of the installation.
2.3 Installation at the CD Changer Location
In this section you will learn how to install the iSimple BMW interface in the factory CD changer
location. If your vehicle is equipped with a factory CD changer you will need to disconnect it from
the factory pre-run harness in order to connect the iSimple BMW interface. If your vehicle is not
equipped with a factory CD changer, you will need to locate the factory pre-run harness. This may
involve the removal of the; center console, glove box, or carpeted side panels in the trunk. Please
consult your vehicle’s dealership or a local car audio professional for instruction or assistance with
locating the factory CD changer connection if necessary.
1. Connect your vehicle specific Harness to the factory pre-run CD changer harness in the vehicle.
2. Make any necessary wiring connections on your vehicle specific harness.
3. Now that the interface is connected to the radio, you will need to test the operation of the interface
before permanently running the iPod docking cable or re-assembling the dash. First, connect the
iPod cable to the iPod. The iPod should indicate that it is being charged. Turn on the factory radio
and press the button that would activate the factory CD changer to select the iPod. It may take up
to three minutes for the interface to initialize to the radio (this only happens the very first time you
select the iPod). Once the iPod has been selected, press Play on the iPod. You should be able to
hear the music on your iPod through your factory radio. Now press the “Next Track” button on the
radio. The iPod should change to the next song on the iPod. By pressing the “Previous Track” but-
ton on the radio the iPod should change to the previous song. With the operation of the interface
confirmed, you may continue with the installation. If you experience difficulties in operation, please
see our troubleshooting chart in section 3.2.
4. Decide on a convenient location to mount your iPod.
5. Run the docking cable from the interface to the desired mounting location. Use caution to not cut,
pinch, or crimp the cable during this step. Avoid moving parts, vehicle wiring harnesses and areas
of excessive heat when routing the cable.
6. Secure the interface in the vehicle using; double sided tape, Velcro or wire ties. Make sure to
check for proper clearance and avoid moving parts. Take into account the size of the interface and
the wire harness and do not force the interface and harness into a space that is too tight, damage
to the harness may result.
7. Now that the interface is secured and the docking cable has been run, you are ready to enjoy
your iPod in your vehicle!
3
Chapter 3- Operation
3.1 Operation
SELECTING THE IPOD
To select the iPod from the radio, press the button that would normally activate
the factory CD changer. The iSimple BMW interface is accessed like a BMW CD
changer, In these cases you will press the appropriate activation button. Some
radio models require pressing the “Seek >” button once, after pressing the CD
button. Yet, it may also be necessary to press Play on the iPod itself to begin
playback. In some cases, if it is the first time selecting the iPod from the radio it
may take up to three minutes for the iSimple BMW interface to initialize.
CONTROLLING THE IPOD FROM THE RADIO
With the iSimple BMW interface, the radio will control the iPod as if it were a fac-
tory CD changer. Therefore, operation will be done by using the same buttons
you would use to control a factory CD changer. For more details on your particu-
lar radio, consult your vehicle’s owner’s manual.
The iSimple BMW interface allows you to skip songs forward and backwards and
also to fast forward and rewind through a particular song. In general, most radios
will utilize “seek” or “track” buttons to control these functions.
CONTROLING THE IPOD FROM THE IPOD
The iSimple BMW interface allows you to keep full control of the iPod from the
click wheel. You can browse files and change playlist on the iPod. You can also
skip songs forward and backwards from the iPod. The iSimple BMW interface
does not disable any functionality of the iPod!
RADIO DISPLAY DURING IPOD OPERTION
Some factory radio’s may show DISC and TRACK numbers on the display of the
radio. The iSimple BMW interface does not send any information from the iPod to
the radio. This means that the DISC and TRACK numbers shown on the display
will not and can not reflect the song number on the iPod due to the complex
nature of the music library. Some factory radio’s may flash zero’s on the display
of the radio, or toggle back and forth between 1:00 and 2:00. All these are normal
behaviors and do not represent a malfunction.
CONTROLING THE IPOD FROM THE STEERING WHEEL CONTROLS
If your vehicle’s steering wheel controls have the ability to select track and control
the forward and rewind functions of your factory CD changer, then they will also
control these same functions on the iPod.
4
3.2 Trouble Shooting
Symptom
No Power
Cause
Remedy
Blown fuse in vehicle fuse
block.
Replace fuse with same
amp rating. If the fuse
blows again, call tech
support.
No Power
Bad connection
Check cable and wiring
connection.
Alternator noise is heard
(Changes with Engine RPM) ground loop
Improper wiring creates a
Install a Ground loop isola-
tor or seek professional
service from a local car
audio shop.
You can hear music from
the iPod but you cant con-
trol it from the radio.
The Firmware on the iPod
may not be updated.
Update the Firmware on
the iPod. See section 1.2
of this manual.
Radio is not recognizing
iSimple BMW interface
Bad cables or cables are
not connected properly
between converter box and
car radio
Check connection and
cables, push in firmly.
Radio is not recognizing
iSimple BMW interface
Wrong configuration on the
interface
Select the right pconfigu-
ration for your car. (See
section 1.5)
iPod Audio is Low or
Distorted
iSimple BMW interface is
connected with an external
CD changer or other exter-
nal factory audio source
Disconnect the factory
external audio source.
For consumer technical support call:
866-788-4237 in the US or 727-572-9255 ext.262 for international calls
Hours: 9:30 am-6:00 pm E.S.T. MON - FRI
5
3.3 Warranty
One Year Limited Warranty
The quality controls used in the manufacture of this product will ensure your satisfaction.
This warranty applies only to the original purchaser of this product from an authorized
Peripheral Elecronics dealer.
This warranty covers any supplied or manufactured parts of this product that, upon inspec-
tion by Peripheral Electronics authorized personnel, is found to have failed in normal use
due to defects in material or workmanship. This warranty does not apply to installation
expenses.
Attempting to service or modify this unit, operating this unit under conditions other than the
recommended voltage will render this WARRANTY VOID.
Unless otherwise prescribed by law, Peripheral Electronics shall not be liable for any per-
sonal injury, property damage and or any incidental or consequential damages of any kind
(including water damage) resulting from malfunctions, defects, misuse, improper installation
or alteration of this product.
All parts of this Peripheral Electronics product are guaranteed for a period of 1 year as
follows:
Within the first 12 months from date of purchase, subject to the conditions above, Peripher-
al Electronics will repair or replace the product at their discretion, if it is defective in material
or workmanship providing it is returned to an Authorized Peripheral Electronic’s Dealer, with
PROOF OF PURCHASE from an authorized Peripheral Elecronics dealer.
3.4 Warning:
This equipment may be reset by unintentional electrostatic discharge during operation.
Exposure to direct sunlight or extreme heat may cause damage or malfunction.
3.5 FCC Class B Radio Frequency
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television recption, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
1. Reorientate or relocate the receiving antenna.
2. Increase the separation between the equipment and reciever.
3. Connect the equipment into an outlet on a circuit differant from that of which
the reciever is connected.
4. Consult the dealer or an experienced radio / television technical for help
Notice : The changes or modifications not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment.
6
™
Peripheral Electronics®,
a division of AAMP of America™
13160 56th Court Clearwater, Florida 33760
866-788-4237 in the US or 727-572-9255 ext.262 for international calls
©2005 AAMP™ of Florida, Inc.
|