3Com Network Router 5000 6000 User Manual

3COM ROUTER 5000/6000 FAMILY  
QUICK REFERENCE GUIDE  
Overview  
This Command Reference applies to the following Router 5000/6000 models running software version 3.0.  
Router 5012 (3C13701)  
Router 5232 (3C13751)  
Router 5642 (3C13755)  
Router 5682 (3C13701)  
Router 6040 (3C13840)  
Router 6080 (3C13880)  
About the Command Line Interface  
To use and navigate the command line interface of your unit, please refer to the following points for assistance:  
When initially accessing the command line interface, press Enter when prompted. The User View menu for the unit  
displays. This is indicated by the chevron brackets around the name of the unit at the prompt, for example,  
<router5000-xx> (where xx is either EI or SI).  
When in the System View menu, square brackets appear around the name of the unit at the prompt, for example,  
[router5000-xx].  
You must be in the System View menu to access the configurable CLI commands.  
Some commands can be entered directly at any prompt from anywhere in the interface.  
If you enter part of a command followed by a ? (with no space between), the CLI will show you all the commands  
that begin in that way.  
The term ‘view’ may be used interchangeably with the term ‘menu’.  
The undo command is placed before the command you wish to undo, for example, undo setauthentication password.  
<CTRL-A> places the cursor back to the start of the command line.  
Enter the first few characters of a command and press TAB to enter the full command without having to input the  
entire command (where there is only one command that starts with the entered characters).  
Use the Up Arrow key at the prompt to repeat the previous command string.  
Use the Delete key to delete the character after the cursor; the Backspace key deletes the character before the cursor.  
When entering physical port numbers, Enter the port number as x/0/z, where x is the unit number and z is the  
physical port number.  
Copyright © 2006, 2007 3Com Corporation. All rights reserved.  
www.3Com.com  
Part Number: 10016467 Rev. AA  
Published: October 2007  
 
3Com Router 5000/6000 Family  
Command Reference  
3
abr-summary  
Use the abr-summarycommand to configure the route aggregation on the area border router (ABR).  
OSPF Area view  
ISP Domain view  
System view  
access-limit  
acl-reflect timeout  
acl  
Use the access-limitcommand to configure a limit to the amount of supplicants in the current ISP domain.  
Use the acl-reflect timeoutcommand to set the global aging time of reflexive ACLs.  
Use the aclcommand to create an access control list and enter ACL view.  
System View  
acl  
Use the aclcommand to reference an ACL to control call-in and call-out of VTY (Telnet and SSH) users.  
Use the accountingcommand to configure an accounting scheme for the current ISP domain.  
User Interface view  
ISP Domain view  
accounting  
accounting  
Use the accountingcommand to set the IP address, port number and shared key for the primary and  
secondary RADIUS accounting servers.  
RADIUS Scheme view  
RADIUS Scheme view  
TACACS+ view  
accounting  
Use the accountingcommand to set the IP address, port number and shared key for the primary and  
secondary RADIUS accounting servers.  
accounting  
Use the accountingcommand to set the IP address, port number and shared key for the primary and  
secondary TACACS+ accounting servers.  
accounting commands  
accounting domain  
Use the accounting commandscommand to enable the system to start per-command accounting for  
terminal users logged into the user interface.  
User Interface view  
Use the accounting domaincommand to enable DHCP server accounting for addresses from the global  
DHCP address pools and configure a domain for DHCP accounting.  
DHCP Address Pool view  
accounting-on  
Use the accounting-on enablecommand to enable the user re-authentication at reboot function.  
Use the accounting optionalcommand to enable optional accounting.  
RADIUS view  
accounting optional  
ISP Domain view  
RADIUS view  
activate  
Use the activatecommand to activate the ADSL interface.  
Use the activatecommand to enable the G.SHDSL interface.  
ATM (ADSL) Interface view  
activate  
ATM (G.SHDSL) Interface view  
activation-key  
Use the activation-keycommand to define a shortcut key or key combination for starting a terminal  
session.  
User Interface view  
Voice Entity view  
address  
Use the addresscommand to configure the voice routing policy to the peer voice gateway.  
 
4
3Com Router 5000/6000 Family  
Command Reference  
address  
Use the addresscommand to configure a route to the peer voice gateway or assign an X.121 address for  
a destination host.  
Voice Entity view  
Voice Entity view  
address sip  
Use the address sipcommand to set routing policy for reaching the remote voice gateway (VG) to SIP.  
adsl standard  
adsl tx_attenuation  
adv-factor  
Use the adsl standardcommand to set the standard applied to the ADSL interface.  
ATM (ADSL) Interface view  
ATM (ADSL) Interface view  
Use the adsl tx_attenuationcommand to set attenuation value for ADSL transmit power.  
Use the adv-factorcommand to configure the advantage factor which is used to count Mos and ICPIF  
value in a jitter voice test.  
HWPing Test Group view  
aggregate  
aggregate  
Use the aggregatecommand to establish an aggregated record in the BGP routing table.  
Use the aggregatecommand to create a multicast aggregated record in the BGP routing table.  
BGP view  
Use the aggregatecommand without parameters to create one local aggregated route and set atomic  
aggregation attributes.  
IPv4 Multicast Subaddress Family view  
aging-time  
Use the aging-timecommand to configure SYN status waiting timeout value and FIN status waiting timeout  
value of TCP, session entry idle timeout value of TCP and UDP.  
ASPF Policy view  
ah authentication-algorithm  
Use the ah authentication-algorithmcommand to set the authentication algorithm adopted by  
Authentication Header protocol in IPSec proposal.  
Use the undo ah authentication-algorithmcommand to restore the default setting.  
IPSec Proposal view  
ahdsl annex  
Use the shdsl annexcommand to configure annex standard at an SHDSL interface. You cannot activate a  
link with different standard types at its two ends.  
ATM (G.SHDSL) Interface view  
alarm (CT3 Interface)  
alarm-threshold  
algorithm-suite  
allow l2tp  
Use the alarmcommand to enable the CT3 interface to detect/send alarm signals.  
CT3 Interface view  
Use the alarm-thresholdcommand to configure the alarm thresholds on the CT1/PRI interface as needed.  
CT1/PRI Interface view  
Use the algorithm-suitecommand to specify the algorithm suite used when a client registers.  
Dvpn-Class view  
Use the allow l2tpcommand to specify the name of the peer end of the tunnel on receiving call and the  
Virtual-Template it uses.  
L2TP Group view  
DLCI view  
annexg  
ani  
Use the annexgcommand to enable T1.617 Annext G on the frame relay interface for data transmission.  
Use the anicommand to enable or disable the terminating point to send the calling party information  
(service category and calling number) to the originating point during call connecting process.  
R2 CAS view  
 
3Com Router 5000/6000 Family  
Command Reference  
5
ani-offset  
Use the ani-offsetcommand to configure the number of digits of the called number to be collected prior  
to requesting the calling party information.  
R2 CAS view  
R2 CAS view  
answer  
Use the answercommand to configure whether the terminating point is required to send answer signal.  
apply access-vpn vpn-instance  
Use the apply access-vpn vpn-instancecommand to specify to search private network forwarding routes  
in vpn-name1, vpn-name2, vpn-name3, vpn-name4, vpn-name5, vpn-name6 (if they all  
exist)and forward packets after policy routing is enabled to satisfy route-policy.  
Route-Policy view  
apply as-path  
Use the apply as-pathcommand to specify the AS numbers to be added in front of the original AS path in  
route-policy.  
Routing Policy view  
Routing Policy view  
Routing Policy view  
Routing Policy view  
Route-Policy view  
Routing Policy view  
Route-Policy view  
Route-Policy view  
Route-Policy view  
Route-Policy view  
Route-Policy view  
apply community  
apply cost  
Use the apply communitycommand to set BGP community attributes in route-policy.  
Use the apply costcommand to set the route cost value of route information.  
Use the apply cost-typecommand to set the route cost type of route information.  
apply cost-type  
apply default output-interface  
Use the apply default output-interfacecommand to set default forwarding interface for packets.  
apply ip-address  
Use the apply ip-addresscommand to set the next hop address of route information.  
apply ip-address default next-hop  
Use the apply ip-address default next-hopcommand to set the default next hop of a packet.  
apply ip-address next-hop (for Multicast Policy Routing)  
Use the apply ip-addresscommand to configure the next hop IP address list in a route-node.  
apply ip-address next-hop (for Unicast Policy Routing)  
Use the apply ip-address next-hopcommand to set the packet next hop.  
apply ip-dscp  
apply ip-precedence  
apply isis  
Use the apply ip-dscpcommand to configure to modify the packet DSCP value matching the policy.  
Use the apply ip-precedencecommand to set precedence of IP packets.  
Use the apply isiscommand to apply the level of a matched route to be redistributed to Level-1, Level-2  
or Level-1-2.  
Routing Policy view  
Routing Policy view  
apply local-preference  
Use the apply local-preferencecommand to apply the local preference of route information.  
apply mpls-label  
Use the apply mpls-labelcommand to assign MPLS labels for public network routes that match  
route-policy filter conditions.  
Route-Policy view  
 
6
3Com Router 5000/6000 Family  
Command Reference  
apply origin  
Use the apply origincommand to set the routing source of BGP routing information.  
Routing Policy view  
apply output-interface (for Multicast Policy Routing)  
Use the apply output-interfacecommand to configure an outgoing interface list in a route-node.  
Route-Policy view  
Route-Policy view  
apply output-interface (for Unicast Policy Routing)  
Use the apply output-interfacecommand to set a packet forwarding interface.  
apply policy outbound  
Use the apply policy outboundcommand to set the frame relay virtual circuit queuing to CBQ  
(Class-Based Queuing).  
Frame Relay Class view  
Routing Policy view  
apply tag  
Use the apply tagcommand to set the tag area of OSPF route information.  
Use the areacommand to enter OSPF area view.  
area  
OSPF view  
OSPF Area view  
area  
Use the areacommand to configure the type of busy tone detection for FXO voice subscriber-line.  
Voice Subscriber-line view  
area-authentication-mode  
Use the area-authentication-modecommand to configure IS-IS to authenticate the received Level-1  
routing information packets (LSP, CSNP and PSNP), according to the pre-defined mode and password.  
IS-IS view  
Voice Entity view  
area-id (Voice Entity view)  
Use the area-idcommand to configure the area ID of voice GW.  
area-id (Voice GK Client view)  
Use the area-idcommand to configure the H.323 gateway area ID.  
Voice GK Client view  
arp check enable  
Use the arp check enablecommand to enable ARP entry check to have the device not learn the ARP  
entries with broadcast MAC addresses.  
System view  
Ethernet interface view  
Ethernet Interface view  
Ethernet Interface view  
arp-proxy enable  
arp security  
Use the arp-proxy enablecommand to enable proxy ARP on an interface.  
Use the arp securitycommand to disable dynamic ARP learning on an Ethernet interface.  
Use the arp security time-outcommand to configure the aging time of the authorized ARP entries.  
arp security time-out  
arp send-gratuitous-arp  
Use the arp send-gratuitous-arpcommand to enable sending gratuitous ARP packet on this interface  
periodically and set the sending period.  
Bridge Template view  
Ethernet Interface view  
Ethernet Subinterface view  
Gigabit Ethernet Interface view  
Gigabit Ethernet Subinterface view  
Virtual Ethernet interface view  
VLAN Interface view  
arp static  
Use the arp staticcommand to configure ARP mapping table.  
System view  
 
3Com Router 5000/6000 Family  
Command Reference  
7
arp timer aging  
Use the arp timer agingcommand to set the aging timer for dynamic ARP entries.  
System view  
OSPF view  
asbr-summary  
ascii  
Use the asbr-summarycommand to configure summarization of redistributed routes by OSPF.  
Use the asciicommand to set the type of the transmitted data to ASCII.  
FTP Client view  
aspf-policy  
Use the aspf-policycommand to define an ASPF policy. For a defined policy, the policy can be invoked  
through its policy number.  
System view  
async mode  
Use the async modecommand to set the operating mode of the asynchronous serial interface.  
Asynchronous Serial Interface view  
AUX Interface view  
AM Interface view  
async mode padpos  
Use the async mode padposcommand to configure a POSPAD access port.  
Asynchronous Serial Interface view  
AUX Interface view  
async mode pos  
Use the async mode pospos-numbercommand to create a POS access port in nontransparent  
transmission and permanent TCP connection mode.  
Asynchronous Serial Interface view  
AM Interface view  
FCM Interface view  
AUX Interface view  
async mode posapp  
Use the async mode posappcommand to configure the interface to operate in POS application mode.  
Asynchronous Serial Interface view  
AUX Interface view  
atm-class  
Use the atm-classcommand to apply a set of parameters (which are defined in ATM-Class) to an ATM  
interface or a PVC.  
Interface view  
PVC view  
atm class  
Use the atm classcommand to create an ATM-Class and enter the ATM-Class view.  
Use the atm-cttcommand to set all interfaces on a board to transparent transmission.  
System view  
atm-ctt  
ATM Interface view  
atm-link check  
Use the atm-link checkcommand to have the protocol state of the ATM P2P subinterface changes  
depending on whether the physical interface is up and whether a PVC is configured on the subinterface.  
ATM P2P Subinterface view  
authentication  
authentication  
Use the authenticationcommand to configure an authentication scheme for the current ISP domain.  
ISP Domain view  
Use the authenticationcommand to set the IP address, port number and shared key for the primary and  
secondary RADIUS authentication servers.  
RADIUS Scheme view  
authentication  
Use the authenticationcommand to set the IP address, port number and shared key for the primary and  
secondary TACACS+ authentication servers.  
TACACS+ view  
 
8
3Com Router 5000/6000 Family  
Command Reference  
authentication  
Use the authenticationcommand to enable user authentication and authorization for the access service  
number.  
Voice Access-Number view  
authentication  
Use the authenticationcommand to set the IP address, port number and shared key for the primary and  
secondary TACACS+ authentication servers.  
TACACS+ view  
authentication-algorithm  
Use the authentication-algorithmcommand to select the authentication algorithm for an IKE proposal.  
IKE Proposal view  
authentication-client method  
Use the authentication-client methodcommand to specify how the DVPN server that applies the DVPN  
policy authenticates clients. None, CHAP, and PAP are currently available.  
Dvpn-Policy view  
Voice AAA view  
authentication-did  
authentication-method  
authentication-mode  
Use the authentication-didcommand to enable authentication for all one-stage dial (direct dial) users.  
Use the authentication-methodcommand to select the authentication method used by an IKE proposal.  
Use the authentication-modecommand to set the authentication mode at login.  
IKE Proposal view  
Use the authentication-mode nonecommand to set the authentication mode to none, that is, no  
authentication at login.  
User Interface view  
OSPF Area view  
Dvpn-Class view  
authentication-mode  
Use the authentication-modecommand to configure one area of OSPF to support the authentication  
attribute.  
authentication-server method  
Use the authentication-server methodcommand to specify a client whether or not to authenticates the  
DVPN server it accesses.  
authentication super hwtacacs-scheme  
Use the authentication super hwtacacs-schemecommand to configure super authentication scheme for  
a domain.  
ISP Domain view  
ISP Domain view  
authorization  
authorization  
Use the authorizationcommand to configure an authorization scheme for the current ISP domain.  
Use the authorizationcommand to set the IP address, port number and shared key for the primary and  
secondary TACACS+ authorization servers.  
TACACS+ view  
Voice Entity view  
System view  
authorization-level  
auto-config  
Use the authorization-levelcommand to configure a local caller authorization level for the voice entity.  
Use the auto-configcommand to implement the auto-configoperation.  
auto-config enable  
auto-execute command  
Use the auto-config enablecommand to enable auto-config.  
System view  
Use the auto-execute commandcommand to set a command to be automatically executed.  
User Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
9
balance  
Use the balancecommand to configure the number of routes participating in BGP load balancing.  
BGP view  
System view  
band-based-sharing  
baudrate  
Use the band-based-sharingcommand to enable bandwidth-based unbalanced load sharing.  
Use the baudratecommand to set the baud rate of a serial interface.  
Use the bertcommand to set test error bit for line Bit.  
Serial Interface view  
CE3 interface view  
CT1/PRI Interface view  
CT3 Interface view  
System view  
bert  
bert (CT1/PRI Interface)  
Use the bertcommand to start a BERT test on the CT1/PRI interface.  
bert (CT3 Interface)  
Use the bertcommand to start a BERT test on the CT3 interface.  
bgp  
Use the bgpcommand to enable BGP and enter the BGP view.  
This command is used to enable and disable BGP as well as to specify the local AS number of BGP.  
bims boot request  
Use the bims boot requestcommand to enable the BIMS device to access the branch intelligent  
management system (BIMS) center at startup.  
System view  
bims device-id string  
Use the bims device-idcommand to configure the unique identifier of the BIMS device at the BIMS center.  
Use the bims enablecommand to enable BIMS.  
System view  
System view  
bims enable  
bims interval  
Use the bims intervalcommand to configure the interval for accessing the BIMS center. When the interval  
is set to 0, the BIMS device does not access the BIMS center regularly.  
System view  
System view  
System view  
bims ip address  
bims request  
bims-server  
Use the bims ip addresscommand to configure the IP address and port number of the BIMS center.  
Use the bims requestcommand to have the BIMS device access the BIMS center.  
Use the bims-servercommand to enable and configure BIMS option for a global address pool on the  
DHCP server.  
Global DHCP Address Pool view  
bims sharekey  
Use the bims sharekeycommand to configure the shared key between the BIMS device and the BIMS  
center.  
System view  
System view  
bims source ip-address  
Use the bims source ip-addresscommand to specify a source IP address for the packets sent by the  
BIMS device. It can be the IP address of a port on the router.  
bims specify-time  
Use the bims specify-timecommand to configure the BIMS device to access the BIMS center at the  
specified time and if desired, configure the device to access the BIMS center at regular intervals from then  
on during a specified period.  
System view  
 
10  
3Com Router 5000/6000 Family  
Command Reference  
binary  
Use the binarycommand to set data type to binary for file transfer.  
Use the boot bootromcommand to upgrade BootRom.  
FTP Client view  
System view  
System view  
System view  
boot bootrom  
boot bootrom  
bootfile backup  
bootfile dir  
Use the boot bootromcommand to upgrade BootRom.  
Use the bootfile backupcommand to specify the backup boot file.  
Use the bootfile dircommand to view information about all the boot files in the Flash, including file type,  
date, time, file size, and file name.  
System view  
System view  
System view  
System view  
bootfile main  
Use the bootfile maincommand to specify the main boot file.  
bridge aging-time  
Use the bridge aging-timecommand to configure the aging time of the dynamic address table.  
bridge bridge-set enable  
Use the bridgebridge-setenablecommand to enable the specified bridge set.  
bridge bridging  
Use the bridge bridgingcommand to enable the bridging function of a network layer protocol on a  
specified bridge set.  
System view  
System view  
System view  
System view  
bridge enable  
Use the bridge enablecommand to enable the bridging function.  
bridge learning  
bridge mac-address  
bridge routing  
Use the bridge learningcommand to enable forwarding by dynamic address table.  
Use the bridge mac-addresscommand to manually configure a static address table entry of bridge.  
Use the bridge routingcommand to enable the routing function of a specified bridge-set for the specified  
network protocol.  
System view  
System view  
bridge routing-enable  
Use the bridge routing-enablecommand to enable the routing function of the bridge.  
Use the bridge setcommand to add an interface to a bridge set.  
bridge-set  
Interface view  
Bridge Template view  
bridge-set (Ethernet Interface view)  
Use the bridge-set (in the Ethernet Interface view)command to add the Ethernet interface into the  
bridge.  
Ethernet Interface view  
bridge set (Synchronous Serial Interface view)  
Use the bridge-set (in Synchronous serial interface system view)command to add the  
synchronous serial interface encapsulated into SDLC into the bridge group.  
Synchronous Serial Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
11  
bridge-set stp enable  
Use the bridge-set stp enablecommand to disable STP on the port.  
Interface view  
Interface view  
Interface view  
System view  
System view  
System view  
System view  
System view  
bridge-set stp port pathcost  
Use the bridge-set stp port pathcostcommand to configure the path cost of the bridge port.  
bridge-set stp port priority  
Use the bridge-set stp port prioritycommand to configure the priority of the bridge port.  
bridge stp ieee  
Use the bridge stp ieeecommand to specify a bridge set to support IEEE STP.  
Use the bridge stp max-agecommand to set the Max Age timer on the bridge.  
Use the bridge stp prioritycommand to assign a priority to the bridge.  
bridge stp max-age  
bridge stp priority  
bridge stp timer forward-delay  
Use the bridge stp timer forward-delaycommand to set the Forward Delay timer on the bridge.  
bridge stp timer hello  
Use the bridge stp timer hellocommand to set the Hello Time timer on the bridge.  
bridge vlanid-transparent-transmit enable  
Use the bridge vlanid-transparent-transmit enablecommand to enable VLAN ID transparent  
transmission.  
Interface view  
broadcast-limit link  
Use the broadcast-limit linkcommand to configure the maximum number of links that the virtual  
template supports for sending multicast or broadcast packets.  
Virtual Template view  
Ethernet Port view  
PIM view  
broadcast suppression  
Use the broadcast-suppressioncommand to restrict the broadcast traffic size on the port.  
Use the bsr-policycommand to restrict the range for valid BSR, preventing BSR spoofing.  
bsr-policy  
bump  
Use the bumpcommand to configure the standby PVC that will take over when a specified PVC goes down.  
ATM Pvc-Group view  
busytone-t-th  
Use the busytone-t-thcommand to configure the threshold of busy tone detection.  
FXO Voice Subscriber-Line view  
FTP Client view  
bye  
Use the byecommand to disconnect from the remote FTP server and exit to user view.  
bye  
Use the byecommand to terminate the connection to the remote SFTP server and exit to system view as  
you would with the exitand quitcommands.  
SFTP Client view  
PIM view  
c-bsr  
c-rp  
Use the c-bsrcommand to configure a candidate BSR.  
Use the c-rpcommand to configure the router to advertise itself as a candidate RP to BSR.  
PIM view  
 
12  
3Com Router 5000/6000 Family  
Command Reference  
ca identifier  
Use the ca identifiercommand to specify the CA this device trusts and have the "name" CA bound with  
this device.  
PKI Domain view  
CE1/PRI Interface view  
ATM E1/T1 Interface view  
cable  
cable  
cable  
Use the cablecommand to set the cable length matching the CE1/PRI interface.  
Use the cablecommand to set the cable length of the ATM E1 interface.  
Use the cablecommand to configure the cable mode of ATM T3 cable, i.e., to set the distance between the  
router and the cable distribution frame.  
ATM T3 Interface view  
cable (CT1/PRI Interface)  
Use the cablecommand to set cable attenuation and length on a CT1/PRI interface to match the distance  
of the transmission line.  
CT1/PRI Interface view  
CT3 Interface view  
MSDP view  
cable (CT3 Interface)  
cache-sa-enable  
call-mode  
Use the cablecommand to configure the length of the cable with which a CT3 interface is connected.  
Use the cache-sa-enablecommand to enable the router to cache SA state.  
Use the call-modecommand to configure a call-mode for calls between local router and peer router.  
Voice Entity view  
callednumber receive-method  
Use the callednumber receive-methodcommand to enable the device to place a call immediately after all  
digits of the called number are collected or after a pound sign (#), the terminator, is received.  
Use the caller-permit command to configure the calling numbers that are permitted to call in.  
Use the carcommand to configure traffic monitoring for a behavior.  
Voice Access-Number view  
caller-permit  
Voice Entity view  
car  
Traffic Behavior view  
card-digit  
Use the card-digitcommand to configure the number of digits in a card number for an access service  
number.  
Voice Access-Number view  
cas  
cbs  
Use the cascommand to enter the R2 CAS view and digital E&M Signaling view.  
Use the cbscommand to set the committed burst size of frame relay virtual circuit.  
CE1/PRI Interface view  
Frame Relay Class view  
System view  
ccc interface out-interface  
Use the ccc interface out-interfacecommand to create a local CCC connection.  
ccc interface transmit-lsp receive-lsp  
Use the ccc interface transmit-lsp receive-lspcommand to create a remote CCC connection.  
System view  
cd  
Use the cdcommand to change the current path on the SFTP server. If you do not specify the remote-path  
argument, the current path is displayed.  
SFTP Client view  
 
3Com Router 5000/6000 Family  
Command Reference  
13  
cd  
Use the cdcommand to change the current working directory of the user to the specified directory.  
User view  
FTP Client view  
Voice AAA view  
SFTP Client view  
FTP Client view  
MPLS L2VPN view  
PVC view  
cd  
Use the cdcommand to change the current working directory path on the remote FTP server.  
Use the cdrcommand to configure the saving rule for call detail record.  
Use the cdupcommand to quit to the upper directory.  
cdr  
cdup  
cdup  
Use the cdupcommand to return from the current working directory path to the upper directory.  
Use the cecommand to create a CE or modify the CE range.  
ce  
cell-packing  
Use the cell-packingcommand to set the maximum number of cells to be packed in one PVC.  
certificate request entity  
Use the certificate request entitycommand to specify the name of the entity for certificate request.  
PKI Domain view  
certificate request from  
Use the certificate request fromcommand to choose between CA and RA to register for certificate  
request.  
PKI Domain view  
PKI Domain view  
certificate request mode  
Use the certificate request modecommand to decide between the manual or the auto request mode.  
certificate request polling  
Use the certificate request pollingcommand to specify the interval between two polls and the retry  
times.  
PKI Domain view  
PKI Domain view  
certificate request url  
Use the certificate request urlcommand to specify the server URL for certificate request through  
SCEP protocol. SCEP is a protocol specialized in the communication with authentication authorities.  
channel  
Use the channelcommand to add X.25 interface or XOT channel of one serial port to the current hunt group.  
X.25 Hunt Group view  
CE1/PRI Interface view  
CT1/PRI Interface view  
ISDN BRI Interface view  
RIP view  
channel-set (CE1/PRI Interface)  
Use the channel-setcommand to bundle some timeslots of a CE1/PRI interface into a channel-set.  
channel-set (CT1/PRI Interface)  
Use the channel-setcommand to bundle timeslots on the CT1/PRI interface into a channel-set.  
channel-set timeslot  
checkzero  
Use the channel-set timeslot command to configure a B channel for leased line service.  
Use the checkzerocommand to check the zero field of RIP-1 packet.  
cid display  
Use the cid displaycommand to enable caller identification display.  
Voice Subscriber-Line view  
 
14  
3Com Router 5000/6000 Family  
Command Reference  
cid enable  
Use the cid enablecommand to enable CID on the FXO interface.  
Voice Subscriber-Line view  
cid select-mode  
Use the cid select-modecommand to configure the route selection mode used by the calling party to set  
up VoFR calls.  
DLCI view  
cid send  
Use the cid sendcommand to enable the FXO or FXS module to send calling numbers to the IP side.  
Voice Subscriber-Line view  
cid type  
Use the cid typecommand to configure the format of transmitted information about the calling party.  
Voice Subscriber-Line view  
Frame Relay Class view  
Frame Relay Class view  
Policy view  
cir  
Use the circommand to set the CIR of frame relay virtual circuit.  
cir allow  
Use the cir allowcommand to set the CIR ALLOW of frame relay virtual circuit.  
Use the classifier behaviorcommand to specify the behavior for the class in the policy.  
classifier behavior  
clear-forward-ack  
Use the clear-forward-ackcommand to enable or disable the terminating point to respond by sending a  
clear-back signal when the originating point (calling party) disconnects a call.  
R2 CAS view  
System view  
System view  
clns enable  
Use the clns enablecommand to enable CLNS.  
clns erpacket enable  
Use the clns erpacket enablecommand to enable generation of error report packets.  
clns erpacket interval  
Use the clns erpacket intervalcommand to set the minimum interval to generate two successive error  
report packets.  
System view  
System view  
System view  
System view  
System view  
System view  
clns es-peer  
Use the clns es-peercommand to configure a static neighboring ES.  
Use the clns netcommand to assign an NET address to the IS.  
Use the clns rdpacket enablecommand to enable the router to send RD packets.  
clns net  
clns rdpacket enable  
clns rdpacket interval  
Use the clns rdpacket intervalcommand to set the minimum interval to generate RD packets.  
clns route-static  
Use the clns route-staticcommand to configure a static OSI route.  
clns timer rdpacket holding  
Use the clns timer rdpacket holdingcommand to set the holding time of the information a RD packet  
carries.  
System view  
clock  
Use the clockcommand to set the clock mode of the ATM E1/T1 interface.  
ATM E1/T1 Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
15  
clock  
Use the clockcommand to set the clock mode of ATM E3/T3 interface.  
ATM E3/T3 Interface view.  
ATM Interface view  
clock  
clock  
clock  
clock  
Use the clockcommand to set the clock mode on an ATM interface.  
Use the clockcommand to specify ATM interface to use internal transmission clock signal.  
Use the clockcommand to set the clock mode of the CPOS interface.  
Use the clockcommand to set the clock mode of the POS interface.  
ATM Master Interface view  
CPOS Interface view  
POS Interface view  
clock (CE1/PRI Interface)  
Use the clockcommand to set the clock mode on a CE1/PRI interface.  
CE1/PRI Interface view  
CE3 Interface view  
clock (CE3 Interface)  
clock (CT1/PRI Interface)  
Use the clockcommand to set clocking on the CT1/PRI interface.  
CT1/PRI Interface view  
CT3 Interface view  
Serial intervace view  
System view  
clock (CT3 Interface)  
Use the clockcommand to set the clock mode on the CT3 interface.  
clock (Serial Interface)  
Use the clockcommand to set clock selection mode for a synchronous serial interface.  
clock datetime  
Use the clock datetimecommand to set the current time and date of the router.  
clock summer-time  
Use the clock summer-timecommand to set the name, and starting and ending time of the daylight saving  
time.  
System view  
System view  
clock timezone  
Use the clock timezonecommand to set local time zone information.  
close  
Use the closecommand to terminate the connection to the remote FTP server, but remain in FTP client  
view.  
FTP Client view  
cng-on  
Use the cng-oncommand to enable comfort noise function.  
Voice Subscriber-Line view  
cngced-detection  
Use the cngced-detectioncommand to set the threshold parameters for CNG/CED signal detection.  
Voice Subscriber-Line view  
CE1/PRI Interface view  
CT1/PRI Interface view  
code (CEI/PRI Interface)  
Use the codecommand to set the line code format for a CE1/PRI interface.  
code (CT1/PRI Interface)  
Use the codecommand to set the line code format on the CT1/PRI interface.  
 
16  
3Com Router 5000/6000 Family  
Command Reference  
code nrzi  
Use the code nrzicommand to set the digital signal coding format to None-Return-to-Zero-Inverse (NRZI)  
for a synchronous serial interface.  
Synchronous Serial Interface view  
code nrzi  
Use the code nrzicommand to configure the NRZI encoding of the synchronous serial port.  
Synchronous Serial Interface System view  
System view  
command-alias enable  
command-alias mapping  
command-privilege  
Use the command-alias enablecommand to enable the command alias function.  
Use the command-alias mapping command to map an alias to a keyword.  
System view  
Use the command-privilege levelcommand to assign a command level to the commands in a specified  
view.  
System view  
common-name  
Use the common-namecommand to specify the common name of an entity, take User name for example.  
PKI Entity view  
compare-different-as-med  
Use the compare-different-as-medcommand to enable comparison of MED values of routes from  
neighbors residing in different ASs when determining the best route.  
BGP Unicast view  
BGP Multicast view  
VPNv4 view  
compression  
Use the compressioncommand to configure the voice coding method according to priority level.  
Use the confederation idcommand to configure confederation identifier.  
Voice Entity view  
BGP view  
confederation id  
confederation nonstandard  
Use the confederation nonstandardcommand, the router can be compatible with the AS confederation  
not adopting RFC1965.  
BGP view  
BGP view  
confederation peer-as  
Use the confederation peer-ascommand to specify the sub-ASs constituting a confederation.  
congestion-threshold  
Use the congestion-thresholdcommand to enable congestion management function of frame relay virtual  
circuit.  
Frame Relay Class view  
connection  
Use the connectioncommand to create a CE connection.  
MPLS L2VPN CE view  
connection-limit default  
Use the connection-limit defaultcommand to configure the action when the limit policy is not available.  
System view  
System view  
System view  
System view  
connection-limit default amount  
Use the connection-limit default amountcommand to set default threshold for connection limit.  
connection-limit enable  
Use the connection-limit enablecommand to enable the connection limit function.  
connection-limit policy  
Use the connection-limit policycommand to create connection limit policy and enter its view.  
 
3Com Router 5000/6000 Family  
Command Reference  
17  
controller cpos  
Use the controller cposcommand to enter CPOS interface view.  
System view  
System view  
controller e1  
controller e3  
controller t1  
controller t3  
copy  
Use the controller e1command to enter CE1/PRI interface view.  
Use the controller e3command to enter the CE3 interface view.  
Use the controller t1command to enter a CT1/PRI interface view.  
Use the controller t3command to enter the CT3 interface view.  
Use the copycommand to copy a file.  
System view  
System view  
System view  
User view  
cost-style  
count  
Use the cost-stylecommand to set the cost type of an IS-IS packet received/sent by the router.  
Use the countcommand to configure the number of packets to be sent for each test.  
IS-IS view  
HWPing Test Group view  
country  
Use the countrycommand to specify the code of the country to which the entity belongs. It is a standard  
2-byte code, e.g., CN for China.  
PKI Entity view  
country-code  
Use the country-codecommand to configure the coding format of the modem connected to the serial  
interface.  
Asynchronous Serial Interface view,  
AM Interface view  
cptone  
Use the cptonecommand to set the prompt tone played on the current voice subscriber-line to the specified  
country mode.  
Voice Subscriber-Line view  
cpu-usage cycle  
Use the cpu-usage cyclecommand to set the CPU usage statistic interval.  
Use the crccommand to set the CRC length on the POS interface.  
Use the crccommand to configure CRC mode of the serial interface formed by CE1.  
Use the crccommand to configure CRC mode of the serial interface formed by CE3.  
Use the crccommand to configure CRC mode of the serial interface formed by CT1.  
Use the crccommand to configure CRC mode of the serial interface formed by CT3.  
System view  
crc  
POS Interface view  
crc  
Synchronous Serial Interface view  
Synchronous Serial Interface view  
Synchronous Serial Interface view  
Synchronous Serial Interface view  
PKI Domain view  
crc  
crc  
crc  
crl check disable  
Use the crl check disablecommand to disable CRL checking.  
 
18  
3Com Router 5000/6000 Family  
Command Reference  
crl update-period  
Use the crl update-periodcommand to specify the update period of CRL, which is the interval between  
local downloads of CRLs from CRL access server.  
PKI Domain view  
PKI Domain view  
crl url  
Use the crl urlcommand to specify the distribution point URL for CRL.  
crp-policy  
Use the crp-policycommand to restrict the range for valid C-RP and the group range served by each  
C-RP, preventing C-RP cheating.  
PIM view  
CT3 Interface view  
BGP view  
ct1 alarm  
Use the t1 alarmcommand to enable the specified T1 line on the CT3 interface to detect/send alarm  
signals.  
dampening  
Use the dampeningcommand to make BGP route dampening valid or modify various BGP route dampening  
parameters.  
data algorithm-suite  
Use the data algorithm-suitecommand to specify the algorithm suite used by IPSec SA (security  
association) to forward data.  
Dvpn-Policy view  
data-coding (CT1/PRI Interface)  
Use the data-coding normalcommand to disable user data inversion on the CT1/PRI interface.  
Use the data-coding invertedcommand to enable user data inversion on the CT1/PRI interface.  
CT1/PRI Interface view  
data-flow-format  
data-flow-format  
Use the data-flow-formatcommand to configure the unit in which data flows are sent to a RADIUS Server.  
Use the data-flow-formatcommand to configure the unit of data flows sent to the TACACS server.  
RADIUS view  
TACACS+ view  
data ipsec-sa duration time-base  
Use the data ipsec-sa duration time-basecommand to set the lifetime of the IPSec SA used to encrypt  
DVPN data.  
Dvpn-Policy view  
User Interface view  
databits  
Use the databitscommand to set data bits on the user interface.  
Use the datafillcommand to configure the data for padding test packets.  
Use the datasizecommand to configure the size of test packets.  
datafill  
HWPing Test Group view  
HWPing Test Group view  
datasize  
datetime local  
Use the datetime localcommand to configure the Datetime information element in the Connect message  
to use local time in an ISDN call.  
PRI and BSV Voice Interface Voice Subscriber Line view  
ddns domainname  
ddns password  
Use the ddns domainnamecommand to configure a domain name whose domain name-to-IP address  
mapping on DNS needs update by using the service of the DDNS service provider.  
DDNS Configuration view  
Use the ddns passwordcommand to configure a password for accessing the DDNS service provider.  
DDNS Configuration view  
 
3Com Router 5000/6000 Family  
Command Reference  
19  
ddns refresh  
Use the ddns refreshcommand to request the DDNS service provider to notify the DNS server that the  
bound IP address of the domain name specified by the ddns domainnamecommand has changed.  
DDNS Configuration view  
ddns server  
Use the ddns-servercommand to specify a DDNS service provider and enter its view. At present, only  
3322.org is available.  
System view  
ddns source interface  
Use the ddns source-interfacecommand to configure the interface used for accessing the DDNS service  
provider.  
DDNS Configuration view  
ddns username  
Use the ddns usernamecommand to configure a user name for accessing the DDNS service provider.  
DDNS Configuration view  
FTP Client view  
User view  
debugging  
Use the debuggingcommand to enable debugging.  
debugging  
Use the debuggingcommand to enable system debugging.  
debugging l2tp  
debugging arp packet  
debugging aspf  
debugging atm all  
debugging atm error  
debugging atm event  
debugging atm packet  
debugging bgp  
Use the debugging l2tpcommand to enable L2TP debugging.  
System view  
User view  
Use the debugging arp packetcommand to enable ARP packets debugging.  
Use the debugging aspfcommand to enable ASPF debugging function.  
Use the debugging atm allcommand to enable all the debugging switches of ATM.  
Use the debugging atm errorcommand to enable the error debugging of ATM.  
Use the debugging atm eventcommand to enable the event debugging of ATM.  
Use the debugging atm packetcommand to enable the packet debugging of ATM.  
Use the debugging bgpcommand to enable debugging of specified BGP packets and events.  
User view  
User view  
User view  
User view  
User view  
User view  
debugging bgp mp-update  
Use the debugging bgp mp-updatecommand to enable MBGP Update packet debugging.  
User view  
debugging bims all  
debugging bridge  
Use the debugging bims allcommand to enable BIMS debugging.  
User view  
Use the debugging bridgecommand to enable the debugging function of a bridge set.  
User view  
debugging clns clnp  
Use the debugging clns clnpcommand to enable debugging for CLNS packets to display the contents of  
all received/transmitted CLNP packets.  
User view  
 
20  
3Com Router 5000/6000 Family  
Command Reference  
debugging clns echo  
debugging clns rd  
Use the debugging clns echocommand to enable debugging for Echo packets.  
Use the debugging clns rdcommand to enable debugging for RD packets.  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
System view  
User view  
debugging clns routing  
Use the debugging clns routingcommand to enable debugging for Layer 3 routing tables.  
debugging connection-limit  
Use the debugging connection-limitcommand to enable connection limit debugging.  
debugging detect-group  
Use the debugging detect-groupcommand to enable auto detect debugging.  
debugging dhcp client  
debugging dhcp relay  
debugging dhcp server  
debugging dialer  
Use the debugging dhcp clientcommand to enable debugging on the DHCP client.  
Use the debugging dhcp relaycommand to enable debugging on the DHCP-relay module.  
Use the debugging dhcp servercommand to enable debugging on the DHCP server.  
Use the debugging dialercommand to enable DCC debugging.  
debugging dlsw  
Use the debugging dlswcommand to enable DLSw debugging.  
debugging dlsw ethernet-backup  
Use the debugging dlsw ethernet-backupcommand to enable debugging for DLSw Ethernet redundancy.  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
debugging dlsw filter  
Use the debugging dlsw filtercommand to enable debugging for DLSw filtering.  
debugging dlsw packet  
Use the debugging dlsw packetcommand to enable SSP packet debugging for DLSw.  
debugging dlsw reachable-cache  
Use the debugging dlsw reachable-cachecommand to enable DLSw reachability debugging.  
debugging dlsw udp  
debugging dns  
Use the debugging dlsw udpcommand to enable UDP packet debugging for DLSw.  
Use the debugging dnscommand to enable DNS client debugging.  
Use the debugging dvpncommand to enable DVPN debugging.  
debugging dvpn  
debugging encrypt-card  
Use the debugging encrypt-cardcommand to enable debugging on the specified or all encryption cards.  
 
3Com Router 5000/6000 Family  
Command Reference  
21  
debugging esis  
Use the debugging esis eventcommand to enable debugging for ES-IS protocol-related events. You can  
display event information using this command, such as changes of neighbor states, entries in Level 0  
routing table, and interface states.  
Use the debugging esis packetcommand to enable debugging for ES-IS packets. You display information  
about received/transmitted ES-IS packets, such as packet size, packet type, packet HT, and Layer 2 and  
Layer 3 address.  
User view  
User view  
User view  
User view  
User view  
debugging firewall  
debugging fr  
Use the debugging firewallcommand to enable the information debugging of the firewall packet filtering.  
Use the debugging frcommand to enable frame relay information debugging.  
debugging fr compress  
Use the debugging fr compresscommand to enable FRF9 IPHC debugging of frame relay.  
debugging fr compression  
Use the debugging fr compression iphccommand to enable FRF20 IPHC debugging of frame relay.  
debugging fr pvc-group  
Use the debugging fr pvc-groupcommand to enable debugging for the specified PVC group or all PVC  
groups.  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
debugging hdlc clns  
debugging hwatacs  
debugging hwping  
debugging igmp  
Use the debugging hdlc clnscommand to enable debugging for HDLC OSI packets.  
Use the debugging hwtacacscommand to enable TACACS+ debugging.  
Use the debugging hwpingcommand to enable HWPing debugging.  
Use the debugging igmpcommand to enable IGMP debugging functions.  
Use the debugging ikecommand to enable IKE debugging.  
Use the debugging ike dpdcommand to enable IKE DPD debugging.  
Use the debugging ip icmpcommand to enable the ICMP debugging.  
debugging ike  
debugging ike dpd  
debugging ip  
debugging ip count  
Use the debugging ip countcommand to enable debugging for the IP Accounting module (the IP  
Accounting).  
User view  
User view  
User view  
User view  
debugging ip multicast-policy  
Use the debugging ip multicast-policycommand to enable the debugging of IP multicast policy routing.  
debugging ip netstream  
Use the debugging ip netstreamcommand to enable NetStream debugging.  
debugging ip urpf  
Use the debugging ip urpfcommand to display the information on the rejected packets by URPF.  
 
22  
3Com Router 5000/6000 Family  
Command Reference  
debugging ipsec  
Use the debugging ipseccommand to turn IPSec debugging on.  
User view  
debugging ipx packet  
Use the debugging ipx packetcommand to enable IPX packet debugging switch to view the contents of  
IPX packet received and transmitted.  
User view  
User view  
User view  
User view  
User view  
User view  
debugging ipx ping  
debugging ipx rip  
Use the debugging ipx pingcommand to enable IPX Ping packet debugging switch to view the contents  
of Ping packet received and transmitted.  
Use the debugging ipx ripcommand to enable RIP debugging switch to view information on RIP packet  
received and transmitted, routing changes and timer expiry.  
debugging ipx rtpro-flash  
Use the debugging ipx rtpro-flashcommand to turn on the debugging switch of route refreshing in the  
IPXRM module.  
debugging ipx rtpro-interface  
Use the debugging ipx rtpro-interfacecommand to turn on the debugging switch of interface change  
in the IPXRM module.  
debugging ipx rtpro-routing  
Use the debugging ipx rtpro-routingcommand to turn on the debugging switch of route change in the  
IPXRM module.  
debugging ipx sap  
Use the debugging ipx sapcommand to enable IPX SAP debugging switch to view information on SAP  
packet received and transmitted, routing changes and timer expiry.  
User view  
User view  
User view  
debugging isdn  
debugging isis  
Use the debugging isdncommand to enable ISDN debugging.  
Use the debugging isiscommand to enable IS-IS debugging.  
debugging isis es-adjacency  
Use the debugging isis es-adjacencycommand to enable debugging for IS-IS protocol-related events  
occur on neighboring ESs.  
User view  
debugging isis is-adjacency  
Use the debugging isis is-adjacencycommand to enable debugging for IS-IS protocol-related events  
occur on neighboring ISs.  
User view  
User view  
User view  
User view  
debugging lapd  
Use the debugging lapbcommand to enable LAPB debugging.  
debugging llc2  
Use the debugging llc2command to enable the LLC2 debugging.  
Use the debugging llc2 packetcommand to enable U frame debugging for LLC2.  
debugging llc2 packet  
debugging local-server  
Use the debugging local-servercommand to enable debugging for the local RADIUS authentication  
server.  
User view  
 
3Com Router 5000/6000 Family  
Command Reference  
23  
debugging mobile-ip advertise  
Use the debugging mobile-ip advertisecommand to enable debugging for mobility agent  
advertisements.  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
debugging mobile-ip mobile-router  
Use the debugging mobile-ip mobile-routecommand to enable debugging for an MR.  
debugging mobile-ip node  
Use the debugging mobile-ip nodecommand to enable debugging for MIP packets and events.  
debugging modem  
Use the debugging modemcommand to enable Modem debugging.  
Use the debugging mpls l2vpncommand to view L2VPN link information.  
Use the debugging ldpcommand to enable debugging of LDP messages.  
Use the debugging mpls lspmcommand to enable various LSP debugging.  
Use the debugging msdpcommand to enable MSDP debugging functions.  
debugging mpls l2vpn  
debugging mpls ldp  
debugging mpls lspm  
debugging msdp  
debugging multicast forwarding  
Use the debugging multicast forwardingcommand to enable multicast packet forwarding debugging  
functions.  
User view  
User view  
debugging multicast kernel-routing  
Use the debugging multicast kernel-routingcommand to enable multicast kernel routing debugging  
functions.  
debugging multicast status-forwarding  
Use the debugging multicast status-forwardingcommand to enable multicast forwarding status  
debugging functions.  
User view  
User view  
User view  
User view  
User view  
debugging nat  
Use the debugging natcommand to enable the NAT debugging function.  
Use the debugging ntp-servicecommand to enable NTP service debugging.  
Use the debugging ospfcommand to enable OSPF debugging.  
Use the debugging padcommand to enable PAD debugging.  
debugging ntp-service  
debugging ospf  
debugging pad  
debugging physical  
Use the debugging physicalcommand to enable debugging of the physical module on the specified  
interface.  
User view  
User view  
User view  
debugging pim common  
debugging pim dm  
Use the debugging pim commoncommand to enable common PIM debugging functions.  
Use the debugging pim dmcommand to enable PIM-DM debugging functions.  
 
24  
3Com Router 5000/6000 Family  
Command Reference  
debugging pim sm  
debugging pki  
Use the debugging pim smcommand to enable PIM-SM debugging functions.  
Use the debugging pkicommand to enable PKI debugging functions.  
Use the debugging portal command to enable portal debugging.  
User view  
Any view  
User view  
debugging portal  
debugging pos  
Use the debugging pos eventcommand to enable event debugging for the POS access service.  
Use the debugging pos errorcommand to enable error debugging for the POS access service.  
Use the debugging pos packetcommand to enable packet debugging for the POS access service.  
Use the debugging pos allcommand to enable all debugging for the POS access service.  
User view  
User view  
debugging pos-app  
Use the debugging pos-appcommand to enable debugging for the specified or all POS applications.  
debugging pos-interface  
Use the debugging pos-interfacecommand to enable debugging for the specified or all POS access  
ports.  
User view  
debugging ppp { all | cbcp | ccp | scp }  
Use the debugging ppp { all | cbcp | ccp | scp }command to enable PPP related cbcp, ccp, scp or  
all debugging.  
User view  
User view  
debugging ppp { chap | pap }  
Use the debugging ppp { chap | pap }command to enable PPP related CHAP or PAP debugging.  
debugging ppp { core | ip | ipcp | lcp | lqc | mp }  
Use the debugging ppp { core | ip | ipcp | lcp | lqc | mp }command to enable PPP related core,  
ip, ipcp, lcp, lqc or mp debugging.  
User view  
User view  
debugging ppp compression iphc rtp  
Use the debugging ppp compression iphc rtpcommand to view debugging information about  
IP/UDP/RTP header compression in IP header compression.  
debugging ppp compression iphc tcp  
Use the debugging ppp compression iphc tcpcommand to view the single packet information of the  
IP/TCP header compression.  
User view  
User view  
User view  
User view  
User view  
User view  
debugging pppoe-client  
The command debugging pppoe-clientis used to enable PPPoE Client debugging switch.  
Use the debugging pppofrcommand to enable PPPoFR debugging.  
Use the debugging qllccommand to enable QLLC debugging.  
debugging pppofr  
debugging qllc  
debugging radius  
debugging rip  
Use the debugging radiuscommand to enable RADIUS debugging.  
Use the debugging ripcommand to enable RIP debugging.  
 
3Com Router 5000/6000 Family  
Command Reference  
25  
debugging rlogin  
Use the debugging rlogincommand to enable remote login (rlogin) debugging.  
User view  
User View  
User view  
User view  
debugging rsh  
Use the debugging rshcommand to enable RSH debugging.  
debugging sdlc  
debugging slip  
debugging snmp-agent  
Use the debugging sdlccommand to enable the SDLC debugging.  
Use the debugging slipcommand to enable the debugging switch of the SLIP protocol.  
Use the debugging snmp-agentcommand to enable SNMP agent debugging and specify the information  
to be output.  
User view  
User view  
User view  
User view  
debugging standby event  
Use the debugging standby eventcommand to enable debugging of the backup center.  
debugging stp  
Use the debugging stpcommand to enable STP debugging.  
debugging ssh client  
debugging ssh server  
Use the debugging ssh clientcommand to enable SSH client debugging.  
Use the debugging ssh servercommand to output information such as the negotiation process regulated  
by SSH1.5 protocol to information center as debugging formation and to debug a user interface separately.  
User view  
User view  
User view  
debugging tcp event  
debugging tcp md5  
debugging tcp packet  
Use the debugging tcp eventcommand to enable TCP events debugging.  
Use the debugging tcp md5command to enable the MD5 authentication debugging of the TCP connection.  
Use the debugging tcp packetcommand to enable the debugging of TCP connection. The number of  
debugging switches users can enable is limited, that is, at the same time only a fixed number of debugging  
switches can be enabled (combination of task ID and socket ID).  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
debugging telnet  
Use the debugging telnetcommand to enable Telnet connection debugging.  
Use the debugging tunnelcommand to enable tunnel debugging.  
debugging tunnel  
debugging tftp-server  
debugging udp-helper  
debugging udp packet  
debugging voice cm  
Use the debugging tftp-servercommand to enable TFTP server debugging.  
Use the debugging udp-helpercommand to enable UDP Helper debugging.  
Use the debugging udp packetcommand to enable the debugging of UDP connection.  
Use the debugging voice cmcommand to enable debugging for CM.  
 
26  
3Com Router 5000/6000 Family  
Command Reference  
debugging voice data-flow  
debugging voice dpl  
Use the debugging voice data-flowcommand to enable debugging for voice data processes.  
User view  
User view  
User view  
Use the debugging voice dplcommand to enable the debugging of voice dial program.  
debugging voice fax  
debugging voice h225  
Use the debugging voice faxcommand to enable fax debugging.  
Use the debugging voice h225command to enable debugging for the H.225.0 negotiation messages or  
events.  
User view  
debugging voice h245  
Use the debugging voice h245command to enable debugging for the H.245 negotiation messages or  
events.  
User view  
User view  
debugging voice ipp  
debugging voice r2  
Use the debugging voice ippcommand to enable H.323 recommendation suite module debugging.  
Use the debugging voice r2command to enable the corresponding debugging in R2 signaling module.  
Use the debugging voice r2 ccbcommand to view the information of the corresponding control block by  
specifying the E1 port number and time slot number.  
User view  
debugging voice ras  
debugging voice rcv  
Use the debugging voice rascommand to enable the debugging information output switch of RAS  
messages interacted between GK Client and GK Server.  
User view  
User view  
Use the debugging voice rcvcommand to enable the debugging of the RCV module.  
debugging voice rcv r2  
Use the debugging voice rcv r2command to enable the debugging between the RCV module and the  
R2 module of bottom layer.  
User view  
User view  
User view  
User view  
User view  
debugging voice sip  
Use the debugging voice sipcommand to enable SIP debugging.  
debugging voice sip rm  
Use the debugging voice sip rmcommand to enable debugging for RM module.  
debugging voice sip sm  
Use the debugging voice sip cmcommand to enable debugging for SM module.  
debugging voice vas  
Use the debugging voice vascommand to enable the VAS module debugging.  
debugging voice vas fax  
Use the debugging voice vas faxcommand to enable the debugging of fax data access between the VAS  
module and voice card.  
User view  
User view  
User view  
debugging voice vcc  
debugging voice vmib  
Use the debugging voice vcccommand to enable the debugging at various levels of the VCC module.  
Use the debugging voice vmibcommand to enable the voice MIB module debugging.  
 
3Com Router 5000/6000 Family  
Command Reference  
27  
debugging voice vofr  
Use the debugging voice vofrcommand to enable VoFR module debugging.  
User view  
User view  
debugging voice vpp  
Use the debugging voice vppcommand to enable the debugging of the VPP module.  
debugging voice vpp r2  
Use the debugging voice vpp r2command to enable the debugging between the VPP module and the  
R2 module of bottom layer.  
User view  
User view  
User view  
User view  
User view  
debugging vrrp  
debugging vty  
Use the debugging vrrpcommand to enable VRRP debugging.  
Use the debugging vtycommand to enable VTY debugging.  
debugging web java-blocking  
Use the debugging web java-blockingcommand to enable Java blocking debugging.  
debugging web url-filter host  
Use the debugging web url-filter hostcommand to enable the URL address filtering debugging.  
debugging web url-filter parameter  
Use the debugging web url-filter parametercommand to enable the URL parameter filtering  
debugging.  
User view  
User view  
debugging x25  
debugging x25 x2t  
debugging x25 xot  
default  
Use the debugging x25command to enable X.25 debugging.  
Use the debugging x25 x2tcommand to enable X2T debugging.  
Use the debugging x25 xotcommand to enable XOT debugging  
System view  
User view  
Use the defaultcommand to restore the default of all the R2 configurations and reset the R2 call statistics  
to 0.  
R2 CAS view  
OSPF view  
default cost  
default-cost  
Use the default costcommand to configure the default cost for OSPF to redistribute external routes.  
Use the default-costcommand to configure the cost of the default route transmitted by OSPF to the STUB  
or NSSA area.  
OSPF Area view  
RIP view  
default cost  
Use the default costcommand to configure the default routing cost of a redistributed route.  
default entity compression  
Use the default entity compressioncommand to globally configure the mode of coding and decoding  
as the default value.  
Voice Dial Program view  
default entity fax  
Use the default entity faxcommand to set the default fax parameter settings globally.  
Voice Dial Program view  
 
28  
3Com Router 5000/6000 Family  
Command Reference  
default entity modem compatible-param  
Use the default entity modem compatible-paramcommand in the case that you fail to use standard  
Modem PCM to interoperate with devices from other vendors.  
Voice Dial Program view  
default entity modem protocol  
Use the default entity modem protocolnonecommand to globally disable Modem function of voice  
entity.  
Use the default entity modem protocolpcmcommand to globally configure PCM Modem protocol type  
of voice entity, including coding/decoding and Modem negotiation mode.  
Voice Dial Program view  
default entity normal-connect slow-h245  
Use the default entity normal-connect slow-h245command to globally disable the calling end from  
actively initiating an H245 connection request to the called end before the called end is hooked off.  
Use the default entity normal-connect slow-h245command to default to globally disable the calling  
end from actively initiating the H245 connection request to the called end before the called end is hooked  
off. In this case, all newly created voice entities and voice entities which have not been configured with this  
function will inherit this configuration.  
Voice Dial Program view  
default entity payload-size  
Use the default entity payload-sizecommand to configure the default time length of voice packets with  
different coding formats.  
Voice Dial Program view  
default entity service data  
Use the default entity service datacommand to globally configure enabling data call service.  
Voice dial program view  
default entity vad-on  
default interval  
default limit  
Use the default entity vad-oncommand to globally configure enabling silence detection as the default  
value.  
Voice Dial Program view  
Use the default intervalcommand to configure the default interval for OSPF to redistribute external  
routes.  
OSPF view  
OSPF view  
Use the default limitcommand to configure default value of maximum number of redistributed routes.  
default local-preference  
Use the default local-preferencecommand to configure the local preference.  
BGP Unicast view  
BGP Multicast view  
VPNv4 view  
default med  
Use the default medcommand to configure the system MED value.  
BGP Unicast view  
BGP Multicast view  
VPNv4 view  
VPN Instance view  
default-route-advertise  
Use the default-route-advertisecommand to configure the default route of Level-1 and Level-2 routers.  
IS-IS view  
default-route-advertise  
Use the default-route-advertisecommand to make the system generate a default route to OSPF area.  
Use the default-route-advertisecommand at ABR to generate a default route which is advertised via  
the Type-5 LSA or Type-7 LSA no matter whether there is a default route in the routing table.  
OSPF view  
BGP view  
default-route imported  
Use the default-route importedcommand to redistribute local default routes into BGP.  
 
3Com Router 5000/6000 Family  
Command Reference  
29  
default tag  
Use the default tagcommand to configure the default tag of OSPF when it redistributes an external route.  
OSPF view  
OSPF view  
default type  
Use the default typecommand to configure the default type when OSPF redistributes external routes.  
delay  
Use the delaycommand to configure the related time parameters at the digital E&M subscriber-line (E1  
controller).  
Digital E&M Voice Subscriber-Line view  
delay  
Use the delaycommand to configure the relevant time parameters on an FXO or analog E&M  
subscriber-line.  
FXO Voice Subscriber-Line view  
delay-reversal  
Use the delay-reversalcommand to configure the timer's interval of polarity-reverse transmission delay  
on FXS interfaces.  
Voice Subscriber-Line view  
delete  
delete  
Use the deletecommand to delete the specified file.  
FTP Client view  
SFTP Client view  
Use the deletecommand to delete the specified file from the server as you would with the remove  
command.  
delete  
Use the deletecommand to move the specified file from the storage device to the recycle bin, where you  
can completely delete the file with the undeletecommand or restore it with the reset recycle-bin  
filenamecommand.  
User view  
System view  
System view  
delete rpf-route-static all  
Use the delete rpf-route-static allcommand to delete all the static multicast routes.  
delete static-routes all  
Use the delete static-routes allcommand to cancel all the static routes.  
description  
Use the descriptioncommand to configure port description. Identifying a port is the only function of this  
command.  
Ethernet Port view  
description  
description  
description  
Use the descriptioncommand to briefly describe a test operation.  
HWPing Test Group view  
Interface view  
Use the descriptioncommand to describe the interface.  
Use the descriptioncommand to configure description information for a specified VPN instance.  
Vpn-Instance view  
description (in Voice Entity View)  
Use the descriptioncommand to configure a voice entity description string.  
Voice Entity view  
description (in Voice Subscriber-Line View)  
Use the descriptioncommand to configure a subscriber-line description character string.  
FXO Voice Subscriber-Line view  
destination  
Use the destinationcommand to specify the destination IP address to be filled in the added IP header at  
the time of tunnel interface encapsulation.  
Tunnel Interface view  
 
30  
3Com Router 5000/6000 Family  
Command Reference  
destination-ip  
destination-port  
detect  
Use the destination-ipcommand to configure the destination IP address in the test.  
Use the destination-portcommand to configure the destination port in the test.  
Use the detectcommand to specify ASPF policy for application layer protocols.  
HWPing Test Group view  
HWPing Test Group view  
ASPF Policy view  
detect  
Use the detectcommand to enable data carrier detection as well as level detection on a serial interface.  
Asynchronous Serial Interface view  
Synchronous Serial Interface view,  
detect-ais (CE1/PRI Interface)  
Use the detect-aiscommand to enable alarm indication signal (AIS) detect on the CE1/PRI interface.  
CE1/PRI Interface view  
System view  
detect group  
Use the detect-groupcommand to create a detect group and enter its view.  
detect list  
Use the detect-listcommand to add an IP address to the detect group and assign the address a detecting  
sequence number.  
Detect Group view  
IKE Proposal view  
dh  
Use the dhcommand to select the Diffie-Hellman group for an IKE proposal.  
dhcp accounting domain (Interface view)  
Use the dhcp server accounting domaincommand to enable DHCP accounting for addresses from the  
interface address pool and configure a domain for DHCP accounting.  
Interface view  
System view  
dhcp enable  
Use the dhcp enablecommand to enable DHCP.  
dhcp relay information  
Use the dhcp relay information enablecommand to enable the DHCP relay to support option 82  
globally.  
System view  
System view  
dhcp relay information strategy  
Use the dhcp relay information strategycommand to configure a strategy for handling packets with  
option 82 on the DHCP relay.  
dhcp relay release  
Use the dhcp relay releasecommand to send an IP address releasing request to a DHCP server via the  
DHCP relay.  
Interface view  
System view  
dchp select (Interface view)  
Use the dhcp selectcommand in Interface view to select a method for disposing the DHCP packets  
destined to the local device.  
Interface view  
System view  
System view  
dchp select (System view)  
Use the dhcp selectcommand in System view to select a method for multiple interfaces in a specified  
range to dispose the DHCP packets destined to the local device.  
dhcp server accounting domain interface (System view)  
Use the dhcp server accounting domain interfacecommand to enable DHCP accounting for addresses  
from the address pools of the specified interfaces and configure a domain for DHCP accounting.  
 
3Com Router 5000/6000 Family  
Command Reference  
31  
dhcp server bims-server (Interface view)  
Use the dhcp server bims-servercommand to enable and configure BIMS option support on the current  
interface.  
Ethernet Interface (or Subinterface) view  
dhcp server bims-server interface (System view)  
Use the dhcp server bims-server interfacecommand to enable and configure BIMS option support for  
an interface or all interfaces configured with interface address pools.  
System view  
System view  
dhcp server detect  
Use the dhcp server detectcommand to enable pseudo-DHCP-server detection.  
dhcp server dns-list  
Use the dhcp server dns-listcommand in interface view to configure DNS IP addresses for an interface  
configured with a DHCP address pool.  
Ethernet Interface (or Subinterface) view  
dhcp server dns-list interface (System view)  
Use the dhcp server dns-list interfacecommand to assign DNS IP addresses to the DHCP address  
pool of multiple interfaces in a specified range.  
System view  
dhcp server domain-name (Interface view)  
Use the dhcp server domain-namecommand in interface view to configure the domain name that the  
DHCP address pool of the current interface allocates to clients.  
Ethernet Interface (or Subinterface) view  
dhcp server domain-name interface (System view)  
Use the dhcp server domain-name interfacecommand in system view to configure the domain name  
that the DHCP address pool of the interfaces in a specified range allocates to DHCP clients.  
System view  
dhcp server expired (Interface view)  
Use the dhcp server expiredcommand in interface view to configure a valid period allowed for leasing IP  
addresses in the current interface DHCP address pool.  
Ethernet Interface (or Subinterface) view  
dhcp server forbidden-ip  
Use the dhcp server forbidden-ipcommand to exclude IP addresses in a specified range to participate  
in the auto-allocation.  
System view  
System view  
dhcp server interface (System view)  
Use the dhcp server expired interfacecommand in system view to configure a valid period allowed for  
leasing IP addresses in the interface DHCP address pool of the interfaces in a specified range.  
dhcp server ip-pool  
Use the dhcp server ip-poolcommand to create a DHCP address pool and access the DHCP address  
pool view.  
System view  
dhcp server nbns-list (Interface view)  
Use the dhcp server nbns-listcommand in interface view to configure NetBIOS server addresses in the  
DHCP address pool of current interface.  
Ethernet Interface (or Subinterface) view  
dhcp server nbns-list interface (System view)  
Use the dhcp server nbns-list interfacecommand in system view to configure NetBIOS server  
addresses for the clients that get ip address from the DHCP address pool of the interfaces in a specified  
range.  
System view  
dhcp server netbios-type (Interface view)  
Use the dhcp server netbios-typecommand in interface view to configure the NetBIOS node type of the  
DHCP clients of the current interface.  
Ethernet Interface (or Subinterface) view  
dhcp server netbios-type interface (System view)  
Use the dhcp server netbios-type interfacecommand in system view to configure a NetBIOS node  
type for the DHCP clients of the interfaces in a specified range.  
System view  
 
32  
3Com Router 5000/6000 Family  
Command Reference  
dhcp server option (Interface view)  
Use the dhcp server optioncommand in interface view to configure a DHCP self-defined option for the  
DHCP address pool of the current interface.  
Ethernet Interface (or Subinterface) view  
dhcp server option interface (System view)  
Use the dhcp server optioncommand in system view to configure a DHCP self-defined option for the  
interfaces in a specified range.  
System view  
dhcp server ping  
Use the dhcp server pingcommand to configure the maximum number of ping packets that the DHCP  
server is allowed to send and the longest time period that the DHCP server should wait for the response to  
each ping packet.  
System view  
System view  
dhcp server relay information enable  
Use the dhcp server relay information enablecommand to enable the DHCP server to support option  
82.  
dhcp server static-bind  
Use the dhcp server static-bindcommand to configure a static address binding in the DHCP address  
pool of the current interface.  
Ethernet Interface (or Subinterface) view  
Interface view  
dhcp server synchronize arp (Interface view)  
Use the dhcp server synchronize arpcommand to enable authorized ARP for a DHCP interface address  
pool.  
dhcp server synchronize arp interface (System view)  
Use the dhcp server synchronize arp interfacecommand to enable authorized ARP for specified  
DHCP interface address pools.  
System view  
dhcp server voice-config (Interface view)  
Use the dhcp server voice-configcommand to enable the DHCP server to send option 184 and  
suboptions of 184 when it assigns addresses from the current interface address pool.  
Interface view  
dhcp server voice-config interface (System view)  
Use the dhcp server voice-config interfacecommand to enable the DHCP server to send option 184  
and suboptions of 184 when it assigns addresses from the specified interface address pool.  
System view  
Voice Entity view  
Voice view  
dial-prefix  
Use the dial-prefixcommand to configure the prefix of the telephone number dialed by the voice entity.  
Use the dial-programcommand to enter the voice dial program view.  
dial-program  
dialer bundle  
dialer bundle-member  
Use the dialer bundlecommand to configure a dialer bundle used by a dialer interface.  
Dialer Interface view  
Use the dialer bundle-membercommand to configure a physical interface included in a dialer bundle in  
the Resource-Shared DCC application.  
Physical Interface view  
Physical or Dialer Interface view  
Physical or Dialer Interface view  
dialer call-in  
Use the dialer call-incommand to enable ISDN callback according to ISDN caller ID.  
dialer callback-center  
Use the dialer callback-centercommand to enable the callback server function.  
dialer circular-group  
Use the dialer circular-groupcommand to add the physical interface to a dialer circular group specified  
here.  
Physical Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
33  
dialer disconnect  
Use the dialer disconnectcommand to clear the dial-up link or the session link on the specified interface  
at the PPPoE/PPPoA client.  
Any view  
dialer enable-circular  
Use the dialer enable-circularcommand to enable Circular DCC.  
Physical or Dialer Interface view  
dialer group  
Use the dialer-groupcommand to configure access control on the packets transmitted on a DCC interface  
and to place the interface in an access control group.  
Physical or Dialer Interface view  
dialer isdn-leased  
dialer isdn-leased  
Use the dialer isdn-leasedcommand to configure an ISDN B channel (can be either the channel on a  
BRI or PRI interface) to be the leased line.  
Physical or Dialer Interface view  
Use the dialer isdn-leased 128kcommand to configure 128K leased line connection.  
Use the dialer isdn-leasednumbercommand to configure 64K leased line connection.  
ISDN BRI Interface view  
dialer number  
Use the dialer numbercommand to configure a dial number for placing a call to a single remote end.  
Physical or Dialer Interface view  
dialer priority  
Use the dialer prioritycommand to configure a priority for a physical interface in a dialer circular group  
in the Circular DCC configuration.  
Physical Interface view  
dialer queue-length  
Use the dialer queue-lengthcommand to configure the number of packets which comply with the "permit"  
statement that can be buffered before a link is set up.  
Physical or Dialer Interface view  
dialer route  
Use the dialer routecommand to allow a DCC interface to call the specified destination address (host or  
network address) or to receive calls from multiple remote ends.  
Physical or Dialer Interface view  
dialer-rule  
Use the dialer-rulecommand to configure the conditions of the data packet that can trigger a DCC call.  
System view  
dialer threshold  
Use the dialer thresholdcommand to configure the traffic threshold of a link on the DCC interface so that  
another link can be enabled to call the same destination address when the ratio of traffic on all connected  
links on the DCC interface to the available bandwidth exceeds the preset percentage.  
Dialer Interface view  
dialer timer autodial  
Use the dialer timer autodialcommand to configure the automatic dialing interval of DCC.  
Physical or Dialer Interface view  
dialer timer compete  
Use the dialer timer competecommand to configure an idle interval for an interface after call contention  
occurs on the interface.  
Physical or Dialer Interface view  
dialer timer enable  
Use the dialer timer enablecommand to configure an interval for the next call attempt on an interface  
after the link is disconnected.  
Physical or Dialer Interface view  
dialer timer idle  
Use the dialer timer idlecommand to configure the interval that a link is allowed to be idle (in other  
words, the interval when there is no packets which comply with the “permit” statements transmitted) after a  
call has been set up on the interface.  
Physical or Dialer Interface view  
 
34  
3Com Router 5000/6000 Family  
Command Reference  
dialer timer wait-carrier  
Use the dialer timer wait-carriercommand to configure the timeout time of wait-carrier timer.  
Physical or Dialer Interface view  
dialer timer warmup  
Use the dialer timer warmupcommand to set the length of the warmup timer on the router configured with  
the dial-up backup function. It is the time that the router must wait for bringing the dial-up backup function  
into effect after a reboot.  
System view  
dialer user  
Use the dialer usercommand to configure remote user name for authenticating requests when calls are  
received.  
Dialer Interface view  
differential-delay  
Use the differential-delaycommand to set the maximum differential delay for the member links in the  
IMA group.  
IMA Group Interface view  
dir  
dir  
dir  
Use the dircommand to query for a specified file.  
FTP Client view  
Use the dircommand to view the files in the specified directory as you would with the lscommand.  
SFTP Client view  
Use the dircommand, you can view information about the specified file or directory in the router storage  
device.  
User view  
direct listen-port  
disconnect  
Use the direct listen-port Xcommand to set the listening port for vty.  
Vty User Interface view  
FTP Client view  
Any view  
Use the disconnectcommand to disconnect from the remote FTP server but remain in FTP client view.  
Use the display l2tp sessioncommand to view the current L2TP sessions.  
display l2tp session  
display l2tp tunnel  
display l2tp user  
Use the display l2tp tunnelcommand to view information of the current L2TP tunnels.  
Use the display l2tp usercommand to view information about the current L2TP users.  
Any view  
Any view  
display aaa unsent-h323-call-record  
Use the display aaa unsent-h323-call-recordcommand to view the detail record information about the  
calls failed to be sent.  
Any view  
Any view  
Any view  
Any view  
Any view  
display acl  
Use the display aclcommand to view the rules of access control list.  
Use the display alarm urgentcommand to view the stored alarms in a specified way.  
Use the display arpcommand to view the ARP mapping table.  
display alarm urgent  
display arp  
display arp timer aging  
Use the display arp timer agingcommand to display the aging timer for dynamic ARP entries.  
 
3Com Router 5000/6000 Family  
Command Reference  
35  
display aspf all  
Use the display aspf allcommand to view the information of all ASPF policies and sessions.  
Any view  
Any view  
Any view  
Any view  
display aspf interface  
Use the display aspf interfacecommand to view the interface configuration of the inspection policy.  
display aspf policy  
display aspf session  
display atm class  
Use the display aspf policycommand to view the configuration of a specific inspection policy.  
Use the display aspf sessioncommand to view the information of the ASPF sessions.  
Use the display atm classcommand to view the information about ATM-Class. By default, if no  
ATM-Class name is specified, the information of all ATM-Class is displayed.  
Any view  
Any view  
Any view  
display atm interface  
display atm map-info  
display atm map-info  
Use the display atm map-infocommand to view the information about the upper layer protocol mapping  
table of ATM.  
Use the display atm map-infocommand to display upper layer protocol map information about a specified  
ATM interface.  
Use the display atm map-infocommand to view the information about the upper layer protocol mapping  
table of ATM.  
Any view  
Any view  
Any view  
Any view  
display atm pvc-group  
display atm pvc-info  
display auto-config  
display bgp l2vpn  
Use the display atm pvc-groupcommand to view the information about PVC-Group.  
Use the display atm pvc-infocommand to view the information about PVC.  
Use the display auto-configcommand to view the status of auto-config.  
Use the display bgp l2vpn allcommand to view system operating information and all L2VPN  
information.  
Any view  
Any view  
Any view  
Any view  
Any view  
display bgp group  
Use the display bgp groupcommand to view the information of peer groups.  
display bgp multicast group  
Use the display bgp multicast groupcommand to view the information about peer groups.  
display bgp multicast network  
Use the display bgp multicast networkcommand to view the routing information that MBGP advertises.  
display bgp multicast peer  
Use the display bgp multicast peercommand to view information about MBGP peers.  
display bgp multicast routing  
Use the display bgp multicast routingcommand to view the MBGP routing information whose IP  
address is specified in the BGP routing table.  
Any view  
 
36  
3Com Router 5000/6000 Family  
Command Reference  
display bgp multicast routing as-path-acl  
Use the display bgp multicast routing as-path-aclcommand to view in the BGP routing table the  
MBGP routes that match the specified AS path list.  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
display bgp multicast routing cidr  
Use the display bgp multicast routing cidrcommand to view the routing information with non-natural  
network mask (that is, classless inter-domain routing, CIDR).  
display bgp multicast routing community-list  
Use the display bgp multicast routing community-listcommand to view the routing information that  
is permitted by the MBGP community list.  
display bgp multicast routing community  
Use the display bgp multicast routing communitycommand to view the routing information that  
belongs to the specified MBGP community.  
display bgp multicast routing different-origin-as  
Use the display bgp multicast routing different-origin-ascommand to view AS routes with  
different origins.  
display bgp multicast routing peer  
Use the display multicast routing peercommand to view the route received from or sent to the  
specified multicast neighbor.  
display bgp multicast routing regular-expression  
Use the display bgp multicast routing regular-expression command to view the routing information  
matching the specified AS regular expression.  
display bgp multicast routing statistic  
Use the display bgp multicast routing statisticcommand to view statistics of MBGP route  
information.  
Any view  
Any view  
Any view  
display bgp network  
display bgp paths  
display bgp peer  
Use the display bgp networkcommand to view the routing information that has been configured.  
Use the display bgp pathscommand to view the information about AS paths  
Use the display bgp peercommand to view the information of peer.  
Use the display bgp multicast peer command to view the information of MBGP peer.  
Use the display bgp vpnv4 peercommand to view the information of VPN peer.  
Any view  
display bgp routing  
Use the display bgp routingcommand to view the BGP routing information in the BGP routing table.  
Use the display bgp multicast routingcommand to view the MBGP routing information in the BGP  
routing table.  
Use the display bgp vpnv4 routingcommand to view the VPN routing information in the BGP routing  
table.  
Any view  
Any view  
display bgp routing as-path-acl  
Use the display bgp routing as-path-aclcommand to view routes that match an as-path ACL.  
display bgp routing cidr  
Use the display bgp routing cidrcommand to view the routing information about the non-natural mask  
(namely the classless inter-domain routing, CIDR).  
Any view  
 
3Com Router 5000/6000 Family  
Command Reference  
37  
display bgp routing community  
Use the display bgp routing communitycommand to view the routing information related to the specified  
BGP community number in the routing table.  
Any view  
display bgp routing community-list  
Use the display bgp routing community-listcommand to view the routing information matching the  
specified BGP community list.  
Any view  
Any view  
display bgp routing dampened  
Use the display bgp routing dampenedcommand to view BGP dampened routes.  
display bgp routing different-origin-as  
Use the display bgp routing different-origin-ascommand to view routes that have different source  
autonomous systems.  
Any view  
display bgp routing flap-info  
Use the display bgp routing flap-infocommand to view BGP flap statistics. When  
<network-address mask> is <0.0.0.0 0.0.0.0>, this command will view the flap statistics of all BGP  
routes.  
Any view  
Any view  
Any view  
Any view  
Any view  
display bgp routing label  
Use the display bgp routing labelcommand to view routing information and label information in the  
BGP routing table.  
display bgp routing peer { advertised | received }  
Use the display bgp routing peercommand to view the routing information the specified BGP peer  
advertised or received.  
display bgp routing peer dampened  
Use the display bgp routing peer dampenedcommand to view the information about the dampened  
routes received from the specified peer.  
display bgp routing peer regular-expression  
Use the display bgp routing peer regular-expression command to view the route information  
received from the specified peer and matching the specified regular expression.  
display bgp routing regular-expression  
Use the display bgp routing regular-expression command to view the routing information matching  
the specified AS regular expression.  
Any view  
Any view  
Any view  
display bgp routing statistic  
Use the display bgp routing statisticcommand to display statistics about BGP routes.  
Use the display bgp vpnv4command to view VPNv4 information in BGP database.  
display bgp vpnv4  
display bootp client  
Use the display bootp clientcommand to display information about the BOOTP client, such as MAC  
address and IP address.  
Any view  
Any view  
Any view  
display bridge address-table  
Use the display bridge address-tablecommand to view the information of MAC address forwarding  
table.  
display bridge information  
Use the display bridge informationcommand to view the information of one or all the enabled bridge  
sets in bridge module.  
 
38  
3Com Router 5000/6000 Family  
Command Reference  
display bridge spanning tree  
Use the display bridge spanning-treecommand to view STP state and statistics for traffic analysis and  
control.  
Any view  
Any view  
display bridge traffic  
Use the display bridge trafficcommand to view the traffic statistics on an interface.  
display brief interface  
Use the display brief interfacecommand to display summary information about the specified or all  
interfaces.  
Any view  
Any view  
Any view  
Any view  
Any view  
display ccc  
Use the display ccccommand to view CCC connection information.  
Use the display channelcommand to view the contents in an information channel.  
Use the display clipboardcommand to view the contents of the clipboard.  
Use the display clnscommand to display current CLNS information.  
display channel  
display clipboard  
display clns  
display clns interface  
Use the display clns interfacecommand to display CLNS related information about a specified  
interface.  
Any view  
display clns routing-table  
Use the display clns routing-tablecommand to display all active CLNS routes, including those in Level  
0, Level 1, and Level 2 routing tables.  
Any view  
Any view  
Any view  
Any view  
display clns statistics  
Use the display clns statisticcommand to display statistics information about CLNS flow.  
Use the display clockcommand to display the current system time and date.  
display clock  
display command-alias  
Use the display command-aliascommand to view the current command alias settings.  
display configure-user  
Use the display configure-usercommand to view information about the user who is currently authorized  
to configure the equipment.  
Any view  
display connection  
Use the display connectioncommand to view the relevant information on the specified user connection  
or all the connections. The output can help you troubleshoot user connections.  
Any view  
Any view  
Any view  
display connection-limit policy  
Use the display connection-limit policycommand to display connection limit policy.  
display connection-limit statistics  
Use the display connection-limit statisticscommand to display the connection limit statistics.  
display controller cpos  
Use the display controller cposcommand to view information about CPOS interfaces, such as state of  
the E1/T1 channels and alarms, and errors that occur to regeneration section, multiplex section, and  
higher-order path.  
Any view  
 
3Com Router 5000/6000 Family  
Command Reference  
39  
display controller cpos e1  
Use the display controller cpos e1command to view the physical layer configuration information of a  
specified E1 channel on the specified CPOS interface.  
Any view  
display controller cpos t1  
Use the display controller cpos t1command to view the physical layer configuration information of a  
specified T1 channel on the specified CPOS interface.  
Any view  
Any view  
Any view  
display controller e1  
display controller e3  
display controller t1  
Use the display controller e1command to display the information related to a CE1/PRI interface.  
Use the display controller e3command to view state information on a CE3 interface.  
Use the display controller t1command to display the information about the specified CT1/PRI  
interface.  
Any view  
Any view  
Any view  
display controller t3  
display cpu-usage  
Use the display controller t3command to view state about a CT3 interface.  
Use the display cpu-usagecommand to view statistics about CPU usage.  
display cpu-usage history  
Use the display cpu-usage historycommand to view in graphics the CPU usage statistic history of the  
entire system, the specified task, or the interface board in the specified slot.  
Any view  
Any view  
Any view  
display current-configuration  
Use the display current-configurationcommand to view the running configurations on the router.  
Use the display debuggingcommand to view the enabled debugging switches.  
display debugging  
display debugging ospf  
Use the display debugging ospfcommand to view the state of the debug switches for each OSPF  
process.  
Any view  
Any view  
display detect group  
Use the display detect-groupcommand to display configuration information about a specified detect  
group or all detect groups.  
display device  
Use the display devicecommand to view information on the hardware configurations of the system,  
including in-position state of the RPU, NPU, interface cards, power module, and fan module, the operating  
state of the interface cards, power module, and fan module, as well as the offline state of RPU and NPU.  
Any view  
display dhcp client  
Use the display dhcp clientcommand to display the statistic information of the DHCP client. Executing  
the command attached without the keyword parameter verbose will display only the brief address allocation  
information on the DHCP client.  
Any view  
Any view  
Any view  
display dhcp relay address  
Use the display dhcp relay addresscommand to view the DHCP relay address configuration of an  
interface.  
display dhcprelay-security  
Use the display dhcprelay-securitycommand to display the IP-to-MAC mappings of the clients  
obtaining IP addresses dynamically through the DHCP relay.  
 
40  
3Com Router 5000/6000 Family  
Command Reference  
display dhcp relay statistics  
Use the display dhcp relay statisticscommand to view the statistics of DHCP relay in packet errors,  
DHCP packets received from clients, DHCP packets received from and sent to servers, and DHCP packets  
sent to clients (including unicast and broadcast packets).  
Any view  
Any view  
Any view  
Any view  
Any view  
display dhcp server conflict  
Use the display dhcp server conflictcommand to view the DHCP address conflict statistics, including  
the information in conflicted IP address, conflict detection type, and conflict time.  
display dhcp server expired  
Use the display dhcp server expiredcommand to view the expired address leases in a DHCP address  
pool. In certain conditions, the addresses of the expired leases will be allocated to other DHCP clients.  
display dhcp server free-ip  
Use the display dhcp server free-ipcommand to view the free address ranges in DHCP address pools,  
that is, information about IP addresses that have not been allocated yet.  
display dhcp server ip-in-use  
Use the display dhcp server ip-in-usecommand to view the address binding information of DHCP  
clients, such as the information in hardware address, IP address, and address lease expiration.  
display dhcp server statistics  
Use the display dhcp server statisticscommand to view the statistics on the DHCP server, including  
such information as number of DHCP address pools, automatically or manually bound address and expired  
addresses, number of unknown packets, number of DHCP request packets, and number of response  
packets.  
Any view  
Any view  
display dhcp server tree  
Use the display dhcp server treecommand to view the tree-structure information of DHCP address  
pools, including the address pool at each node, option, address lease period, and DNS server information.  
display diagnostic-information  
Use the display diagnostic-informationcommand to view the operating information about the active  
modules in the system.  
Any view  
Any view  
Any view  
Any view  
display dialer  
Use the display dialercommand to view information on DCC interfaces.  
display dlsw bridge-entry  
Use the display dlsw bridge-entrycommand to view the bridge-set information.  
display dlsw circuits  
Use the display dlsw circuitscommand to view the DLSw virtual circuits.  
display dlsw ethernet-backup map  
Use the display dlsw ethernet-backup mapcommand to display information about address translation  
after you configure the Ethernet switch support feature.  
Any view  
Any view  
display dlsw ethernet-backup neighbour  
Use the display dlsw ethernet-backup neighbourcommand to display all neighbors of the current  
router.  
display dlsw information  
Use the display dlsw informationcommand to view the DLSw exchange capability information. The  
output information of the command facilitates the user to understand the status of the DLSw virtual circuit  
and perform fault diagnosis.  
Any view  
Any view  
display dlsw information  
Use the display dlsw informationcommand to display DLSw capability exchange information. The  
output of this command can help you understand the status of DLSw virtual circuits.  
 
3Com Router 5000/6000 Family  
Command Reference  
41  
display dlsw reachable-cache  
Use the display dlsw reachable-cachecommand to view the reachable-cache of DLSw.  
Any view  
Any view  
Any view  
Any view  
display dlsw remote  
display dlsw remote  
display dns domain  
Use the display dlsw remotecommand to view the information of the remote peers.  
Use the display dlsw remotecommand to display information about the specified or all remote peers.  
Use the display dns domaincommand to view the DNS domain names that are manually configured.  
display dns dynamic host  
Use the display dns dynamic-hostcommand to view the current contents in the domain name cache of  
the DNS client.  
Any view  
Any view  
display dns server  
display domain  
Use the display dns servercommand to view the DNS server addresses manually configured.  
Use the display domaincommand to view the configuration of a specified ISP domain or display the  
summary information of all ISP domains.  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
display dsl configuration  
Use the display dsl configurationcommand to view the actual ADSL configurations.  
display dsl configuration  
Use the display dsl configurationcommand to view the actual DSL configurations.  
display dsl status  
display dsl status  
display dsl version  
display dsl version  
display dvpn info  
Use the display dsl statuscommand to view the DSL state information.  
Use the display dsl statuscommand to view state about the specified DSL interface.  
Use the display dsl versioncommand to view DSL version and the available capabilities.  
Use the display dsl versioncommand to view the DSL version and the available functionality.  
Use the display dvpn infocommand to display the configuration and operating information about a  
specified DVPN.  
Any view  
Any view  
display dvpn ipsec-sa  
Use the display dvpn ipsec-sacommand to display the specified IPSec SA information.  
display dvpn map  
Use the display dvpn mapcommand to display information about maps in a DVPN domain, such as private  
IP address, public IP address, port number, DVPN connection state, DVPN connection type, and control ID.  
Any view  
Any view  
Any view  
display dvpn online-user  
Use the display dvpn online-usercommand to display the information about online DVPN users.  
display dvpn session  
Use the display dvpn sessioncommand to display information about sessions the device owns.  
 
42  
3Com Router 5000/6000 Family  
Command Reference  
display encrypt-card fast-switch  
Use the display encrypt-card fast-switchcommand to view the entries in the fast forwarding cache for  
the encryption cards.  
Any view  
Any view  
display encrypt-card sa  
Use the display encrypt-card sacommand to view SA information.  
display encrypt-card statistics  
Use the display encrypt-card statisticscommand to view statistics on the specified or all encryption  
cards.  
Any view  
Any view  
display encrypt-card syslog  
Use the display encrypt-card syslogcommand to view the current system log on the encryption cards.  
display environment  
Use the display environmentcommand to view the current values and the thresholds of the hardware  
system environment.  
Any view  
Any view  
Any view  
display esis  
Use the display esiscommand to display current ES-IS protocol state, such as the configuration timer  
(CT) to send ISH packets, the holding time (HT) of the information ISH packets carry.  
display esis interface  
Use the display esis interfacecommand to display ES-IS related information about a specified  
interface.  
display esis peer  
Use the display esis peercommand to display information about the neighbors dynamically discovered  
by ES-IS protocol (including dynamic ES and IS neighbors).  
Any view  
Any view  
display esis statistics  
Use the display esis statisticcommand to display statistics information about ES-IS flow.  
display fcm  
Use the display fcmcommand to display the count of dial-up negotiation failures and the count of  
disconnections upon transaction timeouts for FCM module interfaces.  
Any view  
display fe1 serial  
Use the display fe1 serialcommand to view the configuration and state about the specified or all E1-F  
interfaces.  
Any view  
Any view  
Any view  
display fib  
Use the display fibcommand to view the summary of the Forwarding Information Base.  
Use the display fib aclcommand to filter and display FIB information.  
display fib acl  
display fib begin  
Use the display fibcommand to output the lines related to the line containing the character string text in  
the buffer according to the regular expression.  
Use the display fib | begintext command to view the lines beginning from the line containing the  
character string text to the end line of the buffer.  
Use the display fib | includetext command to just view the lines containing the character string text.  
Use the display fib | excludetext command to view the lines not containing the character string text.  
Any view  
Any view  
display fib ip-prefix  
Use the display fib ip-prefixcommand to filter and display FIB information by prefix-list name in certain  
format.  
 
3Com Router 5000/6000 Family  
Command Reference  
43  
display fib longer  
Use the display fib longercommand to display the FIB table entries matching the destination address.  
Different parameters selected leads to different matching methods.  
Use the display fibcommand to display the FIB table entries whose destination address ranges from  
dest-addr1 dest-mask1 to dest-addr2 dest-mask2, including the FIB entries exactly matching dest-addr1  
dest-mask1 and dest-addr2 dest-mask2.  
Any view  
Any view  
display fib statistics  
Use the display fib statisticscommand to display the total numbers of FIB table entries.  
display firewall ethernet-frame-filter  
Use the display firewall ethernet-frame-filtercommand to view the filtering statistics by ACL on the  
interface, namely, the detailed filtering information based on the ACL configured via the firewall  
ethernet-frame-filter { acl-number| acl-name} { inbound | outbound } command.  
Any view  
Any view  
display firewall-statistics  
Use the display firewall-statistics command to view the firewall statistics.  
display fr class-map  
Use the display fr class-mapcommand to view information on frame relay class to interface map,  
including DLCIs of interfaces, subinterfaces on the interfaces and their DLCIs.  
Any view  
Any view  
Any view  
display fr compress  
display fr del  
Use the display fr compresscommand to view the statistics information of the frame relay compression.  
Use the display fr delcommand to view the contents in the specified or all DE rule lists.  
display fr dlci-switch  
Use the display fr dlci-switchcommand to view the information of the configured FR switching to check  
if the frame relay switching of a user is correctly configured.  
Any view  
Any view  
display fr fragment-info  
Use the display fr fragment-infocommand to view the frame relay fragment information.  
display fr inarp-info  
Use the display fr inarp-infocommand to view statistics about frame relay inverse ARP (INARP)  
packets, including requests and replies.  
Any view  
Any view  
Any view  
Any view  
Any view  
display fr interface  
display fr lmi-info  
display fr map-info  
display fr map-info  
display fr pvc-group  
Use the display fr interfacecommand to view frame relay state on the specified or all interfaces.  
Use the display fr lmi-infocommand to view the statistics of LMI protocol frame.  
Use the display fr map-infocommand to display frame relay (FR) address map information.  
Use the display fr map-infocommand to view all FR address maps or the one for the specified interface.  
Use the display fr pvc-groupcommand to view status, name, backup, protection, and other information  
about the specified PVC group, PVC groups on a specified interface, or all PVC groups if no argument is  
specified.  
Any view  
Any view  
display fr map-info pppofr  
Use the display fr map-info pppofr command to display information about the current PPPoFR map  
and its state.  
 
44  
3Com Router 5000/6000 Family  
Command Reference  
display fr pvc-infoc  
Use the display fr pvc-infocommand to view the frame relay PVC table.  
Any view  
display fr statistics  
Use the display fr statisticscommand to view the current Frame Relay statistics about receiving and  
sending packets.  
Any view  
display fr switch-table  
Use the display mfrcommand to view configuration and status information of the frame relay route to  
confirm the correctness of the configuration.  
Any view  
Any view  
Any view  
Any view  
display fr vofr-info  
display ft 1 serial  
display ftp-server  
Use the display fr vofr-infocommand to view the VoFR information.  
Use the display ft1 serialcommand to view the configuration and state of the T1-F interface.  
Use the display ftp-server command to view the parameters of the current FTP server.  
display ftp-server source-ip  
Use the display ftp-server source-ipcommand to display the source IP address configured for the FTP  
server.  
Any view  
Any view  
Any view  
Any view  
display ftp source-ip  
Use the display ftp source-ipcommand to display the source IP address configured for the FTP client.  
Use the display ftp-usercommand to view the parameters of the current FTP users.  
display ftp-user  
display history-command  
Use the display history-commandcommand to view the history commands.  
display hwatacs  
display hwping  
Use the display hwtacacscommand to view configuration information of specified or all TACACS+  
schemes.  
Any view  
Any view  
Any view  
Any view  
Any view  
Use the display hwpingcommand, you can view test result(s).  
display hwping statistics  
Use the display hwping statisticscommand to view test statistics.  
display icmp statistics  
Use the display icmp statisticscommand to view statistics about ICMP messages.  
display igmp group  
Use the display igmp groupcommand to view the member information of the IGMP multicast group.  
display igmp interface  
Use the display igmp interfacecommand to view the IGMP configuration and running information on an  
interface.  
Any view  
Any view  
display igmp local  
Use the display igmp localcommand to view the IGMP configuration and running information of the local  
interface which receives and sends multicast data.  
 
3Com Router 5000/6000 Family  
Command Reference  
45  
display ike dpd  
Use the display ike dpdcommand to display the configuration of the specified or all DPD structures about  
reference count, interval-time, and time_out.  
Any view  
Any view  
Any view  
Any view  
Any view  
display ike peer  
display ike proposal  
display ike sa  
Use the display ike peercommand to view the configuration about the specified or all IKE peers.  
Use the display ike proposalcommand to view the parameters configured for each IKE proposal.  
Use the display ike sacommand to view the current security tunnels established by IKE.  
Use the display info-centercommand to view all the information recorded in the info-center.  
display info-center  
display interface  
Use the display interfacecommand to view the LAPB or X.25 interface information. After configuring  
PVC of X.25, users can use the command to obtain the status information on one interface.  
Any view  
Any view  
display interface  
display interface  
Use the display interfacecommand to view configuration information on the port.  
Use the display interfacecommand to view the current running state and other information about an  
interface.  
Any view  
display interface atm  
Use the display interface atmcommand to display the configuration and state information about the  
specified or all ATM interfaces.  
Any view  
Any view  
display interface bri  
Use the display interface bricommand to view status about the specified ISDN BRI interface.  
display interface encrypt  
Use the display interface encryptcommand to view information about interfaces on the specified or all  
encryption cards.  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
display interface {Ethernet Gigabithernet}  
Use the display interface{ ethernet | gigabitethernet }command to view information about  
Ethernet interfaces, such as their configurations and current running state.  
display interface ima-group  
Use the display interface ima-groupcommand to view the configuration and state information about  
the specified or all IMA group interfaces.  
display interface loopback  
Use the display interface loopbackcommand to view state about the specified or all created loopback  
interfaces.  
display interface mfr  
Use the display interface mfrcommand to view information on one or all MFR interfaces, including  
configuration, state, and packet statistics.  
display interface mp-group  
Use the display interface mp-groupcommand to view the state about the specified or all MP-group  
interfaces.  
 
46  
3Com Router 5000/6000 Family  
Command Reference  
display interface null  
Use the display interface nullcommand to view the state about the null interface.  
Any view  
display interface pos  
Use the display interface poscommand to view the configuration and state information of one or all POS  
interfaces.  
Any view  
Any view  
display interface tunnel  
Use the display interface tunnelcommand to view the working status of tunnel interface.  
display interface virtual-ethernet  
Use the display interface virtual-ethernetcommand to view the state about of the specified or all  
virtual Ethernet interfaces.  
Any view  
display interface virtual-template  
Use the display interface virtual-templatecommand to view the state about the specified or all virtual  
templates.  
Any view  
Any view  
Any view  
display ip count  
Use the display ip countcommand to display IP packet statistics gathered by the IP Accounting.  
Use the display ip count rulecommand to display IP accounting rules.  
display ip count rule  
display ip fast-forwarding cache  
Use the display ip fast-forwarding cache command to view information on the unicast fast forwarding  
table.  
Any view  
Any view  
display ip host  
Use the display ip hostcommand to display all the host names and their corresponding IP addresses.  
display ip interface  
Use the display ip interfacecommand to view IP-related information about the specified or all  
interfaces.  
Any view  
display ip interface brief  
Use the display ip interface briefcommand to view IP-related summary about the specified or all  
interfaces.  
Any view  
Any view  
display ip ip-prefix  
Use the display ip ip-prefixcommand to view the address prefix list.  
display ip multicast-fast-forwarding cache  
Use the display ip multicast-fast-forwarding cache command to display summary information about  
the fast forwarding table entries in the multicast fast forwarding cache.  
Any view  
Any view  
display ip multicast-policy  
Use the display ip multicast-policycommand to view the multicast policy routing information.  
display ip netstream cache  
Use the display ip netstream cachecommand to view configuration and status information about the  
NetStream cache.  
Any view  
Any view  
display ip netstream export  
Use the display ip netstream exportcommand to view statistics about exported NetStream UDP  
packets.  
 
3Com Router 5000/6000 Family  
Command Reference  
47  
display ip policy  
Use the display ip policycommand to view the routing policies of local and configured interface policy  
routings.  
Any view  
Any view  
Any view  
Any view  
display ip policy setup  
Use the display ip policy setupcommand to view the setting information of policy routings.  
display ip policy statistic  
Use the display ip policy statisticcommand to view the statistics of policy routings.  
display ip routing-table  
Use the display ip routing-tablecommand to view the routing table summary.  
display ip routing-table acl  
Use the display ip routing-table aclcommand to view the route filtered through specified basic access  
control list (ACL).  
Any view  
Any view  
Any view  
Any view  
Any view  
display ip routing-table ip_address  
Use the display ip routing-tableip_addresscommand to view the routing information of the specified  
destination address.  
display ip routing-table ip_address1 ip_address2  
Use the display ip routing-tableip_address1 ip_address2command to view the routing  
information in the specified destination address range.  
display ip routing-table ip-prefix  
Use the display ip routing-table ip-prefixcommand to view the route that passed the filtering rule  
according to the specified ip prefix list.  
display ip routing-table protocol  
Use the display ip routing-table protocolcommand to view the routing information of specified  
protocol.  
display ip routing-table radix  
Use the display ip routing-table radixcommand to view the routing table information in a tree  
structure.  
Any view  
Any view  
Any view  
display ip routing-table statistics  
Use the display ip routing-table statistics command to view the integrated routing information.  
display ip routing-table verbose  
Use the display ip routing-table verbosecommand to view the verbose routing table information.  
display ip routing-table vpn-instance  
Use the display ip routing-table vpn-instancecommand to view RIP information associated with vpn  
instance address family.  
Any view  
display ip routing-table vpn-instance  
Use the display ip routing-table vpn-instancecommand to view the specified information in the IP  
routing table of vpn-instance.  
Any view  
Any view  
display ip socket  
Use the display ip socketcommand to display the information about all sockets in the current system.  
display ip statistics  
Use the display ip statisticscommand to view IP traffic statistics information. This command is used  
to display such statistics information as IP packet transmit/receive, packet assembly/disassembly, which is  
helpful to fault diagnosis.  
Any view  
 
48  
3Com Router 5000/6000 Family  
Command Reference  
display ip vpn-instance  
Use the display ip vpn-instancecommand to view the information related to vpn-instance, such as RD,  
description, and interfaces of the VPN instance.  
Any view  
Any view  
Any view  
Any view  
Any view  
display ipsec policy  
Use the display ipsec policycommand to view information about the ipsec policy.  
display ipsec policy-template  
Use the display ipsec policy-templatecommand to view information about the ipsec policy template.  
display ipsec proposal  
Use the display ipsec proposalcommand to view information about the proposal.  
display ipsec sa  
Use the display ipsec sacommand to view the relevant information about the SA.  
display ipsec statistics  
Use the display ipsec statisticscommand to view the IPSec packet statistics information, including  
the input and output security packet statistics, bytes, number of packets discarded and detailed description  
of discarded packets.  
Any view  
Any view  
display ipx interface  
Use the display ipx interface command to view IPX interface configuration information and interface  
parameters in communication devices.  
display ipx routing-table  
Use the display ipx routing-tablecommand to view active IPX routing information.  
Use the display ipx routing-table verbosecommand to view detailed IPX routing information, including  
active and inactive routes.  
Use the display ipx routing-table networkcommand to view active IPX routing information to specified  
destination network ID.  
Use the display ipx routing-table network verbosecommand to view detailed IPX routing information  
to specified destination network ID, including active and inactive routes.  
Use the display ipx routing-table protocol { rip | static | default | direct } command to view IPX routing  
information for specified destination type, including active and inactive routes.  
Use the display ipx routing-table protocol{ rip | static | default | direct } verbosecommand to view  
detailed IPX routing information for specified destination type, including active and inactive routes.  
Any view  
Any view  
display ipx routing-table statistics  
Use the display ipx routing-table statisticscommand to view IPX routing statistics.  
display ipx service-table  
Use the display ipx service-tablecommand to view contents of IPX service information table. The  
output information of the command helps users with IPX SAP troubleshooting.  
Any view  
display ipx statistics  
Use the display ipx statisticscommand to view statistics and type of IPX packet transmitted and  
received.  
Any view  
Any view  
Any view  
Any view  
display isdn active-channel  
Use the display isdn active-channelcommand to view the active call information on ISDN interfaces.  
display isdn call-info  
Use the display isdn call-infocommand to view the current states of ISDN interfaces.  
display isdn call-record  
Use the display isdn call-recordcommand to view the information of ISDN call history.  
 
3Com Router 5000/6000 Family  
Command Reference  
49  
display isdn parameters  
Use the display isdn parameterscommand to view the system parameters at layers 2 and 3 of the ISDN  
protocol, such as the durations of system timers and frame size.  
Any view  
display isdn spid  
display isis brief  
Use the display isdn spidcommand to view information on SPID on the BRI interface encapsulated with  
the NI protocol.  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Use the display isis briefcommand to view the brief information of IS-IS.  
display isis interface  
Use the display isis interfacecommand to view the information of the IS-IS enabled interface.  
display isis lsdb  
Use the display isis lsdbcommand to view the link state database of the IS-IS.  
display isis mesh-group  
Use the display isis mesh-groupcommand to view the IS-IS mesh group.  
display isis peer  
Use the display isis peercommand to view IS-IS peer information.  
Use the display isis routingcommand to view IS-IS routing information  
display isis routing  
display isis routing clns  
Use the display isis routing clnscommand to display CLNS routing information generated by IS-IS  
protocol.  
Any view  
Any view  
Any view  
display isis spf-log  
display llc2  
Use the display isis spf-logcommand to view the SPF calculation log of the IS-IS.  
Use the display llc2command to view statistical information of LLC2.  
display loadsharing ip address  
Use the display loadsharing ip addresscommand to view the statistics about the unbalanced load  
sharing based on interface bandwidth, including the number and ratio of the packets sent from the interfaces  
related to the equal-cost routes to a network address.  
Any view  
Any view  
display local-server statistics  
Use the display local-server statisticscommand to display statistics of the local RADIUS  
authentication server.  
display local-user  
Use the display local-usercommand to view the relevant information on the specified local user or all  
the local users. The output can help you troubleshoot faults related to local user.  
Any view  
User view  
Any view  
Any view  
display log startup  
display logbuffer  
Use the display log startupcommand to display the state of the configuration restoration log switch.  
Use the display logbuffercommand to view the information recorded in the log buffer.  
display logbuffer summary  
Use the display logbuffer summarycommand to display a summary about the log buffer on the router.  
 
50  
3Com Router 5000/6000 Family  
Command Reference  
display mac-address  
Use the display mac-addresscommand to display information about MAC address entries of an interface  
or about all MAC address entries.  
Any view  
Any view  
display memory  
display memory  
Use the display memorycommand to view information on system memory load.  
Use the display memorycommand to view the memory setting and state information related to the routing  
capacity.  
Any view  
display mfr  
Use the display mfrcommand to view configuration and statistics information of multilink frame relay  
bundle and bundle link. If no bundle or bundle link is specified, information of all bundles and bundle links  
will be displayed.  
Any view  
Any view  
display mirror  
Use the display mirrorcommand to display information about port mirroring configuration, information  
including the monitored ports, the direction of monitored packets and monitoring port.  
display mobile-ip binding  
Use the display mobile-ip bindingcommand to display information about the HA binding table. A  
binding table maintains mainly the corresponding relations between HA addresses and the care-of  
addresses of MNs. An HA updates the binding table based on MN registration events.  
Any view  
Any view  
display mobile-ip globals  
Use the display mobile-ip globalscommand to display global information about mobility agents.  
display mobile-ip interface  
Use the display mobile-ip interfacecommand to display the MIP information of an interface. With the  
interface-numberargument not specified, MIP information of all interfaces is displayed.  
Any view  
display mobile-ip irdp  
Use the display mobile-ip irdpcommand to display ICMP router discovery protocol (IRDP) configuration  
information, including the agent advertisement lifetime, the maximum and minimum agent advertisement  
interval, and the agent advertisement transmission mode (broadcast or multicast).  
Any view  
Any view  
Any view  
display mobile-ip mobile-router  
Use the display mobile-ip mobile-routercommand to display information about an MR, including basic  
information, discovered mobility agent information, registration information, and statistics.  
display mobile-ip node  
Use the display mobile-ip nodecommand to display information about MNs. With no parameters  
specified, information about all MNs is displayed.  
display mobile-ip secure  
Use the display mobile-ip securecommand to display mobility security association attributes. If not  
specify argument ip-address, information about all mobility security association attributes of the specified  
mobility security associations is displayed.  
Any view  
Any view  
display mobile-ip statistics  
Use the display mobile-ip statisticscommand to display statistics collected by the mobility agents.  
display mobile-ip violation  
Use the display mobile-ip violationcommand to display MN security exception information logged by  
a mobility agent. With the ip-address argument not specified, all security exception information is displayed;  
up to 100 latest entries of information can be displayed.  
Any view  
 
3Com Router 5000/6000 Family  
Command Reference  
51  
display mobile-ip visitor  
Use the display mobile-ip visitorcommand to display information in the visitor table and pending table  
of an FA. An FA updates its visitor table and pending table based on registration events of MNs. If not  
specify the ip-addressargument, all contents of the tables are displayed.  
Any view  
Any view  
display mpls l2vc  
Use the display mpls l2vccommand to view the VC information in LDP.  
display mpls l2vpn forwarding-info  
Use the display mpls l2vpn forwarding-infocommand to view the L2VPN information of a specific  
interface.  
Any view  
Any view  
display mpls l3vpn-lsp  
Use the display mpls l3vpn-lspcommand to view the information of vpn-instance of MPLS L3VPN LSPs.  
display mpls cell-transfer interface  
Use the display mpls cell-transfer interfacecommand to view statistics for cells received and sent  
in a packet on an interface in transparent transmission mode.  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
display mpls interface  
Use the display mpls interfacecommand to view all MPLS-enabled interfaces.  
Use the display mpls ldpcommand to view LDP and LSR information.  
display mpls ldp  
display mpls ldp buffer-info  
Use the display mpls ldp buffer-infocommand to view the buffer information of LDP.  
display mpls ldp interface  
Use the display mpls ldp interfacecommand to view the information of an LDP-enabled interface.  
display mpls ldp lsp  
display mpls ldp peer  
Use the display mpls ldp lspcommand to view relevant LSP information created via LDP.  
Use the display mpls ldp peercommand to view peer information.  
display mpls ldp remote  
Use the display mpls ldp remotecommand to view the configured remote peer information.  
display mpls ldp session  
Use the display mpls ldp sessioncommand to display the session between peer entities.  
display mpls lsp  
Use the display mpls lspcommand to view LSP information.  
display mpls static-lsp  
Use the display mpls static-lspcommand to view the information of all or one static LSP(s).  
display mpls statistics  
Use the display mpls statisticscommand to view statistics of all or one LSP(s) and LSP statistics on  
all or one interface(s).  
Any view  
Any view  
Any view  
display msdp brief  
Use the display msdp briefcommand to view the state of MSDP peer.  
display msdp peer-status  
Use the display msdp peer-statuscommand to view the detailed information of MSDP peer.  
 
52  
3Com Router 5000/6000 Family  
Command Reference  
display msdp sa-cache  
display msdp sa-count  
Use the display msdp sa-cachecommand to view (S, G) state learnt from MSDP peer.  
Any view  
Use the display msdp sa-countcommand to view the number of sources and groups in MSDP cache.  
Any view  
display multicast forwarding-table  
Use the display multicast forwarding-tablecommand to view the information of multicast forwarding  
table.  
Any view  
Any view  
display multicast routing-table  
Use the display multicast routing-tablecommand to view the information of IP multicast routing table.  
display multicast routing-table static  
Use the display multicast routing-table staticcommand to view the configuration information of  
static multicast route.  
Any view  
Any view  
display multicast routing-table static  
Use the display multicast routing-table staticcommand to view the active multicast static routes.  
display multicast routing-table static config  
Use the display multicast routing-table static configcommand to view multicast static routes  
configured.  
Any view  
display multicast rpf-info  
Use the display multicast rpf-infocommand to view the Reverse Path Forwarding (RPF) routing  
information for specified multicast source.  
Any view  
Any view  
Any view  
display nat  
Use the display natcommand to display the configuration of address translation.  
display nat connection-limit  
Use the display nat connection-limitcommand to display the NAT-related connection limit statistics.  
display ntp-service sessions  
Use the display ntp-service sessionscommand to view brief information about all sessions maintained  
by the NTP at the local device.  
Any view  
Any view  
display ntp-service status  
Use the display ntp-service statuscommand to view status about the NTP service.  
display ntp-service trace  
Use the display ntp-service trace command to view the summary about each NTP time server from  
the local device back to the reference clock source.  
Any view  
Any view  
display osm status slot  
Use the display osm status slot slotnumcommand to view the information about the OSM board in the  
specified slot, including name of the board, board status, OS name, OS version and running time of OS.  
display ospf abr-asbr  
Use the display ospf abr-asbrcommand to view information on the routes to the Area Border Router  
(ABR) and Autonomous System Border Router (ASBR) of OSPF.  
Any view  
Any view  
Any view  
display ospf asbr-summary  
Use the display ospf asbr-summarycommand to view summary about the redistributed routes of OSPF.  
display ospf brief  
Use the display ospf briefcommand to view the summary of OSPF.  
 
3Com Router 5000/6000 Family  
Command Reference  
53  
display ospf cumulative  
Use the display ospf cumulativecommand to view the OSPF cumulative information.  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
display ospf error  
Use the display ospf errorcommand to view the statistics of error information which OSPF received.  
display ospf interface  
Use the display ospf interfacecommand to view the OSPF interface information.  
display ospf lsdb  
display ospf memory  
display ospf nexthop  
display ospf peer  
Use the display ospf lsdbcommand to view the database information about OSPF connecting state.  
Use the display ospf memorycommand to view memory occupation status for LSAs.  
Use the display ospf nexthopcommand to view the information about the next-hop  
Use the display ospf peercommand to view the information about the neighbors in OSPF areas.  
Use the display ospf peer briefcommand to view the brief information of neighbors in OSPF, mainly  
the neighbor number at all states in every area.  
Any view  
Any view  
display ospf request-queue  
Use the display ospf request-queuecommand to view the information about the OSPF request-queue.  
display ospf retrans-queue  
Use the display ospf retrans-queuecommand to view the information about the OSPF retransmission  
queue.  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
display ospf routing  
Use the display ospf routingcommand to view the information about OSPF routing table.  
display ospf sham-link  
Use the display ospf sham-linkcommand to view the information of sham links.  
display ospf vlink  
display pim bsr-info  
display pim interface  
display pim neighbor  
Use the display ospf vlinkcommand to view the information about OSPF virtual links.  
Use the display pim bsr-infocommand to view Bootstrap Router (BSR) information.  
Use the display pim interfacecommand to view the PIM interface information.  
Use the display pim neighborcommand to view the PIM neighbor information.  
display pim routing-table  
Use the display pim routing-tablecommand to view the contents of the PIM multicast routing table.  
display pim rp-info  
Use the display pim rp-infocommand to view the corresponding RP information of multicast group, BSR  
and static RP information.  
Any view  
Any view  
display pki certificate  
Use the display pki certificatecommand to display and browse through the certificate.  
 
54  
3Com Router 5000/6000 Family  
Command Reference  
display pki crl  
display port  
Use the display pki crlcommand to display and browse through the locally saved CRL.  
Any view  
Use the display portcommand to check whether the current system has hybrid or trunk ports. If there is  
any, its port name is displayed.  
Any view  
Any view  
Any view  
display port-mapping  
display portal  
Use the display port-mappingcommand to view PAM information.  
Use the display portalcommand to display the information about portal servers.  
display portal update-resource  
Use the display portal update-resourcecommand to display information about the update resources  
configured by the user.  
Any view  
Any view  
Any view  
display pos-app  
Use the display pos-appcommand to display brief information about POS applications.  
Use the display pos-interfacecommand to display brief information about POS access ports.  
display pos-interface  
display ppp compression iphc rtp  
Use the display ppp compression iphc rtpcommand to view the statistic information of the RTP header  
compression.  
Any view  
Any view  
display ppp compression iphc tcp  
Use the display ppp compression iphc tcpcommand to view the statistic information of the TCP header  
compression.  
display ppp compression stac-lzs  
Use the display ppp compression stac-lzscommand to view information about STAC-LZS  
compression.  
Any view  
Any view  
Any view  
display ppp mp  
Use the display pppmpcommand to view all interface information and statistics of MP.  
display pppoe-server session  
Use the display pppoe-server sessioncommand to view the status and statistics of PPPoE session.  
display pppoe-server session  
The command display pppoe-client sessionis used to display the status and statistics of PPPoE  
session.  
Any view  
Any view  
display protocol-priority  
Use the display protocol-prioritycommand to view protocol priorities.  
display qos car interface  
Use the display qos car interface command to view parameter configuration and running statistics of  
CAR at each or all interfaces.  
Any view  
Any view  
display qos carl  
Use the display qos carlcommand to view a certain rule or all the rules of CARL.  
display qos cbq interface  
Use the display qos cbq interfacecommand to view CBQ configuration information and operating  
status, the specified PVC on specified ATM interface or on all interfaces.  
Any view  
 
3Com Router 5000/6000 Family  
Command Reference  
55  
display qos cq interface  
Use the display qos cq interfacecommand to view configuration and statistics of customized queues  
(CQ) at interfaces.  
Any view  
Any view  
display qos cql  
Use the display qos cqlcommand to view contents of customized queue lists (CPL).  
display qos gts interface  
Use the display qos gts interfacecommand to view GTS configuration and accounting information of  
certain interface or all interfaces.  
Any view  
Any view  
display qos lr interface  
Use the display qos lr interfacecommand to view LR configuration and statistics of an interface.  
display qos policy  
Use the display qos policycommand to display the configuration information of the specified class or all  
the classes and associated behaviors in the specified policy or all policies.  
Any view  
Any view  
display qos policy interface  
Use the display qos policy interface command to view information about CBQ application on the  
interface.  
display qos policy interface  
Use the display qos policy interfacecommand to view the configuration and operating state about the  
policy on the specified interface, on the specified PVC on a particular ATM interface or on all interfaces and  
PVCs.  
Any view  
display qos pq interface  
Use the display qos pq interfacecommand to view the configuration and statistics of priority queues  
(PQ) at interfaces.  
Any view  
Any view  
display qos pql  
Use the display qos pqlcommand to view contents of priority queue lists (PQL).  
display qos rtpq interface  
Use the display qos rtpq interfacecommand to view information of the current IP RTP Priority queue,  
including the current RTP queue depth and number of RTP packets dropped, and display the RTP priority  
queue configuration and statistics on an interface or on all interfaces.  
Any view  
Any view  
Any view  
Any view  
display qos wfq interface  
Use the display qos wfq interfacecommand to view WFQ (weighted fair queuing) configuration and  
statistics of an interface.  
display qos wred interface  
Use the display qos wred interfacecommand to view WRED (weighed random early detection)  
configuration and statistics of an interface.  
display radius  
Use the display radiuscommand to view the configuration information about the specified or all RADIUS  
schemes or to view statistics about RADIUS.  
display radius statistics  
Use the display radius statisticscommand to view the statistics information on RADIUS packets. The  
displayed packet information can help you troubleshoot RADIUS faults.  
Any view  
Any view  
display rip  
Use the display ripcommand to view the current RIP running state and its configuration information.  
 
56  
3Com Router 5000/6000 Family  
Command Reference  
display rip interface  
Use the display rip interfacecommand to display information about the specified RIP interface or all  
RIP interface.  
Any view  
display rip routing  
Use the display rip routingcommand to display the RIP routing table, including normal routes and  
routes in garbage-collection status.  
Any view  
Any view  
display rip vpn-instance  
Use the display rip vpn-instancecommand to view the related configuration of VPN instance of RIP.  
display rmon alarm  
Use the display rmon alarmcommand to display the alarm table of remote monitoring (RMON) or the  
specified alarm entry.  
Any view  
Any view  
display rmon event  
Use the display rmon eventcommand to display the event table of RMON or the specified event entry.  
display rmon eventlog  
Use the display rmon eventlogcommand to display the log table of RMON or the log entry for the  
specified event.  
Any view  
Any view  
Any view  
display rmon history  
Use the display rmon historycommand to display the history control table of RMOM and information  
about the latest sampling, such as utilization, number of errors and total number of packets.  
display rmon prialarm  
Use the display rmon prialarmcommand to display information about the prialarm table of RMON or the  
specified prialarm entry.  
display rmon statistics  
Use the display rmon statisticscommand to display the RMON statistics about the specified or all  
interfaces.  
Any view  
Any view  
display route-policy  
Use the display route-policycommand to view the configured route-policy  
display rsa local-key-pair public  
Use the display rsa local-key-pair publiccommand to view the public key of the host key pair and  
server key pair on the server. If no key is generated, the system displays: RSA keys not found.  
Any view  
display rsa peer-public-key  
Use the display rsa peer-public-keycommand to view the specified RSA public key. If no public key  
specified, all public keys are displayed.  
Any view  
Any view  
display saved-configuration  
Use the display saved-configurationcommand to view the configuration file loaded at this startup.  
display schedule reboot  
Use the display schedule rebootcommand to view settings related to the router’s schedule reboot  
terminal service.  
Any view  
display sftp source-ip  
Use the display sftp source-ipcommand to display the source IP address configured for the SFTP  
client.  
Any view  
Any view  
display snmp-agent  
Use the display snmp-agentcommand to view the engine ID of the local or remote SNMP entity.  
 
3Com Router 5000/6000 Family  
Command Reference  
57  
display snmp-agent community  
Use the display snmp-agent communitycommand to view information on the configured communities of  
SNMPv1 or SNMPv2.  
Any view  
display snmp-agent group  
Use the display snmp-agent groupcommand to view information about the specified or all user security  
model (USM) based groups, including group name, security model, storage type.  
Any view  
Any view  
Any view  
Any view  
display snmp-agent mib-view  
Use the display snmp-agent mib-viewcommand to view the configured MIB views.  
display snmp-agent statistics  
Use the display snmp-agent statisticscommand to view the state and statistics about SNMP.  
display snmp-agent sys-info  
Use the display snmp-agent sys-infocommand to view the system information of this SNMP device.  
display snmp-agent trap-list  
Use the display snmp-agent trap-listcommand to display whether trap sending is enabled on each  
module.  
Any view  
display snmp-agent usm-user  
Use the display snmp-agent usm-usercommand to view information about the specified or all SNMP  
users.  
Any view  
Any view  
Any view  
display sot  
Use the display sotcommand to display the current state about SOT connections.  
Use the display ssh servercommand to view information on SSH status or sessions.  
display ssh server  
display ssh server-info  
Use the display ssh server-infocommand to view the associations of public key to SSH server  
maintained at the client end.  
Any view  
Any view  
display ssh-server source-ip  
Use the display ssh-server source-ipcommand to display the source IP address configured for the SSH  
server.  
display ssh user-information  
Use the display ssh user-informationcommand to view information about current SSH users, including  
user name, corresponding key name and user authentication mode. If you specify the username  
parameter, then only the information about the specified user is displayed.  
Any view  
Any view  
display ssh2 source-ip  
Use the display ssh2 source-ipcommand to display the source IP address configured for the SSH client.  
display standby flow  
Use the display standby flowcommand to view statistics about the traffic on the main interfaces  
participating in backup load sharing.  
Any view  
Any view  
display standby state  
Use the display standby statecommand to view information about the main and standby interfaces.  
display startup  
Use the display startupcommand to view the configuration file used at this startup and the one used for  
next startup.  
User view  
 
58  
3Com Router 5000/6000 Family  
Command Reference  
display status interface  
Use the display status interfacecommand to display the state of the specified interface.  
Any view  
display status interface ima-group  
Use the display status interface ima-groupcommand to view detailed information about the specified  
IMA group interface.  
Any view  
display stop-accounting-buffer  
Use the display stop-accounting-buffercommand to view information on the stop-accounting requests  
buffered in the router.  
Any view  
Any view  
Any view  
display tcp statistics  
Use the display tcp statisticscommand to view TCP traffic statistic information.  
Use the display tcp statuscommand to monitor TCP connection any time.  
display tcp status  
display tcp status  
Use the display tcp statuscommand to view information about the current TCP connections on the  
router.  
Any view  
display telnet-server source-ip  
Use the display telnet-server source-ipcommand to display the source IP address configured for the  
Telnet server.  
Any view  
Any view  
display tftp-server  
Use the display tftp-servercommand to view TFTP server state and attributes setting.  
display tftp source-ip  
Use the display tftp source-ipcommand to display the source IP address configured for the TFTP  
client.  
Any view  
Any view  
display this  
Use the display thiscommand to view the current configurations in current view.  
display time-range  
Use the display time-rangecommand to view the configuration and the status of time range. For the  
active time range at present, it displays "active" and for the inactive time range, it displays "inactive".  
Any view  
Any view  
display traffic behavior  
Use the display traffic behaviorcommand to display the information of the traffic behavior configured  
on the router.  
display traffic classifier  
Use the display traffic classifiercommand to view the configuration information about class of the  
router.  
Any view  
Any view  
display trapbuffer  
Use the display trapbuffercommand to view the information entries in the trap buffer.  
display udp-helper server  
Use the display udp-helper servercommand to display the information about the destination servers  
associated with the specified or all Ethernet interfaces.  
Any view  
Any view  
display udp statistics  
Use the display udp statisticscommand to view TCP traffic statistic information.  
 
3Com Router 5000/6000 Family  
Command Reference  
59  
display user-interface  
Use the display user-interfacecommand to view information about the specified or all user interfaces.  
Any view  
Any view  
Any view  
display users  
Use the display userscommand to view the login information of the users on each user interface.  
Use the display versioncommand to system version information.  
display version  
display virtual-access  
Use the display virtual-accesscommand to view state information about the specified or all virtual  
access interfaces.  
Any view  
Any view  
display vlan  
Use the display vlancommand to view information on VLANs.  
display vlan interface  
Use the display vlan interfacecommand to view VLAN configuration information on a certain interface  
(only supporting sub-interface).  
Any view  
Any view  
Any view  
display vlan max-packet-process  
Use the display vlan max-packet-processcommand to view the maximum number of processed packets  
configured on a certain VLAN per second.  
display vlan statistics vid  
Use the display vlan statistics vidcommand to view the packet statistics on a certain VLAN, e.g. the  
received packet number and the sent packet number.  
display vlan statistics vid  
Use the display vlan statistics vidcommand to view the packet statistics on a certain VLAN, e.g. the  
received packet number and the sent packet number.  
Any view  
Any view  
Any view  
Any view.  
display voice aaa-client configuration  
Use the display voice aaa-client configurationcommand to view information about voice AAA.  
display voice call-history-record  
Use the display voice call-history-recordcommand to view the information about call history records.  
display voice call-history-record  
Use the display voice call-history-recordcommand to view call history.  
display voice call-info  
Use the display voice call-infocommand to view the call information table, including: channel number  
of the call, reference counter of all voice modules, module ID in use, list of the voice entities that can be  
selected by the current call, and the voice entity used by the current call.  
Any view  
Any view  
Any view  
Any view  
display voice default  
Use the display voice defaultcommand to view the current default values and the system-fixed default  
values for voice and fax.  
display voice em call-statistic  
Use the display voice em call-statisticcommand to view the call statistics of the digital E&M  
subscriber-line.  
display voice em ccb  
Use the display voice em ccbcommand to view the information of call control block of the E&M  
subscriber-line.  
 
60  
3Com Router 5000/6000 Family  
Command Reference  
display voice entity  
Use the display voice entitycommand to view the configuration information of voice entities of different  
types.  
Any view  
display voice fax  
Use the display voice faxcommand to view the fax statistics in the fax module and the statistics in the  
fax transformation module as well.  
Any view  
Any view  
Any view  
display voice gateway  
Use the display voice gatewaycommand to view the gateway registration state information to GK Server.  
Use the display voice ippcommand to view statistics about the IPP module.  
display voice ipp  
display voice number-substitute  
Use the display voice number-substitutecommand to view the configuration information of  
number-substitute lists. It can display the information of a certain list and all the lists.  
Any view  
Any view  
display voice r2 call-statistics  
Use the display voice r2 call-statisticscommand to view the R2 call statistics.  
display voice rcv ccb  
Use the display voice rcv ccbcommand to view the information related to the call control block in the  
RCV module.  
Any view  
Any view  
Any view  
Any view  
Any view  
display voice rcv statistic  
Use the display voice rcv statisticcommand to view the statistics information of calling between the  
RCV module and the CC module, VAS module, and so on.  
display voice rcv statistic r2  
Use the display voice rcv statistic r2command to view the information of call statistics related to the  
R2 signaling in the RCV module.  
display voice sip call-statistics  
Use the display voice sip call-statisticscommand to view all statistic information about the SIP  
client.  
display voice sip register-state  
Use the display voice sip register-statecommand to view the registration state about the SIP user  
agents (UAs).  
display voice sip register status  
Use the display voice sip register statuscommand to display the registration status information of  
all subscriber numbers under SIP UAs. The information includes subscriber number (Number), entity  
number (Entity), timeout time (Expires) and registration status (Status).  
Any view  
display voice subscriber-line  
Use the display voice subscriber-linecommand to view the configuration information about the type,  
status, codec mode, input gain and output attenuation of the subscriber line.  
Any view  
Any view  
Any view  
display voice subscriber-line  
Use the display voice subscriber-linecommand to view the subscriber line configuration.  
display voice vofr call  
Use the display voice vofr callcommand to view information of the current call.  
display voice vofr statistic  
Use the display voice vofr statistic command to view the call statistics between the VoFR module  
and VCC, VPP and other modules.  
Any view  
 
3Com Router 5000/6000 Family  
Command Reference  
61  
display voice voip data-statistic  
Use the display voice voip data-statisticcommand to view statistics information of voice data.  
Any view  
Any view  
display voice vpp  
display voice vcc  
Use the display voice vppcommand to view all the statistic information in the VPP module.  
Use the display voice vcccommand to view the information about the call channel status and call  
statistics.  
Any view  
display voice voip  
Use the display voice voip downqueuee1t1vi-bnocommand to display the contents of the down  
interrupt queue between the E1/T1 voice card and the router main card.  
Use the display voice voip up-queuee1t1vi-nocommand to display the contents of the up interrupt  
queue between the E1/T1 voice card and the router main card.  
Use the display voice voip phy-statistice1t1vi-bnocommand to display the statistics of the  
physical layer.  
Any view  
Any view  
Any view  
Any view  
display vrrp  
Use the display vrrpcommand to view current configuration and state information about VRRP.  
display web java-blocking  
Use the display web java-blockingcommand to display the information about Java blocking.  
display web url-filter host  
Use the display web url-filter hostcommand to display information about URL address filtering.  
display web url-filter parameter  
Use the display web url-filter parametercommand to display the filtering information about SQL  
attack.  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
Any view  
display x25 alias-policy  
Use the display x25 alias-policycommand to view X.25 alias table.  
display x25 cug  
Use the display x25 cug command to view the CUG configuration on the router ports.  
display x25 hunt-group-info  
Use the display x25 hunt-group-infocommand to view the status information of X.25 hunt group.  
display x25 map  
display x25 map  
display x25 pad  
Use the display x25 mapcommand to view the X.25 address mapping table.  
Use the display x25 mapcommand to display X.25 address map information.  
Use the display x25 padcommand to view X.25 PAD connection information.  
display x25 switch-table pvc  
Use the display x25 switch-table pvccommand to view X.25 switching virtual circuit table.  
display x25 switch-table svc  
Use the display x25 switch-table svccommand to display the X.25 switching routing table.  
display x25 vc  
Use the display x25 vccommand to display information about X.25 virtual circuits.  
 
62  
3Com Router 5000/6000 Family  
Command Reference  
display x25 x2t switch-table  
Use the display x25 x2t switch-tablecommand to display the dynamic switching routing table and  
static routing table.  
Any view  
Any view  
display x25 xot  
Use the display x25 xotcommand to view XOT link information.  
Use the dl-bitscommand to configure the bit value of all the signals of R2 line signaling.  
dl-bits  
R2 CAS view  
dlsw bridge-set  
Use the dlsw bridge-setcommand to configure the bridge group to connect DLSw. Use the undo dlsw  
bridge-setcommand to delete the bridge.  
System view  
System view  
dlsw enable  
Use the dlsw enablecommand to enable DLSw performance.  
dlsw ethernet-backup enable  
Use the dlsw ethernet-backup enablecommand to enable DLSw Ethernet redundancy.  
Ethernet Interface view  
dlsw ethernet-backup map  
Use the dlsw ethernet-backup mapcommand to enable the Ethernet switch support feature for DLSw  
Ethernet redundancy, that is, to map the MAC address of a remote SNA device to a local virtual MAC  
address.  
Ethernet Interface view  
dlsw ethernet-backup timer  
Use the dlsw ethernet-backup timercommand to configure the time for which the master DLSw router  
waits before sending a positive or negative response to the slave DLSw router upon receipt of a circuit  
establishing request.  
Ethernet Interface view  
dlsw ethernet-frame-filter  
Use the dlsw ethernet-frame-filtercommand to apply an ACL in the transmitting and receiving  
directions of DLSW module towards bridge module so that it can transmit and receive only the Ethernet  
frames with permitted source MAC addresses.  
System view  
System view  
System view  
dlsw filter acl  
dlsw local  
Use the dlsw filter aclcommand to specify to filter packets from any peer.  
Use the dlsw localcommand to create the DLSw local peer.  
dlsw max-transmission  
Use the dlsw max-transmissioncommand to set the maximum number of the attempts to send an explorer  
frame.  
System view  
System view  
System view  
dlsw multicast  
Use the dlsw multicastcommand to enable the multicast function of DLSw2.0.  
dlsw reachable  
Use the dlsw reachablecommand to configure locally reachable MAC and SAP addresses.  
dlsw reachable-cache  
Use the dlsw reachable-cachecommand to add the reachability information of the specified SNA device  
to the reachable-cache. You can specify this SNA device by specifying its MAC address and IP address of  
the router to which it is connected.  
System view  
System view  
dlsw remote  
Use the dlsw remotecommand to create the DLSw remote peer.  
 
3Com Router 5000/6000 Family  
Command Reference  
63  
dlsw remote  
Use the dlsw remotecommand to create a remote DLSw peer and specifies its version and filtering rule.  
System view  
dlsw reverse  
Use the dlsw reverse command to convert a MAC address from Ethernet order to token ring order or vice  
versa.  
System view  
System view  
System view  
dlsw timer  
dns domain  
dns-list  
Use the dlsw timercommand to configure the DLSw timer parameters.  
Use the dns domaincommand to configure a DNS domain name.  
Use the dns-listcommand to configure DNS server IP addresses in a global DHCP address pool.  
DHCP Address Pool view  
System view  
dns-proxy enable  
dns resolve  
dns server  
domain  
Use the dns-proxy enablecommand to enable DNS proxy.  
Use the dns resolvecommand to enable DNS resolving.  
System view  
Use the dns servercommand to configure IP address of a DNS server.  
Use the domaincommand to configure an ISP domain or enter the view of an existing ISP domain.  
System view  
System view  
domain-authentication-mode  
Use the domain-authentication-modecommand to configure IS-IS route area to authenticate the received  
Level-2 routing packets (LSP, CSNP, PSNP), according to the pre-defined mode and password.  
IS-IS view  
domain-id  
Use the domain-id command to specify domain ID for a VPN instance.  
OSPF Protocol view  
domain-name  
Use the domain-namecommand to configure the domain name that a global address pool of the DHCP  
server allocates to clients.  
DHCP Address Pool view  
Voice Number-Substitute view  
IKE Peer view  
dot-match  
Use the dot-matchcommand to configure dot match rules of the number-substitute rules.  
Use the dpdcommand to reference a DPD structure.  
dpd  
dscp media  
Use the dscp mediacommand to set the DSCP value in the ToS field in the IP packets that carry the RTP  
stream of the voice entity.  
Voice Entity view  
dsl link-check  
Use the dsl link-check enablecommand to enable retraining upon detection of a major fault after the  
DSL interface comes up.  
ATM (G.SHDSL) Interface view  
dtmf  
Use the dtmfcommand to configure the way of sending and receiving R2 signaling.  
R2 CAS view  
dtmf sensitivity-level  
Use the dtmf sensitivity-levelcommand to set the detection sensitivity level of DTMF codes.  
Voice Subscriber-Line view  
 
64  
3Com Router 5000/6000 Family  
Command Reference  
dtmf threshold  
Use the dtmf thresholdcommand to configure the sensitivity of DTMF digit detection.  
Use the duplexcommand to set the operating mode of the Ethernet interface.  
Use the duplexcommand to configure the duplex mode of the Ethernet port.  
Use the dvpn classcommand to create and enter a dvpn-class view.  
Voice Subscriber-Line view  
Ethernet Interface view  
Ethernet Port view  
duplex  
duplex  
dvpn class  
System view  
dvpn client register-dumb  
Use the dvpn client register-dumbcommand to set the time when a client turns to dumb state after it  
fails to register with a DVPN server for specified retries.  
System view  
System view  
dvpn client register-interval  
Use the dvpn client register-intervalcommand to set the register interval of a client.  
dvpn client register-retry  
Use the dvpn client register-retry command to set the maximum retries for a client to register with a  
DVPN server continuously.  
System view  
dvpn dvpn-id  
Use the dvpn dvpn-idcommand to specify the DVPN domain the tunnel interface belongs to. This  
command is valid when the tunnel interface is encapsulated as DVPN.  
Tunnel Interface view  
dvpn interface-type  
Use the dvpn interface-typecommand to specify the type of a tunnel interface. A tunnel interface is of  
client type by default.  
Tunnel Interface view  
System view  
dvpn policy  
Use the dvpn policycommand to create and enter a DVPN policy view.  
dvpn policy  
Use the dvpn policycommand to apply a specified DVPN policy to a tunnel interface that is of server type.  
Tunnel Interface view  
dvpn register-type  
Use the dvpn register-typecommand to configure the type of the additional information when a client  
registers with a DVPN server.  
Tunnel Interface view  
dvpn security  
Use the dvpn security acl command to configure the ACL used for deciding which data stream needs  
IPSec encryption on the tunnel interface.  
Tunnel Interface view  
Tunnel Interface view  
dvpn server  
Use the dvpn servercommand to configure the DVPN class to be applied to a tunnel interface.  
dvpn server authentication-client method  
Use the dvpn server authentication-client methodcommand to specify the default way a DVPN server  
authenticates clients.  
System view  
System view  
System view  
dvpn server map age-time  
Use the dvpn server map age-timecommand to set the map age time of a DVPN server.  
dvpn server pre-shared-key  
Use the dvpn server pre-shared-keycommand to set a pre-shared key for a DVPN server.  
 
3Com Router 5000/6000 Family  
Command Reference  
65  
dvpn service  
Use the dvpn service enablecommand to enable DVPN on a device.  
System view  
CE3 interface view  
CE3 Interface view  
CPOS Interface view  
CE3 Interface view  
CPOS Interface view  
CE3 Interface view  
CPOS Interface view  
CE3 Interface view  
CPOS Interface view  
CE3 Interface view  
CPOS Interface view  
CE3 Interface view  
CPOS Interface view  
SIP Client view  
e1 bert  
Use the e1 bertcommand to set test error bit for line Bit on CE3 interface.  
e1 channel-set  
e1 channel-set  
e1 set clock  
e1 set clock  
e1 set frame-format  
e1 set frame-format  
e1 set loopback  
e1 set loopback  
e1 shutdown  
Use the e1 channel-setcommand to bundle timeslots on an E1 line.  
Use the e1 channel-setcommand to bundle multiple timeslots on an E1 channel into one channel set.  
Use the e1 set clockcommand to set clocking of an E1 line on the CE3 interface.  
Use the e1 set clockcommand to set the clock mode of the E1 channel.  
Use the e1 set frame-formatcommand to configure the frame format on an E1 line.  
Use the e1 set frame-formatcommand to set the frame format of an E1 channel.  
Use the e1 set loopbackcommand to set the loopback mode of the specified E1 line on the E3 interface.  
Use the e1 set loopbackcommand to configure the loopback mode of the E1 channel.  
Use the e1 shutdowncommand to shut down an E1 line on the CE3 interface.  
Use the e1 shutdowncommand to shut down an E1 channel.  
e1 shutdown  
e1 unframed  
Use the e1 unframedcommand to set an E1 line on a CE3 interface to work in unframed mode (E1 mode).  
Use the e1 unframed command to set an E1 channel on the CPOS interface to unframed mode or E1 mode.  
Use the early-media disablecommand to disable early media negotiation.  
Use the ebscommand to set EBS of frame relay virtual circuit.  
e1 unframed  
early-media disable  
ebs  
Frame Relay Class view  
Voice Subscriber-Line view  
R2 CAS view  
echo-canceller  
effect-time  
Use the echo-cancellercommand to configure echo-cancellation parameters.  
Use the effect-timecommand to configure the debounce time of line signaling.  
eliminate-pulse  
Use the eliminate-pulsecommand to eliminate the pulses with a width less than 3.472us, increasing  
signal reliability. This is useful when the line is seriously interfered.  
Asynchronous Serial Interface view  
 
66  
3Com Router 5000/6000 Family  
Command Reference  
em-phy-parm  
em-signal  
Use the em-phy-parmcommand to configure a wire scheme for the analog E&M subscriber-line.  
Voice Subscriber-Line view  
Voice Subscriber-Line view  
NetStream Aggregation view  
Use the em-signalcommand to configure a voice subscriber-line start mode.  
Use the enablecommand to enable current aggregation mode.  
enable  
enable deactivate  
Use the enable deactivatecommand to enable the router to actively deactivate the BSV interface.  
BSV Interface view  
Interface view  
MR view  
enable snmp trap undown  
Use the enable snmp trap updowncommand to enable the interface to send UPDOWN traps.  
encapsulation  
Use the encapsulation grecommand to set the MR encapsulation mode to GRE.  
Use the encapsulationcommand to specify ATM AAL5 encapsulation type for PVC.  
encapsulation  
PVC view  
encapsulation-mode  
Use the encapsulation-modecommand to set the encapsulation mode that the security protocol applies to  
IP packets, which can be transport or tunnel.  
IPSec Proposal view  
System view  
encrypt-card backuped  
Use the encrypt-card backupedcommand to enable backup function for the encryption card.  
encrypt-card fast-switch  
Use the encrypt-card fast-switchcommand to enable the fast forwarding function of the encryption card.  
System view  
encryption-algorithm  
Use the encryption-algorithmcommand to specify the encryption algorithm for an IKE proposal.  
IKE Proposal view  
entity  
Use the entitycommand to configure a voice entity and enter its view (at the same time specify the working  
mode related to voice).  
Voice Dial Program view  
error-diffusion restraint config  
Use the error-diffusion restraint configcommand to set the three parameters for error diffusion  
restraint function.  
System view  
System view  
error-diffusion restraint enable  
Use the error-diffusion restraint enablecommand to enable error diffusion restraint.  
Use the escape-keycommand to define an escape key or key combination for aborting tasks.  
Use the esiscommand to employ ES-IS protocol globally and enter ES-IS view.  
Use the esis enablecommand to employ ES-IS protocol on the interface.  
escape-key  
esis  
User Interface view  
System view  
esis enable  
Interface view  
esp authentication-algorithm  
Use the esp authentication-algorithmcommand to set the authentication algorithm used by ESP.  
IPSec Proposal view  
 
3Com Router 5000/6000 Family  
Command Reference  
67  
esp encryption-algorithm  
Use the esp encryption-algorithmcommand to set the encryption algorithm adopted by ESP.  
IPSec Proposal view  
IKE-Peer view  
exchange-mode  
execute  
Use the exchange-modecommand to select an IKE negotiation mode.  
Use the executecommand to execute the specified batch file.  
System view  
exit  
Use the exitcommand to terminate the connection to the remote SFTP server and exit to system view as  
you would with the byeand quitcommands.  
SFTP Client view  
expired  
Use the expiredcommand to configure a valid period allowed for leasing IP addresses in a global DHCP  
address pool.  
DHCP Address Pool view  
VoIP Voice Entity view  
Voice Entity view  
fast-connect  
fax baudrate  
fax ecm  
Use the fast-connectcommand to enable fast connect.  
Use the fax baudratecommand to configure the highest fax baudrate enabled by the gateway.  
Use the fax ecmcommand to configure the forced adoption of ECM mode at the gateway, that is, to make  
the facsimiles at both ends support ECM mode.  
Voice Entity view  
Voice Entity view  
Voice Entity view  
Voice Entity view  
fax level  
Use the fax levelcommand to configure the gateway carrier transmitting energy level.  
fax local-train threshold  
Use the fax local-traincommand to configure the percentage of fax local training threshold value.  
fax nsf-on  
Use the fax nsf-oncommon to configure the fax faculty transmission mode as Not Standard mode.  
fax protocol  
Use the fax protocolcommand to configure the protocol for intercommunication with other devices or  
enable the fax Passthrough mode, and configure the number of redundant packets sent via the T.38 fax  
protocol. The argument standard-t38 indicates the standard T38 negotiation mode specified by H323 or SIP  
adopted.  
Voice Entity view  
Voice Entity view  
Voice Entity view  
fax support-mode  
fax train-mode  
fdl  
Use the fax support-modecommand to configure the fax interworking mode with other equipments.  
Use the fax train-modecommand to configure the training mode used by the gateway.  
Use the fdlcommand to set the behavior of the CT1/PRI interface on the FDL in ESF framing.  
CT1/PRI Interface view  
E1-F Interface view  
E1-F Interface view  
fe1 clock  
Use the fe1 clockcommand to configure clocking on the E1-F interface.  
fe1 code  
Use the fe1 codecommand to configure the line code format of the E1-F interface.  
 
68  
3Com Router 5000/6000 Family  
Command Reference  
fe1 detect-ais (E1-F interface)  
fe1 frame-format  
Use the fe1 detect-aiscommand to enable alarm indication signal (AIS) detect on the E1-F interface.  
E1-F Interface view  
E1-F Interface view  
E1-F Interface view  
E1-F Interface view  
E1-F Interface view  
CT3 Interface view  
Use the fe1 frame-formatcommand to configure the framing format of the E1-F interface.  
fe1 loopback  
Use the fe1 loopbackcommand to place the E1-F interface in local or remote loopback.  
Use the fe1 timeslot-listcommand to bundle timeslots on the E1-F interface.  
fe1 timeslot-list  
fe1 unframed  
Use the fe1 unframedcommand to configure an E1-F interface to work in unframed mode.  
Use the feaccommand to enable FEAC channel signal detection and sending on the CT3 interface.  
Use the fifo queue-lengthcommand to set the FIFO queue length of frame relay virtual circuit.  
feac (CT3 Interface)  
fifo queue-length  
file prompt  
Frame Relay Class view  
Use the file promptcommand to enable or disable the router to warn when an operation may result in  
data loss or corruption.  
System view  
filename  
Use the filenamecommand to configure the name of the file to be gotten from or put onto an FTP server.  
HWPing Test Group view  
filter-policy  
Use the filter-policy exportcommand to configure the filtering conditions of the routing information  
advertised by a certain type of routing protocols.  
Routing Protocol view  
filter-policy export  
Use the filter-policy export command to filter the advertised routes and only the routes passing the  
filter can be advertised by BGP.  
BGP Unicast view  
BGP Multicast view  
VPNv4 view  
VPN Instance view  
filter-policy export  
filter-policy export  
Use the filter-policy exportcommand to configure IS-IS to filter all redistributed routes or routes  
redistributed from a specified routing protocol.  
IS-IS view  
Use the filter-policy exportcommand to configure OSPF to filter the LSAs of redistributed routes for  
advertisement.  
OSPF view  
RIP view  
filter-policy export  
Use the filter-policy exportcommand to configure to filter the advertised routing information by RIP.  
filter-policy gateway  
Use the filter-policy gateway import command to filter the routing information advertised by a  
specified router.  
Use the filter-policy import command to configure the condition for filtering the routing information.  
Routing Protocol view  
 
3Com Router 5000/6000 Family  
Command Reference  
69  
filter-policy import  
Use the filter-policy gateway importcommand to filter the learned routing information advertised by  
the specified address.  
Use the filter-policy import command to filter the received global routing information.  
BGP Unicast view  
BGP Multicast view  
VPNv4 view  
VPN Instance view  
filter-policy import  
filter-policy import  
Use the filter-policy importcommand to configure to filter the routes received by IS-IS.  
IS-IS view  
Use the filter-policy importcommand to configure the OSPF rules of filtering the routing information  
received.  
Use the filter-policy importcommand to filter the routes calculated by OSPF. Only the filtered routes  
can be added to the routing table. The filtering can be performed according to the next hop and destination  
of the route.  
OSPF view  
filter-policy import  
Use the filter-policy gatewaycommand to configure to filter the received routing information distributed  
from the specified address.  
Use the filter-policy importcommand to configure the filtering to the received global routing  
information.  
RIP view  
final-callednum  
Use the final-callednumcommand to enable or disable the terminate signal to be sent to the terminating  
point after the called number is sent.  
R2 CAS view  
Interface view  
firewall aspf  
Use the firewall aspfcommand to apply ASPF policy in specified direction to an interface.  
firewall default  
Use the firewall defaultcommand to configure the default filtering rule of the firewall, whether to be  
“permit” or “deny”.  
System view  
System view  
Interface view  
System view  
firewall enable  
Use the firewall enablecommand to enable the firewall.  
firewall ethernet-frame-filter  
Use the firewall ethernet-frame-filtercommand to apply a MAC-based ACL on the interface.  
firewall fragments-inspect  
Use the firewall fragments-inspectcommand to enable fragment inspection switch.  
firewall fragments-inspect {high | low}  
Use the firewall fragments-inspect { high | low }command to configure the high and low thresholds  
of records for fragment inspection.  
System view  
Interface view  
firewall packet-filter  
Use the firewall packet-filtercommand to apply the access control list to the corresponding interface.  
first-rule  
Use the first-rulecommand to configure the number-substitute rule that is first used in the current  
number-substitute list.  
Voice Number-Substitute view  
fixdisk  
Use the fixdiskcommand to restore the space of a storage device when it becomes unavailable because  
of some abnormal operation.  
User view  
 
70  
3Com Router 5000/6000 Family  
Command Reference  
flag  
Use the flagcommand to set the overhead byte of SONET/SDH frames.  
Use the flagcommand to set the SDH overhead byte.  
CPOS Interface view  
POS Interface view  
flag  
flow control  
Use the flow-controlcommand to enable flow control on the Ethernet interface, which is useful only when  
the peer end also supports flow control.  
Ethernet Interface view  
flow-control  
Use the flow-controlcommand to enable flow control on the Ethernet port to avoid packet drop when  
congestion occurs.  
Ethernet Port view  
User Interface view  
System view  
flow-control  
Use the flow-controlcommand to configure flow control mode.  
flow interval  
flow-interval  
flow-interval qos  
Use the flow-intervalcommand to configure traffic statistic interval.  
Use the flow-intervalcommand to configure the interval for measuring the average rate of the interfaces.  
System view  
Use the flow-interval qoscommand to configure QoS policy traffic statistical interval and QoS policy rate  
updating interval.  
System view  
GE Interface view  
R2 CAS view  
force-link  
force-metering  
format  
Use the force-linkcommand to enable the GE interface to work in force mode.  
Use the force-meteringcommand to enable or disable the metering signal of R2 signaling.  
Use the formatcommand to format a storage device.  
User view  
fqdn  
Use the fqdncommand to specify the FQDN of an entity.  
PKI Entity view  
fr bump  
Use the fr bumpcommand to configure the standby PVC that will take over when a specified PVC goes  
down.  
FR Pvc-Group view  
fr-class  
Use the fr-classcommand to associate a frame relay class with the current frame relay virtual circuit or  
frame relay interface.  
Frame Relay DLCI view  
fr class  
Use the fr classcommand to create a frame relay class and enter frame relay class view.  
Use the fr compression frf9command to enable the FRF9 compression function.  
Use the fr compression iphccommand to enable the IP header compression.  
System view  
fr compression frf9  
fr compression iphc  
Frame Relay Interface view  
Frame Relay Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
71  
fr congestion-threshold  
Use the fr congestion-thresholdcommand to enable congestion management function of a frame relay  
interface.  
Frame Relay Interface view  
MFR Interface view  
fr de del  
Use the fr de delcommand to apply a DE rule list to the specified frame relay virtual circuit.  
Frame Relay Interface (or Subinterface) view  
MFR Interface view  
fr del inbound-interface  
Use the fr del inbound-interfacecommand to configure an interface-based DE rule list. For the packet  
received from the specified interface, if it is forwarded from the router as a frame relay packet, its DE flag  
bit is set to 1 before being forwarded.  
System view  
System view  
fr del protocol ip  
Use the fr del protocol ipcommand to configure an IP-based DE rule list. The DE flag bit of the frame  
relay packet encapsulated with an IP packet matching the specified rule will be flagged as 1.  
fr dlci  
Use the fr dlcicommand to configure the virtual circuit for Frame Relay interface.  
Interface view  
PVC Group view  
fr dlci-switch  
Use the fr dlci-switchcommand to configure a static route for frame relay PVC switching.  
Frame Relay Interface view  
MFR Interface view  
fr inarp  
Use the fr inarpcommand to enable the inverse address resolution of Frame Relay.  
Use the fr interface-typecommand to set the Frame Relay interface type.  
Interface view  
Interface view  
fr interface-type  
fr ip-dscp  
Use the fr ip-dscpcommand to configure the PVC to carry packets of the specified priority levels when  
the DSCP identifier in the IP packet is used to identify the priority levels of packets.  
FR Pvc-Group view  
FR Pvc-Group view  
fr ip-precedence  
Use the fr ip-precedencecommand to configure the PVC to carry packets of the specified priority levels  
when the Precedence identifier in the IP packet is used to identify the priority levels of packets.  
fr iphc  
Use the fr iphccommand to enable IP header compression function, including RTP/TCP header  
compression.  
Frame Relay Interface view  
MFR Interface view  
fr lmi n391dte  
fr lmi n392dce  
fr lmi n392dte  
fr lmi n393dce  
fr lmi n393dte  
Use the fr lmi n391dtecommand to configure N391 parameter at the DTE side.  
Use the fr lmi n392dcecommand to set N392 parameter at the DCE side.  
Use the fr lmi n392dtecommand to set N392 parameter at the DTE side.  
Use the fr lmi n393dcecommand to set the N393 parameter at the DCE side.  
Interface view  
Interface view  
Interface view  
Interface view  
Interface view  
Use the fr lmi n393dtecommand to set N393 parameter at the DTE side.  
 
72  
3Com Router 5000/6000 Family  
Command Reference  
fr lmi t392dce  
fr lmi type  
fr map bridge  
fr map clns  
fr map ip  
Use the fr lmi t392dcecommand to set T392 parameter at the DCE side.  
Use the fr lmi typecommand to configure the Frame Relay LMI protocol type.  
Use the fr map bridgecommand to add a bridge-set to frame relay map entry.  
Use the fr map clns command to add an FR mapping for OSI packets.  
Use the fr map ipcommand to add an IP address map entry for FR.  
Use the fr map ipxcommand to add an IPX address map entry.  
Interface view  
Interface view  
Interface view  
Interface view  
Interface view  
Interface view  
fr map ipx  
fr map ppp interface virtual-template  
Use the fr map ppp interface virtual-templatecommand to map the FR DLCI (corresponds to an FR  
PVC) to a PPP link, so the PPPoFR link is established, and thus PPP packets can be sent/received on FR  
PVC.  
Interface view  
fr match  
Use the fr matchcommand to configure a PVC group to differentiate traffic by the Precedence or DSCP  
identifier in the TOS field of the IP header.  
FR Pvc-Group view  
fr mpls-exp  
Use the fr mpls-expcommand to configure the PVC to carry packets of the specified priority levels when  
the EXP identifier in the MPLS packet is used to identify the priority levels of packets.  
FR Pvc-Group view  
Interface view  
fr pvc-group  
fr pvc-pq  
Use the fr pvc-groupcommand to create a PVC group.  
Use the fr pvc-pqcommand to set the queue type of a frame relay interface as PVC PQ (PVC Priority  
Queuing) and set queue length, i.e. the maximum number of packets that can be held by a queue, for each  
queue.  
Frame Relay Interface view  
MFR Interface view  
fr pvc-protect  
fr switch  
Use the fr pvc-protectcommand to configure the protection mode for a PVC in a PVC group.  
FR Pvc-Group view  
Use the fr switchcommand to create a PVC used for frame relay switching and enter frame relay  
switching view.  
System view  
System view  
fr switching  
Use the fr switchingcommand to enable frame relay PVC switching.  
Use the fr traffic-policingcommand to enable FRTP function.  
fr traffic-policing  
Frame Relay Interface view  
MFR Interface view  
fr traffic-shaping  
Use the fr traffic-shapingcommand to enable FRTS function.  
Frame Relay Interface view  
MFR Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
73  
fragment  
Use the fragmentcommand to enable the FRF.12-compliant fragmentation function on frame relay virtual  
circuit.  
Frame Relay Class view  
frame-format  
frame-format  
frame-format  
frame-format  
frame-format  
Use the frame-formatcommand to set the frame format of ATM OC-3c/STM-1 interface.  
Use the frame-formatcommand to configure the ATM over E1/T1 framing format.  
Use the frame-formatcommand to configure frame format of ATM E3/T3 interface.  
Use the frame-formatcommand to set the frame type of the CPOS interface.  
Use the frame-formatcommand to set the frame format of the POS interface.  
ATM Interface view  
ATM E1/T1 Interface view  
ATM E3/T3 Interface view  
CPOS Interface view  
POS Interface view  
frame-format (CE1/PRI Interface)  
Use the frame-formatcommand to set the frame format on the CE1 interface.  
CE1/PRI Interface view  
CT1/PRI Interface view  
CT3 Interface view  
frame-format (CT1/PRI Interface)  
Use the frame-formatcommand to set the frame format on the CT1/PRI interface.  
frame-format (CT3 Interface)  
Use the frame-formatcommand to configure the frame format used by the CT3 interface.  
frame-length  
Use the frame-lengthcommand to configure the number of ATM cells in an IMA frame.  
IMA Group Interface view  
Synchronous Serial Interface view  
framefill none  
Use the framefill nonecommand to disable a serial interface to send interframe filling tags.  
Asynchronous Serial Interface view  
AUX Interface view  
AM Interface view  
free unused porttag  
free user-interface  
Use the free unused porttagcommand to release the port tag resources used by removed interfaces for  
creating new interfaces.  
System view  
Use the free user-interface numbercommand to disconnect the user corresponding to the user  
interface specified by its absolute index.  
User view  
frequency  
Use the frequencycommand to configure an automatic test interval.  
HWPing Test Group view  
ft1 alarm-threshold  
Use the alarm-thresholdcommand to configure the alarm thresholds on the T1-F interface as needed.  
T1-F Interface view  
T1-F Interface view  
T1-F Interface view  
ft1 bert (T1-F Interface)  
Use the ft1 bertcommand to start a BERT test on the T1-F interface.  
ft1 cable  
Use the ft1 cablecommand to configure attenuation or transmission segment matching the T1-F interface.  
 
74  
3Com Router 5000/6000 Family  
Command Reference  
ft1 clock  
Use the ft1 clockcommand to configure clocking on the T1-F interface.  
Use the ft1 codecommand to configure line code format for a T1-F interface.  
T1-F Interface view  
T1-F Interface view  
ft1 code  
ft1 data-coding  
Use the ft1 data-coding normalcommand to disable user data inversion on the T1-F interface.  
Use the ft1 data-coding invertedcommand to enable user data inversion on the CT1/PRI interface.  
T1-F Interface view  
T1-F Interface view  
T1-F Interface view  
T1-F Interface view  
T1-F Interface view  
ft1 fdl  
Use the ft1 fdlcommand to set the behavior of the T1-F interface on the FDL in ESF framing.  
Use the ft1 loopbackcommand to place the T1-F interface in local or remote loopback.  
Use the sendloopcodecommand to send remote loopback control code.  
ft1 loopback  
ft1 sendloopcode  
ft1 timeslot-list  
ft3 (CT3 Interface)  
Use the ft1 timeslot-listcommand to bundle timeslots on the T1-F interface.  
Use the ft3command to configure the CT3 interface to operate in FT3 mode and to set the DSU mode and  
subrate for FT3.  
CT3 Interface view  
User view  
ftp  
Use the ftpcommand to set up control connection to the remote FTP server and enter FTP client view.  
ftphost source-interface  
Use the ftphostsource-interfacecommand to specify the source interface that the FTP client uses  
when accessing the specified FTP server. This interface must be an exiting local interface.  
User view  
User view  
ftphost source-ip  
Use the ftphost source-ipcommand to specify the source IP address that the FTP client uses when  
accessing the specified FTP server.  
ftp-operation  
Use the ftp-operationcommand to configure the FTP operation done by the system.  
HWPing Test Group view  
System view  
ftp server enable  
Use the ftp server enablecommand to enable the FTP server to allow login of FTP users.  
ftp-server source-interface  
Use the ftp-server source-interfacecommand to specify a source interface, which must be an existing  
local interface, for the FTP server.  
System view  
System view  
System view  
System view  
ftp-server source-ip  
ftp source-interface  
ftp source-ip  
Use the ftp-server source-ipcommand to specify a source IP address for the packets sent by the FTP  
server. This IP address must be a local IP address.  
Use the ftp source-interfacecommand to specify a source interface, which must be an existing local  
interface, for the FTP client.  
Use the ftp source-ipcommand to specify a source IP address for the packets sent by the FTP client.  
This IP address must be a local IP address.  
 
3Com Router 5000/6000 Family  
Command Reference  
75  
ftp timeout  
Use the ftp timeoutcommand to set the idle-timeout timer.  
System view  
System view  
ftp update  
Use the ftp updatecommand to set the file update mode that the FTP server uses while receiving data.  
fxo-monitoring  
Use the fxo-monitoring enable command to enable the on line monitoring function on all FXO interfaces of  
the device.  
Voice view  
gateway-list  
Use the gateway-listcommand to configure IP addresses of the egress GW routers used by DHCP  
clients.  
DHCP Address Pool view  
get  
Use the getcommand to FTP a file from a remote server and save it.  
Use the getcommand to download and save a file from a remote server.  
FTP Client view  
get  
SFTP Client view  
gk-2nd-id  
Use the gk-2nd-idcommand to configure the name and IP address of the backup GK Server corresponding  
to the gateway.  
Use the gk-2nd-id command to configure the IP address, name and port of the backup GK Server.  
Use the gk-clientcommand to enter Voice GK client view, and configure the GK parameters for voice.  
Use the gk-idcommand to configure the GK Server name and IP address corresponding to the gateway.  
Voice GK Client view  
Voice view  
gk-client  
gk-id  
Use the command gk-id to configure such information as the IP address, name, and port of GK Server to  
facilitate the research for the right GK Server equipment by the GK Client according to this information, so  
as to implement the register task of gateway in the GK Server.  
Voice GK Client view  
gk-security call  
Use the gk-security call enablecommand to enable security calls on the GK Client (router).  
Voice GK Client view  
gk-security register-pwd  
Use the gk security register-pwdcommand to set the GK register password.  
Use the gk-security register-pwd command to remove the GK register password.  
Voice GK Client view  
System view  
gratuitous-arp-learning enable  
Use the gratuitous-arp-learning enablecommand to enable the address learning function of gratuitous  
ARP.  
gratuitous-arp-sending enable  
Use the gratuitous-arp-sending enablecommand to configure the system to return ARP responses  
when receiving gratuitous ARP packets from other network segments. The system, however, does not learn  
the received ARP entries.  
System view  
Tunnel Interface view  
Tunnel Interface view  
gre checksum  
Use the gre checksumcommand to configure the two ends of a tunnel to perform end-to-end check,  
verifying the correctness of packets and discard those that do not pass the verification.  
gre key  
Use the gre keycommand to set identification keyword of the tunnel interface, and by this feeble security  
mechanism avoid incorrectly identifying or receiving packets from undesired places.  
 
76  
3Com Router 5000/6000 Family  
Command Reference  
group  
Use the groupcommand to create a peer group.  
BGP view  
group-b  
Use the group-bcommand to enable or disable Group-B stage signal to complete register exchange.  
Use the gtscommand to configure traffic shaping for a behavior.  
R2 CAS view  
gts  
Traffic Behavior view  
gw-access-number  
Use the gw-access-numbercommand to configure the access service number or enter the view of the  
access service number.  
Voice Dial Program view  
Voice GK Client view  
gw-address  
gw-id  
Use the gw-addresscommand to configure the source IP address used by the voice gateway.  
Use the gw-idcommand to configure the gateway alias.  
Use the command gw-idto configure the gateway alias, which is used for the gateway to register and  
identify the voice gateway. Each gateway has only one alias, and the new alias will cover the old one.  
Voice GK Client view  
System view  
header  
help  
Use the headercommand to create a banner.  
Use the helpcommand to get the help information for the specified or all SFTP client commands.  
SFTP Client view  
User Interface view  
history-command max-size  
Use the history-command max-sizecommand to set the size of history command buffer.  
history keep-time  
history-record  
Use the history keep-timecommand to configure the retaining time of the history record for a test group.  
HWPing Test Group view  
HWPing Test Group view  
Use the history-record enablecommand to enable history record.  
history-records  
home-agent ip-address  
hookoff-time  
Use the history-recordscommand to configure the number of test results that the system can retain.  
HWPing Test Group view  
Use the home-agent ip-addresscommand to configure the HA address of the MR.  
MR view  
Use the hookoff-timecommand to configure the hangup timer. When this timer times out, the interface  
hangs up.  
FXO Voice Subscriber-Line view  
host-route  
hotkey  
Use the host-routecommand to control the RIP to accept the host route.  
Use the hotkeycommand to assign a hot key to a command line.  
Use the http-operationcommand to configure an HTTP operation type.  
RIP view  
System view  
http-operation  
HWPing Test Group view  
 
3Com Router 5000/6000 Family  
Command Reference  
77  
hwatacacs change-password self  
Use the hwtacacs change-password selfcommand to enable the TACACS online user to change the  
password.  
User view  
hwatacacs nas-ip  
hwatacacs scheme  
Use the hwtacacs nas-ipcommand to specify the source address of the hwtacacs packet sent from NAS.  
System view  
Use the hwtacacs schemecommand to enter TACACS+ Server view. If the specified TACACS+ server  
scheme does not exist, you can create a new TACACS+ scheme.  
System view  
System view  
System view  
System view  
System view  
System view  
System view  
System view  
IKE-Peer view  
hwping  
Use the hwpingcommand to create an HWPing test group.  
hwping-agent enable  
Use the hwping-agent enablecommand to enable the HWPing client function.  
hwping-agent max-requests  
Use the hwping-agent max-requestscommand to set the allowed maximum number of concurrent tests.  
hwping-server enable  
Use the hwping-server enablecommand to enable HWPing Server.  
hwping-server tcpconnect  
Use the hwping-server tcpconnectcommand to create a TCP listening service.  
hwping-server udpecho  
icmp redirect send  
id-type  
Use the hwping-server udpechocommand to create a UDP listening service.  
Use the icmp redirect sendcommand to enable the sending of ICMP Redirect messages.  
Use the id-typecommand to select the type of ID used in IKE negotiation.  
idle-mark  
Use the idle-markcommand to set the line idle-mark of the synchronous serial interface to “FF”.  
Synchronous Serial Interface view  
idle-timeout  
Use the idle-timeoutcommand to set the idle-timeout timer. When it expires, the user connection is  
disconnected.  
User Interface view  
idlecode (CE1/PRI Interface)  
Use the idlecodecommand to set the line idle code on the CE1/PRI interface. Two types of line idle code  
are available: 0x7e and 0xff.  
CE1/PRI Interface view  
idlecode (CT1/PRI Interface)  
Use the idlecodecommand to set the line idle code on the CT1/PRI interface. Two types of line idle code  
are available: 0x7e and 0xff.  
CT1/PRI Interface view  
if-match  
Use the if-matchcommand to define the match rule of a class.  
Use the if-match aclcommand to define ACL match rule.  
Class view  
Class view  
if-match acl  
if-match acl  
Use the if-match aclcommand to set conditions that multicast packets should meet in each policy node.  
Route-Policy view  
 
78  
3Com Router 5000/6000 Family  
Command Reference  
if-match acl  
Use the if-match aclcommand to set the match condition for IP address.  
Route-Policy view  
if-match acl  
Use the if-match aclcommand to configure the IP address range to match the route-policy.  
Use the if-match anycommand to define the rule matching all packets.  
Use the if-match as-pathcommand to filter BGP routing information.  
Routing Policy view  
Class view  
if-match any  
if-match as-path  
if-match atmclp  
Routing Policy view  
Use the if-match atmclpcommand to create a cell loss priority (CLP) bit match rule defining that ATM cells  
with CLP bit set to 1 are matched.  
Use the if-match not atmclpcommand to create a CLP bit match rule defining that ATM cells with CLP  
bit set to 0 are matched.  
Class view  
Class view  
if-match classifier  
if-match community  
Use the if-match classifiercommand to define class-map match rule.  
Use the if-match communitycommand to configure the community list number to be matched in  
route-policy.  
Routing Policy view  
Routing Policy view  
if-match cost  
Use the if-match costcommand to configure one of the matching rules of route-policy to match the cost  
of the routing information.  
if-match {destination-mac | source-mac}  
Use the if-match{ destination-mac | source-mac } command to define match rule of destination or source  
MAC address.  
Class view  
Class view  
if-match dot1p-cos  
if-match dscp  
Use the if-match dot1p-coscommand to define a COS field match rule for VLAN packets.  
Use the if-match dscpcommand to define an IP DSCP match rule.  
Use the if-match fr-decommand to define an FR DE matching rule.  
Class view  
if-match fr-de  
Class view  
if-match inbound-interface  
Use the if-match inbound-interfacecommand to define ingress interface match rule of a class.  
Class view  
if-match interface  
Use the if-match interfacecommand to match the route whose next hop is designated interface.  
Routing Policy view  
if-match ip next-hop  
Use the if-match ip next-hopcommand to configure one of the match rules of route-policy on the next  
hop address of the routing information.  
Routing Policy view  
Class view  
if-match ip-precedence  
Use the if-match ip-precedencecommand to define IP precedence match rule.  
if-match ip-prefix  
Use the if-match ip-prefixcommand to configure one of the match rules of route-policy on the IP  
address range of the routing information.  
Routing Policy view  
 
3Com Router 5000/6000 Family  
Command Reference  
79  
if-match mpls-exp  
Use the if-match mpls-expcommand to configure the matching rule for EXP domain of MPLS.  
Class view  
if-match mpls-label  
Use the if-match mpls-label command to configure to match public network routes with MPLS labels  
only.  
Route-Policy view  
if-match outbound-interface  
Use the if-match outbound-subinterfacecommand to define an outbound subinterface matching rule for  
the class.  
Class view  
Route-Policy view  
Class view  
if-match packet length  
Use the if-match packet-lengthcommand to set length match conditions of IP packets.  
Use the if-match protocolcommand to define protocol matching rules.  
Use the if-match protocol rtpcommand to configure RTP matching rules.  
Use the if-match rtpcommand to define port match rule of RTP.  
if-match protocol  
if-match protocol rtp  
if-match rtp  
Class view  
Class view  
if-match tag  
Use the if-match tagcommand to match the tag field of OSPF route information.  
Use the igmp enablecommand to enable IGMP on an interface.  
Routing Policy view  
Interface view  
igmp enable  
igmp group-limit  
Use the igmp group-limit command to limit the number of IGMP groups joined on the interface. If the  
number exceeds the limit, the router will not process the joined IGMP packet any more.  
Interface view  
igmp group-policy  
igmp host-join  
Use the igmp group-policycommand to set the filter of multicast groups on an interface to control the  
accessing to the IP multicast groups.  
Interface view  
Interface view  
Use the igmp host-joincommand to enable an interface of a router to join a multicast group.  
igmp lastmember-queryinterval  
Use the igmp lastmember-queryinterval command to set the interval at which IGMP querier sends the  
IGMP specified group query packet when it receives IGMP Leave packet from the host.  
Interface view  
Interface view  
Interface view  
Interface view  
igmp max-response-time  
Use the igmp max-response-timecommand to configure the maximum response time contained in the  
IGMP query packet.  
igmp proxy  
Use the igmp proxycommand to specify an interface of a leaf network router as the IGMP proxy of another  
interface.  
igmp robust-count  
Use the igmp robust-countcommand to set the times IGMP querier sends the IGMP specified group query  
packet when it receives IGMP Leave packet from the host.  
 
80  
3Com Router 5000/6000 Family  
Command Reference  
igmp timer other-querier-present  
Use the igmp timer other-querier-presentcommand to configure the overtime value of presence of  
IGMP querier.  
Interface view  
igmp timer query  
Use the igmp timer query command to configure the interval at which a router interface sends IGMP query  
messages.  
Interface view  
Interface view  
igmp version  
Use the igmp versioncommand to specify the version of IGMP that a router uses.  
ignore-lsp-checksum-error  
Use the ignore-lsp-checksum-error command to configure the IS-IS to ignore the checksum error of  
LSP.  
IS-IS view  
System view  
System view  
ike dpd  
Use the ike dpdcommand to create a DPD structure and enter its view.  
Use the ike local-namecommand to set the name of the local GW.  
ike local-name  
ike next-payload check disabled  
Use the ike next-payload check disabledcommand to disable the router to check the next-payload field  
in the last payload of the IKE negotiation packet during IPSec negotiation for compatibility with other  
vendors.  
System view  
ike peer (IPSec Policy view or IPSec Policy Template view)  
Use the ike peercommand to quote an IKE peer in an IPSec policy or IPSec policy template.  
IPSec Policy view  
IPSec Policy Template view  
ike peer (System view)  
Use the ike peercommand to configure an IKE peer and access IKE-peer view.  
System view  
System view  
ike proposal  
Use the ike proposalcommand to define an IKE proposal.  
ike sa keepalive-timer interval  
Use the ike sa keepalive-timer interval command to configure the interval for sending Keepalive  
packet to the remote end through ISAKMP SA.  
System view  
System view  
System view  
ike sa keepalive-timer timeout  
Use the ike sa keepalive-timer timeoutcommand to configure a timeout for ISAKMP SA to wait for the  
Keepalive packet.  
ike sa nat-keepalive-timer interval  
Use the ike sa nat-keepalive-timer intervalcommand to configure the NAT keepalive interval for IKE  
peers.  
ima-clock  
Use the ima-clockcommand to configure the clock mode of the IMA group.  
IMA Group Interface view  
ima ima-group  
Use the ima ima-groupcommand to add the ATM E1/T1 interface to the specified IMA group. If the  
specified IMA group does not exist, it is created first.  
ATM E1/T1 Interface view  
ima-test  
Use the ima-testcommand to set a test pattern for testing the connectivity of the specified link to the rest  
of the IMA group.  
IMA Group Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
81  
impedance  
Use the impedancecommand to configure the current electric impedance on a voice subscriber-line.  
FXO Voice Subscriber-Line view  
import-route  
Use the import-routecommand to redistribute routes from other protocols.  
BGP view  
import-route  
import-route  
import-route  
import-route  
import-route isis  
Use the import-routecommand to import routing information from other protocols to BGP.  
IPv4 Multicast Subaddress Family view  
Use the import-routecommand to configure IS-IS to filter the redistributed routes.  
IS-IS view  
Use the import-routecommand to redistribute the information of another routing protocol.  
Use the import-routecommand to redistribute the routes of other protocols into RIP.  
OSPF view  
RIP view  
Use the import-route isis level-2 into level-1command to enable routing information in a Level-2  
area to be redistributed to a Level-1 area.  
IS-IS view  
import-route ospf  
import-source  
Use the import-route ospfcommand to enable to import OSPF route.  
BGP Unicast/Multicast view  
MBGP VPN-Instance Address Family view  
Use the import-sourcecommand to configure which (S, G) entries in the domain need to be advertised  
when a MSDP originates an SA message.  
MSDP view  
System view  
info-center channel  
Use the info-center channelcommand to assign a name to the information channel specified by  
channel-number.  
info-center console channel  
Use the info-center console channel command to have the info-center output information to the console  
over the specified channel.  
System view  
System view  
info-center enable  
Use the info-center enablecommand to enable the info-center.  
info-center logbuffer  
Use the info-center logbuffercommand to enable the log buffer and specify the channel for system  
information output as well as the size of the log buffer.  
System view  
info-center logfile  
info-center loghost  
Use the info-center logfile channelcommand to have the info-center output system information to the  
log file.  
System view  
System view  
Use the info-center loghostcommand to have the info-center output information to the log host.  
info-center loghost source  
Use the info-center loghost sourcecommand to specify the source address in the packets destined to  
the log host.  
System view  
 
82  
3Com Router 5000/6000 Family  
Command Reference  
info-center monitor channel  
Use the info-center monitor channel command to have the info-center output information over the  
specified channel to the user terminal.  
System view  
System view  
System view  
System view  
info-center snmp channel  
Use the info-center snmp channelcommand to set the information channel for SNMP.  
Use the info-center sourcecommand to add records to an information channel.  
info-center source  
info-center synchronous  
Use the info-center synchronouscommand to enable synchronous terminal output.  
info-center timestamp  
Use the info-center timestampcommand to set a time stamp format for the system information output to  
the information channels except for the log host.  
System view  
System view  
info-center timestamp loghost  
Use the info-center timestamp loghostcommand to set a time stamp format for the system information  
output to the log host.  
info-center trapbuffer  
Use the info-center trapbuffercommand to enable the trap buffer, set its size and the channel that  
outputs information to it.  
System view  
System view  
interface  
interface  
Use the interfacecommand to create a P2MP or P2P subinterface.  
Use the interfacecommand to enter the specified interface view or create a logical interface or  
subinterface.  
System view  
System view  
System view  
interface  
Use the interfacecommand to enter Ethernet port view.  
interface atm  
Use the interface atmcommand to enter the view of the specified ATM E1/T1 interface.  
interface bridge-template  
Use the interface bridge-templatecommand to create a bridge template interface, connecting the  
specified bridge set to the routing network.  
System view  
interface dialer  
Use the interface dialercommand to create a dialer circular group for the Circular DCC, or configure a  
dialer interface for the Resource-Shared DCC.  
System view  
System view  
System view  
System view  
System view  
interface encrypt  
interface ethernet  
interface ima  
Use the interface encryptcommand to enter encryption card interface view.  
Use the interface ethernetcommand to create an Ethernet subinterface.  
Use the interface imacommand to enter the specified IMA group interface view.  
interface logic-channel  
Use the interface logic-channelcommand to create a logical channel interface.  
 
3Com Router 5000/6000 Family  
Command Reference  
83  
interface loopback  
Use the interface loopbackcommand to create a loopback interface or its view.  
System view  
interface mfr  
Use the interface mfrcommand to create a multilink frame relay bundle interface or sub-interface and  
enter the corresponding interface view.  
System view  
System view  
System view  
interface mp-group  
interface null  
Use the interface mp-groupwcommand to create an MP-group interface.  
Use the interface nullcommand to enter null interface view.  
interface serial [ p2p | p2mp ]  
Use the interface serial[ p2p | p2mp ]command to configure type of the specified FR subinterface  
and enter frame relay subinterface view.  
System view  
System view  
System view  
interface tunnel  
Use the interface tunnelcommand to create a tunnel interface and enter the view of this tunnel interface.  
interface virtual-ethernet  
Use the interface virtual-ethernetcommand to create a virtual Ethernet interface.  
interface virtual-template  
Use the interface virtual-templatecommand to create a virtual template or enter the existing virtual  
template view.  
System view  
interval-time  
Use the interval-timecommand to configure the interval for triggering DPD query.  
DPD Structure view  
invert receive-clock  
Use the invert receive-clockcommand to invert the receive-clock signal on the DTE-side synchronous  
serial interface.  
Serial Interface View  
invert transmit-clock  
Use the invert transmit-clockcommand to enable the inverting of the transmit-clock signal of the  
synchronous serial interface at the DTE side.  
Serial Interface view  
PKI Entity view  
HA-MR view  
ip  
Use the ipcommand to specify the IP address of an entity.  
ip address  
ip address  
ip address  
Use the ip addresscommand to configure the home address of an MR.  
Use the ip addresscommand to set an IP address for an interface.  
Use the ip addresscommand to configure the home address of an MR.  
Interface view  
MR view  
ip address bootp-alloc  
Use the ip address bootp-alloccommand to configure the Ethernet interface to obtain IP address using  
BOOTP.  
Ethernet Interface view  
ip address dhcp-alloc  
Use the ip address dhcp-alloccommand to enable DHCP client on the Ethernet or WAN interface for  
obtaining local IP address.  
Interface view (Ethernet Interface or Subinterface)  
Synchronous/Asynchronous Serial Interface (encapsulated with PPP, HDLC, or frame relay, E1 interface)  
 
84  
3Com Router 5000/6000 Family  
Command Reference  
ip address ppp-negotiate  
Use the ip address ppp-negotiatecommand to allow IP address be assigned through negotiation at the  
interface.  
Interface view  
ip address unnumbered  
Use the ip address unnumberedcommand to enable an interface to borrow the IP address of another  
interface.  
Interface view  
System view  
ip as-path-acl  
Use the ip as-path-aclcommand to configure an AS path regular expression.  
ip binding vpn-instance  
ip community-list  
Use the ip binding vpn-instance command to bind an interface or subinterface to a vpn-instance.  
Interface (or Subinterface) view  
Use the ip community-listcommand to configure a BGP community list.  
System view  
ip count enable  
Use the ip count enablecommand to enable IP accounting.  
System view  
ip count exterior threshold  
Use the ip count exterior-thresholdcommand to configure maximum number of entries in the exterior  
hash table, with each entry for an IP packet that does not match any IP accounting rule.  
System view  
Interface view  
Interface view  
System view  
ip count firewall denied  
Use the ip count firewall-deniedcommand to configure the IP Accounting to count the IP packets  
denied by the firewall on the current interface.  
ip count inbound packets  
Use the ip count inbound-packetscommand to configure the IP Accounting to count inbound IP packets  
on the current interface.  
ip count interior threshold  
Use the ip count interior-thresholdcommand to configure maximum number of entries in the interior  
hash table, with each entry for an IP packet matching the IP accounting rule.  
ip count outbound-packets  
Use the ip count outbound-packetscommand to configure the IP Accounting to count outbound IP  
packets on the current interface.  
Interface view  
System view  
System view  
System view  
ip count rule  
ip count timeout  
ip df-check enable  
ip-dscp  
Use the ip count rulecommand to configure IP accounting rules.  
Use the ip count timeoutcommand to configure the aging time of IP accounting entries.  
Use the ip df-check enablecommand to enable don’t fragment bit (DF-bit) check for IP packets.  
Use the ip-dscpcommand to configure the PVC to carry packets of the specified priority levels when the  
DSCP identifier in the IP packet is used to identify the priority levels of packets.  
ATM Pvc-Group view  
 
3Com Router 5000/6000 Family  
Command Reference  
85  
ip fast-forwarding  
Use the ip fast-forwardingcommand to enable unicast fast packet forwarding on both inbound and  
outbound interfaces.  
Use the ip fast-forwardinginbound command to enable unicast fast packet forwarding on the inbound  
interface.  
Use the ip fast-forwardingoutbound command to enable unicast fast packet forwarding on the outbound  
interface.  
Interface view  
Interface view  
System view  
System view  
System view  
Interface view  
ip forward-broadcast  
Use the ip forward-broadcastcommand to enable the current interface to forward broadcasts.  
Use the ip hostcommand to configure the IP address corresponding to a host name.  
Use the ip ip-prefixcommand to configure an address prefix list or one of its items.  
ip host  
ip ip-prefix  
ip local policy route-policy  
Use the ip local policy route-policycommand to enable local policy routing.  
ip multicast-fast-forwarding  
Use the ip multicast-fast-forwardingcommand to enable multicast fast forwarding on an interface.  
ip multicast-policy route-policy  
Use the ip multicast-policy route-policycommand to enable a multicast policy routing on an  
interface.  
Interface view  
System view  
ip netstream aggregation  
Use the ip netstream aggregationcommand to enter NetStream aggregation view.  
ip netstream export host  
Use the ip netstream export hostcommand to set the destination IP address and UDP port number for  
NetStream UDP packets.  
System view,  
NetStream Aggregation view  
ip netstream export source  
Use the ip netstream export sourcecommand to configure a source interface for NetStream UDP  
packets.  
System view,  
NetStream Aggregation view  
ip netstream export version  
Use the ip netstream export versioncommand to configure the type of AS numbers to be recorded in  
NetStream cache entries and the version of UDP packets.  
System view  
System view  
ip netstream format no-direction  
Use the ip netstream format no-directioncommand to remove flow direction mark in the header of  
NetStream log packet.  
ip netstream { inbound | outbound }  
Use the ip netstream{ inbound | outbound } command to enable NetStream statistics in the inbound  
or outbound direction of the interface.  
Interface view  
System view  
System view  
ip netstream max-entry  
Use the ip netstream max-entrycommand to set the NetStream cache size.  
ip netstream timeout active  
Use the ip netstream timeout activecommand to set the active aging timer for NetStream cache entries.  
 
86  
3Com Router 5000/6000 Family  
Command Reference  
ip netstream timeout inactive  
Use the ip netstream timeout inactivecommand to set the inactive aging timer for NetStream cache  
entries.  
System view  
ip option source-routing  
Use the ip option source-routingcommand to enable IP source routing, allowing the router to handle  
the packets with the IP source-route option.  
System view  
Interface view  
ip policy route-policy  
Use the ip policy route-policycommand to enable policy routing at an interface.  
ip pool  
Use the ip poolcommand to configure a local address pool for assigning addresses to PPP users.  
System view  
ISP Domain view  
ip-precedence  
Use the ip-precedencecommand to set the precedence of IP packets carried over PVC.  
ATM PVC-Group view  
ip relay address cycle  
Use the ip relay address cyclecommand to enable the DHCP relay to allocate servers using the load  
sharing approach, where the HASH algorithm applies allowing different clients to use different DHCP  
servers and the same client to use the same DHCP server so long as it is possible.  
System view  
ip relay address (Interface view)  
Use the ip relay address command to specify the exact location of a DHCP server by configuring an IP  
relay address for it on the current interface.  
Interface view  
System view  
ip relay address interface (System view)  
Use the ip relay address interfacecommand to configure a relay address for the Ethernet interfaces  
in a specified range for the purpose of transparent forwarding.  
ip route-static  
Use the ip route-staticcommand to configure a static route.  
Use the ip route-static vpn-instancecommand to configure a static route. In the application of  
multi-role host, you can configure a static route on a private network to specify the interface of another  
private network or public network as its outbound interface.  
System view  
System view  
ip route-static detect-group  
Use the ip route-static detect-groupcommand to configure a static route and reference a detect group.  
ip route-static vpn-instance  
Use the ip route-static vpn-instancecommand to configure a static route, by specifying a private  
network interface as the outgoing-interface of this static route.  
System view  
ip rpf-longest-match  
ip rpf-route-static  
Use the ip rpf-longest-matchcommand to configure the longest-match rule to be the multicast RPF route  
selecting policy.  
System view  
System view  
System view  
Interface view  
Interface view  
Use the ip rpf-route-staticcommand to configure multicast static routes.  
ip source-address-check  
Use the ip source-address-checkcommand to enable source address check function for IP packets.  
ip tcp vjcompress  
Use the ip tcp vjcompresscommand to enable a PPP interface to compress the VJ TCP header.  
ip urpf  
Use the ip urpfcommand to enable URPF check on the interface.  
 
3Com Router 5000/6000 Family  
Command Reference  
87  
ip vpn-instance  
Use the ip vpn-instancecommand to create and configure a vpn-instance.  
Use the ip vpn-instancecommand to create a vpn-instance named vpn-name.  
System view  
Routing Protocol (BGP and RIP) view  
ipsec card-proposal  
Use the ipsec card-proposalcommand to create an SA proposal for the encryption card and enter the  
corresponding view.  
System view  
ipsec policy (Interface view)  
Use the ipsec policy(Interface view) command to apply an ipsec policy group with the name  
policy-nameat the interface,.  
Interface view  
System view  
ipsec policy (System view)  
Use the ipsec policycommand to establish or modify an ipsec policy, and enter IPSec policy view.  
ipsec policy-template  
Use the ipsec policy-templatecommand to establish or modify an IPSec policy template, and enter  
IPSec policy template view.  
System view  
ipsec proposal  
Use the ipsec proposalproposal-namecommand to establish or modify a proposal named  
proposal-name, and enter IPSec proposal view.  
System view  
System view  
ipsec sa global-duration  
Use the ipsec sa global-durationcommand to set a global SA duration.  
ipv4-family  
Use the ipv4-familycommand to enter IPv4 extended address family view of BGP.  
Use the ipv4-family multicastcommand to multicast. For relevant contents, refer to "MBGP Multicast  
Extended" chapter in module "Multicast" of this manual.  
Use the ipv4-family vpn-instancecommand for BGP/MPLS VPN. For related description, refer to "MPLS  
VPN" chapter in module "MPLS" module of this manual.  
BGP view  
VPN Instance view  
ipv4-family  
Use the ipv4-family multicastcommand to enter MBGP multicast address family view.  
Use the ipv4-family vpn-instancecommand to enter MBGP vpn-instance address family view.  
Use the ipv4-family vpnv4command to enter MBGP VPNv4 address family view.  
BGP view  
BGP view  
RIP view  
BGP view  
ipv4-family multicast  
Use the ipv4-family multicastcommand to enter the IPv4 multicast subaddress family view.  
ipv4-family vpn-instance  
Use the ipv4-familycommand to enter MBGP address family view of RIP.  
ipv4-family vpnv4  
idle-mark  
Use the ipv4-family vpnv4command to enter VPNv4 address family view of BGP.  
Use the idle-markcommand to configure the idle coding scheme of the synchronous serial port.  
Synchronous Serial Interface view  
ipx enable  
Use the ipx enablecommand to activate IPX.  
System view  
ipx encapsulation  
Use the ipx encapsulationcommand to set IPX frame encapsulation format on Ethernet interface.  
Ethernet Interface view  
 
88  
3Com Router 5000/6000 Family  
Command Reference  
ipx netbios-propagation  
Use the ipx netbios-propagationcommand to configure the router to forward type 20 broadcast packets  
on the current interface.  
Interface view  
Interface view  
ipx network  
Use the ipx networkcommand to configure a network ID for an interface.  
ipx rip import-route  
Use the ipx rip import-route staticcommand to import static routes into RIP. RIP adds them in their  
route updates.  
System view  
Interface view  
System view  
System view  
ipx rip mtu  
Use the ipx rip mtucommand to configure RIP updating packet size.  
ipx rip multiplier  
ipx rip timer update  
Use the ipx rip multipliercommand to configure the aging period of RIP routing information table items.  
Use the ipx rip timer updatecommand to configure RIP updating interval.  
ipx route load-balance-path  
Use the ipx route load-balance-pathcommand to configure the equivalent route number to the same  
destination address.  
System view  
ipx route max-reserve-path  
Use the ipx route max-reserve-pathcommand to configure the maximum dynamic route number to the  
same destination address.  
System view  
System view  
Interface view  
Interface view  
ipx route-static  
ipx sap disable  
Use the ipx route-staticcommand to configure IPX static route.  
Use the ipx sap disablecommand to disable SAP on the current interface.  
ipx sap gns-disable-reply  
Use the ipx sap gns-disable-replycommand to disable IPX GNS reply on the current interface.  
ipx sap gns-load-balance  
Use the ipx sap gns-load-balancecommand to configure the router to respond GNS request in  
Round-robin method, that is, all servers respond GNS request in turn.  
System view  
ipx sap max-reserve-servers  
Use the ipx sap max-reserve-servers command to configure the length of the service information  
reserve queue.  
System view  
Interface view  
ipx sap mtu  
Use the ipx sap mtucommand to configure the maximum size of SAP updating packet.  
ipx sap multiplier  
Use the ipx sap multiplier command to configure the aging period of SAP service information table  
items.  
System view  
System view  
System view  
ipx sap timer update  
Use the ipx sap timer updatecommand to configure SAP updating interval.  
Use the ipx service commandto add a static service information item to SIT.  
 
ipx service  
3Com Router 5000/6000 Family  
Command Reference  
89  
ipx split-horizon  
Use the ipx split-horizoncommand to enable split horizon on the current interface.  
Interface view  
Interface view  
ipx tick  
Use the ipx tick command to configure the delay of interface sending IPX packets.  
ipx update-change-only  
Use the ipx update-change-onlycommand to enable trigger update on the current interface.  
Interface view  
is-level  
Use the is-levelcommand to configure the IS-IS level.  
IS-IS view  
isdn bch-local-manage  
isdn bch-select-way  
isdn caller-number  
isdn calling  
Use the isdn bch-local-managecommand to enable local ISDN B channel management.  
Use the isdn bch-select-way command to set a B channel selection method.  
Use the isdn caller-numbercommand to configure the range of the numbers that the router can receive.  
ISDN Interface view  
ISDN Interface view  
ISDN Interface view  
Use the isdn callingcommand to have the messages from a calling party to a called party carry the calling  
number.  
ISDN Interface view  
isdn check-called-number  
Use the isdn check-called-numbercommand to configure the called number or subaddress that the  
system should verify when receiving a digital call.  
ISDN BRI Interface view  
ISDN PRI Interface view  
isdn crlength  
Use the isdn crlengthcommand to set length of the call reference used when a call is placed on an ISDN  
interface.  
ISDN Interface view  
isdn ie passthrough  
Use the isdn ie passthroughcommand to enable transparent transmission of some or all related  
information elements and you can use this command to configure transparent transmission direction.  
ISDN Interface view (not applicable on BRI Interface)  
isdn ignore connect-ack  
Use the isdn ignore connect-ackcommand to configure the router to switch the ISDN protocol state to  
ACTIVE to start the data and voice service communications after sending a CONNECT message without  
having to wait for a CONNECT ACK message.  
ISDN Interface view  
ISDN Interface view  
ISDN Interface view  
isdn ignore hlc  
isdn ignore llc  
Use the isdn ignore hlccommand to disable ISDN to carry the higher layer compatibility (HLC)  
information element in the SETUP messages sent when placing voice calls.  
Use the isdn ignore llccommand to disable ISDN to carry the Lower Layer Compatibility (LLC)  
information element in the SETUP messages sent when placing voice calls.  
isdn ignore sending-complete  
Use the isdn ignore sending-completecommand to configure the ISDN protocol to ignore the processing  
on the Sending Complete Information Element.  
ISDN Interface view  
ISDN Interface view  
isdn L3-timer  
Use the isdn L3-timercommand to configure the duration of an ISDN L3 timer.  
 
90  
3Com Router 5000/6000 Family  
Command Reference  
isdn number-property  
Use the isdn number-propertycommand to set the type and code scheme of calling or called numbers in  
incoming or outgoing ISDN calls.  
ISDN Interface view  
isdn overlap-sending  
Use the isdn overlap-sendingcommand to set the system to send the called number information in the  
overlap mode on the ISDN interface.  
ISDN Interface view  
ISDN Interface View  
Interface view  
isdn q921-permanent  
isdn pri-slipwnd-size  
isdn protocol-mode  
Use the isdn q921-permanentcommand to enable the Q.921 permanent link function.  
Use the isdn pri-slipwnd-sizecommand to set the slide window size on a PRI interface.  
Use the isdn protocol-modecommand to set the ISDN interface to operate on the user side or network  
side of ISDN protocol.  
ISDN Interface view  
ISDN Interface view  
isdn protocol-type  
isdn send-restart  
Use the isdn protocol-typecommand to set the ISDN protocol to be run on an ISDN interface.  
Use the isdn send-restartcommand to enable PRI interfaces to actively send ISDN RESTART  
messages to clear calls of the remote end before maintaining B channels.  
System view  
ISDN BRI Interface view  
ISDN BRI Interface view  
ISDN BRI Interface view  
ISDN BRI Interface view  
isdn spid auto_trigger  
Use the isdn spid auto_triggercommand to enable SPID auto-negotiation once on the BRI interface  
running the NI protocol.  
isdn spid nit  
isdn spid resend  
isdn spid service  
isdn spid timer  
isdn spid1  
Use the isdn spid nitcommand to set the SPID processing mode to NIT (Not Initial Terminal) on an  
NI-compliant BRI interface.  
Use the isdn spid resendcommand to set the number of INFORMATION message retransmission  
attempts for SPID negotiation or initialization on an NI-compliant BRI interface.  
Use the isdn spid servicecommand to configure the service types that must be supported in SPI  
negotiation on the BRI interface adopting NI protocol.  
Use the isdn spid timercommand to set the duration of the timer TSPID for an NI-compliant BRI interface  
to timer_length.  
ISDN BRI Interface view  
Use the isdn spid1command to configure SPID information for the B1 channel on the NI-compliant BRI  
interface.  
ISDN BRI Interface view  
isdn spid2  
Use the isdn spid2command to configure SPID information for the B1 channel on an NI-compliant BRI  
interface.  
ISDN BRI Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
91  
isdn statistics  
Use the isdn statisticscommand to have the system make statistics on the information received and  
transmitted at an ISDN interface.  
Use the isdn statistics startcommand in the view of an interface to start making statistics on the  
messages received and transmitted at the interface.  
Use the isdn statistics displaycommand to view the statistic information.  
Use the isdn statistics continuecommand to continue the effort in making statistics.  
Use the isdn statistics display flowcommand to view the statistics in the form of flow.  
Use the isdn statistics stopcommand to stop making statistics.  
ISDN Interface view  
isdn two-tei  
Use the isdn two-teicommand to have the router requests the connected switch for a new TEI value  
before calling for a B channel.  
BRI Interface view  
System view  
isis  
Use the isiscommand to enable the corresponding IS-IS routing process and enter the IS-IS view.  
isis authentication-mode  
Use the isis authentication-modecommand to configure the IS-IS to authenticate the hello messages  
of the corresponding level, in the specified mode and with the specified password on the IS-IS interface.  
Interface view  
Interface view  
Interface view  
isis circuit-level  
isis cost  
Use the isis circuit-levelcommand to configure the link adjacency relationship.  
Use the isis costcommand to configure the link cost of this interface when performing SPF calculation.  
isis dis-priority  
Use the isis dis-prioritycommand to configure the priority of an interface for the corresponding level  
DIS election.  
Interface view  
isis enable  
Use the isis enablecommand to configure this interface to activate the corresponding IS-IS routing  
process.  
Interface view  
Interface view  
Interface view  
isis enable clns  
isis mesh-group  
isis small-hello  
Use the isis enable clnscommand to enable CLNS-based IS-IS routing process for a specified interface.  
Use the isis mesh-groupcommand to add an interface to a specified mesh group.  
Use the isis small-hellocommand to disable IS-IS to stuff Hello packets to the size of interface MTU if  
their data sizes are smaller.  
Interface view  
Interface view  
Interface view  
Interface view  
isis timer csnp  
Use the isis timer csnp command to configure the interval of sending CSNP packets on the broadcast  
network.  
isis timer hello  
Use the isis timer hellocommand to configure the interval of sending hello message of corresponding  
level.  
isis timer holding-multiplier  
Use the isis timer holding-multiplier command to configure the number of invalid Hello messages  
for the interface.  
 
92  
3Com Router 5000/6000 Family  
Command Reference  
isis timer lsp  
Use the isis timer lspcommand to configure minimum IS-IS LSP interval on the interface.  
Interface view  
Interface view  
isis timer retransmit  
Use the isis timer retransmitcommand to configure the LSP retransmission interval over the  
point-to-point link.  
itf (CE1/PRI Interface)  
Use the itfcommand to set the type of and the number of interframe filling tags on the CE1/PRI interface.  
Two types of interframe filling tag are available: 0x7e and 0xff.  
CE1/PRI Interface view  
itf (CT1/PRI Interface)  
Use the itfcommand to set the type of and the the number of interframe filling tags on the CT1/PRI  
interface. Two types of interframe filling tag are available: 0x7e and 0xff.  
CT1/PRI Interface view  
HWPing Test Group view  
HWPing Test Group view  
jitter-interval  
jitter-packetnum  
keepalive  
Use the jitter-intervalcommand to set a packet sending interval for a jitter test.  
Use the jitter-packetnumcommand to configure the number of packets to be sent in a jitter test.  
Use the keepalivecommand to enable the keepalive function of GRE and configure the interval for sending  
keepalive messages and the maximum number of sending attempts as well.  
Tunnel Interface view  
language-mode  
Use the language-modecommand to toggle the display language of the command line interface (CLI)  
between English and Chinese.  
User view  
Interface view  
Interface view  
lapb max-frame  
lapd modulo  
Use the lapb max-framecommand to configure LAPB parameter N1.  
Use the lapb modulocommand to specify the LAPB frame numbering view (also called modulo).  
lapb pollremote  
Use the lapb pollremotecommand to configure the link protocol to teardown the link in use after receiving  
false packets.  
Interface view  
Interface view  
Interface view  
lapb retry  
Use the lapb retrycommand to configure LAPB parameter N2.  
lapd timer  
Use the lapb timercommand to configure the LAPB timers T1, T2 and T3.  
lapb window-size  
Use the lapb window-sizecommand to configure the LAPB window  
parameter K.  
Interface view  
PKI Domain view  
FTP Client view  
Local User view  
ldap-server  
Use the ldap-server ipcommand to configure the LDAP server IP address and the port.  
Use the lcdcommand to get the local working directory path of the FTP client.  
Use the levelcommand to configure user priority level.  
lcd  
level  
 
3Com Router 5000/6000 Family  
Command Reference  
93  
limit  
Use the limitcommand to create rule under corresponding connection limit policy.  
Connection Limit Policy view  
POTS Voice Entity view  
line  
line  
Use the linecommand to associate the voice entity with a specified voice subscriber-line.  
Use the linecommand to configure the corresponding relationship between the POTS voice entity and the  
logic subscriber line.  
POTS Voice Entity view  
link-protocol  
Use the link-protocolcommand to set the link layer protocol of the interface.  
POS Interface view  
Interface view  
link-protocol fr  
link-protocol fr mfr  
Use the link-protocol frcommand to encapsulate interface link layer protocol as Frame Relay.  
Use the link-protocol fr mfrcommand to configure the current physical interface as an MFR bundle link  
and bundle it onto a specified MFR interface.  
Interface view  
Interface view  
Interface view  
link-protocol hdlc  
link-protocol lapb  
link-protocol ppp  
Use the link-protocol hdlccommand to configure the interface encapsulation as HDLC.  
Use the link-protocol lapbcommand to specify the link layer protocol of the interface as LAPB.  
Use the link-protocol pppcommand to configure the link-layer protocol encapsulated on the interface as  
PPP.  
Interface view  
link-protocol sdlc  
Use the link-protocol sdlccommand to change the link layer encapsulation protocol of the synchronous  
serial interface into SDLC.  
Synchronous Serial Interface view  
link-protocol slip  
link-protocol sot  
link-protocol x25  
llc2 max-ack  
Use the link-protocol slipcommand to set the link layer protocol of the interface as SLIP.  
Use the link-protocol sotcommand to encapsulate the serial interface with SOT.  
Interface view  
Synchronous Serial Interface view  
Use the link-protocol x25command to encapsulate X.25 protocol to the specified interface.  
Interface view  
Use the llc2 max-ackcommand to configure the length of the advance response window before the LLC2  
sending the acknowledgement frame.  
Ethernet Interface view  
Ethernet Interface view  
Ethernet Interface view  
Ethernet Interface view  
llc2 max-send-queue  
llc2 max-transmission  
llc2 modulo  
Use the llc2 max-send-queuecommand to configure the queue length sending the LLC2 packet.  
Use the llc2 max-transmissioncommand to configure the retransmission times of the LLC2.  
Use the llc2 modulocommand to configure the modulus of the LLC2.  
 
94  
3Com Router 5000/6000 Family  
Command Reference  
llc2 receive-window  
Use the llc2 receive-windowcommand to configure the maximum packets that can be sent before the  
LLC2 receives the acknowledgement frame.  
Ethernet Interface view  
llc2 timer ack  
Use the llc2 timer ackcommand to configure the LLC2 local response time.  
Ethernet Interface view  
llc2 timer ack-delay  
Use the llc2 timer ack-delaycommand to configure the local acknowledgement delay time when the  
LLC2 receives information frames.  
Ethernet Interface view  
Ethernet Interface view  
Ethernet Interface view  
Ethernet Interface view  
llc2 timer busy  
llc2 timer poll  
llc2 timer reject  
loadbandwidth  
local  
Use the llc2 timer busycommand to configure the LLC2 BUSY time.  
Use the llc2 timer pollcommand to configure the P/F waiting time of the LLC2.  
Use the llc2 timer rejectcommand to configure the REJ time of the LLC2.  
Use the loadbandwidthcommand to allocate load bandwidth to the interface.  
Interface (Excluding Logical Interfaces) view  
IKE-Peer view  
Use the localcommand to configure the subnet type in IKE negotiation.  
local-address  
local-server  
local-user  
Use the local-addresscommand to configure the IP address of the local GW in IKE negotiation.  
lUse the local-servercommand to configure a local RADIUS authentication server.  
lUse the local-usercommand to configure the user name and password of a client.  
Use the local-usercommand to add a local user and enter the local user view.  
IKE-Peer view  
System view  
Dvpn-Class view  
System view  
local user  
local-user password-display-mode  
Use the local-user password-display-modecommand to configure the password display mode of all the  
local users.  
System view  
locality  
lock  
Use the localitycommand to name the geographical locality of an entity, by a city for example.  
PKI Entity view  
Use the lockcommand to lock the active user interface and prevent unauthorized users from accessing it.  
The active user interface can be console, AUX, or VTY.  
User view  
ASPF Policy view  
BGP view  
log enable  
Use the log enablecommand to enable ASPF session logging function.  
log-peer-change  
log-peer-change  
Use the log-peer-changecommand to turn on the BGP adjacency changes output switch.  
Use the log-peer-changecommand to configure to log the IS-IS adjacency changes.  
IS-IS view  
 
3Com Router 5000/6000 Family  
Command Reference  
95  
log-peer-change  
Use the log-peer-changecommand to turn on the OSPF adjacency changes output switch for the current  
OSPF process.  
OSPF view  
User view  
log startup  
loopback  
loopback  
loopback  
loopback  
Use the log startupcommand to turn on the configuration restoration log switch.  
Use the loopbackcommand to enable the loopback function on an ATM OC-3c/STM-1 interface.  
Use the loopbackcommand to configure the loopback mode on the ATM E1/T1 interface.  
Use the loopbackcommand to enable loopback function of interface.  
Use the loopbackcommand to enable a serial interface to perform loopback.  
ATM Interface view  
ATM E1/T1 Interface views  
ATM E3/T3 Interface view  
AM Interface view  
AUX Interface view  
Serial Interface view  
loopback  
loopback  
loopback  
loopback  
Use the loopbackcommand to set the loopback mode on the interface.  
CE1/PRI interface view  
CPOS Interface view  
Ethernet Port view  
Use the loopbackcommand to configure the loopback function of the CPOS interface.  
Use the loopbackcommand to enable loopback on the Ethernet port for test purpose.  
Use the loopbackcommand to configure the loopback function of the POS interface.  
POS Interface view  
CE1/PRI Interface view  
CE3 Interface view  
loopback (CE1/PRI Interface)  
Use the loopbackcommand to enable a CE1/PRI interface to perform loopback.  
loopback (CE3 Interface)  
Use the loopbackcommand to configure the loopback mode of a CE3 interface.  
loopback (CT1/PRI Interface)  
Use the loopbackcommand to enable a CT1/PRI interface to perform local, remote, or external payload  
loopback.  
CT1/PRI Interface view  
loopback (CT3 Interface)  
Use the loopbackcommand to configure the loopback mode of the CT3 interface.  
CT3 Interface view  
loopback (Ethernet/GE Interface)  
Use the loopbackcommand to enable local loopback on the Ethernet interface.  
Ethernet Interface view  
loopback (ISDN BRI Interface)  
Use the loopbackcommand to place the B1, B2, or both channels on the BRI interface in a remote looback.  
This can send data from a line back to the line.  
ISDN BRI Interface view  
looptest  
Use the looptestcommand to test whether an interface or line is in a loop.  
Any view  
lr  
Use the lrcommand to configure LR.  
Traffic Behavior view  
 
96  
3Com Router 5000/6000 Family  
Command Reference  
lr percent  
1Use the lr percentcommand to configure LR.  
Traffic Behavior view  
FTP Client view  
ls  
Use the lscommand to query for a specified file/directory.  
ls  
Use the lscommand to view the files in the specified directory as you would with the dircommand.  
Use the lsp-triggercommand to configure topology-triggered LSP creation policy.  
Use the mac-addresscommand to configure Mac address of virtual Ethernet interface.  
SFTP Client view  
MPLS view  
lsp-trigger  
mac-address  
mac-address timer aging  
mandatory-chap  
Virtual Ethernet Interface view  
Use the mac-address timer agingcommand to set the aging timer for the MAC address table on the port.  
Ethernet Port view  
L2TP Group view  
Use the mandatory-chapcommand to force LNS to perform CHAP authentication again with the client.  
mandatory-lcp  
Use the mandatory-lcpcommand to allow LNS and client to renegotiate Link Control Protocol (LCP)  
between them.  
L2TP Group view  
PVC view  
map bridge  
map bridge-group  
map clns  
Use the map bridgecommand to establish the IPoEoA mapping or PPPoEoA mapping on the PVC.  
Use the map bridge-group broadcastcommand to enable the PVC to transmit and receive BPDUs.  
Use the map clnscommand to create a CLNSOA mapping for a PVC.  
PVC view  
ATM PVC view  
PVC view  
map ip  
Use the map ipcommand to create IPoA mapping for PVC.  
map ppp  
Use the map pppcommand to create a PPPoA map on the PVC.  
PVC view  
map routed-bridge  
Use the map routed-bridgecommand to configure routed bridge encapsulation on the PVC.  
ATM PVC view  
match  
Use the matchcommand to configure a PVC group to differentiate traffic by the Precedence or DSCP  
identifier in the TOS field of the IP header.  
ATM Pvc-Group view  
Voice Entity view  
match-template  
Use the match-templatecommand to configure the match template for a voice entity.  
max-call (in Voice Dial Program View)  
Use the max-callcommand to configure max-call sets (128 sets at most).  
Voice Dial Program view  
Voice Entity view  
max-call (in Voice Entity View)  
Use the max-callcommand to bind a voice entity to the max-call set specified by set-number.  
 
3Com Router 5000/6000 Family  
Command Reference  
97  
max-packet-process  
Use the max-packet-processcommand to set the maximum number of processed packets per second on  
a certain VLAN.  
System view  
md5-compatible  
Use the md5-compatiblecommand to configure ISIS to use the 3Com-compatible MD5 algorithm. You  
need to use this command when MD5 authentication on ISIS is required between your router and a 3Com  
device.  
ISIS view  
CT3 Interface view  
System view  
mdl (CT3 Interface)  
Use the mdlcommand to configure MDL message detection/sending on the CT3 interface.  
Use the memorycommand to configure the safety value and lower limit of the router idle memory.  
memory  
memory auto-establish disable  
Use the memory auto-establish disablecommand to disable the function of restoring the connections of  
all the routing protocols (even if the idle memory reduces to a safety value).  
Use the memory auto-establish disablecommand to disable the above function.  
System view  
memory auto-establish enable  
Use the memory auto-establish enablecommand to resume connections of all the routing protocols when  
the idle memory of the router recovers to a safety value.  
Use the memory auto-establish disablecommand to disable the above function. Use the memory  
auto-establish enablecommand to enable the above function again. By default, the function is always  
enabled.  
System view  
R2 CAS view  
mfc (R2 CAS)  
Use the mfccommand to maintain of MFC channel of the specified timeslot.  
Use the mfr bundle-namecommand to set frame relay bundle identification (BID).  
Use the mfr fragmentcommand to enable FRF.16 fragmentation on the MFR bundle.  
mfr bundle-name  
mfr fragment  
MFR Interface view  
MFR Interface view  
mfr fragment-size  
Use the mfr fragment-sizecommand to configure the maximum fragment size allowed on a frame relay  
bundle link.  
Frame Relay Interface view  
MFR Interface view  
mfr link-name  
mfr retry  
Use the mfr link-namecommand to set the frame relay bundle link identification (LID).  
Frame Relay Interface view  
Use the mfr retrycommand to set the maximum times that a frame relay bundle link can resend hello  
message when waiting for a hello acknowledgement message.  
Frame Relay Interface view  
mfr timer ack  
Use the mfr timer ackcommand to set the time of waiting for hello acknowledgment message before  
frame relay bundle link resends hello message.  
Frame Relay Interface view  
mfr timer hello  
mfr window-size  
Use the mfr timer hellocommand to set the interval for a frame relay bundle link to send hello message.  
Frame Relay Interface view  
Use the mfr window-sizecommand to configure the number of fragments that can be held by the window  
used in sliding window algorithm when multilink frame relay reassembles received fragments.  
MFR Interface view  
 
98  
3Com Router 5000/6000 Family  
Command Reference  
min-active-links  
Use the min-active-links command to configure the minimum number of available links required for the  
IMA group to operate.  
IMA Group Interface view  
mkdir  
Use the mkdircommand to create a directory on the remote FTP server.  
Use the mkdir command to create a directory on the remote SFTP server.  
FTP Client view  
mkdir  
SFTP Client view  
mkdir  
Use the mkdircommand to create a directory under the specified directory on the specified storage device.  
Use the mobile-ipcommand to enable the MIP function.  
User view  
System view  
System view  
Interface view  
System view  
mobile-ip  
mobile-ip foreign-agent  
Use the mobile-ip foreign-agentcommand to set foreign agent care-of addresses and the pending time.  
mobile-ip foreign-agent service  
Use the mobile-ip foreign-agent servicecommand to enable FA service on an interface.  
mobile-ip home-agent  
Use the mobile-ip home-agentcommand to enable HA service on a router.  
mobile-ip home-agent mobile-router  
Use the mobile-ip home-agent mobile-routercommand to configure an MR on an HA. This command  
will bring you to HA-MR view.  
System view  
Interface view  
System view  
mobile-ip irdp  
Use the mobile-ip irdpcommand to enable IRDP and configure the relevant attributes on an interface.  
mobile-ip mobile-router  
Use the mobile-ip mobile-routercommand to enable the MR function and enter MR view.  
mobile-ip mobile-router ccoa  
Use the mobile-ip mobile-router ccoa onlycommand to specify that the interface can only use a  
co-located care-of address to register.  
Use the mobile-ip mobile-router ccoa only gatewaycommand to configure the default gateway for the  
interface using a co-located care-of address to register.  
Interface view  
Interface view  
Interface view  
mobile-ip mobile-router roam  
Use the mobile-ip mobile-router roamcommand to enable the roaming function on the interface, that  
is, to allow the interface to function as the roaming interface of the MR.  
mobile-ip mobile-router solicit  
Use the mobile-ip mobile-router solicitcommand to configure agent solicitation retransmission  
parameters.  
mobile-ip prefix-length  
Use the mobile-ip prefix-lengthcommand to add the prefix-length extension part in the agent  
advertisement.  
Interface view  
Interface view  
System view  
mobile-ip registration-lifetime  
Use the mobile-ip registration-lifetimecommand to set the registration lifetime of the MN.  
mobile-ip secure  
Use the mobile-ip securecommand to configure mobility security associations on HAs, FAs, and MRs.  
 
3Com Router 5000/6000 Family  
Command Reference  
99  
mobile-ip tunnel path-mtu-discovery  
Use the mobile-ip tunnel path-mtu-discoverycommand to set the PMTU update policy.  
System view  
System view  
HA-MR view  
MR view  
mobile-ip virtual-network  
Use the mobile-ip virtual-networkcommand to define a virtual network.  
mobile-network  
mobile-network  
mobile-node  
Use the mobile-networkcommand to configure a mobile network for an MR.  
Use the mobile-networkcommand to configure a mobile network for the MR.  
Use the mobile-nodecommand to set MN attributes, including the interface or virtual network and the  
registration lifetime.  
System view  
R2 CAS view  
SIP Client view  
mode  
Use the modecommand to configure the R2 signaling mode in a country or region.  
mode (SIP Client view)  
Use the modecommand to set the registration mode of the gateway.  
modem  
Use the modemor modem bothcommand to allow modem calls to pass through, both incoming and outgoing.  
Use the modem[ call-in | call-out ]command to allow incoming or outgoing modem calls to pass  
through.  
User Interface view  
User Interface view  
modem adapt no-waiting-connect  
Use the modem adapt no-waiting-connect command to set the asynchronous serial interface Modem to  
switch from IDLE to ACTIVE without waiting for receiving the signal CONNECT (a signal used for a physical  
modem to negotiation rate) after it receives CD_UP (a lower layer detects carrier signal).  
modem auto-answer  
modem auto-answer  
Use the modem auto-answercommand to have the external modem connected to the asynchronous  
interface automatically answer or hook off.  
User Interface view  
User Interface view  
Use the modem auto-answercommand to set the answering mode to auto-answer.  
modem compatible-param  
Use the modem compatible-paramcommand in the case that you fail to use standard Modem PCM to  
interoperate with devices from other vendors.  
Voice Entity view  
modem protocol  
Use the modem protocol noneprotocol to disable Modem function for single voice entity.  
Use the modem protocol pcmcommand to configure PCM Modem protocol type for single voice entity,  
including coding/decoding and Modem negotiation mode.  
Voice Entity view  
modem timer answer  
Use the modem timer answercommand to set the timeout time spent waiting for the carrier signal after the  
off-hook action when setting up an incoming call connection.  
User Interface view.  
monitor-port  
Use the monitor-portcommand to specify the current port as the monitoring port  
Ethernet Interface view  
User view  
more  
Use the morecommand, you can view the contents of the specified file.  
 
100  
3Com Router 5000/6000 Family  
Command Reference  
motorola base-svc  
Use the motorola base-svccommand to configure the start SVC for voice routing on a DLCI.  
DLCI view  
DLCI view  
motorola encapsulation  
Use the motorola encapsulationcommand to specify an encapsulation for Motorola LCON on the DLCI.  
motorola max-voice  
Use the motorola max-voicecommand to configure the maximum number of voice channels created on a  
DLCI concurrently.  
DLCI view  
DLCI view  
User view  
motorola remote-id  
Use the motorola remote-idcommand to configure a remote connection ID.  
Use the movecommand to move a file.  
move  
mpls  
Use the mplscommand in system view to enable MPLS globally and enter MPLS view.  
Use the mplscommand in interface view to enable MPLS on the interface.  
Interface view  
Routing Protocol view  
System view  
Virtual Interface view  
mpls l2vc  
Use the mpls l2vccommand to create an LDP connection.  
Use the mpls l2vpncommand to enable L2VPN.  
Interface view  
System view  
mpls l2vpn  
mpls l2vpn encapsulation  
Use the mpls l2vpn encapsulationcommand to create Kompella MPLS L2VPN, specify encapsulation  
type, and enter MPLS L2VPN view.  
System view  
mpls-exp  
Use the mpls-expcommand to configure the PVC to carry packets of the specified priority levels when the  
EXP identifier in the MPLS packet is used to identify the priority levels of packets.  
ATM Pvc-Group view  
mpls label advertise  
Use the mpls label advertisecommand to specify at the egress the type of the label to be distributed to  
the penultimate hop.  
MPLS view  
System view  
Interface view  
System view  
System view  
mpls ldp  
Use the mpls ldpcommand to enable LDP.  
mpls ldp enable  
mpls ldp hops-count  
mpls ldp loop-detect  
mpls ldp password  
Use the mpls ldp enablecommand to enable LDP on the interface.  
Use the mpls ldp hops-countcommand to set the maximum hops of loop detection.  
Use the mpls ldp loop-detectcommand to enable loop detection.  
Use the mpls ldp passwordcommand to configure LDP authentication mode.  
Interface view  
Remote-Peer view  
 
3Com Router 5000/6000 Family  
Command Reference  
101  
mpls ldp path-vectors  
Use the mpls ldp path-vectorscommand to set the maximum value of path vector.  
System view  
mpls ldp remote-peer  
Use the mpls ldp remote-peercommand to create a remote-peer entity and enter remote-peer view.  
Remote-Peer view  
System view  
mpls ldp reset-session  
Use the mpls ldp reset-sessioncommand to reset a specified session on an interface.  
Interface view  
mpls ldp timer  
Use the mpls ldp timercommand to set the duration of a Hello hold timer or session hold timer.  
Interface view  
Remote-Peer view  
mpls ldp transport-ip  
mpls lsr-id  
mpls static-l2vc  
msdp  
Use the mpls ldp transport-ipcommand to configure an LDP session transport address.  
Interface view  
System view  
Use the mpls lsr-id command to configure an LSR ID.  
Use the mpls static-l2vccommand to create an SVC MPLS L2VPN connection.  
Use the msdpcommand to enable MSDP and enter the MSDP view.  
Interface view  
System view  
msdp-tracert  
Use the msdp-tracertcommand to trace the transmission path of SA messages in the network.  
Use the mtucommand to set the size of Maximum Transmission Unit (MTU) of the ATM interface.  
Use the mtucommand to configure MTU of Kompella MPLS L2VPN.  
Any view  
mtu  
Interface view  
mtu  
MPLS L2VPN view  
Interface view  
mtu (ATM Interface)  
Use the mtucommand to set the MTU size of the ATM interface.  
mtu (Ethernet/GE Interface)  
Use the mtucommand to set the MTU size of the Ethernet interface.  
Ethernet Interface view  
mtu label-including  
mtu (POS Interface)  
Use the mtu label-includingcommand to configure to include MPLS label length in outgoing interface  
MTU calculation.  
MPLS view  
Use the mtucommand to set the MTU size of the POS interface.  
POS Interface view  
mtu (serial interface)  
Use the mtucommand to set MTU of the serial interface.  
AM Interface view  
AUX Interface view  
Serial Interface view  
mtu (Tunnel Interface)  
Use the mtucommand to set the maximum transmission unit (MTU) for Tunnel interface.  
Tunnel Interface view  
 
102  
3Com Router 5000/6000 Family  
Command Reference  
mtracert  
Use the mtracertcommand to trace the network path from the multicast source to the destination receiver  
along Multicast Distribution Tree, according to either the multicast kernel routing table or RPF rule to the  
source.  
Any view  
OSPF view  
multi-path-number  
Use the multi-path-numbercommand to configure maximum number of OSPF equal-cost routes.  
Use the multicast minimum-ttlcommand to configure the minimum TTL value for multicast forwarding.  
multicast minimum-ttl  
Interface view  
Interface view  
multicast packet-boundary  
Use the multicast packet-boundarycommand to configure a multicast forwarding boundary.  
multicast route-limit  
Use the multicast route-limitcommand to limit the multicast routing table capacity. If the capacity  
exceeds the limit, the router will discard protocols and data packets of the newly-added (S, G).  
System view  
System view  
multicast routing-enable  
Use the multicast routing-enablecommand to enable IP multicast routing.  
multiplex mode  
Use the multiplex modecommand to set AUG multiplexing mode.  
CPOS Interface view  
nas-ip  
Use the nas-ipcommand to set the source IP address of the network access server (NAS, the router in this  
manual), so that all packets destined for the RADIUS server carry the same source IP address.  
RADIUS view  
nas-ip  
Use the nas-ipcommand to have all the TACACS+ packets sent by the NAS (the router) carry the same  
source address.  
TACACS+ view  
System view  
System view  
System view  
System view  
nat address-group  
nat aging-time  
nat agl  
Use the nat address-groupcommand to configure an address pool.  
Use the nat aging-timecommand to set the lifetime of NAT connections.  
Use the nat algcommand to enable the application gateway function of NAT.  
nat connection-limit-policy  
Use the nat connection-limit-policycommand to specify the NAT connection limit policy.  
nat dns-map  
nat oubound  
Use the nat dns-mapcommand to configure a NAT entry, mapping a domain name to a triplet of external  
IP address, port number, and protocol type.  
System view  
Interface view  
Use the nat outboundcommand to associate an ACL with an address pool, indicating that the address  
specified in the acl-numbercan be translated by using address pool group-number.  
nat outbound interface  
Use the nat outbound interfacecommand to associate an ACL with an interface and to use the address  
of the interface as the target address in the translations for the packets matching the ACL. After that, this  
address substitutes for the source addresses of the packets matching the ACL.  
Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
103  
nat outbound static  
Use the nat outbound staticcommand to apply on the interface one-to-one address translation  
configured using the nat static command.  
Interface view  
System view  
nat overlapaddress  
nat server  
Use the nat overlapaddresscommand to map an overlapping address pool to a temporary address pool.  
Use the nat servercommand to define a mapping table for internal servers. Users can access the internal  
server with the address and port as host-addr and host-port respectively through the address port defined  
by global-addr and global-port.  
Interface view  
System view  
nat static  
Use the nat staticcommand to configure a one-to-one private-to-public address binding.  
nat static inside  
Use the nat static inside command to create a static net-to-net NAT entry. When the router translates  
addresses based on this type of NAT entry, it translates the network address portion without touching the  
host address portion.  
System view  
IKE-Peer view  
nat traversal  
national-bit  
naturemask-arp  
Use the nat traversalcommand to configure the NAT traversal function of IKE/IPSec.  
Use the national-bitcommand to configure national bit on the CE3 interface.  
CE3 Interface view  
Use the naturemask-arp enablecommand to support ARP within natural network segments rather than  
subnets.  
System view  
nbns-list  
Use the nbns-listcommand to configure NetBIOS server addresses in a global DHCP address pool for  
the clients.  
DHCP Address Pool view  
nesting  
Use the nestingcommand to configure a nesting rule.  
ACL view  
netbios-type  
Use the netbios-typecommand to configure the NetBIOS node type of the clients of a global DHCP  
address pool.  
DHCP Address Pool view  
network  
network  
network  
network  
network  
Use the networkcommand to configure the network routes advertised by the local BGP system.  
Use the networkcommand to configure an IP address range used for dynamic allocation.  
Use the networkcommand to configure the network addresses to be sent by the local BGP.  
BGP view  
DHCP Address Pool view  
IPv4 Multicast Subaddress Family view  
OSPF Area view  
Use the networkcommand to configure the interface running OSPF.  
Use the networkcommand to enable Routing Information Protocol (RIP) on the interface.  
RIP view  
 
104  
3Com Router 5000/6000 Family  
Command Reference  
network-entity  
Use the network-entitycommand to configure the name of Network Entity Title (NET) of the IS-IS routing  
process.  
IS-IS view  
normal-connect slow-h245  
Use the normal-connect slow-h245command to configure disabling the calling end from actively initiating  
an H245 connection request to the called end before the called end is hooked off in voice entity view.  
Use the normal-connect slow-h245 command to disable the calling end from actively initiating an H245  
connection request to the called end before the called end is hooked off in voice entity view.  
VoIP Voice Entity view  
nslookup type  
Use the nslookup typecommand to resolve the specified IP address or domain name to a domain name  
or IP address.  
Any view  
OSPF Area view  
System view  
nssa  
Use the nssacommand to configure an area as NSSA area.  
Use the ntp-service accesscommand to control access to the NTP service on the local device.  
ntp-service access  
ntp-service authentication enable  
Use the ntp-service authentication enablecommand to enable NTP service ID authentication.  
System view  
ntp-service authentication-keyid  
Use the ntp-service authentication-keyidcommand to set an NTP authentication key.  
System view  
ntp-service broadcast-client  
Use the ntp-service broadcast-clientcommand to configure NTP broadcast client mode.  
Interface view  
Interface view  
ntp-service broadcast-server  
Use the ntp-service broadcast-servercommand to configure NTP broadcast server mode.  
ntp-service max-dynamic-sessions  
Use the ntp-service max-dynamic-sessionscommand to set the number of sessions allowed by the local  
device.  
System view  
Interface view  
Interface view  
ntp-service multicast-client  
Use the ntp-service multicast-clientcommand to configure NTP multicast client mode.  
ntp-service multicast-server  
Use the ntp-service multicast-servercommand to configure NTP multicast server mode.  
ntp-service refclock-master  
Use the ntp-service refclock-mastercommand to set the local clock as the NTP master clock to provide  
synchronization source.  
System view  
System view  
ntp-service reliable authentication-keyid  
Use the ntp-service reliable authentication-keyid command to specify a reliable key.  
ntp-service source-interface  
Use the ntp-service source-interfacecommand to specify an interface for the local end to transmit NTP  
messages.  
System view  
System view  
System view  
ntp-service unicast-peer  
Use the ntp-service unicast-peercommand to configure NTP peer mode.  
ntp-service unicast-server  
Use the ntp-service unicast-servercommand to configure NTP server mode.  
 
3Com Router 5000/6000 Family  
Command Reference  
105  
number-match  
Use the number-matchcommand to configure a global number match-policy.  
Voice Dial Program view  
number-substitute  
oam ais-rdi  
Use the number-substitutecommand to create a number-substitute list and enter voice dial program view.  
Voice Dial Program view  
Use the oam ais-rdicommand to change the parameters related to AIS/RDI alarm cell detection. If no  
argument is specified, the default value applies.  
ATM Class view  
PVC view  
oam frequency  
Use the oam frequencycommand to enable the transmission of OAM F5 Loopback cell so as to check the  
PVC status. You can also enable OAM F5 Loopback retransmission check or modify the related parameters  
of the retransmission check.  
ATM Class view  
PVC view  
oamping interface  
Use the oamping interfacecommand to enable the specified ATM interface to send OAM cells on the  
specified PVC for checking link state. Receiving no response upon expiration of the specified time indicates  
that the link is disconnected, busy, or prone to packet loss.  
ATM Interface view  
OSPF view  
opaque-capability  
Use the opaque-capability enablecommand to enable the Opaque capability of OSPF.  
Use the opencommand to set up control connection to the remote FTP server.  
Use the open-trunkcommand to enable E&M non-signaling mode.  
open  
FTP Client view  
open-trunk  
Analog E&M Voice Subscriber Line view  
option  
Use the optioncommand to configure the self-defined options for a DHCP global address pool.  
DHCP Address Pool view  
PKI Entity view  
organization  
organizational-unit  
Use the organizationcommand to specify the name of the organization to which the entity belongs.  
Use the organizational-unitcommand to specify the name of the organization unit to which this entity  
belongs.  
PKI Entity view  
MSDP view  
originating-rp  
Use the originating-rpcommand to allow a MSDP to use the IP address of specified interface as the RP  
address in the SA message originated.  
osm connect slot  
Use the osm connect slotcommand to connect the current control terminal to the OSM board to manage  
the system on the OSM board. If you want to return from the OSM board to the operation interface on the  
router, click hot key <Ctrl+k>.  
User view  
User view  
User view  
osm reboot slot  
osm reload slot  
osm shutdown slot  
Use the osm reboot slotcommand to reset the OSM board.  
Use the osm reload slotcommand to restart the operation system on OSM board.  
Use the osm shutdown slotcommand to shut down the operation system on OSM board. This operation  
equals to execute the turn off command on the operation system of OSM board.  
User view  
 
106  
3Com Router 5000/6000 Family  
Command Reference  
ospf  
Use the ospfcommand to enable the OSPF protocol.  
System view  
ospf authentication-mode  
Use the ospf authentication-modecommand to configure the authentication mode and key between  
adjacent routers.  
Interface view  
Interface view  
ospf cost  
Use the ospf costcommand to configure different packet sending costs so as to send packets from  
different interfaces.  
ospf dr-priority  
Use the ospf dr-prioritycommand to configure the priority for electing the "designated router" on an  
interface.  
Interface view  
System view  
Interface view  
Interface view  
Interface view  
ospf mib-binding  
ospf mtu-enable  
ospf network-type  
ospf timer dead  
ospf timer hello  
Use the ospf mib-bindingcommand, MIB operation can be bound on the specified OSPF process.  
Use the ospf mtu-enablecommand to enable the interface to write MTU value when sending DD packets.  
Use the ospf network-typecommand to configure the network type of OSPF interface.  
Use the ospf timer deadcommand to configure the dead interval of the OSPF neighbor.  
Use the ospf timer hellocommand to configure the interval for transmitting Hello messages on an  
interface.  
Interface view  
ospf timer poll  
Use the ospf timer pollcommand to configure the poll Hello message interval on nbma and p2mp  
network.  
Interface view  
Interface view  
Interface view  
System view  
ospf timer retransmit  
ospf trans-delay  
ospf vpn instance  
option  
Use the ospf timer retransmitcommand to configure the interval for LSA re-transmitting on an interface.  
Use the ospf trans-delaycommand to configure the LSA transmitting delay on an interface.  
Use the ospfcommand to enable an OSPF process.  
Use the optioncommand to specify the logical relationship between the addresses to be probed in the  
detect group.  
Detect Group view  
Voice Entity view  
Voice Entity view  
outband  
Use the outbandcommand to configure transmission of DTMF code in the outband mode.  
Use the outband vofrcommand to configure out-of-band transmission of DTMF codes.  
outband vofr  
overlap voip h323  
Use the overlap voip h323command to configure the calling party to support h323 overlap mode for  
sending numbers.  
Voice Dial Program view  
 
3Com Router 5000/6000 Family  
Command Reference  
107  
packing timer  
Use the packing-timercommand to set the maximum waiting time for one PVC.  
PVC view  
User view  
pad  
Use the padcommand to establish a PAD connection with the remote site.  
Use the pad-mode pos enablecommand to enable POSPAD access mode.  
Use the paritycommand to set the check bit of the user interface.  
Use the passivecommand to set data transmission mode to passive.  
pad-mode pos enable  
Synchronous Serial Interface view  
User Interface view  
parity  
passive  
FTP Client view  
password  
Use the passwordcommand to configure the password required for logging onto the FTP server.  
Use the passwordcommand to configure a password for a local user.  
HWPing Test Group view  
Local User view  
password  
password-digit  
Use the password-digitcommand to configure the user password digits of a certain access service  
number in the card number process.  
Voice Access-Number view  
payload-size  
Use the payload-sizecommand to notify the underlying layer how much time DSP spends assembling a  
voice packet, or the time length of each voice packet.  
Voice Entity view  
pcm  
Use the pcmcommand to configure a companding law used for quantizing signals.  
Voice Subscriber-Line view  
peer  
Use the peercommand to configure the destination address of the peer to which information is sent in  
unicast mode.  
RIP view  
peer  
peer  
Use the peercommand to configure an MSDP peer.  
MSDP view  
Use the peercommand to configure the IP address of adjacent routers and specify a DR priority on an  
NBMA network.  
OSPF view  
peer  
Use the peercommand to configure the subnet type in IKE negotiation.  
IKE-Peer view  
peer advertise-community  
Use the peer advertise-communitycommand to enable the transmission of community attributes to a peer  
group.  
BGP view  
VPNv4 view  
VPN Instance view  
peer advertise-community  
Use the peer advertise-communitycommand to configure to advertise community attributes to a peer  
(group).  
IPv4 Multicast Subaddress Family view  
 
108  
3Com Router 5000/6000 Family  
Command Reference  
peer allow-as-loop  
Use the peer allow-as-loopcommand to configure the repeating times of the local AS number.  
BGP view  
VPNv4 view  
VPN Instance view  
peer allow-as-loop  
Use the peer allow-as-loopcommand to allow the AS_PATH attribute in the received routes to include  
the local AS number.  
IPv4 Multicast Subaddress Family view  
peer as-number  
Use the peer as-numbercommand to specify an AS number for a peer group.  
BGP view  
peer as-path-acl  
Use the peer as-path-aclcommand to specify BGP route filtering policy based on AS path list for a  
peer/peer group.  
BGP view  
VPNv4 view  
VPN Instance view  
peer as-path-acl  
Use the peer as-path-acl importcommand to have MBGP filter the routes received from the specified  
peer or peer group based on the specified AS path list.  
Use the peer as-path-acl exportcommand to have MBGP filter the routes advertised to the specified  
peer or peer group.  
IPv4 Multicast Subaddress Family view  
peer connect-interface  
Use the peer connect-interfacecommand to specify the source interface for route updates.  
BGP view  
BGP view  
peer default-route-advertise  
Use the peer default-route-advertisecommand to redistribute a default route to a peer group.  
peer default-route-advertise  
Use the peer default-route-advertisecommand to enable a peer (group) to import a default route.  
BGP view  
MBGP IPv4-Family view  
peer description  
peer description  
peer ebgp-max-hop  
Use the peer descriptioncommand to configure the description information of the peer/peer group.  
Use the peer descriptioncommand to configure descriptive text to MSDP peer.  
BGP view  
MSDP view  
Use the peer ebgp-max-hopcommand to allow establishing EBGP connection with a neighbor on an  
indirectly connected network.  
BGP view  
peer enable  
Use the peer enablecommand to enable the specified peer (group).  
BGP Unicast Address Family view  
L2VPN Address Family view  
IPv4 Multicast Sub-address Family view  
VPNv4 Address Family view  
peer enable  
peer enable  
Use the peer enablecommand to enable the multicast peer or peer group.  
IPv4 Multicast Subaddress Family view  
Use the peer enablecommand to activate the specified peer (group) in L2VPN address family view.  
L2VPN Address Family view  
 
3Com Router 5000/6000 Family  
Command Reference  
109  
peer filter-policy  
Use the peer filter-policy importcommand to configure BGP to filter routes received from the peer  
(group) based on the ACL.  
Use the peer filter-policy exportcommand to configure BGP to filter routes advertised to the peer  
(group) based on the ACL.  
BGP view  
IPv4 Multicast Sub-Address Family view  
peer filter-policy  
Use the peer filter-policy importcommand to have MBGP filter the routes received from the specified  
peer or peer group based on the specified ACL.  
Use the peer filter-policy exportcommand to have MBGP filter the routes advertised to the specified  
peer or peer group based on the specified ACL.  
IPv4 Multicast Subaddress Family view  
peer group  
Use the peer groupcommand to add a peer to a peer group.  
BGP view  
peer ip-prefix  
Use the peer ip-prefix importcommand to configure BGP to filter routes received from the peer/peer  
group based on the ip-prefix list.  
Use the peer ip-prefix exportcommand to configure BGP to filter routes advertised to the peer/peer  
group based on the ip-prefix list.  
BGP view  
VPNv4 view  
VPN Instance view  
peer ip-prefix  
Use the peer ip-prefix importcommand to have MBGP filter the routes received from the specified peer  
or peer group based on the specified address prefix list.  
Use the peer ip-prefix exportcommand to have MBGP filter the routes advertised to the specified peer  
or peer group based on the specified address prefix list.  
IPv4 Multicast Subaddress Family view  
peer label route-capability  
Use the peer label-route-capabilitycommand to enable the capability of a peer to process IPv4 routes  
with labels.  
BGP view  
peer mesh-group  
peer minimum-ttl  
Use the peer mesh-groupcommand to configure an MSDP peer to join an Mesh Group.  
MSDP view  
Use the peer minimum-ttlcommand to configure the minimum TTL (Time-to-Live) value of the multicast  
data packets encapsulated in SA messages to be sent to specified MSDP peer.  
MSDP view  
peer next-hop-invariable  
Use the peer next-hop-invariablecommand to configure the invariable next hop when sending routes  
to EBGP peers.  
BGP view  
BGP VPN-Instance view  
BGP-VPNv4 Subaddress Family view  
BGP-IPv4 Multicast Subaddress Family view  
peer next-hop-local  
peer next-hop-local  
peer password  
Use the peer next-hop-localcommand to configure the next hop in the route to be advertised to the peer  
group as the address of the local router.  
BGP view  
Use the peer next-hop-localcommand to remove the processing of the next hop in routes which BGP  
will advertise to the peer (group) and set the local address as the next hop.  
IPv4 Multicast Subaddress Family view  
Use the peer passwordcommand to configure BGP to perform MD5 authentication before setting up a TCP  
connection.  
BGP view  
MBGP VPN-Instance Address Family view  
 
110  
3Com Router 5000/6000 Family  
Command Reference  
peer public-as-only  
Use the peer public-as-onlycommand to configure not to carry the private AS number when transmitting  
BGP updates.  
BGP view  
peer public-as-only  
Use the peer public-as-onlycommand to configure only to carry public AS number rather than private  
AS number when BGP sends update packets.  
IPv4 Multicast Subaddress Family view  
peer-public-key end  
peer reflect-client  
Use the peer-public-key endcommand to return to system view from public key view.  
Public Key view  
Use the peer reflect-clientcommand to configure a peer group as the route reflector client.  
Use the peer reflect-clientcommand to configure a peer (group) as a client of the route reflector.  
BGP view  
VPNv4 view  
peer reflect-client  
IPv4 Multicast Subaddress Family view  
peer request-sa-enable  
Use the peer request-sa-enable command to enable the router to send SA request message to the  
specified MSDP peer when receiving a new group join message.  
MSDP view  
peer route-policy  
Use the peer route-policy importcommand to configure MBGP to filter routes received from the peer  
(group) based on the route-policy.  
Use the peer route-policy exportcommand to configure MBGP to filter routes advertised to the peer  
(group) based on the route-policy.  
BGP view  
VPNv4 view  
VPN Instance view  
peer route-policy  
Use the peer route-policy importcommand to have MBGP apply the specified routing policy to the  
routes received from the specified peer or peer group.  
Use the peer route-policy exportcommand to have MBGP apply the specified routing policy to the  
routes advertised to the specified peer or peer group.  
IPv4 Multicast Subaddress Family view  
peer route-update-interval  
Use the peer route-update-intervalcommand to configure the interval for a peer group to advertise  
route updates.  
BGP view  
VPNv4 view  
VPN Instance view  
peer sa-cache-maximum  
Use the peer sa-cache-maximumcommand to limit the number of caches originated when the router  
receives SA messages from an MSDP peer.  
MSDP view  
MSDP view  
MSDP view  
peer sa-policy  
Use the peer sa-policycommand to configure a filter list for SA messages received or forwarded from the  
specified MSDP peer.  
peer sa-request-policy  
Use the peer sa-request-policycommand to limit SA request messages that the router receives from  
MSDP peers.  
peer shutdown  
Use the peer shutdowncommand to disable the specified BGP peer or peer group to initiate or receive BGP  
connection or to disconnect a BGP connection that has existed.  
BGP view  
VPN Instance view  
 
3Com Router 5000/6000 Family  
Command Reference  
111  
peer timer  
Use the peer timercommand to configure Keepalive and Holdtime intervals for a peer (group).  
BGP view  
BGP view  
peer upe  
Use the peer upecommand to configure BGP peer as the UPE of hierarchical BGP/MPLS VPN.  
Use the permanent-activecommand to configure BSV interfaces to permanent active.  
permanent-active  
BSV Interface view (in NTmode)  
pfs  
Use the pfscommand to set the Perfect Forward Secrecy (PFS) feature for the IPSec policy to initiate the  
negotiation.  
IPSec Policy view  
IPSec Policy Template view  
phy-mru  
Use the phy-mrucommand to configure in asynchronous flow mode MRU at the physical layer.  
Asynchronous Serial Interface view  
physical-mode  
Use the physical-modecommand to set the operating mode of the synchronous/asynchronous serial  
interface.  
Serial Interface view  
System view  
pim  
Use the pimcommand to enter PIM view.  
pim bsr-boundary  
Use the pim bsr-boundarycommand to configure an interface to become the PIM domain boundary.  
Use the pim dmcommand to enable PIM-DM.  
Interface view  
Interface view  
pim dm  
pim neighbor-limit  
Use the pim neighbor-limitcommand to limit PIM neighbor number on an router interface. If the number  
exceeds the limit configured, no new neighbor can be added to the router.  
Interface view  
pim neighbor-policy  
Use the pim neighbor-policycommand to configure a router to filter the PIM neighbor of the current  
interface.  
Interface view  
Interface view  
Interface view  
Any view  
pim sm  
Use the pim smcommand to enable PIM-SM protocol on an interface.  
pim timer hello  
Use the pim timer hellocommand to configure the interval for sending PIM router Hello messages.  
Use the pingcommand to test connectivity of an IP network and reachability of a host.  
Use the ping clnscommand to test the reachability to a specified destination.  
ping  
ping clns  
ping ipx  
Any view  
Use the ping ipxcommand to check host reachability and network connectivity in IPX network.  
Any view  
pki delete-certificate  
Use the pki delete-certificatecommand to delete the locally stored certificates.  
System view  
 
112  
3Com Router 5000/6000 Family  
Command Reference  
pki domain  
Use the pki domaincommand to enter PKI domain view, and configure the parameters of LDAP server and  
for certificate request and authentication.  
System view  
Any view  
pki entity  
Use the pki entitycommand to name a PKI entity and enter PKI entity view.  
pki import-certificate  
Use the pki import-certificatecommand to import an existing CA certificate or local certificate.  
System view  
pki request-certificate  
Use the pki request-certificatecommand to deliver certificate request through SCEP to CA for the  
generated RSA key pair.  
System view  
System view  
pki retrieval-certificate  
Use the pki retrieval-certificatecommand to download a certificate from the certificate issuing server.  
pki retrieval-crl  
Use the pki retrieval-crlcommand to obtain the latest CRL from CRL server for the verification of the  
validity of a current certificate.  
System view  
System view  
pki validate-certificate  
Use the pki validate-certificatecommand to verify the validity of a certificate.  
plan-numbering  
Use the plan-numberingcommand to configure the calling/called numbering plan attribute of voice entities.  
Voice Entity view  
play stop-accounting-buffer  
Use the display stop-accounting-buffercommand to view information on the stop-accounting requests  
buffered in the router by RADIUS scheme, session ID, or time range. The displayed packet information can  
help you troubleshoot RADIUS faults.  
Any view  
plc-mode  
Use the plc-modecommand to configure packet loss compensation mode.  
Voice Subscriber-Line view  
policy vpn-target  
Use the policy vpn-targetcommand to filter the received routing information according to the VPN-target  
extended community attributes.  
BGP-VPNv4 Subaddress Family view  
port access vlan  
port hybrid pvid vlan  
port-mapping  
Use the port access vlancommand to add the port whose link type is access to a specified VLAN.  
Use the port hybrid pvid vlancommand to assign a default VLAN ID to the hybrid port.  
Use the port-mappingcommand to establish a mapping from the port to application layer protocol.  
Ethernet Port view  
Ethernet Port view  
System view  
port trunk permit vlan  
Use the port trunk permit vlancommand to assign the trunk port to the specified VLANs.  
Ethernet Port view  
Ethernet Interface view  
System view  
portal  
Use the portalcommand to enable portal authentication on an interface.  
portal all-resource-id  
Use the portal all-resource-id command to configure the all-resource ID.  
 
3Com Router 5000/6000 Family  
Command Reference  
113  
portal auth-network  
Use the portal auth-networkcommand to configure a network segment for portal authentication.  
System view  
System view  
System view  
System view  
System view  
System view  
System view  
System view  
System view  
System view  
portal fast-authentication  
Use the portal fast-authenticationcommand to enable fast portal authentication.  
portal free-ip  
portal free-user  
portal method  
Use the portal free-ipcommand to configure a free IP address.  
Use the portal free-usercommand to configure a portal authentication-free user.  
Use the portal methodcommand to specify a portal authentication method.  
Use the portal resourcecommand to create an accessible-resource name.  
Use the portal servercommand to configure a portal server or modify the configuration of a portal server.  
Use the portal service-typecommand to set the portal authentication mode.  
portal resource  
portal server  
portal service-type  
portal update-resource  
Use the portal update-resourcecommand to add an IP address to update resources.  
portal update-resource-id  
Use the portal update-resource-id command to configure the update-resource ID.  
portal upload-ip  
Use the portal upload-ipcommand to configure the IP address of the interface connected to the CAMS  
server.  
Ethernet Interface view  
pos-server app tcp  
pos-server app x25  
Use the pos-server app tcpcommand to configure a POS application in TCP/IP connection mode.  
System view  
Use the pos-server app x25command to configure the specified POS application on the POSPAD client  
router.  
System view  
System view  
System view  
System view  
System view  
System view  
pos-server checkschar  
pos-server enable  
pos-server fcm  
Use the pos-server checkscharcommand to enable the system to check POS packets for the string 10 04.  
Use the pos-server enablecommand to enable POS access server.  
Use the pos-server fcmcommand to configure FCM parameters for modem negotiation.  
Use the pos-server mapcommand to configure a multi-application POS access map entry.  
Use the pos-server padmodecommand to configure a POSPAD packet encapsulation format.  
pos-server map  
pos-server padmode  
 
114  
3Com Router 5000/6000 Family  
Command Reference  
pos-server source-ip  
Use the pos-server source-ipcommand to bind the specified application with the source address of a  
TCP connection.  
System view  
System view  
pos-server wait-time  
power-source  
Use the pos-server wait-timecommand to set the POSPAD wait timer.  
Use the power-sourcecommand to enable remote power supply.  
BSV Interface view (in NT mode)  
ppp authentication-mode  
Use the ppp authentication-modecommand to set the mode that the local PPP uses to authenticate the  
peer router.  
Interface view  
Virtual-Template Interface view  
ppp callback  
Use the ppp callbackcommand to enable an interface to send or accept PPP callback requests.  
Physical or Dialer Interface view  
ppp callback ntstring  
Use the ppp callback ntstringcommand to configure the dial number required for a Windows NT server  
to call back the router.  
Physical or Dialer Interface view  
ppp chap password  
ppp chap user  
Use the ppp chap passwordcommand to configure the password for CHAP authentication.  
Use the ppp chap usercommand to configure the user name when performing the CHAP authentication.  
Use the ppp compression iphccommand to enable IP header compression on the interface.  
Interface view  
Interface view  
Interface view  
ppp compression iphc  
ppp compression iphc rtp-connections  
Use the ppp compression iphc rtp-connectionscommand to designate the connections number of IP  
Header Compression allowed on one interface.  
Interface view  
ppp compression iphc tcp-connections  
Use the ppp compression iphc tcp-connectionscommand to configure the connection number of TCP  
compression mode.  
Interface view  
Interface view  
Interface view  
ppp compression stac-lzs  
Use the ppp compression stac-lzscommand to enable STAC-LZS compression for PPP.  
Use the ppp ipcp dnscommand to enable the router to allocate a DNS address to the peer.  
ppp ipcp dns  
ppp ipcp dns admit-any  
Use the ppp ipcp dns admit-anycommand to enable the router to accept the unsolicited DNS server  
address allocated by the peer without sending a DNS request.  
Interface view  
Interface view  
Interface view  
ppp ipcp dns request  
Use the ppp ipcp dns requestcommand to enable the router to request the peer for a DNS server  
address.  
ppp ipcp remote-address forced  
Use the ppp ipcp remote-address forcedcommand to forbid the peer to use the fix self-configured IP  
address but the one allocated by this router.  
 
3Com Router 5000/6000 Family  
Command Reference  
115  
ppp lcp mru consistent  
Use the ppp lcp mru consistentcommand to enable PPP LCP to negotiation maximum receive unit  
(MRU).  
Interface view  
Interface view  
ppp lqc  
Use the ppp lqccommand to enable PPP link quality control (LQC).  
Use the ppp mpcommand to enable the interface encapsulated with PPP to operate in the MP mode.  
Use the ppp mp binding-modecommand to set the MP binding condition.  
ppp mp  
Interface view  
ppp mp binding-mode  
Dialer Interface view  
Virtual Template Interface view,  
ppp mp lfi  
ppp mp lfi  
Use the ppp mp lficommand to configure the link fragmentation and interleaving features.  
Virtual Template Interface view  
Use the ppp mp lficommand to enable link fragmentation and interleaving (LFI) on the interface.  
MP-Group Interface view  
Virtual Template Interface view,  
ppp mp lfi delay-per-frag  
Use the ppp mp lfi delay-per-fragcommand to set the maximum time delay for transmitting a LFI  
fragment.  
MP-Group Interface view  
Virtual Template Interface view,  
ppp mp max-bind  
ppp mp min-bind  
Use the ppp mp max-bindcommand to configure maximum number of bound links of MP.  
Dialer Interface view  
Virtual Template Interface view  
Use the ppp mp min-bindcommand to configure the minimum number of PPP links that an MP bundle must  
have.  
Dialer Interface view  
ppp mp min-fragment  
ppp mp mp-group  
Use the ppp mp min-fragmentcommand to set minimum size of outgoing fragments.  
Virtual Template Interface view  
Interface view  
Use the ppp mp mp-groupcommand to add the current interface to the specified MP-group.  
ppp mp sort-buffer-size  
Use the ppp mp sort-buffer-sizecommand to set the size of the MP sort window.  
MP-Group Interface view  
Virtual Template Interface view  
ppp mp user  
Use the ppp mp usercommand to bind an MP user to a virtual template.  
System view  
ppp mp virtual-template  
Use the ppp mp virtual-templatecommand to configure the virtual template number to be bound by the  
interface.  
Interface view  
ppp pap local-user  
ppp timer negotiate  
Use the ppp pap local-usercommand to configure the username and password sent by the local router  
when it is authenticated by the peer router via the PAP method.  
Interface view  
Interface view  
Use the ppp timer negotiatecommand to set the PPP negotiation timeout.  
 
116  
3Com Router 5000/6000 Family  
Command Reference  
pppoe-client  
Use the pppoe-clientcommand to establish a PPPoE session and specify the Dialer Bundle  
corresponding to the session.  
Ethernet Interface (subinterface) view  
Virtual Ethernet Interface view  
pppoe-server bind virtual-template  
Use the pppoe-server bind virtual-templatecommand to enable PPPoE on the virtual-template  
specified by the Ethernet interface.  
Interface view  
System view  
System view  
System view  
System view  
pppoe-server log-information off  
Use the pppoe-server log-information offcommand to enable the PPPoE server to output the  
PPP-related log information.  
pppoe-server max-sessions local-mac  
Use the pppoe-server max-sessions local-maccommand to set the maximum number of PPPoE  
sessions that can be established at a local MAC address.  
pppoe-server max-sessions remote-mac  
Use the pppoe-server max-sessions remote-maccommand to set the maximum number of PPPoE  
sessions that can be established at a peer MAC address.  
pppoe-server max-sessions total  
Use the pppoe-server max-sessions totalcommand to set the maximum number of PPPoE sessions  
that the system can establish.  
pq  
Use the pqcommand to set the queue type of frame relay virtual circuit as Priority Queuing.  
Frame Relay Class view  
pre-shared-key  
Use the pre-shared-keycommand to set the pre-shared key used when a client needs to authenticate a  
DVPN server.  
Dvpn-Class view  
IKE-Peer view  
pre-shared-key  
preference  
Use the pre-shared-keycommand to configure a pre-shared key to be used in IKE negotiation.  
Use the preferencecommand to configure the preference of BGP protocol.  
BGP Protocol view  
BGP Multicast Address Family view  
preference  
preference  
preference  
preference clns  
pri-set  
Use the preferencecommand to configure the preference of IS-IS protocol.  
Use the preferencecommand to configure the preference of an OSPF protocol route.  
Use the preferencecommand to configure the route preference of RIP.  
IS-IS view  
OSPF view  
RIP view  
Use the preference clnscommand to set the preference of the CLNS routes discovered by IS-IS protocol.  
Use the pri-setcommand to bundle timeslots on the CT1/PRI or CE1/PRI interface into a pri-set.  
IS-IS view  
CE1/PRI Interface view  
CT1/PRI Interface view  
pri-set (CE1/PRI Interface)  
Use the pri-setcommand to have timeslots on the CE1/PRI interface form a pri-set.  
CE1/PRI Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
117  
pri-set (CT1/PRI Interface)  
Use the pri-setcommand to bundle the timeslots of the CT1/PRI interface into a pri-set.  
CT1/PRI Interface view  
primary accounting  
primary accounting  
Use the primary accountingcommand to configure IP address and port number of the primary RADIUS  
accounting server.  
RADIUS view  
Use the primary accounting command to configure a primary TACACS accounting server.  
TACACS+ view  
primary authentication  
Use the primary authenticationcommand to configure IP address and port number of the primary  
RADIUS authentication/authorization server.  
RADIUS view  
TACACS+ view  
TACACS+ view  
Voice Entity view  
Dvpn-Class view  
primary authentication  
Use the primary authenticationcommand to configure a primary TACACS authentication server.  
Use the primary authorizationcommand to configure a primary TACACS authorization server.  
Use the prioritycommand to configure the priority levels for voice entities.  
primary authorization  
priority  
private-ip  
Use the private-ip command to specify a private IP address of a specified DVPN server.  
private-line  
Use the private-linecommand to configure private auto-ring mode for the subscriber line and the E.164  
telephone number of the destination end.  
Voice Subscriber-Line view  
probe-failtimes  
Use the probe-failtimescommand to configure the number of consecutive probe failures allowed in an  
HWPing test before a trap is sent to the NMS.  
HWPing Test Group view  
process-config  
promiscuous  
proposal  
Use the process-configcommand to configure the dialing process of a certain access service number.  
Voice Access-Number view  
Use the promiscuouscommand to set the Ethernet interface to operate in promiscuous mode.  
Use the proposal command to set the proposal used by the IPSec policy.  
Ethernet Interface view  
IPSec Policy view  
IPSec Policy Template view  
protocol inbound  
Use the protocol inboundcommand to enable the current user interface to support Telnet, PAD, SSH, or  
all of them.  
VTY Interface view  
System view  
protocol-priority  
Use the protocol-prioritycommand to set a priority for a protocol globally.  
proxy  
Use the proxycommand to configure the IPv4 address and port number of the proxy server.  
Use the public-ip command to specify a public IP address of a specified DVPN server.  
SIP Client view  
Dvpn-Class view  
public-ip  
 
118  
3Com Router 5000/6000 Family  
Command Reference  
public-key-code begin  
Use the public-key-code begincommand to enter public key code view.  
Public Key view  
public-key-code end  
Use the public-key-code endcommand to return from public key code view to public key view and to save  
the configured public key.  
Public Key Code view  
put  
put  
pvc  
Use the putcommand to FTP a local file to the remote FTP server.  
FTP Client view  
Use the putcommand to upload a local file to the remote SFTP server.  
SFTP Client view  
Use the pvccommand to create a PVC or enter the PVC view at ATM interface or in PVC-Group view.  
ATM Interface view  
PVC-Group view  
pvc-group  
pvc max-number  
pvc-pq  
Use the pvc-groupcommand to create a PVC-Group or enter the PVC-Group view at ATM interface.  
Use the pvc max-numbercommand to set the maximum number of ATM interface virtual circuits (VC).  
ATM Interface view  
ATM Master Interface view  
Use the pvc-pqcommand to set the type of the PVC PQ that packets sent by frame relay virtual circuit enter.  
Frame Relay Class view  
ATM Pvc-Group view  
Interface view  
pvc-protect  
pvp create  
pvp limit  
pwd  
Use the pvc-protectcommand to configure the protection mode for a PVC in a PVC group.  
Use the pvp createcommand to create a virtual path.  
Use the pvp limitcommand to set the parameters for VP policing.  
Use the pwdcommand to view the working directory on the remote FTP server.  
Use the pwdcommand to display the current directory on the SFTP server.  
Use the pwdcommand, you can view the current path.  
ATM Master Interface view  
FTP Client view  
pwd  
SFTP Client view  
User view  
pwd  
qmtoken  
queue af  
Use the qmtokencommand to configure the number of transmitted tokens.  
Interface view  
Use the queue afcommand to configure the class to perform the assured-forwarding and the minimum  
bandwidth used.  
Traffic Behavior view  
queue ef  
Use the queue efcommand to configure expedited-forwarding packets to the absolute priority queue and  
configure the maximum bandwidth.  
Traffic Behavior view  
queue-length  
Use the queue-lengthcommand to configure maximum queue length.  
Traffic Behavior view  
 
3Com Router 5000/6000 Family  
Command Reference  
119  
queue wfq  
Use the queue wfqcommand to configure the default-class to use WFQ.  
Traffic Behavior view  
quit  
Use the quitcommand to return from current view to lower level view, or exit the system if current view is  
user view.  
Any view  
quit  
quit  
Use the quitcommand to disconnect from the remote FTP server and exit to user view.  
FTP Client view  
Use the quitcommand to terminate the connection to the remote SFTP server and exit to system view as  
you would with the byeand exitcommands.  
SFTP Client view  
User view  
quit  
Use the quitcommand to terminate the connection to the remote SSH server.  
Use the qos apply policycommand to apply a service policy to the interface.  
Use the qos carcommand to implement TP policy on an interface.  
Use the qos carlcommand to establish or modify a CARL.  
qos apply policy  
Interface view  
Interface view  
System view  
Interface view  
qos car  
qos carl  
qos cq  
Use the qos cq cqlcommand to apply the customized queue to an interface.  
qos cql default-queue  
Use the qos cql default-queuecommand to assign a default queue for those packets that do not match  
any rule in the CQL.  
System view  
System view  
System view  
qos cql inbound-interface  
Use the qos cql inbound-interfacecommand to establish classification rules based on interfaces.  
qos cql protocol  
Use the qos cql protocolcommand to establish classification rules based on the protocol type.  
qos cql protocol mpls exp  
Use the qos cql protocol mpls exp command to configure classification rule based on the MPLS  
protocol.  
System view  
System view  
qos cql queue  
Use the qos cql queuecommand to configure the length of a queue, namely, the number of packets a  
queue can hold.  
qos cql queue serving  
Use the qos cql queue servingcommand to set the byte-count of the packets sent from a given queue in  
each poll.  
System view  
Interface view  
qos fifo queue-length  
Use the qos fifo queue-lengthcommand to set the length limit of FIFO queue.  
qos gts  
Use the qos gtscommand to set shaping parameters for all or a specified type of traffic and perform traffic  
shaping.  
Interface view  
 
120  
3Com Router 5000/6000 Family  
Command Reference  
qos lr  
Use the qos lrcommand to limit the transmitting rate of the interface.  
Interface (including the MFR Interface) view  
qos max-bandwidth  
Use the qos max-bandwidthcommand to configure the maximum interface bandwidth used when CBQ  
enqueues packets.  
Interface view  
System view  
Interface view  
qos policy  
Use the qos policycommand to define a policy and enter policy view.  
Use the qos pqcommand to apply a group of priority list to an interface.  
qos pq  
qos pql default-queue  
Use the qos pql default-queuecommand to designate the packets without corresponding rules to a  
default queue.  
System view  
System view  
System view  
qos pql inbound-interface  
Use the qos pql inbound-interfacecommand to establish classification rules based on interfaces.  
qos pql protocol  
qos pql queue  
Use the qos pql inbound-interfacecommand to establish classification rules based on interfaces.  
Use the qos pql queuecommand to specify the maximum number of packets that can wait in each of the  
priority queues, or the length of a PQ.  
System view  
System view  
Interface view  
qos pql protocol mpls exp  
Use the qos pql protocol mpls expcommand to establish the classification rule based on MPLS protocol.  
qos reserved-bandwidth  
Use the qos reserved-bandwidthcommand to set the maximum reserved bandwidth percentage.  
qos rtpq  
Use the qos rtpqcommand to enable RTP queue feature on an interface so as to reserve a real-time  
service for the RTP packets sent to some UDP destination port ranges.  
Interface view  
qos wfq  
Use the qos wfq command to apply WFQ to and configure WFQ parameters on the interface or modify  
WFQ parameters on the interface.  
Interface view  
Interface view  
qos wred  
Use the qos wredcommand to apply WRED at an interface.  
qos wred dscp  
Use the qos wred dscp command to set the lower limit, upper limit, and drop probability denominator of a  
WRED DSCP.  
Interface view  
Interface view  
qos wred ip-precedence  
Use the qos wred ip-precedencecommand to configure the minimum threshold, maximum threshold and  
drop probability denominator for each precedence level in WRED.  
qos wred weighting-constant  
Use the qos wred weighting-constantcommand to set exponential used to calculate the average length  
of WRED queues.  
Interface view  
System view  
radius nas-ip  
Use the radius nas-ipcommand to specify the source address of the RADIUS packet sent from NAS.  
 
3Com Router 5000/6000 Family  
Command Reference  
121  
radius scheme  
Use the radius schemecommand to configure a RADIUS scheme and enter its view.  
System view  
System view  
radius trap  
ras-on  
Use the radius trapcommand to enable the RADIUS server to send traps when it goes down.  
Use the ras-oncommand to enable the GK Client function.  
Voice GK Client view  
R2 CAS view  
re-answer  
Use the re-answercommand to enable or disable the originating point to support re-answer signal process.  
Use the re-authenticationcommand to enable console login re-authentication.  
Use the rebootcommand to have the router reboot.  
re-authentication  
User Interface view  
User view  
reboot  
receive gain  
redialtimes  
Use the receive gaincommand to configure the gain value at the voice subscriber-line input end.  
Voice Subscriber-Line view  
Use the redialtimescommand to configure the number of times of dialing in each dialing phase for a  
certain access service number.  
Voice Access-Number view  
redirect bind vpn-instance  
Use the redirect bind vpn-instancecommand to bind a VPN instance to the user interface.  
User Interface view  
redirect disconnect  
redirect enable  
Use the redirect disconnectcommand to disconnect a redirected telnet connection manually.  
Use the redirect enablecommand to enable redirect on the asynchronous serial interface.  
User Interface view  
User Interface view  
redirect listen-port  
Use the redirect listen-portcommand to specify a port to listen for redirected Telnet connections.  
User Interface view  
User Interface view  
User Interface view  
redirect refuse-negotiation  
Use the redirect refuse-negotiationcommand to disable Telnet option negotiation during setup of  
redirected Telnet connection.  
redirect return-deal from-telnet  
Use the redirect return-deal from-telnetcommand to have the router that redirects Telnet connection  
substitute 0x0d for 0x0d 0x0a and 0x0d 0x00, the carriage returns received from the Telnet client.  
redirect return-deal from-terminal  
Use the redirect return-deal from-terminalcommand to have the router that redirects Telnet  
connection substitute 0x0d for 0x0d 0x0a and 0x0d 0x00, the carriage returns received from the terminal (a  
PC connected to the console port for example).  
User Interface view  
User Interface view  
redirect timeout  
Use the redirect timeoutcommand to specify the amount of time that a redirected Telnet connection can  
stay idle. After that, the connection is disconnected.  
reflect between-clients  
Use the reflect between-clientscommand to enable route reflection between clients.  
BGP view  
VPNv4 view  
VPN Instance view  
 
122  
3Com Router 5000/6000 Family  
Command Reference  
reflector cluster-id  
Use the reflector cluster-idcommand to configure the cluster ID of the route reflector.  
BGP Unicast view  
BGP Multicast view  
VPNv4 view  
refresh bgp  
Use the refresh bgp command to request the peer to retransmit routes or retransmit routes to the peer.  
Use the register-enablecommand to enable or disable the SIP registration function.  
Use the register lifetimecommand to configure the registration lifetime of an MR.  
User view  
SIP Client view  
MR view  
register-enable  
register lifetime  
register-number  
Use the register-numbercommand to enable the gateway (the VoIP-enabled router) to register the  
number of the voice entity with the H.323 gatekeeper or SIP server.  
Voice Entity view  
PIM view  
register-policy  
Use the register-policycommand to configure a RP to filter the register packet sent by the DR in the  
PIM-SM network and to accept the specific packet only.  
register retransmit  
Use the register retransmitcommand to configure the registration retransmission parameters of an MR,  
including the initial registration retransmission interval, the maximum registration retransmission interval,  
and the maximum number of registration retransmission attempts.  
MR view  
register-value  
registrar  
Use the register-valuecommand to configure the value of all register signals of R2 signaling.  
R2 CAS view  
Use the registrarcommand to configure the IP address or domain name, port number, timeout time as  
well as master/slave attribute of the registration server under UAs.  
SIP Client view  
Traffic Behavior view  
Traffic Behavior view  
Traffic Behavior view  
Traffic Behavior view  
Traffic Behavior view  
Traffic Behavior view  
IKE-Peer view  
remark atmclp  
remark dot1p  
Use the remark atmclpcommand to have the system remark the CLP bit of ATM packets in the class.  
Use the remark dot1pcommand to configure the 802.1p priority value in the VLAN packets of a class.  
Use the remark dscpcommand to set a remarked DSCP value for IP packets belonging to the class.  
Use the remark fr-decommand to set the remarked DE bit of frame relay packets.  
Use the remark ip-precedencecommand to configure IP precedence remark.  
remark dsc  
remark fr-de  
remark ip-precedence  
remark mpls-exp  
remote-address  
remote address  
Use the remark mpls-expcommand to configure MPLS EXP value to identify matched packets.  
Use the remote-addresscommand to configure IP address of the remote GW.  
Use the remote addresscommand to configure to assign IP address for the peer interface.  
 
Interface view  
3Com Router 5000/6000 Family  
Command Reference  
123  
remote-ip  
Use the remote-ipcommand to configure a remote IP address. The address should be the LSR ID of the  
remote LSR. As remote peers adopt LSR ID as their transport addresses, the last two remote peers use  
their LSR ID as their transport addresses for creating TCP connection.  
Remote-Peer view  
IKE-Peer view  
remote-name  
remotehelp  
remove  
Use the remote-namecommand to specify a name for the remote GW.  
Use the remotehelpcommand to view the help for the FTP commands.  
FTP Client view  
Use the removecommand to delete the specified file from the server as you would with the delete  
command.  
SFTP Client view  
remove slot  
Use the remove slotcommand to have the system do some pre-processing work before removing an  
interface card.  
User view  
FTP Client view  
SFTP Client view  
User view  
rename  
Use the renamecommand to rename a file on the FTP server from the FTP client.  
Use the renamecommand to change the name of the specified file on the SFTP server.  
Use the renamecommand to rename a file.  
rename  
rename  
renew  
Use the renewcommand to configure the signal values of C bit and D bit.  
Use the resetcommand to reset the system parameters of RIP.  
R2 CAS view  
RIP view  
reset  
reset acl counter  
reset alarm urgent  
reset l2tp session  
Use the reset acl countercommand to clear the statistics of access control list  
Use the reset alarm urgentwcommand to clear all the stored alarms.  
User View  
User view  
Use the reset l2tp session command to disconnect a session. When the user calls in, the session can  
be set up again.  
User view  
reset l2tp tunnel  
Use the reset l2tp tunnelcommand to clear the specified tunnel connection and all sessions on the  
tunnel.  
User view  
User view  
User view  
reset l2tp user  
reset arp  
Use the reset l2tp usercommand to disconnect the L2TP connection of the specified user.  
Use the reset arpcommand to clear the ARP entries in the ARP mapping table.  
reset atm  
Use the reset atmcommand to clear statistics about all PVCs on the specified ATM interface, excluding  
statistics about the ATM interface.  
User view  
 
124  
3Com Router 5000/6000 Family  
Command Reference  
reset bgp  
Use the reset bgppeer-addresscommand to reset the connection of BGP with a specified peer.  
User view  
User view  
reset bgp flap-info  
reset bgp group  
Use the reset bgp flap-infocommand to reset the flap statistics of routes.  
Use the reset bgp groupcommand to reset the BGP connections of all the members in the specified peer  
group.  
User view  
reset bridge address-table  
Use the reset bridgecommand to clear all the dynamic address entries or the entries of a specified bridge  
set or a specified interface in the forwarding table.  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
reset bridge traffic  
reset clns statistics  
Use the reset bridge trafficcommand to clear the traffic statistics of a bridge set on a interface.  
Use the reset clns statisticscommand to reset statistics information about CLNS flow.  
reset counters controller e1  
Use the reset counters controller e1command to clear the controller counter for the CE1/PRI interface.  
reset counters controller t1  
Use the reset counters controller t1command to clear the controller counter for the CT1/PRI interface.  
reset counters encrypt  
Use the reset counters interface encryptcommand to clear the statistics on the encryption card.  
reset counters interface  
Use the reset counters interfacecommand to reset the statistics about the port.  
reset counters interface  
Use the reset counters interfacecommand to clear statistics about the transmitted and received  
packets, IP, ARP, and ICMP on the specified interface or all interfaces.  
User view  
User view  
reset dampening  
Use the reset dampeningcommand to clear the dampening information and flap statistics of a route and  
release the suppression of a suppressed route.  
reset dhcp ip-in-use  
Use the reset dhcp server ip-in-usecommand to clear the DHCP dynamic address binding information,  
outdated or not.  
User view  
User view  
User view  
reset dhcp relay statistics  
Use the reset dhcp relay statisticscommand to clear the DHCP relay statistics.  
reset dhcp server conflict  
Use the reset dhcp server conflictcommand to clear the statistics about DHCP address collision.  
reset dhcp server statistics  
Use the reset dhcp server statisticscommand to clear the statistics on the DHCP server, including  
such information as number of DHCP address pools, automatically and manually bound addresses and  
expired addresses, number of unknown packets, number of DHCP request packets, and number of  
response packets.  
User view  
 
3Com Router 5000/6000 Family  
Command Reference  
125  
reset dlsw bridge-entry  
Use the reset dlsw bridge-entrycommand to clear the entry cache information in the DLSw bridge  
group.  
User view  
User view  
reset dlsw circuits  
Use the reset dlsw circuitscommand to clear the DLSw virtual circuit information.  
reset dlsw ethernet-backup circuit  
Use the reset dlsw ethernet-backup circuitcommand to clear information about all circuits that the  
router and its neighbors have established with the remote peers since DLSw Ethernet redundancy is  
enabled.  
User view  
User view  
User view  
reset dlsw ethernet-backup map  
Use the reset dlsw ethernet-backup mapcommand to clear the MAC address map of the Ethernet switch  
support feature.  
reset dlsw reachable-cache  
Use the reset dlsw reachable-cachecommand to clear information from the reachable-cache of the  
DLSw.  
reset dlsw tcp  
Use the reset dlsw tcpcommand to reestablish or delete all connection to all the remote peers.  
Use the reset dlsw tcp ip-address command to reestablish a TCP connection or delete the connection  
to the specified remote peer.  
User view  
User view  
reset dns dynamic-host  
Use the reset dns dynamic-hostcommand to clear the current contents in the domain name cache of the  
DNS client.  
reset dvpn all  
Use the reset dvpn all command to clear all operating information about a specified DVPN domain and  
to initiate the DVPN domain.  
User view  
User view  
User view  
User view  
User view  
reset dvpn map  
Use the reset dvpn mapcommand to clear a specified map.  
reset dvpn session  
reset dvpn statistics  
reset encrypt-card sa  
Use the reset dvpn sessioncommand to clear a specified session.  
Use the reset dvpn statisticscommand to clear all the statistics information of a DVPN module.  
Use the reset encrypt-card sacommand to clear the SAs on the encryption card.  
reset encrypt-card statistics  
Use the reset encrypt-card statisticscommand to clear the statistics during processing of the  
encryption card.  
User view  
User view  
User view  
reset encrypt-card syslog  
Use the reset encrypt-card syslogcommand to clear all the logging information on the encryption card.  
Use the reset esis statisticscommand to reset statistics information about ES-IS flow.  
reset esis statistics  
reset fcm  
Use the reset fcmcommand to clear the dial-up negotiation failure counter and the timeout disconnection  
counter for each FCM interface.  
User view  
 
126  
3Com Router 5000/6000 Family  
Command Reference  
reset firewall ethernet-frame-filter  
reset firewall-statistics  
Use the reset firewall ethernet-frame-filtercommand to clear the ACL-based firewall statistics.  
User view  
User view  
User view  
Use the reset firewall-statisticscommand to clear the firewall statistics.  
reset fr inarp  
Use the reset fr inarpcommand to clear the address mapping established by inverse ARP.  
reset hwatacs statistics  
Use the reset hwtacacs statisticscommand to clear TACACS+ protocol statistics.reset hwtacacs  
statistics  
User view  
reset igmp group  
Use the reset igmp groupcommand to delete the IGMP group joined on the interface. The deletion of the  
group does not affect its joining again.  
User view  
User view  
User view  
User view  
reset ike sa  
Use the reset ike sacommand to delete the security tunnel set up by IKE.  
reset ip count  
Use the reset ip countcommand to clear information that the IP Accounting retained about IP packets.  
reset ip fast-forwarding cache  
Use the reset ip fast-forwarding cachecommand to reset the unicast fast forwarding cache.  
reset ip multicast-fast-forwarding cache  
Use the reset ip multicast-fast-forwarding cachecommand to clear the multicast fast forwarding  
cache. However, this command does not release the space occupied by the cache.  
User view  
reset ip netstream statistics  
Use the reset ip netstream statisticscommand to age and export all stream statistics to clear the  
NetStream cache.  
User view  
User view  
reset ip routing-table  
Use the reset ip routing-tablecommand to clear the routing table.  
reset ip statistics  
Use the reset ip statisticscommand to clear the IP statistics information. In some special cases, it is  
necessary to clear the IP statistics information and perform new statistics.  
User view  
User view  
User view  
reset ipsec sa  
Use the reset ipsec sacommand to delete an SA already set up (manually or through IKE negotiation).  
If no parameter (remote, policy, parameters) is specified, all the SA will be deleted.  
reset ipsec statistics  
Use the reset ipsec statisticscommand to clear IPSec message statistics, and set all the statistics to  
zero.  
reset ipx routing-table statistics  
The reset ipx routing-table statisticscommand is used to clear the statistical information of a  
specified type of IPX route.  
User view  
User view  
User view  
reset ipx statistics  
reset isis all  
Use the reset ipx statisticscommand to clear IPX statistics by the system.  
Use the reset isis allcommand to reset all the IS-IS data.  
 
3Com Router 5000/6000 Family  
Command Reference  
127  
reset isis peer  
Use the reset isis peercommand to reset the IS-IS data of specified IS-IS neighbor.  
User view  
reset lapb  
Use the reset lapb statisticscommand to clear the statistics about LAPB.  
Interface view  
reset loadsharing  
Use the reset loadsharing command to reset statistics about unbalanced load sharing for all interfaces  
or the interfaces related to the equal-cost routes to the specified destination network.  
User view  
User view  
reset logbuffer  
Use the reset logbuffercommand to clear information in the log buffer.  
reset mobile-ip binding  
Use the reset mobile-ip bindingcommand to remove mobility bindings. With neither the ip-address  
argument nor the interface-number argument specified, all mobility bindings are removed.  
User view  
reset mobile-ip mobile-router  
Use the reset mobile-ip mobile-router agentcommand to clear agent information discovered by the  
MR, MR registration information, and MR statistics.  
User view  
User view  
User view  
reset mobile-ip node-statistics  
Use the reset mobile-ip node-statisticscommand to clear MN statistics.  
reset mobile-ip statistics  
Use the reset mobile-ip statisticscommand to clear all MIP counters.  
reset mobile-ip visitor  
Use the reset mobile-ip visitorcommand to delete information in the visitor table and the pending table  
on the FA, or with the pending keyword specified to delete information in the pending table only. You can  
also restrict deletion to one MN or MNs registered on an interface by specifying arguments ip-address  
and interface ethernet interface-numberrespectively.  
User view  
reset mpls cell-transfer interface  
Use the reset mpls cell-transfer interfacecommand to reset statistics for the cells received/sent in  
a packet on an interface in transparent transmission mode.  
Any view  
User view  
reset mpls statistics  
Use the reset mpls statisticscommand to clear MPLS statistics.  
reset msdp peer  
Use the reset msdp peercommand to reset TCP connection with the specified MSDP peer, and clear all  
the statistics of the specified MSDP peer.  
User view  
User view  
reset msdp sa-cache  
Use the reset msdp sa-cachecommand to clear SMDP SA cache entries.  
reset msdp statistics  
Use the reset msdp statisticscommand to clear statistics of one or more MSDP peers without resetting  
the MSDP peer.  
User view  
User view  
User view  
reset multicast forwarding-table  
Use the reset multicast forwarding-tablecommand to clear MFC forwarding entries or the statistics  
of MFC forwarding entries.  
reset multicast routing-table  
Use the reset multicast routing-tablecommand to clear the route entry in the multicast kernel routing  
table and remove the corresponding forwarding entry in MFC.  
 
128  
3Com Router 5000/6000 Family  
Command Reference  
reset nat  
Use the reset natcommand to clear up the mapping tables of address translation in the memory and  
release all the memory dynamically allocated to store the mapping tables.  
User view  
reset ospf  
Use the reset ospf allcommand to reset all the OSPF processes. Use the parameter of statistics to reset  
statistics about OSPF.  
Use the reset ospfcommand to reset the OSPF process, the following results are expected:  
User view  
User view  
User view  
User view  
reset pim neighbor  
Use the reset pim neighborcommand to clear PIM neighbor.  
reset pim routing-table  
Use the reset pim routing-tablecommand to clear PIM route entry.  
reset portal  
reset pos  
Use the reset portalcommand to clear the related portal statistics.  
Use the reset poscommand to clear the counters for POS applications and POS access ports, that is, the  
information displayed with the display pos-appand display pos-interfacecommands.  
User view  
reset ppp compression iphc  
Use the reset ppp compression iphccommand to delete the invalid IP/UDP/RTP header compression or  
decompression context storage table and clear statistic information of IP/UDP/RTP header compression.  
User view  
User view  
User view  
User view  
reset ppp compression stac-lzs  
Use the reset ppp compression stac-lzscommand to clear statistics about STAC-LZS compression.  
Use the reset pppoe-clientcommand to terminate PPPoE session and re-initiate the connection later.  
Use the reset pppoe-servercommand to clear PPPoE sessions at the server end.  
reset pppoe-client  
reset pppoe-server  
reset radius statistics  
Use the reset radius statisticscommand to clear the statistic information related to the RADIUS  
protocol.  
User view  
User view  
reset recycle-bin  
Use the reset recycle-bincommand to delete one or files from the recycle bin completely.  
reset saved-configuration  
Use the reset saved-configurationcommand to delete the configuration file loaded at this startup from  
the Flash.  
User view  
reset stop-accounting-buffer  
Use the reset stop-accounting-buffercommand to clear the buffered stop-accounting requests that  
have no responses.  
System view  
reset stop-accounting-buffer  
Use the reset stop-accounting-buffercommand to clear the stop-accounting requests that have no  
response and are buffered on the router.  
User view  
User view  
reset stp statistics  
Use the reset stp statisticscommand to clear statistics about the spanning tree.  
 
3Com Router 5000/6000 Family  
Command Reference  
129  
reset tcp statistics  
Use the reset tcp statisticscommand to clear TCP traffic statistic information. After the execution of  
this command, there’s no prompt information on the screen, and the existing statistics are cleared.  
User view  
User view  
reset trapbuffer  
Use the reset trapbuffercommand to clear information in the trap buffer.  
reset udp statistics  
Use the reset udp statistics command to clear the UDP statistics information. After the execution of  
this command, there’s no prompt information on the screen, and the existing statistics are cleared.  
User view  
User view  
reset vlan statistics vid  
Use the reset vlan statistics vidcommand to clear the VLAN statistics.  
reset voice call-history-record line  
Use the reset voice call-history-record linecommand to clear the call history of all voice subscriber  
lines, or information displayed by the display voice call-history-record linecommand.  
Use the reset voice emcommand to reset the call statistics on the digital E&M interface.  
Use the reset voice faxcommand to reset fax statistics.  
User view  
User view  
User view  
reset voice em  
reset voice fax  
reset voice fax trans-statistics  
Use the reset voice fax trans-statistics command to reset the statistics for the FAX transform  
module.  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
User view  
reset voice ipp  
reset voice r2  
reset voice rcv  
reset voice sip  
reset voice vcc  
Use the reset voice ippcommand to reset IPP statistics.  
Use the reset voice r2command to reset the call statistics of R2 signaling.  
Use the reset voice rcvcommand to reset RCV statistics.  
Use the reset voice sipcommand to reset all the statistic information about the SIP client.  
Use the reset voice vcccommand to reset the information related to VCC.  
reset voice voip data-statistics  
Use the reset voice voip data-statisticcommand to reset statistics information of voice data.  
reset voice vpp  
Use the reset voice vppcommand to reset VPP statistics.  
reset web java-blocking counter  
Use the reset web java-blocking countercommand to clear the Java blocking statistics information.  
reset web log-buf  
Use the reset web log-bufcommand to clear the web filtering log buffer.  
reset web url-filter host counter  
Use the reset web url-filter host countercommand to clear the URL address filtering statistics  
information.  
User view  
 
130  
3Com Router 5000/6000 Family  
Command Reference  
reset web url-filter parameter counter  
Use the reset web url-filter parameter countercommand to clear the statistics of SQL injection attack  
protection.  
User view  
reset x25  
reset xot  
Use the reset x25command to reset statistics about X.25 on the specified interface or to reset the specified  
X.25 VC.  
User view  
For SVC, use the reset xotcommand to initiatively clear an XOT link.  
For PVC, use the reset xotcommand to initiatively reset an XOT link.  
User view  
Interface view  
restart  
retry  
Use the restartcommand to reset the physical interface.  
Use the retrycommand to set the maximum number of probing retries during an auto detect interval.  
Use the retrycommand to configure the number of RADIUS request attempts.  
Detect Group view  
RADIUS view  
retry  
retry realtime-accounting  
Use the retry realtime-accountingcommand to configure the maximum number of real-time accounting  
request attempts allowed to have no responses.  
RADIUS view  
RADIUS view  
TACACS+ view  
retry stop-accounting  
Use the retry stop-accountingcommand to configure the maximal retransmission times after  
stop-accounting request.  
retry stop-accounting  
Use the retry stop-accountingcommand to enable stop-accounting packet retransmission and configure  
the maximum number of stop-accounting request attempts.  
return  
Use the returncommand to return to user view from any other view.  
All views except User view  
R2 CAS view  
reverse  
Use the reversecommand to configure the inversion mode of line signals.  
Use the reverse-rtscommand to reverse RTS signal.  
reverse-rts  
reverse-tunnel  
ring-generate  
Synchronous Serial Interface view  
MR view  
Use the reverse-tunnelcommand to enable the reverse tunneling function for an MR.  
Use the ring-generatecommand to configure the gateway at the called side to give a ringback tone when  
in quick start mode.  
Voice Subscriber-Line view  
rip  
Use the ripcommand to enable the RIP and enter the RIP view.  
System view  
rip authentication-mode  
Use the rip authentication-modecommand to configure RIP-2 authentication mode and corresponding  
parameters.  
Interface view  
Interface view  
rip input  
Use the rip inputcommand to allow an interface to receive RIP packets.  
 
3Com Router 5000/6000 Family  
Command Reference  
131  
rip metricin  
Use the rip metricincommand to configure the additional route metric added to the route when an  
interface receives RIP packets.  
Interface view  
rip metricout  
Use the rip metricoutvaluecommand to enable RIP to send routes out the interface with an additional  
route metric added. This command applies to routes both locally learned and learned from other routers.  
Use the rip metricoutvalueall-routecommand to enable RIP to send routes out the interface with an  
additional route metric added. This command applies to locally redistributed routes in addition to those  
locally learned and learned from other routers.  
Interface view  
Interface view  
rip output  
Use the rip outputcommand to configure an interface to transmit RIP packets to the external.  
rip split-horizon  
Use the rip split-horizoncommand to configure an interface to use split horizon when transmitting RIP  
packets.  
Interface view  
Interface view  
Interface view  
Interface view  
User view  
rip triggered  
rip version  
rip work  
rlogin  
Use the rip triggeredcommand to enable trigger RIP (TRIP).  
Use the rip versioncommand to configure the version of RIP packets on an interface.  
Use the rip workcommand to enable the running of RIP on an interface.  
Use the rlogincommand to rlogin onto the specified remote host with the specified user name.  
Use the rmdircommand to delete a specified directory from the FTP server.  
Use the rmdircommand to delete the specified directory from the remote SFTP server.  
Use the rmdircommand to delete a directory.  
rmdir  
FTP Client view  
SFTP Client view  
User view  
rmdir  
rmdir  
rmon alarm  
Use the rmon alarmcommand to set an alarm entry. When an exception occurs, the alarm is triggered. The  
alarm in turn triggers the corresponding event, which can be log, trap, or log-and-trap.  
System view  
System view  
rmon event  
Use the rmon eventcommand to add an event entry.  
rmon history  
rmon prialarm  
rmon statistics  
Use the rmon historycommand to add a history control entry.  
Ethernet Interface view  
System view  
Use the rmon prialarmcommand to add an entry to the prialarm table.  
Use the rmon statisticscommand to add a statistics entry.  
Ethernet Interface view  
root-certificate fingerprint  
Use the root-certificate fingerprintcommand to configure the fingerprint for authenticating the CA  
root certificate.  
PKI Domain view  
 
132  
3Com Router 5000/6000 Family  
Command Reference  
route-distinguisher  
Use the route-distinguishercommand to configure RD for an MPLS VPN instance. A vpn-instance  
cannot run until it is configured with an RD.  
MBGP VPN-Instance view  
route-policy  
Use the route-policycommand to create a route-policy or a route-policy node and enter the corresponding  
view.  
System view  
System view  
route-policy  
route-tag  
Use the route-policycommand to configure a route-policy node and enter the route-policy view.  
Use the route-tagcommand to specify a tag value to identify VPN import route.  
OSPF Protocol view  
routed-bridge protocol  
Use the routed-bridge protocolcommand to enable the support of routed bridge encapsulation to a  
network protocol.  
ATM PVC view  
System view  
router id  
Use the router idcommand to configure the ID of a router running the OSPF protocol.  
routing-table limit  
Use the routing-table limit command to limit the route maximum in a vpn-instance, to avoid too many  
routes in the ingress interface of the PE router.  
MBGP VPN-Instance view  
System view  
rsa local-key-pair create  
Use the rsa local-key-pair createcommand to generate the local RSA host key pair and server key  
pair.  
rsa local-key-pair destroy  
Use the rsa local-key-pair destroycommand to remove all RSA keys on the server (including the host  
key pair and the server key pair).  
System view  
rsa peer-public-key  
Use the rsa peer-public-keycommand to enter public key view. After that, you may use the  
public-key-code begincommand and the public-key-code endcommand to configure the public key of  
the client.  
System view  
User View  
rsh  
Use the rshcommand to execute a command on a remote host remotely.  
rtpq  
Use the rtpqcommand to configure to apply Realtime Transport Protocol (RTP) Priority Queuing.  
Frame Relay Class view  
ACL view  
rule  
Use the rulecommand to add a rule in current ACL view.  
rule  
Use the rulecommand to configure the number-substitute rules.  
Voice Number-Substitute view  
sa authentication-hex  
Use the sa authentication-hexcommand to set the SA authentication key manually for the ipsec policy  
of manual mode.  
Manually-Established IPSec Policy view  
sa duration  
Use the sa durationcommand to specify the ISAKMP Sa duration for an IKE proposal.  
IKE Proposal view  
 
3Com Router 5000/6000 Family  
Command Reference  
133  
sa duration  
Use the sa durationcommand to set a SA duration of the ipsec policy.  
IPSec Policy view  
IPSec Policy Template view  
sa encryption-hex  
Use the sa encryption-hexcommand to set the SA encryption key manually for the ipsec policy of manual  
mode.  
Manually-Established IPSec Policy view  
sa spi  
Use the sa spicommand to set the SA SPI manually for the ipsec policy of manual mode.  
Manually-Established IPSec Policy view  
sa string-key  
Use the sa string-keycommand to set the SA parameter manually for the ipsec policy of manual mode.  
Manually-Established IPSec Policy view  
save  
Use the savecommand to save the current configuration file to the storage device.  
Any view  
schedule reboot at  
Use the schedule reboot atcommand to enable the scheduled reboot function of the router and schedule  
the reboot time and date.  
User view  
User view  
schedule reboot delay  
Use the schedule reboot delaycommand to enable scheduled router reboot and set the waiting time.  
Use the schemecommand to configure the AAA scheme to be referenced by the current ISP domain.  
scheme  
ISP Domain view  
scramble  
Use the scramblecommand to enable an undo scrambleto scramble the payload on ATM OC-3c/STM-1  
interface.  
ATM Interface view  
scramble  
Use the scramblecommand to enable payload scrambling on the ATM E1/T1 interface. This, however,  
does not affect cell headers.  
ATM E1/T1 Interface view  
ATM E3/T3 Interface view  
POS Interface view  
scramble  
Use the scramblecommand to enable scrambling function of ATM E3/T3 interface.  
Use the scramblecommand to enable the POS interface to scramble payload data.  
Use the screen-lengthcommand to set the number of lines displayed on the terminal screen.  
scramble  
screen-length  
screen-width  
User Interface view  
Use the screen-widthcommand to set the width of the terminal screen, that is, how many characters can  
be displayed in one line.  
User interface view  
System view  
script-string  
Use the script-stringcommand to configure a Modem script.  
script trigger connect  
Use the script trigger connectcommand to configure the Modem script that will be executed once an  
incoming call connection is established.  
User Interface view  
User Interface view  
script trigger dial  
Use the script trigger dialcommand to configure the Modem script that is used for DCC dialing.  
 
134  
3Com Router 5000/6000 Family  
Command Reference  
script trigger init  
Use the script trigger initcommand to configure the Modem script that will be executed when the  
system is powered on or rebooted.  
User Interface view  
User Interface view  
User-interface view  
script trigger login  
Use the script trigger login command to configure the Modem script that will be executed when an  
outgoing call connection is successfully established.  
script trigger logout  
Use the script trigger logoutcommand to configure the Modem script that is executed when a link is  
reset.  
sdlc controller  
Use the sdlc controllercommand to configure the secondary station address of the SDLC.  
Synchronous Serial Interface view  
Synchronous Serial Interface view  
Synchronous Serial Interface view  
sdlc mac-map local  
sdlc mac-map remote  
sdlc max-pdu  
Use the sdlc mac-map localcommand to configure the virtual MAC address of the SDLC.  
Use the sdlc mac-map remotecommand to configure the SDLC peer.  
Use the sdlc max-pducommand to configure the maximum receivable frame length of the SDLC.  
Synchronous Serial Interface view  
sdlc max-send-queue  
sdlc max-transmission  
sdlc modulo  
Use the sdlc max-send-queuecommand to configure the queue length sending the SDLC packet.  
Synchronous Serial Interface view  
Use the sdlc max-transmissioncommand to configure the SDLC timeout retransmission times.  
Synchronous Serial Interface view  
Use the sdlc modulocommand to configure the modulus of the SDLC.  
Synchronous Serial Interface view  
sdlc sap-map local  
Use the sdlc sap-map localcommand to configure the SAP address on transforming the SDLC into the  
LLC2.  
Synchronous Serial Interface view  
sdlc sap-map remote  
sdlc simultaneous  
Use the sdlc sap-map remote command to configure the remote DLSw device SAP address when SDLC  
is translated into LLC2.  
Synchronous Serial Interface view  
Use the sdlc simultaneouscommand to configure the SDLC data to use the bidirectional transmission  
mode.  
Synchronous Serial Interface view  
sdlc status  
Use the sdlc rolecommand to configure the SDLC role the device acts.  
Synchronous Serial Interface view  
sdlc timer ack  
Use the sdlc timer ackcommand to configure the SDLC primary station response waiting time  
(mseconds).  
Synchronous Serial Interface view  
sdlc timer lifetime  
Use the sdlc timer lifetimecommand to configure the SDLC secondary station response waiting time  
(mseconds).  
Synchronous Serial Interface view  
sdlc timer poll  
Use the sdlc timer pollcommand to configure the SDLC poll pause timer.  
Synchronous Serial Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
135  
sdlc window  
Use the sdlc windowcommand to configure the length of the SDLC local response window.  
Synchronous Serial Interface view  
Synchronous Serial Interface view  
sdlc xid  
Use the sdlc xidcommand to configure the XID of the SDLC.  
secondary accounting  
Use the secondary accountingcommand to configure the IP address and port number for the secondary  
RADIUS accounting server.  
RADIUS view  
secondary accounting  
Use the secondary accountingcommand to configure a secondary TACACS accounting server.  
TACACS+ view  
secondary authentication  
Use the secondary authenticationcommand to configure the IP address and port number of the  
secondary RADIUS authentication/authorization/accounting server.  
RADIUS view  
TACACS+ view  
TACACS+ view  
secondary authentication  
Use the secondary authenticationcommand to configure a secondary TACACS authentication server.  
secondary authorization  
Use the secondary authorizationcommand to configure a secondary TACACS authorization server.  
security acl  
Use the security aclcommand to set an access control list to be used by the ipsec policy and specify the  
data stream protection mode.  
IPSec Policy view  
IPSec Policy Template view  
security-policy-server  
Use the security-policy-servercommand to specify the IP address of a security policy server.  
RADIUS Scheme view  
seizure-ack  
select-mode  
Use the seizure-ackcommand to enable or disable the terminating point to send seizure  
acknowledgement signal.  
R2 CAS view  
R2 CAS view  
Use the select-modecommand to configure the E1 trunk selection mode.  
select-rule search-stop  
Use the select-rule search-stopcommand to configure the maximum number of voice entities found.  
Voice Dial Program view  
Voice Dial Program view  
Voice Dial Program view  
Voice Entity view  
select-rule type-first  
Use the select-rule type-firstcommand to configure the type-first select rules for voice entities.  
select-rule rule-order  
Use the select-rule rule-ordercommand to configure the select rule of voice entities.  
select-stop  
Use the select-stopcommand to disable the search for voice entities.  
send  
Use the sendcommand to transfer messages between user interfaces.  
Use the send allcommand to send messages to all user interfaces.  
Use the sendnumbercommand to send messages to the user interface specified by its absolute index.  
Use the sendtype-name numbercommand to send messages to the user interface specified by its  
interface type and relative index.  
User view  
 
136  
3Com Router 5000/6000 Family  
Command Reference  
send-busytone  
Use the send-busytonecommand to enable busy tone sending on the FXO interface.  
FXO Voice Subscriber-Line view  
POTS Voice Entity view  
send-number (in Voice Entity View)  
Use the send-numbercommand to configure the number sending mode.  
send-number (in Voice Subscriber-Line View)  
Use the send-numbercommand to configure the FXS voice subscriber-line to allow the FXS to send called  
numbers.  
FXS Voice Subscriber-Line View  
send-ring  
Use the send-ringcommand to enable the local end to play ringback tone.  
Use the send-trapcommand to configure the type of events that trigger trap sending.  
Use the sendatcommand to manually send AT command to the modem.  
VoIP Voice Entity view  
send-trap  
HWPing Test Group view  
sendat  
Interface (Asynchronous Serial Interface, AUX Port, or AM Interface) view  
sendloopcode  
sendpacket passroute  
sendring  
Use the sendloopcodecommand to send the remote loopback control code.  
CT1/PRI Interface view  
HWPing Test Group view  
Use the sendpacket passroutecommand to enable routing table bypass.  
Use the sendringcommand to enable or disable the terminating point to send ring-back tone or busy tone  
signal to the calling party.  
R2 CAS view  
seq-number  
Use the seq-numbercommand to enable voice packets transmitted on the local gateway to carry sequence  
numbers.  
Voice Entity view  
RADIUS view  
PVC view  
server type  
service cbr  
service data  
Use the server-typecommand to configure the RADIUS server type supported by the router.  
Use the service cbrcommand to specify PVC service type as constant bit rate (CBR).  
Use the service datacommand to enable data call service.  
Voice Entity view  
System view  
service modem-callback  
Use the service modem-callbackcommand to enable the callback function of modems.  
service type  
Use the service-typecommand to configure a service type for a particular user.  
Local User view  
Local User view  
Local User view  
service-type ftp  
service-type ppp  
service ubr  
Use the service-type ftpcommand to specify a directory accessible for the FTP user.  
Use the service-typecommand to configure the callback attribute and caller number of the PPP user.  
Use the service ubrcommand to specify the service type of PVC as Unspecified Bit Rate (UBR) and  
specify the related rate parameters.  
PVC view  
 
3Com Router 5000/6000 Family  
Command Reference  
137  
service vbr-nrt  
Use the service vbr-nrtcommand to specify the service type of PVC as Variable Bit Rate-Non Real Time  
(VBR-NRT) and specify the related rate parameters.  
PVC view  
service vbr-rt  
Use the service vbr-rt command to set the service type of PVC to Variable Bit Rate- Real Time (VBR-RT)  
and specify the related rate parameters in the PVC view.  
PVC view  
session algorithm-suite  
Use the session algorithm-suitecommand to specify the algorithm suite a session uses.  
Dvpn-Policy view  
session idle-time  
Use the session idle-timecommand to set the L2TP session idle-timeout timer. Upon expiration of this  
timer, the L2TP session is disconnected.  
L2TP Group view  
Dvpn-Policy view  
Dvpn-Policy view  
session idle-timeout  
Use the session idle-timeoutcommand to set the idle timeout time for sessions.  
session keepalive-interval  
Use the session keepalive-intervalcommand to set the keepalive interval of sessions.  
session setup-interval  
Use the session setup-intervalcommand to set the interval for sending requests to establish a session  
(Setup request). Setup request packets are sent regularly until the session is established.  
Dvpn-Policy view  
User Interface view  
IS-IS view  
set authentication password  
Use the set authentication passwordcommand to set a local authentication password.  
Use the set-overloadcommand to configure overload flag bit for the current router.  
Use the sftpcommand to establish a connection to the remote SFTP server and enter SFTP client view.  
Use the sftp server enablecommand to enable the secure FTP (SFTP) server.  
set-overload  
sftp  
System view  
sftp server enable  
System view  
sftp source-interface  
Use the sftp source-interfacecommand to specify a source interface, which must be an existing local  
interface, for the SFTP client. After that, the IP address of the specified interface is used as the source IP  
address in each packet sent by the SFTP client.  
System view  
sftp source-ip  
Use the sftp source-ipcommand to specify a source IP address for the packets sent by the SFTP client.  
This IP address must be a local IP address.  
System view  
sham-link  
shdsl mode  
shdsl psd  
Use the sham-linkcommand to configure a sham link.  
OSPF Area view  
Use the shdsl modecommand to set the operating mode of the G.SHDSL interface.  
ATM (G.SHDSL) Interface view  
Use the shdsl psdcommand to set PSD of the G.SHDSL interface working as CPE. It is not necessarily  
the same as the one set at CO.  
ATM (G.SHDSL) Interface view  
 
138  
3Com Router 5000/6000 Family  
Command Reference  
shdsl rate  
Use the shdsl ratecommand to set single-pair interface rate of the SHDSL interface or just select  
auto-negotiation mode. You can specify maximum line rate.  
ATM (G.SHDSL) Interface view  
ATM (G.SHDSL) Interface view  
ATM (G. SHDSL) Interface view  
User Interface view  
shdsl snr-margin  
shdsl wire  
shell  
Use the shdsl snr-margincommand to set a target margin to signal-to-noise ratio (SNR).  
Use the shdsl wirecommand to set the operating mode of the current G.SHDSL interface.  
Use the shellcommand to enable terminal services on the user interface.  
Use the shell priority highcommand to set command execution first.  
Use the shutdowncommand to shut down the CPOS physical interface.  
Use the shutdowncommand to shut down the Ethernet port.  
shell priority high  
System view  
shutdown  
CPOS Interface view  
Ethernet Port view  
shutdown  
shutdown  
Use the shutdowncommand to disable the current switching PVC.  
Use the shutdowncommand to shut down the interface.  
Frame Relay Switching view  
Interface view  
shutdown  
shutdown  
Use the shutdowncommand to disable the MSDP peer specified.  
MSDP view  
shutdown (in Voice Entity View)  
Use the shutdowncommand in voice entity view to configure to change the management status of specified  
voice entity from UP to DOWN.  
Voice Entity view  
shutdown (in Voice Subscriber-Line View)  
Use the shutdowncommand in voice subscriber-line view to configure the voice subscriber-line from UP to  
DOWN.  
Voice Subscriber-Line view  
signal-value  
Use the signal-value command to configure the digital E&M subscriber-line to receive and transmit the  
ABCD bits of idle signaling and seizure signaling.  
Digital E&M Voice Subscriber-Line view  
silence-th-span  
Use the silence-th-spancommand to set the silence detection parameters that have the system take  
automatic on-hook action.  
FXO Subscriber-Line view  
silent-interface  
silent interface  
simultaneous-bindings  
sip  
Use the silent-interfacecommand to disable a specified interface to transmit IS-IS packet.  
Use the silent-interfacecommand to disable an interface to transmit OSPF packet.  
Use the simultaneous-bindingscommand to enable simultaneous binding.  
IS-IS view  
OSPF view  
MR view  
Use the sipcommand to access SIP client view.  
Voice view  
 
3Com Router 5000/6000 Family  
Command Reference  
139  
sip-call  
Use the sip-callcommand to enable globally supplementary service. body style (undo command  
description goes here)  
SIP Client view  
SIP Client view  
SIP Client view  
SIP Client view  
SIP Client view  
SIP Client view  
sip-comp  
Use the sip-compcommand to configure a SIP compatibility option.  
Use the sip-compcommand to configure a SIP compatibility option.  
Use the sip-comp agentcommand to configure including user-agent field in SIP request.  
Use the sip-domaincommand to configure the domain name of a SIP server.  
Use the sip-idcommand to set ID of the local gateway and configure its SIP authentication password.  
sip-comp  
sip-comp agent  
sip-domain  
sip-id  
sip-server  
Use the sip-server command to configure address information of SIP proxy server and define call  
requests that can be accepted.  
SIP Client view  
selectlanguage  
Use the selectlanguagecommand to enable or disable the voice gateway to play the prompt language  
selection message in the voice caller number process. This command only applies to the voice caller  
number process.  
Voice Access-Number view  
Analog E&M Voice Subscriber-Line view  
System view  
slic-gain  
Use the slic-gaincommand to configure the output gain of the SLIC chip.  
Use the snmp-agentcommand to enable SNMP agent.  
snmp-agent  
snmp-agent community  
Use the snmp-agent communitycommand to configure the read/write attribute of a community, the MIB  
view that it can access, and the ACL applied to it. The configuration overwrites the old configuration of the  
community, if there is any.  
System view  
snmp-agent group  
Use the snmp-agent groupcommand to configure a new SNMP group, or to map an SNMP user or group  
to an SNMP view.  
System view  
System view  
System view  
snmp-agent local-engineid  
Use the snmp-agent local-engineidcommand to configure an engine ID for the local SNMP entity.  
snmp-agent mib-view  
Use the snmp-agent mib-viewcommand to create or update the information about a view.  
snmp-agent packet max-size  
Use the snmp-agent packet max-sizecommand to set the maximum length of the SNMP packets that the  
agent can receive/send.  
System view  
System view  
snmp-agent sys-info  
Use the snmp-agent sys-infocommand to set system information, including system contact, physical  
location of the node, and SNMP version.  
 
140  
3Com Router 5000/6000 Family  
Command Reference  
snmp-agent target-host  
Use the snmp-agent target-hostcommand to set the destination that receives SNMP notifications.  
Use the snmp-agent target-hostcommand in conjunction with the snmp-agent trap enable command.  
System view  
System view  
snmp-agent trap enable  
Use the snmp-agent trap enablecommand to enable the device to send traps and set the trap and  
notification parameters.  
snmp-agent trap enable encrypt-card  
Use the snmp-agent trap enable encrypt-cardcommand to enable SNMP agent trap function on the  
encryption card.  
System view  
System view  
System view  
snmp-agent trap enable ldp  
Use the snmp-agent trap enable ldpcommand to enable Trap function in MPLS LDP creation.  
snmp-agent trap enable lsp  
Use the snmp-agent trap enable lspcommand to enable Trap function in MPLS LSP creation.  
snmp-agent trap enable mobile-ip  
Use the snmp-agent trap enable mobile-ipcommand to enable the MIP SNMP trap function. With the  
function enabled, a trap packet is sent to the network management software whenever a security violation  
event occurs.  
System view  
System view  
snmp-agent trap enable ospf  
Use the snmp-agent trap enable ospfcommand to enable the TRAP function of OSPF.  
snmp-agent trap life  
Use the snmp-agent trap life command to set the lifetime of traps. The expired traps are discarded  
without being retained or sent.  
System view  
System view  
System view  
System view  
snmp-agent trap queue-size  
Use the snmp-agent trap queue-size command to set the length of the trap queue to the specified host.  
snmp-agent trap source  
Use the snmp-agent trap sourcecommand to specify the source address of traps.  
snmp-agent usm-user  
Use the snmp-agent usm-usercommand to add a new user to an SNMP group.  
sot counter keepalive  
Use the sot counter keepalivecommand to specify the number of keepalive checks before disconnecting  
from the peer SOT entity.  
System view  
sot gather  
Use the sot gathercommand to assign the serial interface to an existing SOT protocol group.  
Synchronous Serial Interface view  
sot group-set  
sot peer  
Use the sot group-setcommand to set up a SOT protocol group.  
System view  
Use the sot peercommand to assign an IP address to the local SOT entity.  
System view  
sot sdlc broadcast  
Use the sot sdlc broadcastcommand to configure the broadcast address FF for the connected SDLC  
terminals, allowing them to receive broadcast frames.  
Synchronous Serial Interface view  
sot sdlc controller  
Use the sot sdlc controllercommand to configure the SDLC address of a connected terminal.  
Synchronous Serial Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
141  
sot sdlc-status primary  
sot sdlc-status secondary  
sot send address  
Use the sot sdlc-status primarycommand to set the role of the router to SDLC primary node.  
Synchronous Serial Interface view  
Use the sot sdlc-status secondarycommand to set the role of the router to SDLC secondary node.  
Synchronous Serial Interface view  
Use the sot send addresscommand to configure the route for sending SDLC frames to the specified  
specific terminal.  
Synchronous Serial Interface view  
sot send all tcp  
sot timer keepalive  
source  
Use the send all tcpcommand to forward all received SDLC frames to the specified address.  
Synchronous Serial Interface view  
Use the sot timer keepalivecommand to configure the keepalive timer.  
System view  
Use the tunnel sourcecommand to specify the source IP address or source interface to be filled in the  
added IP header at the time of tunnel interface encapsulation.  
Tunnel Interface view  
source-interface  
source-ip  
Use the source-interface command to configure the source interface in the transmitted test packets.  
HWPing Test Group view  
Use the source-ipcommand to configure a source IP address for this test.  
HWPing Test Group view  
source-ip  
Use the source-ipcommand to bind a source IP address to the router when it functions as a User Agent  
(UA).  
SIP Client view  
PIM view  
source-policy  
Use the source-policycommand to configure a router to filter the multicast data packet received according  
to source (group) address.  
source-port  
Use the source-portcommand to configure a source port number for this test.  
HWPing Test Group view  
special-character  
Use the special-charactercommand to configure the supported special characters during register signal  
exchange.  
R2 CAS view  
Voice Dial Program view  
Ethernet Interface view  
Ethernet Port view  
special-service  
Use the special-servicecommand to enable or disable the special-service numbers.  
Use the speedcommand to set the operating speed of the Ethernet interface.  
Use the speedcommand to configure the rate of the port.  
Use the speedcommand to set the transmission rate on the user interface.  
speed  
speed  
speed  
User Interface view  
spf-delay-interval  
Use the spf-delay-interval command to configure the interval for actively releasing CPU in the SPF  
calculation.  
IS-IS view  
 
142  
3Com Router 5000/6000 Family  
Command Reference  
spf-schedule-interval  
Use the spf-schedule-intervalcommand to configure the route calculation interval of OSPF.  
OSPF view  
IS-IS view  
spf-slice-size  
Use the spf-slice-size command to configure whether to set slice and the duration time each time when  
IS-IS performs SPF route calculation.  
spt-switch-threshold  
Use the spt-switch-thresholdcommand to set the packet rate threshold when the PIM leaf router  
switches from the RPT to the SPT.  
PIM view  
ssh authentication-type default  
Use the ssh authentication-type defaultcommand to specify a default authentication mode for SSH  
users.  
System view  
System view  
System view  
System view  
ssh client assign rsa-key  
Use the ssh client assign rsa-keycommand to associate an SSH server with the name assigned to its  
public key. When connecting to this server, the client verifies its trustworthiness based on this association.  
ssh client first-time enable  
Use the ssh client first-time enablecommand to enable the SSH client to perform first-time  
authentication on SSH servers.  
ssh server authentication-retries  
Use the ssh server authentication-retriescommand to set the number of SSH connection  
authentication retries, which is validated at next login.  
ssh server compatible_ssh1x enable  
Use the ssh server compatible_ssh1x enablecommand to enable the SSH server to work with SSH1.X  
clients.  
System view  
System view  
ssh server rekey-interval  
Use the ssh server rekey-intervalcommand to set the interval for updating the server key.  
ssh-server source-interface  
Use the ssh-server source-interfacecommand to specify a source interface, which must be an existing  
local interface, for the SSH server. After that, the IP address of the specified interface is used as the source  
IP address in each packet sent by the SSH server.  
System view  
System view  
ssh-server source-ip  
ssh server timeout  
Use the ssh-server source-ipcommand to specify a source IP address for the packets sent by the SSH  
server. This IP address must be a local IP address.  
Use the ssh server timeoutcommand to set a timeout for SSH connection authentication at login. It  
becomes valid at next login.  
System view  
System view  
ssh user  
Use the ssh usercommand to create an SSH user.  
ssh user assign  
Use the ssh user assigncommand to assign one existing public key to a user. If a key exists, the new  
assignment overrides.  
System view  
System view  
ssh user authentication-type  
Use the ssh user authentication-typecommand to create an SSH user and specify an authentication  
mode for it.  
 
3Com Router 5000/6000 Family  
Command Reference  
143  
ssh user service-type  
Use the ssh user service-typecommand to specify service type for a user.  
System View  
System view  
ssh2  
Use the ssh2command to initiate a connection to the specified SSH server, and specify the preferred key  
exchange algorithm, encryption algorithm and HMAC algorithm between the client and the server.  
ssh2 source-interface  
Use the ssh2 source-interfacecommand to specify a source interface, which must be an existing local  
interface, for the SSH client. After that, the IP address of the specified interface is used as the source IP  
address in each packet sent by the SSH client.  
System view  
System view  
ssh2 source-ip  
Use the ssh2 source-ipcommand to specify a source IP address for the packets sent by the SSH client.  
This IP address must be a local IP address.  
standby bandwidth  
Use the standby bandwidth command to configure the actual bandwidth that the main interface uses in  
backup load sharing.  
Interface view  
Interface view  
Interface view  
standby detect-group  
standby interface  
Use the standby detect-groupcommand to implement interface backup using the auto detect function.  
Use the standby interfacecommand to specify a physical interface to back up the interface.  
standby routing-group  
Use the standby routing-groupcommand to apply a dynamic routing standby group on the secondary  
interface.  
Dial Interface view  
standby routing-rule  
Use the standby routing-rulecommand to create a dynamic routing standby group and assign a  
monitored network segment to it.  
System view  
Interface view  
standby threshold  
Use the standby thresholdcommand to configure backup load sharing on an interface or logical channel.  
standby timer delay  
Use the standby timer delaycommand to set failover and fallback delays on the interface, avoiding  
frequent switchover caused by instability of interface state.  
Interface view  
Interface view  
standby timer flow-check  
Use the standby timer flow-checkcommand to configure the interval for checking the traffic size on the  
main interface.  
standby timer routing-disable  
Use the standby timer routing-disablecommand to specify a delay for the secondary link to be  
disconnected after the primary link goes up to avoid route oscillation.  
Dial Interface view  
start l2tp  
Use the start l2tpcommand to specify conditions triggering the local end to place calls when it works as  
L2TP LAC.  
L2TP Group view  
L2TP Group view  
User view  
start l2tp tunnel  
start script  
Use the start l2tp tunnelcommand to enable the L2TP LAC to start L2TP tunnel connection.  
Use the start-scriptcommand to configure executing the specified Modem script on an interface.  
 
144  
3Com Router 5000/6000 Family  
Command Reference  
startup saved-configuration  
Use the startup saved-configurationcommand to specify the configuration file used at next startup.  
User view  
state  
Use the statecommand to configure the state of the current ISP domain or local user.  
ISP Domain view  
Local User view  
state  
state  
Use the statecommand to clarify the name of the state where an entity lies.  
Use the statecommand to configure the state of a RADIUS server.  
PKI Entity view  
RADIUS view  
static-bind ip-address  
Use the static-bind ip-addresscommand to configure an IP address for a static address binding in  
DHCP address pool view.  
DHCP Address Pool view  
static-bind { mac address | client identifier }  
Use the static-bind { mac-address | client-identifier } command to configure a MAC address or  
client identifier for a static binding.  
DHCP Address Pool view  
static-lsp egress  
Use the static-lsp egresscommand to configure a static LSP for an egress LSR.  
MPLS view  
static-lsp egress l2vpn  
Use the static-lsp egress l2vpncommand to configure a static LSP used in L2VPN for egress LSR.  
MPLS view  
MPLS view  
MPLS view  
MPLS view  
MPLS view  
PIM view  
static-lsp ingress  
Use the static-lsp ingresscommand to configure a static LSP for the ingress LSR.  
static-lsp ingress l2vpn  
Use the static-lsp egress l2vpncommand to configure a static LSP used in L2VPN for ingress LSR.  
static-lsp transit  
Use the static-lsp transitcommand to configure a static LSP for a transit LSR.  
static-lsp transit l2vpn  
Use the static-lsp transitcommand to configure a static LSP used in L2VPN for transit LSR.  
static-rp  
Use the static-rpcommand to configure static RP.  
static-rpf-peer  
Use the static-rpf-peercommand to configure static RPF peer.  
MSDP view  
statistics {interval interval | max-group number }  
Use the statistics{ interval interval| max-group number} command to configure the statistics  
interval and the maximum number of the groups of the retained statistics information according to the  
configuration.  
HWPing Test Group view  
statistics keep-time  
Use the statistics keep-timecommand to configure the retaining time of the test statistics.  
HWPing Test Group view  
stop-accounting-buffer enable  
Use the stop-accounting-buffer enablecommand to enable the router to buffer the stop-accounting  
requests that have no responses.  
RADIUS view  
 
3Com Router 5000/6000 Family  
Command Reference  
145  
stopbits  
Use the stopbitscommand to set the stop bits on the user interface.  
User Interface view  
OSPF Area view  
Voice view  
stub  
Use the stubcommand to configure the type of an OSPF area as the STUB area.  
Use the subscriber-linecommand to enter the voice subscriber-line view.  
subscriber-line  
subscriber-line  
Use the subscriber-linecommand to enter FXS, FXO, analog E&M, or digital E1/T1 voice subscriber-line  
view.  
Any Voice view except for Voice Entity view  
substitute  
Use the substitutecommand to bind the calling/called number-substitute list to the voice subscriber-line  
or voice entity.  
Voice Entity View  
Voice Subscriber-Line view  
substitute incoming-call  
Use the substitute incoming-call command to bind the calling/called numbers of the incoming calls  
from the network side to the number-substitute list.  
Voice Dial Program view  
substitute outgoing-call  
Use the substitute outgoing-call command to bind the calling/called numbers of the outgoing calls from  
the network side to the number-substitute list.  
Voice Dial Program view  
summary  
Use the summarycommand to configure automatic aggregation of sub-network routes.  
BGP Multicast view  
BGP Unicast view  
VPN Instance view  
summary  
summary  
super  
Use the summarycommand to configure IS-IS route summary.  
IS-IS view  
RIP view  
Use the summarycommand to enable RIP-2 automatic route summarization.  
Use the supercommand to switch the current user level to a specified user level, or the command level that  
the user can access.  
User view  
User Interface view  
System view  
super authentication mode  
Use the super authentication-modecommand to configure authentication mode for the super command,  
which can be configured to the following four modes:  
super password  
Use the super passwordcommand to set the password needed to switch from a lower user level to a higher  
one.  
sync-clock enable  
sync-clock interval  
synchronize arp  
Use the sync-clock enablecommand to enable clock synchronization between the router and the OSM  
board.  
GigabitEthernet Interface view  
Use the sync-clock intervalcommand to set clock synchronization interval between the router and the  
OSM board.  
GigabitEthernet Interface view  
Use the synchronize arpcommand to enable authorized ARP for global DHCP address pools.  
Global DHCP Address Pool view  
 
146  
3Com Router 5000/6000 Family  
Command Reference  
sysname  
Use the sysnamecommand to set the name of the router.  
System view  
User view  
system-view  
t1 bert  
Use the system-viewcommand to enter system view from the current user view.  
Use the t1 bertcommand to start a BERT test on the specified T1 line on the CT3 interface.  
Use the t1 channel-setcommand to bundle timeslots on the T1 channel.  
CT3 Interface view  
CPOS Interface view  
CT3 Interface view  
CT3 Interface view  
CPOS Interface view  
CT3 Interface view  
CT3 Interface view  
CPOS Interface view  
CT3 Interface view  
CPOS Interface view  
CT3 Interface view  
CT3 Interface view  
CPOS Interface view  
CT3 Interface view  
CPOS Interface view  
CT3 Interface view  
Interface view  
t1 channel-set  
t1 channel set  
t1 sendloopcode  
t1 set clock  
t1 set clock  
t1 set fdl  
Use the t1 channel-setcommand to bundle the timeslots of a T1 line.  
Use the t1 sendloopcodecommand to set the loopback mode of the specified far-end T1 line.  
Use the t1 set clockcommand to configure the clock mode of T1 channel.  
Use the t1 set clockcommand to set the clock mode for a T1 line on the CT3 interface.  
Use the t1 set fdlcommand to set the behavior of the specified T1 line on the FDL in ESF framing.  
Use the t1 set frame-formatcommand to set a frame format for T1 channel.  
Use the t1 set frame-formatcommand to configure the frame format of T1 line.  
Use the t1 set loopbackcommand to configure the loopback mode of the T1 channel.  
Use the t1 set loopbackcommand to set the loopback mode of a T1 line on the T3 interface.  
Use the t1 showcommand to view the line state of the specified T1 line on the CT3 interface.  
Use the t1 shutdowncommand to shut down a T1 channel.  
t1 set frame-format  
t1 set frame-format  
t1 set loopback  
t1 set loopback  
t1 show  
t1 shutdown  
t1 shutdown  
t1 unframed  
t1 unframed  
tcp mss  
Use the t1 shutdowncommand to shut down a T1 line on the CT3 interface.  
Use the t1 unframedcommand to set a T1 channel on the CPOS interface to unframed mode.  
Use the t1 unframedcommand to set a T1 line on the CT3 interface to work in unframed mode (T1 mode).  
Use the tcp msscommand to designate a value as a threshold for TCP packets to be fragmented.  
 
3Com Router 5000/6000 Family  
Command Reference  
147  
tcp timer fin-timeout  
Use the tcp timer fin-timeoutcommand to configure the TCP finwait timer.  
System view  
System view  
tcp timer syn-timeout  
Use the tcp timer syn-timeoutcommand to configure the TCP synwait timer.  
tcp window  
Use the tcp windowcommand to configure the size of the transceiving buffer of the connection-oriented  
Socket.  
System view  
User view  
telnet  
Use the telnetcommand to telnet from this router to another device.  
telnet-server source-interface  
Use the ftp-server source-interfacecommand to specify a source interface, which must be an existing  
local interface, for the Telnet server. After that, the IP address of the specified interface is used as the source  
IP address in each packet sent by the Telnet server.  
System view  
System view  
telnet-server source-ip  
Use the telnet-server source-ipcommand to specify a source IP address for the packets sent by the  
Telnet server. This IP address must be a local IP address.  
telnet source-interface  
Use the telnet source-interfacecommand to telnet from the main IP address of the specified interface  
to the destination IP address.  
User view  
System view  
telnet source-ip  
Use the telnet source-ipcommand to telnet from the specified source IP address to the specified  
destination IP address.  
User view  
System view  
terminal debugging  
terminal logging  
terminal monitor  
Use the terminal debuggingcommand to have the debugging information displayed on the user terminal.  
Use the terminal loggingcommand to have the log information displayed on the terminal.  
User view  
User view  
Use the terminal monitorcommand to have the terminal display debugging /log/trap information sent from  
the info-center.  
User view  
User view  
terminal trapping  
terminal type  
terminator  
Use the terminal trappingcommand to have the terminal display trap information.  
Use the terminal typecommand to set the terminal type.  
User Interface view  
Use the terminatorcommand to configure a special character string as the terminator of a telephone  
number whose length is variable.  
Voice Dial Program view  
test-enable  
Use the test-enablecommand to execute an HWPing test.  
HWPing Test Group view  
test-failtimes  
Use the test-failtimescommand to configure the number of consecutive test failures allowed before a  
trap is sent to the NMS.  
HWPing Test Group view  
 
148  
3Com Router 5000/6000 Family  
Command Reference  
test-time begin  
test-type  
tftp  
Use the test-time begincommand to configure the start time and the lasting time of a test.  
Use the test-typecommand to configure the type of the test.  
HWPing Test Group view  
HWPing Test Group view  
User view  
Use the tftpcommand to upload or download a file through TFTP.  
tftp host source-interface  
Use the tftphostsource-interfacecommand to specify the source interface that the TFTP client uses  
when accessing the specified TFTP server.  
User view  
User view  
tftp host source-ip  
Use the tftphostsource-ipcommand to specify the source IP address that the TFTP client uses when  
accessing the specified TFTP server. This source IP address must be a local address.  
tftp hostname vpn-instance  
Use the tftp hostname vpn-instanceto adopt VPN instance mode to access TFTP server and upload  
and download files.  
User view  
System view  
System view  
System view  
tftp-server acl  
Use the tftp-server aclcommand to reference an ACL to control access to the TFTP server.  
Use the tftp-server directorycommand to configure the directory TFTP Client can access.  
Use the tftp-server enablecommand to enable TFTP Server.  
tftp-server directory  
tftp-server enable  
tftp-server max-users  
Use the tftp-server max-userscommand to maximum number of concurrent users that are allowed to  
access TFTP server.  
System view  
tftp-server retry-times  
Use the tftp-server retry-timescommand to configure maximum number of retry times for TFTP server  
timeout retransmission.  
System view  
System view  
tftp-server timeout  
tftp-server update  
Use the tftp-server timeoutcommand to configure UDP packet response timeout time for TFTP server.  
Use the tftp-server updatecommand to set the file update mode that the FTP server uses while receiving  
data.  
System view  
tftp source-interface  
Use the ftp source-interfacecommand to specify a source interface, which must be an existing local  
interface, for the TFTP client.  
System view  
System view  
tftp source-ip  
time-out  
Use the ftp source-ipcommand to specify a source IP address for the packets sent by the TFTP client.  
Use the time-outcommand to configure the time waiting for a DPD acknowledgement.  
Use the time-rangecommand to specify a time range.  
DPD Structure view  
System view  
time-range  
 
3Com Router 5000/6000 Family  
Command Reference  
149  
timeout  
Use the timeoutcommand to configure a timeout time for a test.  
HWPing Test Group view  
timer (Digital E&M)  
timer configuration  
timer-dial-interval  
Use the timercommand to configure the timeout values of the signals in the digital E&M signaling.  
Digital E&M Voice Subscriber-Line view  
ES-IS view  
Use the timer configurationcommand to set the interval to send ISH packets.  
Use the timer dial-intervalcommand to configure the timer that the system waits for a subscriber to  
dial the next digit.  
Voice Subscriber-Line view  
timer dl (R2)  
Use the timer dlcommand to configure the timeout value of line signals of R2 signaling.  
Use the timer dtmfcommand to configure the time interval for sending DTMF signals.  
R2 CAS view  
R2 CAS view  
timer dtmf (R2)  
timer first-dial  
Use the timer first-dial command to configure the timer that the system waiting for a subscriber to dial  
the first digit.  
Voice Subscriber-Line view  
timer hold  
Use the timer holdcommand to set the polling interval.  
Interface view  
timer hold  
Use the timer holdcommand to configure the polling timer at the DTE side.  
Use the timer holdcommand to set the timer to send keepalive packet.  
Interface view  
timer hold  
Serial Interface view  
ES-IS view  
timer holding  
Use the timer holdingcommand to set the holding time of the information ISH packets sent carry.  
Use the timer keep-alive holdcommand to configure the Keepalive and Holdtime timer of BGP.  
timer keep-alive hold  
BGP Unicast view  
BGP Multicast view  
VPNv4 view  
VPN Instance view  
timer loop  
Use the timer loopcommand to set the auto detect interval, that is, the frequency for auto detect.  
Detect Group view  
timer lsp-max-age  
Use the timer lsp-max-age command to configure the maximum lifetime of an LSP generated by the  
current router.  
IS-IS view  
IS-IS view  
timer-lsp-refresh  
timer quiet  
Use the timer lsp-refresh command to configure the refresh interval of LSP.  
Use the timer quietcommand to set the duration that the primary server must wait before it can resume  
the active state.  
RADIUS view  
timer quiet  
Use the timer quietcommand to set the duration that a primary server must wait before it can resume the  
active state.  
TACACS+ view  
 
150  
3Com Router 5000/6000 Family  
Command Reference  
timer realtime-accounting  
timer realtime-accounting  
tUse the timer realtime-accountingcommand to configure a real-time accounting interval.  
RADIUS view  
Use the timer realtime-accountingcommand to configure a real-time accounting interval.  
TACACS+ view  
timer register-complete (R2)  
Use the timer register-completecommand to configure the timeout value for register signals of R2  
signaling.  
R2 CAS view  
timer register-pulse (R2)  
Use the timer pulse command to configure the persistence time of the register pulse signal of R2 signaling  
(A3, A4 and A6, etc.).  
R2 CAS view  
RADIUS view  
TACACS+ view  
MSDP view  
timer response-timeout  
Use the timer response-timeoutcommand to configure the RADIUS server response timer.  
timer response-timeout  
Use the timer response-timeoutcommand to set the response timeout timer of the TACACS server.  
timer retry  
Use the timer retrycommand to configure the value of connection request re-try period.  
timer ring (R2)  
Use the timer ringcommand to configure the maximum time range before the signal tone of R2 signaling  
is sent.  
R2 CAS view  
timer ring-back  
Use the timer ring-backcommand to configure the maximum duration for the system to send the ringback  
tone.  
Voice Subscriber-Line view  
timer spf  
Use the timer spfcommand to configure the interval for the SPF calculation.  
Use the timer waitcommand to set a timeout period for a probing attempt.  
IS-IS view  
timer wait  
Detect Group view  
timer wait-digit  
Use the timer wait-digitcommand to configure the maximum time duration that the system waits for a  
digit.  
Voice Subscriber-Line view  
timers  
Use the timerscommand to modify value for the three timers, Period update, Timeout and  
Garbage-collection, of RIP.  
RIP view  
timeslot-set  
Use the timeslot-setcommand to configure the timeslot set to perform R2 signaling and digital E&M  
signaling configurations.  
CE1/PRI Interface view  
Voice Entity view  
timestamp  
Use the timestampcommand to enable the local end to send voice packets with timestamps.  
Use the toscommand to assign a value to the ToS field in the header of HWPing test packets.  
tos  
HWPing Test Group view  
trace interval  
Use the trace intervalcommand to configure the interval for information recording in the debugging  
process, that is, the number of voice packets upon the pass of which a record will be made.  
Voice view  
 
3Com Router 5000/6000 Family  
Command Reference  
151  
tracert  
Use the tracertcommand to trace the gateways by which a packet passes from source to destination for  
network connectivity test and fault location.  
Any view  
Any view  
tracert clns  
Use the tracert clnscommand to track the nodes along the route that leads to a specified destination.  
Use the traffic behaviorcommand you can define a traffic behavior and enter the behavior view.  
Use the traffic classifiercommand to define a class and enter the class view.  
Use the traffic-policycommand to associate a sub-policy to the behavior.  
traffic behavior  
traffic classifier  
traffic-policy  
System view  
System view  
Traffic Behavior view  
traffic-shaping adaptation  
Use the traffic-shaping adaptationcommand to enable the adaptive traffic shaping function of frame  
relay.  
Frame Relay Class view  
traffic-share-across-interface  
Use the traffic-share-across-interfacecommand to enable RIP to distribute traffic equally on multiple  
interfaces using equal-cost routes.  
RIP Protocol view  
RIP MBGP Address Family view  
transform  
Use the transformcommand to set a security protocol used by a proposal.  
IPSec Proposal view  
translate ip  
translate x25  
transmit gain  
transmit-priority  
Use the translate ipcommand to configure an X2T forwarding route from IP network to X.25 network.  
Use the translate x25command to configure an X2T forwarding route from X.25 network to IP network.  
Use the transmit gaincommand to configure the voice subscriber-line output end gain value.  
System view  
System view  
Voice Subscriber-Line view  
Use the transmit-prioritycommand to assign a transmit priority to the ATM PVC associated with the  
UBR, VBR-T, or VBR-NRT service. The higher priority PVC is allocated bandwidth before any other PVCs.  
ATM PVC view  
R2 CAS view  
trunk-direction  
trunk-id  
Use the trunk-directioncommand to configure the E1 trunk direction.  
Use the trunk-idcommand to configure the number that the local end dials to call the PSTN side in FRF.11  
trunk mode.  
Voice Entity view  
R2 CAS view  
ts  
Use the tscommand to maintain the trunk circuit of the specified timeslot.  
Use the ttlcommand to configure TTL of ICMP test packets.  
ttl  
HWPing Test Group view  
ttl expiration  
Use the ttl expirationcommand to configure the router to forward ICMP responses by local IP routing  
when the MPLS TTL expires.  
MPLS view  
 
152  
3Com Router 5000/6000 Family  
Command Reference  
ttl propagate  
Use the ttl propagatecommand to enable IP TTL duplication of MPLS.  
MPLS view  
tunnel authentication  
Use the l2tp tunnel authenticationcommand to enable L2TP tunnel authentication.  
L2TP Group view  
tunnel avp-hidden  
Use the tunnel avp-hiddencommand to configure Attribute Value Pair (AVP) data to be transmitted in  
hidden format.  
L2TP Group view  
L2TP Group view  
tunnel flow-control  
tunnel local  
Use the tunnel flow-controlcommand to enable L2TP tunnel flow-control.  
Use the tunnel localcommand to set the local address of an ipsec policy.  
Manually-Established IPSec Policy view  
tunnel keepstanding  
Use the tunnel keepstanding command to enable the tunnel-hold function of L2TP, preventing the tunnel  
from being disconnected when no session is present.  
L2TP Group view  
L2TP Group view  
tunnel name  
Use the tunnel namecommand to specify local name of a tunnel.  
tunnel-on  
Use the tunnel-oncommand to enable tunnel function.  
VoIP Voice Entity view  
L2TP Group view  
tunnel password  
tunnel-protocol dvpn  
tunnel-protocol gre  
tunnel remote  
tunnel timer hello  
type  
Use the tunnel passwordcommand to specify a password for tunnel authentication.  
Use the tunnel-protocol udp dvpncommand to encapsulate a tunnel interface with UDP DVPN.  
Use the tunnel modecommand to set encapsulation mode of the tunnel interface to GRE.  
Use the tunnel remotecommand to set the remote address of an ipsec policy.  
Tunnel Interface view  
Tunnel interface view  
Manually-Established IPSec Policy view  
Use the tunnel timer hellocommand to set a Hello packet forwarding interval.  
Use the typecommand to configure the analog E&M subscriber-line signal type.  
L2TP Group view  
Voice Subscriber-Line view  
type-number  
Use the type-numbercommand to configure the calling/called number types of voice entities.  
Use the udp-helper enablecommand to enable UDP Helper.  
Voice Entity view  
System view  
udp-helper enable  
udp-helper port  
Use the udp-helper portcommand to specify the UDP port number in the UDP broadcasts to be  
forwarded.  
System view  
udp-helper server  
Use the udp-helper servercommand to configure the destination server to which the UDP broadcasts  
received on the interface are forwarded.  
Ethernet Interface view  
 
3Com Router 5000/6000 Family  
Command Reference  
153  
undelete  
Use the undeletecommand to restore a file from the recycle bin.  
User view  
User view  
undo schedule reboot  
undo synchronization  
Use the undo schedule rebootcommand to cancel the configuration of the schedule reboot terminal  
service.  
Use the undo synchronizationcommand to remove the synchronization between BGP and IBGP.  
BGP view  
VPN Instance view  
upgrade  
Use the upgradecommand to upgrade the Boot ROM program, pico-code or the logic.  
Use the upgradecommand to upgrade the Boot ROM.  
System view  
User view  
upgrade  
upgrade flash  
Use the upgrade flash command to upgrade the software of the card. To have the upgraded software take  
effect, reboot the router.  
ATM (ADSL) Interface view  
use encrypt-card  
Use the use encrypt-cardcommand to specify the SA proposal uses the encryption card at a designated  
slot.  
Card SA Proposal view  
user  
user  
Use the usercommand to register an FTP user.  
FTP Client view  
Use the usercommand to configure username, password and corresponding display mode in SIP client  
view and/or voice entity view. The configurations of the cnonce and realm authentication information fields  
are optional, which can be used for authentication.  
SIP Client view  
Voice Entity view  
user-interface  
Use the user-interfacecommand to enter single-user interface view or multi-user interface view.  
System view  
user-name-format  
Use the user-name-formatcommand to configure the format of the username to be sent to a RADIUS  
server.  
RADIUS view  
user-name-format  
user privilege  
Use the user-name-formatcommand to configure the username format sent to the TACACS server.  
TACACS+ view  
Use the user privilege command to configure the command level that the login users on the current user  
interface can access.  
User Interface view  
username  
Use the usernamecommand to configure a name used for logging onto the FTP server.  
HWPing Test Group view  
CE1/PRI Interface view  
CE3 Interface view  
using (CE1/PRI Interface)  
Use the usingcommand to configure the operating mode of the CE1/PRI interface.  
using (CE3 Interface)  
Use the usingcommand to configure the operating mode of a CE3 interface.  
 
154  
3Com Router 5000/6000 Family  
Command Reference  
using (CT3 Interface)  
Use the usingcommand to configure the operating mode of a CT3 interface.  
CT3 Interface view  
Voice Entity view  
vad-on  
Use the vad-oncommand to enable silence detection function.  
validate source address  
Use the validate-source-addresscommand to enable checking of the source address of a RIP packet  
upon reception.  
RIP Protocol view  
RIP MBGP Address Family view  
verbose  
Use the verbosecommand to enable the verbose function to view information from the FTP server.  
FTP Client view  
System view  
vfs check check-method discard  
Use the vfs check check-method discardcommand to specify the file discarding method to be the file  
system check method.  
vfs check check-method discard auto  
Use the vfs check check-method discard autocommand to specify to discard the contents of corrupted  
files and then recycle the corresponding storage space automatically.  
System view  
System view  
vfs check check-method fix  
Use the vfs check check-method fixcommand to set the file check method to automatic file fixing.  
vfs check file-system  
Use the vfs check file-systemcommand to check the file system. At present, the system can check  
corrupted files and perform operations such as file fixing/discarding and space recycling.  
User view  
vi-card busy-tone-detect  
Use the vi-card busy-tone-detectcommand to configure busy tone detection method on FXO  
subscriber-line.  
Voice view  
Voice view  
vi-card cptone-custom  
Use the vi-card cptone-customcommand to set the prompt tone parameters of the system.  
vi-card custom-toneparam  
Use the vi-card custom-toneparamcommand to save DSP parameters and customize busy tone  
detection parameters on the FXO interface.  
Voice view  
Voice view  
vi-card reboot  
virtualbaudrate  
vlan-type dot1q vid  
vlink-peer  
Use the vi-card rebootcommand to reboot a voice card.  
Use the virtualbaudratecommand to set a virtual baudrate for the DTE interface.  
Use the vlan-type dot1q command to set the encapsulation types on the sub-interface.  
Use the vlink-peercommand to create and configure a virtual link.  
Use the vofrcommand to enable VoFR operation mode for a DLCI.  
Synchronous Serial Interface view  
Interface view  
OSPF Area view  
vofr  
DLCI view  
vofr frf11-timer  
Use the vofr frf11-timercommand to configure the interval of Trunk Wait timer in FRF.11 trunk mode.  
Voice view  
 
3Com Router 5000/6000 Family  
Command Reference  
155  
vofr jitter-buffer  
Use the vofr jitter-buffercommand to configure a jitter buffer length.  
Voice view  
voice bandwidth  
voice-config  
Use the voice bandwidthcommand to configure maximum bandwidth for voice calls.  
Frame Relay Class view  
Use the voice-configcommand to enable the DHCP server to send option 184 and suboptions of 184  
when it assigns addresses from the global address pool.  
DHCP Address Pool view  
voice-setup  
Use the voice-setupcommand to enter voice view and enable voice services.  
System view  
voip call-start  
voip calledtunnel  
Use the voip call-startcommand to configure a call initialization mode for the called GW.  
Use the voip calledtunnel enablecommand to enable the tunnel function on the called gateway.  
Voice view  
Voice view  
voip h323-conf tcs-t38  
Use the voip h323-conf tcs-t38command to enable the voice gateway to include the T.38 capability  
description in its capability set when it is in H.323 slow-start mode.  
Voice view  
Voice view  
Voice view  
voip h323-descriptor  
Use the voip h323-descriptorcommand to configure the description character string of the voice gateway  
H.323.  
voip timer  
Use the voip timercommand to set the VoIP-to-POTS timer, or the delay waiting for switching from VoIP  
entity to backup POTS entity after a VoIP call is failed.  
vpinstance  
Use the vpninstancecommand to specify a VPN instance.  
HWPing Test Group view  
OSPF Protocol view  
MBGP VPN-Instance view  
Voice view  
vpn-instance-capability simple  
Use the routing-table limitcommand to configure a router as Multi-VPN-Instance CE.  
vpn-target  
Use the vpn-targetcommand to create vpn-target extended community for vpn-instance.  
Use the vqa data-statisticcommand to enable counting of voice data.  
vqa data-statistic  
vqa dscp  
Use the vqa dscpcommand to set the global DSCP value in the ToS field in the IP packets that carry the  
RTP stream or voice signaling.  
Voice view  
Voice view  
Voice view  
vqa dsp-monitor  
vqa jitter-buffer  
vqa performance  
Use the vqa dsp-monitorcommand to set duration for DSP buffer data monitoring.  
Use the vqa jitter-buffercommand to configure jitter buffer depth.  
Use the vqa performancecommand to configure the sending or receiving process of voice data to fast or  
normal forwarding process.  
Voice view  
 
156  
3Com Router 5000/6000 Family  
Command Reference  
vrbd  
Use the vrbdcommand to view software version details, including product software version and the  
matched platform software version.  
Any view  
vrrp authentication-mode  
Use the vrrp authentication-modecommand to configure authentication mode and authentication key for  
the VRRP standby groups on the interface.  
Ethernet Interface view  
Bridge Template view  
vrrp ping-enable  
vrrp un-check ttl  
Use the vrrp ping-enablecommand to enable users to ping the virtual IP addresses of standby groups.  
System view  
Bridge Template view  
Use the vrrp un-check ttlcommand to disable the VRRP standby group to check the TTL field in VRRP  
packets.  
Ethernet Interface view  
Bridge Template view  
vrrp vrid preempt-mode  
Use the vrrp vrid preempt-modecommand to enable preemption on the router and configure its  
preemption delay in the specified standby group.  
Interface view  
bridge Template view  
vrrp vrid priority  
Use the vrrp vrid prioritycommand to configure the priority of the router in the specified standby group.  
Ethernet Interface view  
Bridge Template view  
vrrp vrid timer advertise  
Use the vrrp vrid timer advertisecommand to configure the Adver_Timer of the specified standby  
group.  
Ethernet Interface view  
Bridge Template view  
vrrp vrid track  
Use the vrrp vrid trackcommand to configure the interface to be tracked.  
Ethernet Interface view  
Bridge Template view  
vrrp vrid track detect-group  
Use the vrrp vridcommand to implement VRRP using the auto detect function.  
Ethernet Interface view  
vrrp vrid virtual-ip  
Use the vrrp vrid virtual-ipcommand to create a standby group the first time that you add a virtual IP  
address or add a virtual IP address to it after that. Each standby group can accommodate up to 16 virtual  
IP addresses.  
Ethernet Interface view  
Bridge Template view  
web java-blocking acl-number  
Use the web java-blocking acl-numbercommand to enable ACL-based Java blocking ACL function.  
System view  
web java-blocking enable  
Use the web java-blocking enablecommand to enable Java blocking.  
System view  
web java-blocking extension add  
Use the web java-blocking extension addcommand to add extension name of Java request packets to  
be blocked.  
System view  
System view  
web java-blocking extension add-default  
Use the the web java-blocking extension add-defaultcommand to add system default Java blocking  
keywords after you have defined them.  
 
3Com Router 5000/6000 Family  
Command Reference  
157  
web java-blocking extension delete  
Use the web java-blocking extension deletecommand to delete a previously added extension name  
of Java request packets.  
System view  
web java-blocking extension delete-all  
Use the web java-blocking extension delete-allcommand to delete all Java blocking keywords  
previously added.  
System view  
System view  
System view  
System view  
System view  
web java-blocking extension load-file  
Use the web java-blocking extension load-filecommand to load a Java blocking filter file.  
web java-blocking extension save-file  
Use the web java-blocking extension save-filecommand save a Java blocking filter file.  
Use the web log enablecommand to enable web logging and create a logging timer.  
Use the web log timercommand to configure the timeout time of the logging timer.  
web log enable  
web log timer  
web url-filter host acl-number  
Use the web url-filter host acl-numbercommand to configure the firewall to filter the web requests  
whose destination URL address is an IP address by using an ACL.  
System view  
System view  
web url-filter host add  
Use the web url-filter host addcommand to add web filtering address, and set the filtering operation.  
web url-filter host default  
Use the web url-filter host defaultcommand to permit or deny packets that do not match with the  
URL addresses configured by the administrator.  
System view  
System view  
System view  
System view  
web url-filter host delete  
Use the web url-filter host deletecommand to a URL address filtering entry previously added.  
web url-filter host delete-all  
Use the web url-filter host delete-allcommand to delete all URL address filtering entries.  
web url-filter host enable  
Use the web url-filter host enablecommand to enable URL address filtering.  
web url-filter host ip-address  
Use the web url-filter host ip-addresscommand to configure whether to permit a web request whose  
destination URL address is an IP address to pass.  
System view  
System view  
System view  
System view  
web url-filter host load-file  
Use the web url-filter host load-filecommand to load the URL address filtering file.  
web url-filter host save-file  
Use the web url-filter host save-filecommand to save a URL address filter file.  
web url-filter parameter add  
Use the web url-filter parameter addcommand to add a keyword for URL parameter filtering.  
web url-filter parameter add-default  
Use the web url-filter parameter add-defaultcommand to add default filter keywords ^select^,  
^insert^, ^update^, ^delete^, ^drop^, --, ', ^exec^ and %27 to facilitate the user to input these keywords from  
being carelessly deleted or to enable the user to restore the default settings quickly if the web url-filter  
parameter add-defaultcommand was improperly executed.  
System view  
 
158  
3Com Router 5000/6000 Family  
Command Reference  
web url-filter parameter delete  
Use the web url-filter parameter deletecommand to delete a filter keyword previously added.  
System view  
System view  
web url-filter parameter delete-all  
Use the web url-filter parameter delete-allcommand to delete all filter keywords.  
web url-filter parameter enable  
Use the web url-filter parameter enablecommand to enable URL parameter filtering.  
System view  
web url-filter parameter load-file  
Use the web url-filter parameter load-filecommand to load a URL parameter filtering file.  
System view  
web url-filter parameter save-file  
Use the web url-filter parameter save-filecommand to save a URL parameter filter file.  
System view  
wfq  
Use the wfqcommand to set the queue type of the VC to be WFQ.  
Frame Relay Class view  
wildcard-register enable  
Use the wildcard-register enablecommand to enable fuzzy (wildcard) telephone number registration.  
SIP Client view  
wred  
Use the wredcommand to configure drop mode as weighted random early detection (WRED).  
Traffic Behavior view  
wred dscp  
Use the wred dscpcommand to set DSCP lower-limit, upper-limit and drop probability denominator of  
WRED.  
Traffic Behavior view  
Traffic Behavior view  
wred ip-precedence  
Use the wred ip-precedence command to set precedence lower-limit, upper-limit and drop probability  
denominator of WRED.  
wred weighting-constant  
Use the wred weighting-constant command to set exponential for the calculation of average queue  
length by WRED.  
Traffic Behavior view  
Interface view  
x25 alias-policy  
x25 call-facility  
Use the x25 alias-policycommand to configure the alias of an X.121 address.  
Use the x25 call-facility command to set user options for an X.25 interface. After an option is set, all  
X.25 calls from the X.25 interface will carry the relevant information field in call packet.  
Interface view  
Interface view  
x25 cug-service  
Use the x25 cug-servicecommand to enable CUG service and suppression policies.  
x25 default-protocol  
Use the x25 default-protocolcommand to set the default upper-layer protocol carried over X.25 for the  
X.25 interface.  
Interface view  
x25 default-protocol  
Use the x25 default-protocolcommand to set the upper layer protocol for an X.25 interface that X.25  
protocol carries by default.  
Interface view  
System view  
x25 hunt-group  
Use the x25 hunt-group command to create or enter an X.25 hunt group.  
 
3Com Router 5000/6000 Family  
Command Reference  
159  
x25 ignore called-address  
Use the x25 ignore called-address command to enable it to ignore the X.121 address of the called DTE  
when X.25 initiates calls.  
Interface view  
Interface view  
Interface view  
x25 ignore calling-address  
Use the x25 ignore calling-address command to enable it to ignore the X.121 address of the calling  
DTE when X.25 initiates calls.  
x25 local-cug  
Use the x25 local-cugcommand to configure mapping from local CUG to network CUG and define its  
suppression rule.  
x25 map  
Use the x25 mapcommand to set the address mapping between IP address used by LANs and X.121  
address.  
Interface view  
Interface view  
Interface view  
Interface view  
Interface view  
Interface view  
Interface view  
x25 map bridge  
x25 map clns  
x25 modulo  
Use the x25 map bridgecommand to map an X.121 address to a bridge-set.  
Use the x25 map clnscommand to configure a CLNS address mapping for an X.121 address.  
Use the x25 modulocommand to set the window modulus of an X.25 interface.  
Use the x25 packet-sizecommand to set the maximum input and output packet lengths of X.25 interface.  
Use the x25 pvccommand to configure one PVC route encapsulated with datagram.  
Use the x25 pvccommand to configure an X.25 PVC route.  
x25 packet-size  
x25 pvc  
x25 pvc  
x25 qllc-switch  
Use the X25 qllc-switchcommand to create a QLLC switching map entry, an association of X.121  
address, MAC address of the SNA device, and local virtual MAC address.  
Synchronous Serial Interface view  
x25 queue-length  
Use the x25 queue-lengthcommand to set the data queue length on X.25 VC.  
Interface view  
x25 receive-threshold  
Use the x25 receive-thresholdcommand to set the number of receivable maximum packets before X.25  
sends the acknowledged packet.  
Interface view  
Interface view  
Interface view  
Interface view  
x25 response called-address  
Use the x25 response called-addresscommand to enable X.25 to carry the address information of the  
called DTE in sending call reception packet.  
x25 response calling-address  
Use the x25 response calling-addresscommand to enable X.25 to carry the address information of the  
calling DTE in sending call reception packet.  
x25 reverse-charge-accept  
Use the x25 reverse-charge-acceptcommand to enable this interface to accept the call with “reverse  
charging request”, the information added by some certain user facilities.  
 
160  
3Com Router 5000/6000 Family  
Command Reference  
x25 roa-list  
Use the x25 roa-listcommand to define ROA list.  
System view  
Interface view  
x25 switch pvc  
Use the x25 switch pvc(packet switching) command to configure one PVC route.  
x25 switch svc hunt-group  
Use the x25 switch svc hunt-groupcommand to add an X.25 switching route whose forwarding address  
is a hunt group.  
System view  
System view  
x25 switch svc interface  
Use the x25 switch svc interfacecommand to add an X.25 switching route whose forwarding address  
is a serial interface or Annex G DLCI.  
x25 switch svc xot  
Use the x25 switch svc xotcommand to add an X.25 switching route whose forwarding address is XOT  
channel.  
System view  
System view  
x25 switching  
x25 template  
Use the x25 switchingcommand to enable the X.25 switching function.  
Use the x25 templatecommand in system view to create an X.25 template and in DLCI view to reference  
the template.  
System view  
DLCI view  
x25 timer hold  
x25 timer idle  
x25 timer tx0  
x25 timer tx1  
Use the x25 timer holdcommand to set the delay to send calls to a destination with failed calls.  
Use the x25 timer idlecommand to set the maximum idle time of the SVC on the interface.  
Use the x25 timer tx0command to set the restart/retransmission timer delay for DTE (or DCE).  
Interface view  
Interface view  
Interface view  
Use the x25 timer tx1command to set calling request (indication) transmission timer delay for DTE (or  
DCE).  
Interface view  
Interface view  
Interface view  
x25 timer tx2  
x25 timer tx3  
x25 vc-per-map  
Use the x25 timer tx2command to set resetting request (indication) transmission timer delay for DTE (or  
DCE).  
Use the x25 timer tx3command to set clearing request (indication) transmission timer delay for DTE (or  
DCE).  
Use the x25 vc-per-mapcommand to set the maximum number of VCs for connections with the same  
destination device.  
Interface view  
Interface view  
Interface view  
x25 vc-range  
Use the x25 vc-rangecommand to set highest and lowest values of X.25 VC range.  
x25 window-size  
Use the x25 window-sizecommand to set the sizes of input and output windows on the interface X.25.  
 
3Com Router 5000/6000 Family  
Command Reference  
161  
x25 x121-address  
Use the x25 x121-addresscommand to set the X.121 address of an X.25 interface.  
Interface view  
x25 xot pvc  
Use the x25 xot pvccommand to add a PVC route of XOT. Use the undo x25 pvccommand to delete the  
specified PVC route of XOT.  
Interface view  
System view  
x29 timer idleclear  
Use the x29 timer idleclearcommand to set the idle-clear timer for PAD connection.  
x29 timer inviteclear-time  
Use the x29 timer inviteclear-timecommand to set the delay waiting for response after the PAD clear  
procedure is initiated. Upon expiration of this timer, the server aborts the connection by force and starts X.25  
clear procedures.  
System view  
User view  
xmodem get  
Use the xmodem getcommand to download a file by using Xmodem through the AUX port. Comware  
supports 128-byte packets and CRC check.  
 
162  
3Com Router 5000/6000 Family  
Command Reference  
 

3Com Network Card WL 601 User Manual
Adcom Stereo Amplifier GFA 7000 User Manual
Agilent Technologies Switch 34980A User Manual
Altinex Network Card CP451 008 User Manual
Altinex Switch 400 0226 003 User Manual
American Standard Bathroom Aids 2722102 RHO User Manual
Axis Communications Security Camera Q1615 E User Manual
Axxess Interface Whiteboard Accessories 8690 User Manual
Baratza Coffeemaker G385 User Manual
Barco Projector Accessories R9841770 User Manual