8214/8514/07187
Respirator N95 Particulate
3M recommended for welding on stainless steel, aluminum,
galvanized steel, and other applications where ozone and
nuisance organic vapors* may be present.
User Instructions
(Keep insert for reference)
Distributed by:
TM
.com
(888) 933-0100
1
Use Limitations:
1. This respirator does not supply oxygen. Do not use in atmospheres containing less than
19.5% oxygen.
2. Do not use when concentrations of contaminants are immediately dangerous to life and health, are
unknown or when concentrations exceed 10 times the permissible exposure limit (PEL) or according
to specific OSHA standards or applicable government regulations, whichever is lower.
3. Do not alter, abuse or misuse this respirator.
4. Do not use with beards or other facial hair or other conditions that prevent a good seal between the
face and the sealing surface of the respirator.
Time Use Limitations:
1. If respirator becomes damaged, soiled, or breathing becomes difficult, leave the contaminated area
immediately and replace the respirator.
2. If used for ozone protection, replace respirator in accordance with an established change schedule, or
earlier if smell, taste or irritation from contaminants is detected.
Fitting Instructions:
Must be followed each time respirator is worn.
1. Thread the top elastic strap through the top buckle. Repeat for the bottom elastic strap. Place the
bottom elastic strap around the head, just below the ears. Untwist the strap.
Diagram 1
3
2. Pull the top strap over your head, resting it above the ears at the top back of your head. Untwist the
strap.
Diagram 2
3. Adjust the strap tension by pulling the straps as shown (3a). Strap tension may be decreased without
removing respirator from the head by pushing out on the back of the buckle (3b).
Diagram 3a
Diagram 3b
4. Place your fingertips from both hands at the top of the metal nosepiece. Using two hands, mold the
nose area to the shape of your nose by pushing inward while moving your fingertips down both sides
of the nosepiece.
Pinching the nosepiece using one hand may result in improper fit and less effective respirator
performance. Use two hands.
Diagram 4
4
5. Perform a User Seal Check prior to each wearing. To check the respirator-to-face seal, cover the front
of the respirator completely with both hands, being careful not to disturb the position of the respirator.
Inhale sharply. A negative pressure should be felt inside the respirator. If any leakage is detected,
readjust the position of the respirator according to Steps #3 and #4.
If you CANNOT achieve a proper seal DO NOT enter the contaminated area. See your supervisor.
Diagram 5
REMOVAL INSTRUCTIONS:
See step 3b of Fitting Instructions and decrease strap tension as described. Cup respirator in hand to
maintain position on face and pull bottom strap over head. Still holding respirator in position, pull top
strap over head and remove respirator.
5
NIOSH Approved: N95
At least 95% filtration efficiency against solid and liquid aerosols that do not contain oil.
This respirator contains no components made from natural rubber latex.
6
FOR MORE INFORMATION and assistance on 3M occupational health and environmental safety
products, contact your local 3M representative or call 3M OH&ESD Technical Service toll free in U.S.A.,
1-800-243-4630. In Canada, call Technical Service at 1-800-267-4414.
Exported by/Exporté par/
Exportado por:
3M Occupational Health and
Environmental Safety Division
3M Center, Building 235-2W-70
P.O. Box 33010
St. Paul, MN 55133-3010
©3M 2001
38-9017-4804-6
Assembled in U.S.A. from U.S.A. and imported
components.
Distributed by:
TM
.com
(888) 933-0100
7
|